diff options
Diffstat (limited to 'drivers/net/Kconfig')
| -rw-r--r-- | drivers/net/Kconfig | 74 |
1 files changed, 74 insertions, 0 deletions
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index 39189903e35..6f388d9e9be 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -1411,6 +1411,22 @@ config FORCEDETH <file:Documentation/networking/net-modules.txt>. The module will be called forcedeth. +config FORCEDETH_NAPI + bool "Use Rx and Tx Polling (NAPI) (EXPERIMENTAL)" + depends on FORCEDETH && EXPERIMENTAL + help + NAPI is a new driver API designed to reduce CPU and interrupt load + when the driver is receiving lots of packets from the card. It is + still somewhat experimental and thus not yet enabled by default. + + If your estimated Rx load is 10kpps or more, or if the card will be + deployed on potentially unfriendly networks (e.g. in a firewall), + then say Y here. + + See <file:Documentation/networking/NAPI_HOWTO.txt> for more + information. + + If in doubt, say N. config CS89x0 tristate "CS89x0 support" @@ -1724,6 +1740,20 @@ config VIA_RHINE_MMIO If unsure, say Y. +config VIA_RHINE_NAPI + bool "Use Rx Polling (NAPI)" + depends on VIA_RHINE + help + NAPI is a new driver API designed to reduce CPU and interrupt load + when the driver is receiving lots of packets from the card. + + If your estimated Rx load is 10kpps or more, or if the card will be + deployed on potentially unfriendly networks (e.g. in a firewall), + then say Y here. + + See <file:Documentation/networking/NAPI_HOWTO.txt> for more + information. + config LAN_SAA9730 bool "Philips SAA9730 Ethernet support (EXPERIMENTAL)" depends on NET_PCI && EXPERIMENTAL && MIPS @@ -2219,6 +2249,33 @@ config GFAR_NAPI bool "NAPI Support" depends on GIANFAR +config UCC_GETH + tristate "Freescale QE UCC GETH" + depends on QUICC_ENGINE && UCC_FAST + help + This driver supports the Gigabit Ethernet mode of QE UCC. + QE can be found on MPC836x CPUs. + +config UGETH_NAPI + bool "NAPI Support" + depends on UCC_GETH + +config UGETH_MAGIC_PACKET + bool "Magic Packet detection support" + depends on UCC_GETH + +config UGETH_FILTERING + bool "Mac address filtering support" + depends on UCC_GETH + +config UGETH_TX_ON_DEMOND + bool "Transmit on Demond support" + depends on UCC_GETH + +config UGETH_HAS_GIGA + bool + depends on UCC_GETH && MPC836x + config MV643XX_ETH tristate "MV-643XX Ethernet support" depends on MOMENCO_OCELOT_C || MOMENCO_JAGUAR_ATX || MV64360 || MOMENCO_OCELOT_3 || PPC_MULTIPLATFORM @@ -2249,6 +2306,15 @@ config MV643XX_ETH_2 This enables support for Port 2 of the Marvell MV643XX Gigabit Ethernet. +config QLA3XXX + tristate "QLogic QLA3XXX Network Driver Support" + depends on PCI + help + This driver supports QLogic ISP3XXX gigabit Ethernet cards. + + To compile this driver as a module, choose M here: the module + will be called qla3xxx. + endmenu # @@ -2509,6 +2575,7 @@ config PLIP config PPP tristate "PPP (point-to-point protocol) support" + select SLHC ---help--- PPP (Point to Point Protocol) is a newer and better SLIP. It serves the same purpose: sending Internet traffic over telephone (and other @@ -2689,6 +2756,7 @@ config SLIP config SLIP_COMPRESSED bool "CSLIP compressed headers" depends on SLIP + select SLHC ---help--- This protocol is faster than SLIP because it uses compression on the TCP/IP headers (not on the data itself), but it has to be supported @@ -2701,6 +2769,12 @@ config SLIP_COMPRESSED <http://www.tldp.org/docs.html#howto>, explains how to configure CSLIP. This won't enlarge your kernel. +config SLHC + tristate + help + This option enables Van Jacobsen serial line header compression + routines. + config SLIP_SMART bool "Keepalive and linefill" depends on SLIP |