diff options
Diffstat (limited to 'drivers/net/wireless/b43')
-rw-r--r-- | drivers/net/wireless/b43/b43.h | 15 | ||||
-rw-r--r-- | drivers/net/wireless/b43/main.c | 248 |
2 files changed, 136 insertions, 127 deletions
diff --git a/drivers/net/wireless/b43/b43.h b/drivers/net/wireless/b43/b43.h index a22435ade8c..2c8fa1c3465 100644 --- a/drivers/net/wireless/b43/b43.h +++ b/drivers/net/wireless/b43/b43.h @@ -604,9 +604,8 @@ struct b43_wl { * at a time. General information about this interface follows. */ - /* Opaque ID of the operating interface (!= monitor - * interface) from the ieee80211 subsystem. - * Do not modify. + /* Opaque ID of the operating interface from the ieee80211 + * subsystem. Do not modify. */ int if_id; /* The MAC address of the operating interface. */ @@ -615,14 +614,10 @@ struct b43_wl { u8 bssid[ETH_ALEN]; /* Interface type. (IEEE80211_IF_TYPE_XXX) */ int if_type; - /* Counter of active monitor interfaces. */ - int monitor; /* Is the card operating in AP, STA or IBSS mode? */ bool operating; - /* Promisc mode active? - * Note that (monitor != 0) implies promisc. - */ - bool promisc; + /* filter flags */ + unsigned int filter_flags; /* Stats about the wireless interface */ struct ieee80211_low_level_stats ieee_stats; @@ -779,8 +774,6 @@ static inline struct b43_wldev *dev_to_b43_wldev(struct device *dev) /* Is the device operating in a specified mode (IEEE80211_IF_TYPE_XXX). */ static inline int b43_is_mode(struct b43_wl *wl, int type) { - if (type == IEEE80211_IF_TYPE_MNTR) - return !!(wl->monitor); return (wl->operating && wl->if_type == type); } diff --git a/drivers/net/wireless/b43/main.c b/drivers/net/wireless/b43/main.c index b44c9f92884..72467c86f8d 100644 --- a/drivers/net/wireless/b43/main.c +++ b/drivers/net/wireless/b43/main.c @@ -92,14 +92,6 @@ static char modparam_fwpostfix[16]; module_param_string(fwpostfix, modparam_fwpostfix, 16, 0444); MODULE_PARM_DESC(fwpostfix, "Postfix for the .fw files to load."); -static int modparam_mon_keep_bad; -module_param_named(mon_keep_bad, modparam_mon_keep_bad, int, 0444); -MODULE_PARM_DESC(mon_keep_bad, "Keep bad frames in monitor mode"); - -static int modparam_mon_keep_badplcp; -module_param_named(mon_keep_badplcp, modparam_mon_keep_bad, int, 0444); -MODULE_PARM_DESC(mon_keep_badplcp, "Keep frames with bad PLCP in monitor mode"); - static int modparam_hwpctl; module_param_named(hwpctl, modparam_hwpctl, int, 0444); MODULE_PARM_DESC(hwpctl, "Enable hardware-side power control (default off)"); @@ -561,15 +553,10 @@ static void b43_write_mac_bssid_templates(struct b43_wldev *dev) } } -static void b43_upload_card_macaddress(struct b43_wldev *dev, - const u8 * mac_addr) +static void b43_upload_card_macaddress(struct b43_wldev *dev) { - if (mac_addr) - memcpy(dev->wl->mac_addr, mac_addr, ETH_ALEN); - else - memset(dev->wl->mac_addr, 0, ETH_ALEN); b43_write_mac_bssid_templates(dev); - b43_macfilter_set(dev, B43_MACFILTER_SELF, mac_addr); + b43_macfilter_set(dev, B43_MACFILTER_SELF, dev->wl->mac_addr); } static void b43_set_slot_time(struct b43_wldev *dev, u16 slot_time) @@ -2052,33 +2039,25 @@ static void b43_adjust_opmode(struct b43_wldev *dev) ctl &= ~B43_MACCTL_KEEP_BADPLCP; ctl &= ~B43_MACCTL_KEEP_BAD; ctl &= ~B43_MACCTL_PROMISC; + ctl &= ~B43_MACCTL_BEACPROMISC; ctl |= B43_MACCTL_INFRA; - if (wl->operating) { - switch (wl->if_type) { - case IEEE80211_IF_TYPE_AP: - ctl |= B43_MACCTL_AP; - break; - case IEEE80211_IF_TYPE_IBSS: - ctl &= ~B43_MACCTL_INFRA; - break; - case IEEE80211_IF_TYPE_STA: - case IEEE80211_IF_TYPE_MNTR: - case IEEE80211_IF_TYPE_WDS: - break; - default: - B43_WARN_ON(1); - } - } - if (wl->monitor) { + if (b43_is_mode(wl, IEEE80211_IF_TYPE_AP)) + ctl |= B43_MACCTL_AP; + else if (b43_is_mode(wl, IEEE80211_IF_TYPE_IBSS)) + ctl &= ~B43_MACCTL_INFRA; + + if (wl->filter_flags & FIF_CONTROL) ctl |= B43_MACCTL_KEEP_CTL; - if (modparam_mon_keep_bad) - ctl |= B43_MACCTL_KEEP_BAD; - if (modparam_mon_keep_badplcp) - ctl |= B43_MACCTL_KEEP_BADPLCP; - } - if (wl->promisc) + if (wl->filter_flags & FIF_FCSFAIL) + ctl |= B43_MACCTL_KEEP_BAD; + if (wl->filter_flags & FIF_PLCPFAIL) + ctl |= B43_MACCTL_KEEP_BADPLCP; + if (wl->filter_flags & FIF_PROMISC_IN_BSS) ctl |= B43_MACCTL_PROMISC; + if (wl->filter_flags & FIF_BCN_PRBRESP_PROMISC) + ctl |= B43_MACCTL_BEACPROMISC; + /* Workaround: On old hardware the HW-MAC-address-filter * doesn't work properly, so always run promisc in filter * it in software. */ @@ -2254,9 +2233,6 @@ static int b43_chip_init(struct b43_wldev *dev) & ~B43_MACCTL_INFRA); b43_write32(dev, B43_MMIO_MACCTL, b43_read32(dev, B43_MMIO_MACCTL) | B43_MACCTL_INFRA); - /* Let beacons come through */ - b43_write32(dev, B43_MMIO_MACCTL, b43_read32(dev, B43_MMIO_MACCTL) - | B43_MACCTL_BEACPROMISC); if (b43_using_pio(dev)) { b43_write32(dev, 0x0210, 0x00000100); @@ -2899,9 +2875,9 @@ static int b43_dev_config(struct ieee80211_hw *hw, struct ieee80211_conf *conf) return err; } -static int b43_dev_set_key(struct ieee80211_hw *hw, - set_key_cmd cmd, const u8 *local_addr, - const u8 *addr, struct ieee80211_key_conf *key) +static int b43_dev_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd, + const u8 *local_addr, const u8 *addr, + struct ieee80211_key_conf *key) { struct b43_wl *wl = hw_to_b43_wl(hw); struct b43_wldev *dev = wl->current_dev; @@ -3003,21 +2979,40 @@ out: return err; } -static void b43_set_multicast_list(struct ieee80211_hw *hw, - unsigned short netflags, int mc_count) +static void b43_configure_filter(struct ieee80211_hw *hw, + unsigned int changed, unsigned int *fflags, + int mc_count, struct dev_addr_list *mc_list) { struct b43_wl *wl = hw_to_b43_wl(hw); struct b43_wldev *dev = wl->current_dev; unsigned long flags; - if (!dev) + if (!dev) { + *fflags = 0; return; - spin_lock_irqsave(&wl->irq_lock, flags); - if (wl->promisc != !!(netflags & IFF_PROMISC)) { - wl->promisc = !!(netflags & IFF_PROMISC); - if (b43_status(dev) >= B43_STAT_INITIALIZED) - b43_adjust_opmode(dev); } + + spin_lock_irqsave(&wl->irq_lock, flags); + *fflags &= FIF_PROMISC_IN_BSS | + FIF_ALLMULTI | + FIF_FCSFAIL | + FIF_PLCPFAIL | + FIF_CONTROL | + FIF_OTHER_BSS | + FIF_BCN_PRBRESP_PROMISC; + + changed &= FIF_PROMISC_IN_BSS | + FIF_ALLMULTI | + FIF_FCSFAIL | + FIF_PLCPFAIL | + FIF_CONTROL | + FIF_OTHER_BSS | + FIF_BCN_PRBRESP_PROMISC; + + wl->filter_flags = *fflags; + + if (changed && b43_status(dev) >= B43_STAT_INITIALIZED) + b43_adjust_opmode(dev); spin_unlock_irqrestore(&wl->irq_lock, flags); } @@ -3032,21 +3027,19 @@ static int b43_config_interface(struct ieee80211_hw *hw, return -ENODEV; mutex_lock(&wl->mutex); spin_lock_irqsave(&wl->irq_lock, flags); - if (conf->type != IEEE80211_IF_TYPE_MNTR) { - B43_WARN_ON(wl->if_id != if_id); - if (conf->bssid) - memcpy(wl->bssid, conf->bssid, ETH_ALEN); - else - memset(wl->bssid, 0, ETH_ALEN); - if (b43_status(dev) >= B43_STAT_INITIALIZED) { - if (b43_is_mode(wl, IEEE80211_IF_TYPE_AP)) { - B43_WARN_ON(conf->type != IEEE80211_IF_TYPE_AP); - b43_set_ssid(dev, conf->ssid, conf->ssid_len); - if (conf->beacon) - b43_refresh_templates(dev, conf->beacon); - } - b43_write_mac_bssid_templates(dev); + B43_WARN_ON(wl->if_id != if_id); + if (conf->bssid) + memcpy(wl->bssid, conf->bssid, ETH_ALEN); + else + memset(wl->bssid, 0, ETH_ALEN); + if (b43_status(dev) >= B43_STAT_INITIALIZED) { + if (b43_is_mode(wl, IEEE80211_IF_TYPE_AP)) { + B43_WARN_ON(conf->type != IEEE80211_IF_TYPE_AP); + b43_set_ssid(dev, conf->ssid, conf->ssid_len); + if (conf->beacon) + b43_refresh_templates(dev, conf->beacon); } + b43_write_mac_bssid_templates(dev); } spin_unlock_irqrestore(&wl->irq_lock, flags); mutex_unlock(&wl->mutex); @@ -3472,7 +3465,8 @@ static int b43_wireless_core_init(struct b43_wldev *dev) ssb_bus_powerup(bus, 1); /* Enable dynamic PCTL */ memset(wl->bssid, 0, ETH_ALEN); - b43_upload_card_macaddress(dev, NULL); + memset(wl->mac_addr, 0, ETH_ALEN); + b43_upload_card_macaddress(dev); b43_security_init(dev); b43_rng_init(wl); @@ -3502,21 +3496,80 @@ static int b43_add_interface(struct ieee80211_hw *hw, struct b43_wldev *dev; unsigned long flags; int err = -EOPNOTSUPP; - int did_init = 0; + + /* TODO: allow WDS/AP devices to coexist */ + + if (conf->type != IEEE80211_IF_TYPE_AP && + conf->type != IEEE80211_IF_TYPE_STA && + conf->type != IEEE80211_IF_TYPE_WDS && + conf->type != IEEE80211_IF_TYPE_IBSS) + return -EOPNOTSUPP; mutex_lock(&wl->mutex); - if ((conf->type != IEEE80211_IF_TYPE_MNTR) && wl->operating) + if (wl->operating) goto out_mutex_unlock; b43dbg(wl, "Adding Interface type %d\n", conf->type); dev = wl->current_dev; + wl->operating = 1; + wl->if_id = conf->if_id; + wl->if_type = conf->type; + memcpy(wl->mac_addr, conf->mac_addr, ETH_ALEN); + + spin_lock_irqsave(&wl->irq_lock, flags); + b43_adjust_opmode(dev); + b43_upload_card_macaddress(dev); + spin_unlock_irqrestore(&wl->irq_lock, flags); + + err = 0; + out_mutex_unlock: + mutex_unlock(&wl->mutex); + + return err; +} + +static void b43_remove_interface(struct ieee80211_hw *hw, + struct ieee80211_if_init_conf *conf) +{ + struct b43_wl *wl = hw_to_b43_wl(hw); + struct b43_wldev *dev = wl->current_dev; + unsigned long flags; + + b43dbg(wl, "Removing Interface type %d\n", conf->type); + + mutex_lock(&wl->mutex); + + B43_WARN_ON(!wl->operating); + B43_WARN_ON(wl->if_id != conf->if_id); + + wl->operating = 0; + + spin_lock_irqsave(&wl->irq_lock, flags); + b43_adjust_opmode(dev); + memset(wl->mac_addr, 0, ETH_ALEN); + b43_upload_card_macaddress(dev); + spin_unlock_irqrestore(&wl->irq_lock, flags); + + mutex_unlock(&wl->mutex); +} + +static int b43_start(struct ieee80211_hw *hw) +{ + struct b43_wl *wl = hw_to_b43_wl(hw); + struct b43_wldev *dev = wl->current_dev; + int did_init = 0; + int err; + + mutex_lock(&wl->mutex); + if (b43_status(dev) < B43_STAT_INITIALIZED) { err = b43_wireless_core_init(dev); if (err) goto out_mutex_unlock; did_init = 1; } + if (b43_status(dev) < B43_STAT_STARTED) { err = b43_wireless_core_start(dev); if (err) { @@ -3526,59 +3579,21 @@ static int b43_add_interface(struct ieee80211_hw *hw, } } - spin_lock_irqsave(&wl->irq_lock, flags); - switch (conf->type) { - case IEEE80211_IF_TYPE_MNTR: - wl->monitor++; - break; - default: - wl->operating = 1; - wl->if_id = conf->if_id; - wl->if_type = conf->type; - b43_upload_card_macaddress(dev, conf->mac_addr); - } - b43_adjust_opmode(dev); - spin_unlock_irqrestore(&wl->irq_lock, flags); - - err = 0; - out_mutex_unlock: + out_mutex_unlock: mutex_unlock(&wl->mutex); return err; } -static void b43_remove_interface(struct ieee80211_hw *hw, - struct ieee80211_if_init_conf *conf) +void b43_stop(struct ieee80211_hw *hw) { struct b43_wl *wl = hw_to_b43_wl(hw); - struct b43_wldev *dev; - unsigned long flags; - - b43dbg(wl, "Removing Interface type %d\n", conf->type); + struct b43_wldev *dev = wl->current_dev; mutex_lock(&wl->mutex); - if (conf->type == IEEE80211_IF_TYPE_MNTR) { - wl->monitor--; - B43_WARN_ON(wl->monitor < 0); - } else { - B43_WARN_ON(!wl->operating); - wl->operating = 0; - } - - dev = wl->current_dev; - if (!wl->operating && wl->monitor == 0) { - /* No interface left. */ - if (b43_status(dev) >= B43_STAT_STARTED) - b43_wireless_core_stop(dev); - b43_wireless_core_exit(dev); - } else { - /* Just monitor interfaces left. */ - spin_lock_irqsave(&wl->irq_lock, flags); - b43_adjust_opmode(dev); - if (!wl->operating) - b43_upload_card_macaddress(dev, NULL); - spin_unlock_irqrestore(&wl->irq_lock, flags); - } + if (b43_status(dev) >= B43_STAT_STARTED) + b43_wireless_core_stop(dev); + b43_wireless_core_exit(dev); mutex_unlock(&wl->mutex); } @@ -3589,10 +3604,12 @@ static const struct ieee80211_ops b43_hw_ops = { .remove_interface = b43_remove_interface, .config = b43_dev_config, .config_interface = b43_config_interface, - .set_multicast_list = b43_set_multicast_list, + .configure_filter = b43_configure_filter, .set_key = b43_dev_set_key, .get_stats = b43_get_stats, .get_tx_stats = b43_get_tx_stats, + .start = b43_start, + .stop = b43_stop, }; /* Hard-reset the chip. Do not call this directly. @@ -3930,8 +3947,7 @@ static int b43_wireless_init(struct ssb_device *dev) } /* fill hw info */ - hw->flags = IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE | - IEEE80211_HW_MONITOR_DURING_OPER; + hw->flags = IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE; hw->max_signal = 100; hw->max_rssi = -110; hw->max_noise = -110; |