diff options
Diffstat (limited to 'drivers/misc/eeprom')
| -rw-r--r-- | drivers/misc/eeprom/Kconfig | 59 | ||||
| -rw-r--r-- | drivers/misc/eeprom/Makefile | 4 | ||||
| -rw-r--r-- | drivers/misc/eeprom/at24.c | 582 | ||||
| -rw-r--r-- | drivers/misc/eeprom/at25.c | 389 | ||||
| -rw-r--r-- | drivers/misc/eeprom/eeprom.c | 257 | ||||
| -rw-r--r-- | drivers/misc/eeprom/eeprom_93cx6.c | 240 |
6 files changed, 1531 insertions, 0 deletions
diff --git a/drivers/misc/eeprom/Kconfig b/drivers/misc/eeprom/Kconfig new file mode 100644 index 00000000000..c76df8cda5e --- /dev/null +++ b/drivers/misc/eeprom/Kconfig @@ -0,0 +1,59 @@ +menu "EEPROM support" + +config EEPROM_AT24 + tristate "I2C EEPROMs from most vendors" + depends on I2C && SYSFS && EXPERIMENTAL + help + Enable this driver to get read/write support to most I2C EEPROMs, + after you configure the driver to know about each EEPROM on + your target board. Use these generic chip names, instead of + vendor-specific ones like at24c64 or 24lc02: + + 24c00, 24c01, 24c02, spd (readonly 24c02), 24c04, 24c08, + 24c16, 24c32, 24c64, 24c128, 24c256, 24c512, 24c1024 + + Unless you like data loss puzzles, always be sure that any chip + you configure as a 24c32 (32 kbit) or larger is NOT really a + 24c16 (16 kbit) or smaller, and vice versa. Marking the chip + as read-only won't help recover from this. Also, if your chip + has any software write-protect mechanism you may want to review the + code to make sure this driver won't turn it on by accident. + + If you use this with an SMBus adapter instead of an I2C adapter, + full functionality is not available. Only smaller devices are + supported (24c16 and below, max 4 kByte). + + This driver can also be built as a module. If so, the module + will be called at24. + +config EEPROM_AT25 + tristate "SPI EEPROMs from most vendors" + depends on SPI && SYSFS + help + Enable this driver to get read/write support to most SPI EEPROMs, + after you configure the board init code to know about each eeprom + on your target board. + + This driver can also be built as a module. If so, the module + will be called at25. + +config EEPROM_LEGACY + tristate "Old I2C EEPROM reader" + depends on I2C && SYSFS + help + If you say yes here you get read-only access to the EEPROM data + available on modern memory DIMMs and Sony Vaio laptops via I2C. Such + EEPROMs could theoretically be available on other devices as well. + + This driver can also be built as a module. If so, the module + will be called eeprom. + +config EEPROM_93CX6 + tristate "EEPROM 93CX6 support" + help + This is a driver for the EEPROM chipsets 93c46 and 93c66. + The driver supports both read as well as write commands. + + If unsure, say N. + +endmenu diff --git a/drivers/misc/eeprom/Makefile b/drivers/misc/eeprom/Makefile new file mode 100644 index 00000000000..539dd8f8812 --- /dev/null +++ b/drivers/misc/eeprom/Makefile @@ -0,0 +1,4 @@ +obj-$(CONFIG_EEPROM_AT24) += at24.o +obj-$(CONFIG_EEPROM_AT25) += at25.o +obj-$(CONFIG_EEPROM_LEGACY) += eeprom.o +obj-$(CONFIG_EEPROM_93CX6) += eeprom_93cx6.o diff --git a/drivers/misc/eeprom/at24.c b/drivers/misc/eeprom/at24.c new file mode 100644 index 00000000000..d4775528abc --- /dev/null +++ b/drivers/misc/eeprom/at24.c @@ -0,0 +1,582 @@ +/* + * at24.c - handle most I2C EEPROMs + * + * Copyright (C) 2005-2007 David Brownell + * Copyright (C) 2008 Wolfram Sang, Pengutronix + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/module.h> +#include <linux/slab.h> +#include <linux/delay.h> +#include <linux/mutex.h> +#include <linux/sysfs.h> +#include <linux/mod_devicetable.h> +#include <linux/log2.h> +#include <linux/bitops.h> +#include <linux/jiffies.h> +#include <linux/i2c.h> +#include <linux/i2c/at24.h> + +/* + * I2C EEPROMs from most vendors are inexpensive and mostly interchangeable. + * Differences between different vendor product lines (like Atmel AT24C or + * MicroChip 24LC, etc) won't much matter for typical read/write access. + * There are also I2C RAM chips, likewise interchangeable. One example + * would be the PCF8570, which acts like a 24c02 EEPROM (256 bytes). + * + * However, misconfiguration can lose data. "Set 16-bit memory address" + * to a part with 8-bit addressing will overwrite data. Writing with too + * big a page size also loses data. And it's not safe to assume that the + * conventional addresses 0x50..0x57 only hold eeproms; a PCF8563 RTC + * uses 0x51, for just one example. + * + * Accordingly, explicit board-specific configuration data should be used + * in almost all cases. (One partial exception is an SMBus used to access + * "SPD" data for DRAM sticks. Those only use 24c02 EEPROMs.) + * + * So this driver uses "new style" I2C driver binding, expecting to be + * told what devices exist. That may be in arch/X/mach-Y/board-Z.c or + * similar kernel-resident tables; or, configuration data coming from + * a bootloader. + * + * Other than binding model, current differences from "eeprom" driver are + * that this one handles write access and isn't restricted to 24c02 devices. + * It also handles larger devices (32 kbit and up) with two-byte addresses, + * which won't work on pure SMBus systems. + */ + +struct at24_data { + struct at24_platform_data chip; + bool use_smbus; + + /* + * Lock protects against activities from other Linux tasks, + * but not from changes by other I2C masters. + */ + struct mutex lock; + struct bin_attribute bin; + + u8 *writebuf; + unsigned write_max; + unsigned num_addresses; + + /* + * Some chips tie up multiple I2C addresses; dummy devices reserve + * them for us, and we'll use them with SMBus calls. + */ + struct i2c_client *client[]; +}; + +/* + * This parameter is to help this driver avoid blocking other drivers out + * of I2C for potentially troublesome amounts of time. With a 100 kHz I2C + * clock, one 256 byte read takes about 1/43 second which is excessive; + * but the 1/170 second it takes at 400 kHz may be quite reasonable; and + * at 1 MHz (Fm+) a 1/430 second delay could easily be invisible. + * + * This value is forced to be a power of two so that writes align on pages. + */ +static unsigned io_limit = 128; +module_param(io_limit, uint, 0); +MODULE_PARM_DESC(io_limit, "Maximum bytes per I/O (default 128)"); + +/* + * Specs often allow 5 msec for a page write, sometimes 20 msec; + * it's important to recover from write timeouts. + */ +static unsigned write_timeout = 25; +module_param(write_timeout, uint, 0); +MODULE_PARM_DESC(write_timeout, "Time (in ms) to try writes (default 25)"); + +#define AT24_SIZE_BYTELEN 5 +#define AT24_SIZE_FLAGS 8 + +#define AT24_BITMASK(x) (BIT(x) - 1) + +/* create non-zero magic value for given eeprom parameters */ +#define AT24_DEVICE_MAGIC(_len, _flags) \ + ((1 << AT24_SIZE_FLAGS | (_flags)) \ + << AT24_SIZE_BYTELEN | ilog2(_len)) + +static const struct i2c_device_id at24_ids[] = { + /* needs 8 addresses as A0-A2 are ignored */ + { "24c00", AT24_DEVICE_MAGIC(128 / 8, AT24_FLAG_TAKE8ADDR) }, + /* old variants can't be handled with this generic entry! */ + { "24c01", AT24_DEVICE_MAGIC(1024 / 8, 0) }, + { "24c02", AT24_DEVICE_MAGIC(2048 / 8, 0) }, + /* spd is a 24c02 in memory DIMMs */ + { "spd", AT24_DEVICE_MAGIC(2048 / 8, + AT24_FLAG_READONLY | AT24_FLAG_IRUGO) }, + { "24c04", AT24_DEVICE_MAGIC(4096 / 8, 0) }, + /* 24rf08 quirk is handled at i2c-core */ + { "24c08", AT24_DEVICE_MAGIC(8192 / 8, 0) }, + { "24c16", AT24_DEVICE_MAGIC(16384 / 8, 0) }, + { "24c32", AT24_DEVICE_MAGIC(32768 / 8, AT24_FLAG_ADDR16) }, + { "24c64", AT24_DEVICE_MAGIC(65536 / 8, AT24_FLAG_ADDR16) }, + { "24c128", AT24_DEVICE_MAGIC(131072 / 8, AT24_FLAG_ADDR16) }, + { "24c256", AT24_DEVICE_MAGIC(262144 / 8, AT24_FLAG_ADDR16) }, + { "24c512", AT24_DEVICE_MAGIC(524288 / 8, AT24_FLAG_ADDR16) }, + { "24c1024", AT24_DEVICE_MAGIC(1048576 / 8, AT24_FLAG_ADDR16) }, + { "at24", 0 }, + { /* END OF LIST */ } +}; +MODULE_DEVICE_TABLE(i2c, at24_ids); + +/*-------------------------------------------------------------------------*/ + +/* + * This routine supports chips which consume multiple I2C addresses. It + * computes the addressing information to be used for a given r/w request. + * Assumes that sanity checks for offset happened at sysfs-layer. + */ +static struct i2c_client *at24_translate_offset(struct at24_data *at24, + unsigned *offset) +{ + unsigned i; + + if (at24->chip.flags & AT24_FLAG_ADDR16) { + i = *offset >> 16; + *offset &= 0xffff; + } else { + i = *offset >> 8; + *offset &= 0xff; + } + + return at24->client[i]; +} + +static ssize_t at24_eeprom_read(struct at24_data *at24, char *buf, + unsigned offset, size_t count) +{ + struct i2c_msg msg[2]; + u8 msgbuf[2]; + struct i2c_client *client; + int status, i; + + memset(msg, 0, sizeof(msg)); + + /* + * REVISIT some multi-address chips don't rollover page reads to + * the next slave address, so we may need to truncate the count. + * Those chips might need another quirk flag. + * + * If the real hardware used four adjacent 24c02 chips and that + * were misconfigured as one 24c08, that would be a similar effect: + * one "eeprom" file not four, but larger reads would fail when + * they crossed certain pages. + */ + + /* + * Slave address and byte offset derive from the offset. Always + * set the byte address; on a multi-master board, another master + * may have changed the chip's "current" address pointer. + */ + client = at24_translate_offset(at24, &offset); + + if (count > io_limit) + count = io_limit; + + /* Smaller eeproms can work given some SMBus extension calls */ + if (at24->use_smbus) { + if (count > I2C_SMBUS_BLOCK_MAX) + count = I2C_SMBUS_BLOCK_MAX; + status = i2c_smbus_read_i2c_block_data(client, offset, + count, buf); + dev_dbg(&client->dev, "smbus read %zu@%d --> %d\n", + count, offset, status); + return (status < 0) ? -EIO : status; + } + + /* + * When we have a better choice than SMBus calls, use a combined + * I2C message. Write address; then read up to io_limit data bytes. + * Note that read page rollover helps us here (unlike writes). + * msgbuf is u8 and will cast to our needs. + */ + i = 0; + if (at24->chip.flags & AT24_FLAG_ADDR16) + msgbuf[i++] = offset >> 8; + msgbuf[i++] = offset; + + msg[0].addr = client->addr; + msg[0].buf = msgbuf; + msg[0].len = i; + + msg[1].addr = client->addr; + msg[1].flags = I2C_M_RD; + msg[1].buf = buf; + msg[1].len = count; + + status = i2c_transfer(client->adapter, msg, 2); + dev_dbg(&client->dev, "i2c read %zu@%d --> %d\n", + count, offset, status); + + if (status == 2) + return count; + else if (status >= 0) + return -EIO; + else + return status; +} + +static ssize_t at24_bin_read(struct kobject *kobj, struct bin_attribute *attr, + char *buf, loff_t off, size_t count) +{ + struct at24_data *at24; + ssize_t retval = 0; + + at24 = dev_get_drvdata(container_of(kobj, struct device, kobj)); + + if (unlikely(!count)) + return count; + + /* + * Read data from chip, protecting against concurrent updates + * from this host, but not from other I2C masters. + */ + mutex_lock(&at24->lock); + + while (count) { + ssize_t status; + + status = at24_eeprom_read(at24, buf, off, count); + if (status <= 0) { + if (retval == 0) + retval = status; + break; + } + buf += status; + off += status; + count -= status; + retval += status; + } + + mutex_unlock(&at24->lock); + + return retval; +} + + +/* + * REVISIT: export at24_bin{read,write}() to let other kernel code use + * eeprom data. For example, it might hold a board's Ethernet address, or + * board-specific calibration data generated on the manufacturing floor. + */ + + +/* + * Note that if the hardware write-protect pin is pulled high, the whole + * chip is normally write protected. But there are plenty of product + * variants here, including OTP fuses and partial chip protect. + * + * We only use page mode writes; the alternative is sloooow. This routine + * writes at most one page. + */ +static ssize_t at24_eeprom_write(struct at24_data *at24, char *buf, + unsigned offset, size_t count) +{ + struct i2c_client *client; + struct i2c_msg msg; + ssize_t status; + unsigned long timeout, write_time; + unsigned next_page; + + /* Get corresponding I2C address and adjust offset */ + client = at24_translate_offset(at24, &offset); + + /* write_max is at most a page */ + if (count > at24->write_max) + count = at24->write_max; + + /* Never roll over backwards, to the start of this page */ + next_page = roundup(offset + 1, at24->chip.page_size); + if (offset + count > next_page) + count = next_page - offset; + + /* If we'll use I2C calls for I/O, set up the message */ + if (!at24->use_smbus) { + int i = 0; + + msg.addr = client->addr; + msg.flags = 0; + + /* msg.buf is u8 and casts will mask the values */ + msg.buf = at24->writebuf; + if (at24->chip.flags & AT24_FLAG_ADDR16) + msg.buf[i++] = offset >> 8; + + msg.buf[i++] = offset; + memcpy(&msg.buf[i], buf, count); + msg.len = i + count; + } + + /* + * Writes fail if the previous one didn't complete yet. We may + * loop a few times until this one succeeds, waiting at least + * long enough for one entire page write to work. + */ + timeout = jiffies + msecs_to_jiffies(write_timeout); + do { + write_time = jiffies; + if (at24->use_smbus) { + status = i2c_smbus_write_i2c_block_data(client, + offset, count, buf); + if (status == 0) + status = count; + } else { + status = i2c_transfer(client->adapter, &msg, 1); + if (status == 1) + status = count; + } + dev_dbg(&client->dev, "write %zu@%d --> %zd (%ld)\n", + count, offset, status, jiffies); + + if (status == count) + return count; + + /* REVISIT: at HZ=100, this is sloooow */ + msleep(1); + } while (time_before(write_time, timeout)); + + return -ETIMEDOUT; +} + +static ssize_t at24_bin_write(struct kobject *kobj, struct bin_attribute *attr, + char *buf, loff_t off, size_t count) +{ + struct at24_data *at24; + ssize_t retval = 0; + + at24 = dev_get_drvdata(container_of(kobj, struct device, kobj)); + + if (unlikely(!count)) + return count; + + /* + * Write data to chip, protecting against concurrent updates + * from this host, but not from other I2C masters. + */ + mutex_lock(&at24->lock); + + while (count) { + ssize_t status; + + status = at24_eeprom_write(at24, buf, off, count); + if (status <= 0) { + if (retval == 0) + retval = status; + break; + } + buf += status; + off += status; + count -= status; + retval += status; + } + + mutex_unlock(&at24->lock); + + return retval; +} + +/*-------------------------------------------------------------------------*/ + +static int at24_probe(struct i2c_client *client, const struct i2c_device_id *id) +{ + struct at24_platform_data chip; + bool writable; + bool use_smbus = false; + struct at24_data *at24; + int err; + unsigned i, num_addresses; + kernel_ulong_t magic; + + if (client->dev.platform_data) { + chip = *(struct at24_platform_data *)client->dev.platform_data; + } else { + if (!id->driver_data) { + err = -ENODEV; + goto err_out; + } + magic = id->driver_data; + chip.byte_len = BIT(magic & AT24_BITMASK(AT24_SIZE_BYTELEN)); + magic >>= AT24_SIZE_BYTELEN; + chip.flags = magic & AT24_BITMASK(AT24_SIZE_FLAGS); + /* + * This is slow, but we can't know all eeproms, so we better + * play safe. Specifying custom eeprom-types via platform_data + * is recommended anyhow. + */ + chip.page_size = 1; + } + + if (!is_power_of_2(chip.byte_len)) + dev_warn(&client->dev, + "byte_len looks suspicious (no power of 2)!\n"); + if (!is_power_of_2(chip.page_size)) + dev_warn(&client->dev, + "page_size looks suspicious (no power of 2)!\n"); + + /* Use I2C operations unless we're stuck with SMBus extensions. */ + if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) { + if (chip.flags & AT24_FLAG_ADDR16) { + err = -EPFNOSUPPORT; + goto err_out; + } + if (!i2c_check_functionality(client->adapter, + I2C_FUNC_SMBUS_READ_I2C_BLOCK)) { + err = -EPFNOSUPPORT; + goto err_out; + } + use_smbus = true; + } + + if (chip.flags & AT24_FLAG_TAKE8ADDR) + num_addresses = 8; + else + num_addresses = DIV_ROUND_UP(chip.byte_len, + (chip.flags & AT24_FLAG_ADDR16) ? 65536 : 256); + + at24 = kzalloc(sizeof(struct at24_data) + + num_addresses * sizeof(struct i2c_client *), GFP_KERNEL); + if (!at24) { + err = -ENOMEM; + goto err_out; + } + + mutex_init(&at24->lock); + at24->use_smbus = use_smbus; + at24->chip = chip; + at24->num_addresses = num_addresses; + + /* + * Export the EEPROM bytes through sysfs, since that's convenient. + * By default, only root should see the data (maybe passwords etc) + */ + at24->bin.attr.name = "eeprom"; + at24->bin.attr.mode = chip.flags & AT24_FLAG_IRUGO ? S_IRUGO : S_IRUSR; + at24->bin.read = at24_bin_read; + at24->bin.size = chip.byte_len; + + writable = !(chip.flags & AT24_FLAG_READONLY); + if (writable) { + if (!use_smbus || i2c_check_functionality(client->adapter, + I2C_FUNC_SMBUS_WRITE_I2C_BLOCK)) { + + unsigned write_max = chip.page_size; + + at24->bin.write = at24_bin_write; + at24->bin.attr.mode |= S_IWUSR; + + if (write_max > io_limit) + write_max = io_limit; + if (use_smbus && write_max > I2C_SMBUS_BLOCK_MAX) + write_max = I2C_SMBUS_BLOCK_MAX; + at24->write_max = write_max; + + /* buffer (data + address at the beginning) */ + at24->writebuf = kmalloc(write_max + 2, GFP_KERNEL); + if (!at24->writebuf) { + err = -ENOMEM; + goto err_struct; + } + } else { + dev_warn(&client->dev, + "cannot write due to controller restrictions."); + } + } + + at24->client[0] = client; + + /* use dummy devices for multiple-address chips */ + for (i = 1; i < num_addresses; i++) { + at24->client[i] = i2c_new_dummy(client->adapter, + client->addr + i); + if (!at24->client[i]) { + dev_err(&client->dev, "address 0x%02x unavailable\n", + client->addr + i); + err = -EADDRINUSE; + goto err_clients; + } + } + + err = sysfs_create_bin_file(&client->dev.kobj, &at24->bin); + if (err) + goto err_clients; + + i2c_set_clientdata(client, at24); + + dev_info(&client->dev, "%zu byte %s EEPROM %s\n", + at24->bin.size, client->name, + writable ? "(writable)" : "(read-only)"); + dev_dbg(&client->dev, + "page_size %d, num_addresses %d, write_max %d%s\n", + chip.page_size, num_addresses, + at24->write_max, + use_smbus ? ", use_smbus" : ""); + + return 0; + +err_clients: + for (i = 1; i < num_addresses; i++) + if (at24->client[i]) + i2c_unregister_device(at24->client[i]); + + kfree(at24->writebuf); +err_struct: + kfree(at24); +err_out: + dev_dbg(&client->dev, "probe error %d\n", err); + return err; +} + +static int __devexit at24_remove(struct i2c_client *client) +{ + struct at24_data *at24; + int i; + + at24 = i2c_get_clientdata(client); + sysfs_remove_bin_file(&client->dev.kobj, &at24->bin); + + for (i = 1; i < at24->num_addresses; i++) + i2c_unregister_device(at24->client[i]); + + kfree(at24->writebuf); + kfree(at24); + i2c_set_clientdata(client, NULL); + return 0; +} + +/*-------------------------------------------------------------------------*/ + +static struct i2c_driver at24_driver = { + .driver = { + .name = "at24", + .owner = THIS_MODULE, + }, + .probe = at24_probe, + .remove = __devexit_p(at24_remove), + .id_table = at24_ids, +}; + +static int __init at24_init(void) +{ + io_limit = rounddown_pow_of_two(io_limit); + return i2c_add_driver(&at24_driver); +} +module_init(at24_init); + +static void __exit at24_exit(void) +{ + i2c_del_driver(&at24_driver); +} +module_exit(at24_exit); + +MODULE_DESCRIPTION("Driver for most I2C EEPROMs"); +MODULE_AUTHOR("David Brownell and Wolfram Sang"); +MODULE_LICENSE("GPL"); diff --git a/drivers/misc/eeprom/at25.c b/drivers/misc/eeprom/at25.c new file mode 100644 index 00000000000..290dbe99647 --- /dev/null +++ b/drivers/misc/eeprom/at25.c @@ -0,0 +1,389 @@ +/* + * at25.c -- support most SPI EEPROMs, such as Atmel AT25 models + * + * Copyright (C) 2006 David Brownell + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/module.h> +#include <linux/slab.h> +#include <linux/delay.h> +#include <linux/device.h> +#include <linux/sched.h> + +#include <linux/spi/spi.h> +#include <linux/spi/eeprom.h> + + +/* + * NOTE: this is an *EEPROM* driver. The vagaries of product naming + * mean that some AT25 products are EEPROMs, and others are FLASH. + * Handle FLASH chips with the drivers/mtd/devices/m25p80.c driver, + * not this one! + */ + +struct at25_data { + struct spi_device *spi; + struct mutex lock; + struct spi_eeprom chip; + struct bin_attribute bin; + unsigned addrlen; +}; + +#define AT25_WREN 0x06 /* latch the write enable */ +#define AT25_WRDI 0x04 /* reset the write enable */ +#define AT25_RDSR 0x05 /* read status register */ +#define AT25_WRSR 0x01 /* write status register */ +#define AT25_READ 0x03 /* read byte(s) */ +#define AT25_WRITE 0x02 /* write byte(s)/sector */ + +#define AT25_SR_nRDY 0x01 /* nRDY = write-in-progress */ +#define AT25_SR_WEN 0x02 /* write enable (latched) */ +#define AT25_SR_BP0 0x04 /* BP for software writeprotect */ +#define AT25_SR_BP1 0x08 +#define AT25_SR_WPEN 0x80 /* writeprotect enable */ + + +#define EE_MAXADDRLEN 3 /* 24 bit addresses, up to 2 MBytes */ + +/* Specs often allow 5 msec for a page write, sometimes 20 msec; + * it's important to recover from write timeouts. + */ +#define EE_TIMEOUT 25 + +/*-------------------------------------------------------------------------*/ + +#define io_limit PAGE_SIZE /* bytes */ + +static ssize_t +at25_ee_read( + struct at25_data *at25, + char *buf, + unsigned offset, + size_t count +) +{ + u8 command[EE_MAXADDRLEN + 1]; + u8 *cp; + ssize_t status; + struct spi_transfer t[2]; + struct spi_message m; + + cp = command; + *cp++ = AT25_READ; + + /* 8/16/24-bit address is written MSB first */ + switch (at25->addrlen) { + default: /* case 3 */ + *cp++ = offset >> 16; + case 2: + *cp++ = offset >> 8; + case 1: + case 0: /* can't happen: for better codegen */ + *cp++ = offset >> 0; + } + + spi_message_init(&m); + memset(t, 0, sizeof t); + + t[0].tx_buf = command; + t[0].len = at25->addrlen + 1; + spi_message_add_tail(&t[0], &m); + + t[1].rx_buf = buf; + t[1].len = count; + spi_message_add_tail(&t[1], &m); + + mutex_lock(&at25->lock); + + /* Read it all at once. + * + * REVISIT that's potentially a problem with large chips, if + * other devices on the bus need to be accessed regularly or + * this chip is clocked very slowly + */ + status = spi_sync(at25->spi, &m); + dev_dbg(&at25->spi->dev, + "read %Zd bytes at %d --> %d\n", + count, offset, (int) status); + + mutex_unlock(&at25->lock); + return status ? status : count; +} + +static ssize_t +at25_bin_read(struct kobject *kobj, struct bin_attribute *bin_attr, + char *buf, loff_t off, size_t count) +{ + struct device *dev; + struct at25_data *at25; + + dev = container_of(kobj, struct device, kobj); + at25 = dev_get_drvdata(dev); + + if (unlikely(off >= at25->bin.size)) + return 0; + if ((off + count) > at25->bin.size) + count = at25->bin.size - off; + if (unlikely(!count)) + return count; + + return at25_ee_read(at25, buf, off, count); +} + + +static ssize_t +at25_ee_write(struct at25_data *at25, char *buf, loff_t off, size_t count) +{ + ssize_t status = 0; + unsigned written = 0; + unsigned buf_size; + u8 *bounce; + + /* Temp buffer starts with command and address */ + buf_size = at25->chip.page_size; + if (buf_size > io_limit) + buf_size = io_limit; + bounce = kmalloc(buf_size + at25->addrlen + 1, GFP_KERNEL); + if (!bounce) + return -ENOMEM; + + /* For write, rollover is within the page ... so we write at + * most one page, then manually roll over to the next page. + */ + bounce[0] = AT25_WRITE; + mutex_lock(&at25->lock); + do { + unsigned long timeout, retries; + unsigned segment; + unsigned offset = (unsigned) off; + u8 *cp = bounce + 1; + + *cp = AT25_WREN; + status = spi_write(at25->spi, cp, 1); + if (status < 0) { + dev_dbg(&at25->spi->dev, "WREN --> %d\n", + (int) status); + break; + } + + /* 8/16/24-bit address is written MSB first */ + switch (at25->addrlen) { + default: /* case 3 */ + *cp++ = offset >> 16; + case 2: + *cp++ = offset >> 8; + case 1: + case 0: /* can't happen: for better codegen */ + *cp++ = offset >> 0; + } + + /* Write as much of a page as we can */ + segment = buf_size - (offset % buf_size); + if (segment > count) + segment = count; + memcpy(cp, buf, segment); + status = spi_write(at25->spi, bounce, + segment + at25->addrlen + 1); + dev_dbg(&at25->spi->dev, + "write %u bytes at %u --> %d\n", + segment, offset, (int) status); + if (status < 0) + break; + + /* REVISIT this should detect (or prevent) failed writes + * to readonly sections of the EEPROM... + */ + + /* Wait for non-busy status */ + timeout = jiffies + msecs_to_jiffies(EE_TIMEOUT); + retries = 0; + do { + int sr; + + sr = spi_w8r8(at25->spi, AT25_RDSR); + if (sr < 0 || (sr & AT25_SR_nRDY)) { + dev_dbg(&at25->spi->dev, + "rdsr --> %d (%02x)\n", sr, sr); + /* at HZ=100, this is sloooow */ + msleep(1); + continue; + } + if (!(sr & AT25_SR_nRDY)) + break; + } while (retries++ < 3 || time_before_eq(jiffies, timeout)); + + if (time_after(jiffies, timeout)) { + dev_err(&at25->spi->dev, + "write %d bytes offset %d, " + "timeout after %u msecs\n", + segment, offset, + jiffies_to_msecs(jiffies - + (timeout - EE_TIMEOUT))); + status = -ETIMEDOUT; + break; + } + + off += segment; + buf += segment; + count -= segment; + written += segment; + + } while (count > 0); + + mutex_unlock(&at25->lock); + + kfree(bounce); + return written ? written : status; +} + +static ssize_t +at25_bin_write(struct kobject *kobj, struct bin_attribute *bin_attr, + char *buf, loff_t off, size_t count) +{ + struct device *dev; + struct at25_data *at25; + + dev = container_of(kobj, struct device, kobj); + at25 = dev_get_drvdata(dev); + + if (unlikely(off >= at25->bin.size)) + return -EFBIG; + if ((off + count) > at25->bin.size) + count = at25->bin.size - off; + if (unlikely(!count)) + return count; + + return at25_ee_write(at25, buf, off, count); +} + +/*-------------------------------------------------------------------------*/ + +static int at25_probe(struct spi_device *spi) +{ + struct at25_data *at25 = NULL; + const struct spi_eeprom *chip; + int err; + int sr; + int addrlen; + + /* Chip description */ + chip = spi->dev.platform_data; + if (!chip) { + dev_dbg(&spi->dev, "no chip description\n"); + err = -ENODEV; + goto fail; + } + + /* For now we only support 8/16/24 bit addressing */ + if (chip->flags & EE_ADDR1) + addrlen = 1; + else if (chip->flags & EE_ADDR2) + addrlen = 2; + else if (chip->flags & EE_ADDR3) + addrlen = 3; + else { + dev_dbg(&spi->dev, "unsupported address type\n"); + err = -EINVAL; + goto fail; + } + + /* Ping the chip ... the status register is pretty portable, + * unlike probing manufacturer IDs. We do expect that system + * firmware didn't write it in the past few milliseconds! + */ + sr = spi_w8r8(spi, AT25_RDSR); + if (sr < 0 || sr & AT25_SR_nRDY) { + dev_dbg(&spi->dev, "rdsr --> %d (%02x)\n", sr, sr); + err = -ENXIO; + goto fail; + } + + if (!(at25 = kzalloc(sizeof *at25, GFP_KERNEL))) { + err = -ENOMEM; + goto fail; + } + + mutex_init(&at25->lock); + at25->chip = *chip; + at25->spi = spi_dev_get(spi); + dev_set_drvdata(&spi->dev, at25); + at25->addrlen = addrlen; + + /* Export the EEPROM bytes through sysfs, since that's convenient. + * Default to root-only access to the data; EEPROMs often hold data + * that's sensitive for read and/or write, like ethernet addresses, + * security codes, board-specific manufacturing calibrations, etc. + */ + at25->bin.attr.name = "eeprom"; + at25->bin.attr.mode = S_IRUSR; + at25->bin.read = at25_bin_read; + + at25->bin.size = at25->chip.byte_len; + if (!(chip->flags & EE_READONLY)) { + at25->bin.write = at25_bin_write; + at25->bin.attr.mode |= S_IWUSR; + } + + err = sysfs_create_bin_file(&spi->dev.kobj, &at25->bin); + if (err) + goto fail; + + dev_info(&spi->dev, "%Zd %s %s eeprom%s, pagesize %u\n", + (at25->bin.size < 1024) + ? at25->bin.size + : (at25->bin.size / 1024), + (at25->bin.size < 1024) ? "Byte" : "KByte", + at25->chip.name, + (chip->flags & EE_READONLY) ? " (readonly)" : "", + at25->chip.page_size); + return 0; +fail: + dev_dbg(&spi->dev, "probe err %d\n", err); + kfree(at25); + return err; +} + +static int __devexit at25_remove(struct spi_device *spi) +{ + struct at25_data *at25; + + at25 = dev_get_drvdata(&spi->dev); + sysfs_remove_bin_file(&spi->dev.kobj, &at25->bin); + kfree(at25); + return 0; +} + +/*-------------------------------------------------------------------------*/ + +static struct spi_driver at25_driver = { + .driver = { + .name = "at25", + .owner = THIS_MODULE, + }, + .probe = at25_probe, + .remove = __devexit_p(at25_remove), +}; + +static int __init at25_init(void) +{ + return spi_register_driver(&at25_driver); +} +module_init(at25_init); + +static void __exit at25_exit(void) +{ + spi_unregister_driver(&at25_driver); +} +module_exit(at25_exit); + +MODULE_DESCRIPTION("Driver for most SPI EEPROMs"); +MODULE_AUTHOR("David Brownell"); +MODULE_LICENSE("GPL"); + diff --git a/drivers/misc/eeprom/eeprom.c b/drivers/misc/eeprom/eeprom.c new file mode 100644 index 00000000000..2c27193aeaa --- /dev/null +++ b/drivers/misc/eeprom/eeprom.c @@ -0,0 +1,257 @@ +/* + Copyright (C) 1998, 1999 Frodo Looijaard <frodol@dds.nl> and + Philip Edelbrock <phil@netroedge.com> + Copyright (C) 2003 Greg Kroah-Hartman <greg@kroah.com> + Copyright (C) 2003 IBM Corp. + Copyright (C) 2004 Jean Delvare <khali@linux-fr.org> + + This program is free software; you can redistribute it and/or modify + it under the terms of the GNU General Public License as published by + the Free Software Foundation; either version 2 of the License, or + (at your option) any later version. + + This program is distributed in the hope that it will be useful, + but WITHOUT ANY WARRANTY; without even the implied warranty of + MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + GNU General Public License for more details. + + You should have received a copy of the GNU General Public License + along with this program; if not, write to the Free Software + Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. +*/ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/module.h> +#include <linux/slab.h> +#include <linux/jiffies.h> +#include <linux/i2c.h> +#include <linux/mutex.h> + +/* Addresses to scan */ +static const unsigned short normal_i2c[] = { 0x50, 0x51, 0x52, 0x53, 0x54, + 0x55, 0x56, 0x57, I2C_CLIENT_END }; + +/* Insmod parameters */ +I2C_CLIENT_INSMOD_1(eeprom); + + +/* Size of EEPROM in bytes */ +#define EEPROM_SIZE 256 + +/* possible types of eeprom devices */ +enum eeprom_nature { + UNKNOWN, + VAIO, +}; + +/* Each client has this additional data */ +struct eeprom_data { + struct mutex update_lock; + u8 valid; /* bitfield, bit!=0 if slice is valid */ + unsigned long last_updated[8]; /* In jiffies, 8 slices */ + u8 data[EEPROM_SIZE]; /* Register values */ + enum eeprom_nature nature; +}; + + +static void eeprom_update_client(struct i2c_client *client, u8 slice) +{ + struct eeprom_data *data = i2c_get_clientdata(client); + int i; + + mutex_lock(&data->update_lock); + + if (!(data->valid & (1 << slice)) || + time_after(jiffies, data->last_updated[slice] + 300 * HZ)) { + dev_dbg(&client->dev, "Starting eeprom update, slice %u\n", slice); + + if (i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_READ_I2C_BLOCK)) { + for (i = slice << 5; i < (slice + 1) << 5; i += 32) + if (i2c_smbus_read_i2c_block_data(client, i, + 32, data->data + i) + != 32) + goto exit; + } else { + for (i = slice << 5; i < (slice + 1) << 5; i += 2) { + int word = i2c_smbus_read_word_data(client, i); + if (word < 0) + goto exit; + data->data[i] = word & 0xff; + data->data[i + 1] = word >> 8; + } + } + data->last_updated[slice] = jiffies; + data->valid |= (1 << slice); + } +exit: + mutex_unlock(&data->update_lock); +} + +static ssize_t eeprom_read(struct kobject *kobj, struct bin_attribute *bin_attr, + char *buf, loff_t off, size_t count) +{ + struct i2c_client *client = to_i2c_client(container_of(kobj, struct device, kobj)); + struct eeprom_data *data = i2c_get_clientdata(client); + u8 slice; + + if (off > EEPROM_SIZE) + return 0; + if (off + count > EEPROM_SIZE) + count = EEPROM_SIZE - off; + + /* Only refresh slices which contain requested bytes */ + for (slice = off >> 5; slice <= (off + count - 1) >> 5; slice++) + eeprom_update_client(client, slice); + + /* Hide Vaio private settings to regular users: + - BIOS passwords: bytes 0x00 to 0x0f + - UUID: bytes 0x10 to 0x1f + - Serial number: 0xc0 to 0xdf */ + if (data->nature == VAIO && !capable(CAP_SYS_ADMIN)) { + int i; + + for (i = 0; i < count; i++) { + if ((off + i <= 0x1f) || + (off + i >= 0xc0 && off + i <= 0xdf)) + buf[i] = 0; + else + buf[i] = data->data[off + i]; + } + } else { + memcpy(buf, &data->data[off], count); + } + + return count; +} + +static struct bin_attribute eeprom_attr = { + .attr = { + .name = "eeprom", + .mode = S_IRUGO, + }, + .size = EEPROM_SIZE, + .read = eeprom_read, +}; + +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int eeprom_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info) +{ + struct i2c_adapter *adapter = client->adapter; + + /* EDID EEPROMs are often 24C00 EEPROMs, which answer to all + addresses 0x50-0x57, but we only care about 0x50. So decline + attaching to addresses >= 0x51 on DDC buses */ + if (!(adapter->class & I2C_CLASS_SPD) && client->addr >= 0x51) + return -ENODEV; + + /* There are four ways we can read the EEPROM data: + (1) I2C block reads (faster, but unsupported by most adapters) + (2) Word reads (128% overhead) + (3) Consecutive byte reads (88% overhead, unsafe) + (4) Regular byte data reads (265% overhead) + The third and fourth methods are not implemented by this driver + because all known adapters support one of the first two. */ + if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_READ_WORD_DATA) + && !i2c_check_functionality(adapter, I2C_FUNC_SMBUS_READ_I2C_BLOCK)) + return -ENODEV; + + strlcpy(info->type, "eeprom", I2C_NAME_SIZE); + + return 0; +} + +static int eeprom_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct i2c_adapter *adapter = client->adapter; + struct eeprom_data *data; + int err; + + if (!(data = kzalloc(sizeof(struct eeprom_data), GFP_KERNEL))) { + err = -ENOMEM; + goto exit; + } + + memset(data->data, 0xff, EEPROM_SIZE); + i2c_set_clientdata(client, data); + mutex_init(&data->update_lock); + data->nature = UNKNOWN; + + /* Detect the Vaio nature of EEPROMs. + We use the "PCG-" or "VGN-" prefix as the signature. */ + if (client->addr == 0x57 + && i2c_check_functionality(adapter, I2C_FUNC_SMBUS_READ_BYTE_DATA)) { + char name[4]; + + name[0] = i2c_smbus_read_byte_data(client, 0x80); + name[1] = i2c_smbus_read_byte_data(client, 0x81); + name[2] = i2c_smbus_read_byte_data(client, 0x82); + name[3] = i2c_smbus_read_byte_data(client, 0x83); + + if (!memcmp(name, "PCG-", 4) || !memcmp(name, "VGN-", 4)) { + dev_info(&client->dev, "Vaio EEPROM detected, " + "enabling privacy protection\n"); + data->nature = VAIO; + } + } + + /* create the sysfs eeprom file */ + err = sysfs_create_bin_file(&client->dev.kobj, &eeprom_attr); + if (err) + goto exit_kfree; + + return 0; + +exit_kfree: + kfree(data); +exit: + return err; +} + +static int eeprom_remove(struct i2c_client *client) +{ + sysfs_remove_bin_file(&client->dev.kobj, &eeprom_attr); + kfree(i2c_get_clientdata(client)); + + return 0; +} + +static const struct i2c_device_id eeprom_id[] = { + { "eeprom", 0 }, + { } +}; + +static struct i2c_driver eeprom_driver = { + .driver = { + .name = "eeprom", + }, + .probe = eeprom_probe, + .remove = eeprom_remove, + .id_table = eeprom_id, + + .class = I2C_CLASS_DDC | I2C_CLASS_SPD, + .detect = eeprom_detect, + .address_data = &addr_data, +}; + +static int __init eeprom_init(void) +{ + return i2c_add_driver(&eeprom_driver); +} + +static void __exit eeprom_exit(void) +{ + i2c_del_driver(&eeprom_driver); +} + + +MODULE_AUTHOR("Frodo Looijaard <frodol@dds.nl> and " + "Philip Edelbrock <phil@netroedge.com> and " + "Greg Kroah-Hartman <greg@kroah.com>"); +MODULE_DESCRIPTION("I2C EEPROM driver"); +MODULE_LICENSE("GPL"); + +module_init(eeprom_init); +module_exit(eeprom_exit); diff --git a/drivers/misc/eeprom/eeprom_93cx6.c b/drivers/misc/eeprom/eeprom_93cx6.c new file mode 100644 index 00000000000..15b1780025c --- /dev/null +++ b/drivers/misc/eeprom/eeprom_93cx6.c @@ -0,0 +1,240 @@ +/* + Copyright (C) 2004 - 2006 rt2x00 SourceForge Project + <http://rt2x00.serialmonkey.com> + + This program is free software; you can redistribute it and/or modify + it under the terms of the GNU General Public License as published by + the Free Software Foundation; either version 2 of the License, or + (at your option) any later version. + + This program is distributed in the hope that it will be useful, + but WITHOUT ANY WARRANTY; without even the implied warranty of + MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + GNU General Public License for more details. + + You should have received a copy of the GNU General Public License + along with this program; if not, write to the + Free Software Foundation, Inc., + 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. + */ + +/* + Module: eeprom_93cx6 + Abstract: EEPROM reader routines for 93cx6 chipsets. + Supported chipsets: 93c46 & 93c66. + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/delay.h> +#include <linux/eeprom_93cx6.h> + +MODULE_AUTHOR("http://rt2x00.serialmonkey.com"); +MODULE_VERSION("1.0"); +MODULE_DESCRIPTION("EEPROM 93cx6 chip driver"); +MODULE_LICENSE("GPL"); + +static inline void eeprom_93cx6_pulse_high(struct eeprom_93cx6 *eeprom) +{ + eeprom->reg_data_clock = 1; + eeprom->register_write(eeprom); + + /* + * Add a short delay for the pulse to work. + * According to the specifications the "maximum minimum" + * time should be 450ns. + */ + ndelay(450); +} + +static inline void eeprom_93cx6_pulse_low(struct eeprom_93cx6 *eeprom) +{ + eeprom->reg_data_clock = 0; + eeprom->register_write(eeprom); + + /* + * Add a short delay for the pulse to work. + * According to the specifications the "maximum minimum" + * time should be 450ns. + */ + ndelay(450); +} + +static void eeprom_93cx6_startup(struct eeprom_93cx6 *eeprom) +{ + /* + * Clear all flags, and enable chip select. + */ + eeprom->register_read(eeprom); + eeprom->reg_data_in = 0; + eeprom->reg_data_out = 0; + eeprom->reg_data_clock = 0; + eeprom->reg_chip_select = 1; + eeprom->register_write(eeprom); + + /* + * kick a pulse. + */ + eeprom_93cx6_pulse_high(eeprom); + eeprom_93cx6_pulse_low(eeprom); +} + +static void eeprom_93cx6_cleanup(struct eeprom_93cx6 *eeprom) +{ + /* + * Clear chip_select and data_in flags. + */ + eeprom->register_read(eeprom); + eeprom->reg_data_in = 0; + eeprom->reg_chip_select = 0; + eeprom->register_write(eeprom); + + /* + * kick a pulse. + */ + eeprom_93cx6_pulse_high(eeprom); + eeprom_93cx6_pulse_low(eeprom); +} + +static void eeprom_93cx6_write_bits(struct eeprom_93cx6 *eeprom, + const u16 data, const u16 count) +{ + unsigned int i; + + eeprom->register_read(eeprom); + + /* + * Clear data flags. + */ + eeprom->reg_data_in = 0; + eeprom->reg_data_out = 0; + + /* + * Start writing all bits. + */ + for (i = count; i > 0; i--) { + /* + * Check if this bit needs to be set. + */ + eeprom->reg_data_in = !!(data & (1 << (i - 1))); + + /* + * Write the bit to the eeprom register. + */ + eeprom->register_write(eeprom); + + /* + * Kick a pulse. + */ + eeprom_93cx6_pulse_high(eeprom); + eeprom_93cx6_pulse_low(eeprom); + } + + eeprom->reg_data_in = 0; + eeprom->register_write(eeprom); +} + +static void eeprom_93cx6_read_bits(struct eeprom_93cx6 *eeprom, + u16 *data, const u16 count) +{ + unsigned int i; + u16 buf = 0; + + eeprom->register_read(eeprom); + + /* + * Clear data flags. + */ + eeprom->reg_data_in = 0; + eeprom->reg_data_out = 0; + + /* + * Start reading all bits. + */ + for (i = count; i > 0; i--) { + eeprom_93cx6_pulse_high(eeprom); + + eeprom->register_read(eeprom); + + /* + * Clear data_in flag. + */ + eeprom->reg_data_in = 0; + + /* + * Read if the bit has been set. + */ + if (eeprom->reg_data_out) + buf |= (1 << (i - 1)); + + eeprom_93cx6_pulse_low(eeprom); + } + + *data = buf; +} + +/** + * eeprom_93cx6_read - Read multiple words from eeprom + * @eeprom: Pointer to eeprom structure + * @word: Word index from where we should start reading + * @data: target pointer where the information will have to be stored + * + * This function will read the eeprom data as host-endian word + * into the given data pointer. + */ +void eeprom_93cx6_read(struct eeprom_93cx6 *eeprom, const u8 word, + u16 *data) +{ + u16 command; + + /* + * Initialize the eeprom register + */ + eeprom_93cx6_startup(eeprom); + + /* + * Select the read opcode and the word to be read. + */ + command = (PCI_EEPROM_READ_OPCODE << eeprom->width) | word; + eeprom_93cx6_write_bits(eeprom, command, + PCI_EEPROM_WIDTH_OPCODE + eeprom->width); + + /* + * Read the requested 16 bits. + */ + eeprom_93cx6_read_bits(eeprom, data, 16); + + /* + * Cleanup eeprom register. + */ + eeprom_93cx6_cleanup(eeprom); +} +EXPORT_SYMBOL_GPL(eeprom_93cx6_read); + +/** + * eeprom_93cx6_multiread - Read multiple words from eeprom + * @eeprom: Pointer to eeprom structure + * @word: Word index from where we should start reading + * @data: target pointer where the information will have to be stored + * @words: Number of words that should be read. + * + * This function will read all requested words from the eeprom, + * this is done by calling eeprom_93cx6_read() multiple times. + * But with the additional change that while the eeprom_93cx6_read + * will return host ordered bytes, this method will return little + * endian words. + */ +void eeprom_93cx6_multiread(struct eeprom_93cx6 *eeprom, const u8 word, + __le16 *data, const u16 words) +{ + unsigned int i; + u16 tmp; + + for (i = 0; i < words; i++) { + tmp = 0; + eeprom_93cx6_read(eeprom, word + i, &tmp); + data[i] = cpu_to_le16(tmp); + } +} +EXPORT_SYMBOL_GPL(eeprom_93cx6_multiread); + |