aboutsummaryrefslogtreecommitdiff
path: root/drivers/net/wireless/ath/ath5k/reset.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net/wireless/ath/ath5k/reset.c')
-rw-r--r--drivers/net/wireless/ath/ath5k/reset.c33
1 files changed, 11 insertions, 22 deletions
diff --git a/drivers/net/wireless/ath/ath5k/reset.c b/drivers/net/wireless/ath/ath5k/reset.c
index 34e13c70084..62954fc7786 100644
--- a/drivers/net/wireless/ath/ath5k/reset.c
+++ b/drivers/net/wireless/ath/ath5k/reset.c
@@ -25,6 +25,8 @@
Reset functions and helpers
\*****************************/
+#include <asm/unaligned.h>
+
#include <linux/pci.h> /* To determine if a card is pci-e */
#include <linux/log2.h>
#include "ath5k.h"
@@ -870,6 +872,7 @@ static void ath5k_hw_commit_eeprom_settings(struct ath5k_hw *ah,
int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode,
struct ieee80211_channel *channel, bool change_channel)
{
+ struct ath_common *common = ath5k_hw_common(ah);
u32 s_seq[10], s_ant, s_led[3], staid1_flags, tsf_up, tsf_lo;
u32 phy_tst1;
u8 mode, freq, ee_mode, ant[2];
@@ -1171,10 +1174,12 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode,
ath5k_hw_reg_write(ah, s_led[2], AR5K_GPIODO);
/* Restore sta_id flags and preserve our mac address*/
- ath5k_hw_reg_write(ah, AR5K_LOW_ID(ah->ah_sta_id),
- AR5K_STA_ID0);
- ath5k_hw_reg_write(ah, staid1_flags | AR5K_HIGH_ID(ah->ah_sta_id),
- AR5K_STA_ID1);
+ ath5k_hw_reg_write(ah,
+ get_unaligned_le32(common->macaddr),
+ AR5K_STA_ID0);
+ ath5k_hw_reg_write(ah,
+ staid1_flags | get_unaligned_le16(common->macaddr + 4),
+ AR5K_STA_ID1);
/*
@@ -1182,8 +1187,7 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode,
*/
/* Restore bssid and bssid mask */
- /* XXX: add ah->aid once mac80211 gives this to us */
- ath5k_hw_set_associd(ah, ah->ah_bssid, 0);
+ ath5k_hw_set_associd(ah);
/* Set PCU config */
ath5k_hw_set_opmode(ah);
@@ -1289,7 +1293,7 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode,
* out and/or noise floor calibration might timeout.
*/
AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_AGCCTL,
- AR5K_PHY_AGCCTL_CAL);
+ AR5K_PHY_AGCCTL_CAL | AR5K_PHY_AGCCTL_NF);
/* At the same time start I/Q calibration for QAM constellation
* -no need for CCK- */
@@ -1310,21 +1314,6 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode,
channel->center_freq);
}
- /*
- * If we run NF calibration before AGC, it always times out.
- * Binary HAL starts NF and AGC calibration at the same time
- * and only waits for AGC to finish. Also if AGC or NF cal.
- * times out, reset doesn't fail on binary HAL. I believe
- * that's wrong because since rx path is routed to a detector,
- * if cal. doesn't finish we won't have RX. Sam's HAL for AR5210/5211
- * enables noise floor calibration after offset calibration and if noise
- * floor calibration fails, reset fails. I believe that's
- * a better approach, we just need to find a polling interval
- * that suits best, even if reset continues we need to make
- * sure that rx path is ready.
- */
- ath5k_hw_noise_floor_calibration(ah, channel->center_freq);
-
/* Restore antenna mode */
ath5k_hw_set_antenna_mode(ah, ah->ah_ant_mode);