diff options
Diffstat (limited to 'drivers/net/wireless/iwlwifi')
| -rw-r--r-- | drivers/net/wireless/iwlwifi/iwl-3945-hw.h | 135 | ||||
| -rw-r--r-- | drivers/net/wireless/iwlwifi/iwl-3945.c | 18 | ||||
| -rw-r--r-- | drivers/net/wireless/iwlwifi/iwl-3945.h | 3 | ||||
| -rw-r--r-- | drivers/net/wireless/iwlwifi/iwl-4965-hw.h | 131 | ||||
| -rw-r--r-- | drivers/net/wireless/iwlwifi/iwl-4965.c | 6 | ||||
| -rw-r--r-- | drivers/net/wireless/iwlwifi/iwl-4965.h | 1 | ||||
| -rw-r--r-- | drivers/net/wireless/iwlwifi/iwl-csr.h | 217 | ||||
| -rw-r--r-- | drivers/net/wireless/iwlwifi/iwl3945-base.c | 4 | ||||
| -rw-r--r-- | drivers/net/wireless/iwlwifi/iwl4965-base.c | 4 |
9 files changed, 236 insertions, 283 deletions
diff --git a/drivers/net/wireless/iwlwifi/iwl-3945-hw.h b/drivers/net/wireless/iwlwifi/iwl-3945-hw.h index 6693767adc9..269224ba23b 100644 --- a/drivers/net/wireless/iwlwifi/iwl-3945-hw.h +++ b/drivers/net/wireless/iwlwifi/iwl-3945-hw.h @@ -321,141 +321,6 @@ struct iwl3945_eeprom { #define PCI_REG_WUM8 0x0E8 #define PCI_CFG_PMC_PME_FROM_D3COLD_SUPPORT (0x80000000) -/*=== CSR (control and status registers) ===*/ -#define CSR_BASE (0x000) - -#define CSR_HW_IF_CONFIG_REG (CSR_BASE+0x000) /* hardware interface config */ -#define CSR_INT_COALESCING (CSR_BASE+0x004) /* accum ints, 32-usec units */ -#define CSR_INT (CSR_BASE+0x008) /* host interrupt status/ack */ -#define CSR_INT_MASK (CSR_BASE+0x00c) /* host interrupt enable */ -#define CSR_FH_INT_STATUS (CSR_BASE+0x010) /* busmaster int status/ack*/ -#define CSR_GPIO_IN (CSR_BASE+0x018) /* read external chip pins */ -#define CSR_RESET (CSR_BASE+0x020) /* busmaster enable, NMI, etc*/ -#define CSR_GP_CNTRL (CSR_BASE+0x024) - -/* - * Hardware revision info - * Bit fields: - * 31-8: Reserved - * 7-4: Type of device: 0x0 = 4965, 0xd = 3945 - * 3-2: Revision step: 0 = A, 1 = B, 2 = C, 3 = D - * 1-0: "Dash" value, as in A-1, etc. - */ -#define CSR_HW_REV (CSR_BASE+0x028) - -/* EEPROM reads */ -#define CSR_EEPROM_REG (CSR_BASE+0x02c) -#define CSR_EEPROM_GP (CSR_BASE+0x030) -#define CSR_GP_UCODE (CSR_BASE+0x044) -#define CSR_UCODE_DRV_GP1 (CSR_BASE+0x054) -#define CSR_UCODE_DRV_GP1_SET (CSR_BASE+0x058) -#define CSR_UCODE_DRV_GP1_CLR (CSR_BASE+0x05c) -#define CSR_UCODE_DRV_GP2 (CSR_BASE+0x060) -#define CSR_GIO_CHICKEN_BITS (CSR_BASE+0x100) - -/* Analog phase-lock-loop configuration (3945 only) - * Set bit 24. */ -#define CSR_ANA_PLL_CFG (CSR_BASE+0x20c) - -/* Bits for CSR_HW_IF_CONFIG_REG */ -#define CSR_HW_IF_CONFIG_REG_BIT_ALMAGOR_MB (0x00000100) -#define CSR_HW_IF_CONFIG_REG_BIT_ALMAGOR_MM (0x00000200) -#define CSR_HW_IF_CONFIG_REG_BIT_SKU_MRC (0x00000400) -#define CSR_HW_IF_CONFIG_REG_BIT_BOARD_TYPE (0x00000800) -#define CSR_HW_IF_CONFIG_REG_BITS_SILICON_TYPE_A (0x00000000) -#define CSR_HW_IF_CONFIG_REG_BITS_SILICON_TYPE_B (0x00001000) -#define CSR_HW_IF_CONFIG_REG_BIT_EEPROM_OWN_SEM (0x00200000) - -/* interrupt flags in INTA, set by uCode or hardware (e.g. dma), - * acknowledged (reset) by host writing "1" to flagged bits. */ -#define CSR_INT_BIT_FH_RX (1 << 31) /* Rx DMA, cmd responses, FH_INT[17:16] */ -#define CSR_INT_BIT_HW_ERR (1 << 29) /* DMA hardware error FH_INT[31] */ -#define CSR_INT_BIT_DNLD (1 << 28) /* uCode Download */ -#define CSR_INT_BIT_FH_TX (1 << 27) /* Tx DMA FH_INT[1:0] */ -#define CSR_INT_BIT_SCD (1 << 26) /* TXQ pointer advanced */ -#define CSR_INT_BIT_SW_ERR (1 << 25) /* uCode error */ -#define CSR_INT_BIT_RF_KILL (1 << 7) /* HW RFKILL switch GP_CNTRL[27] toggled */ -#define CSR_INT_BIT_CT_KILL (1 << 6) /* Critical temp (chip too hot) rfkill */ -#define CSR_INT_BIT_SW_RX (1 << 3) /* Rx, command responses, 3945 */ -#define CSR_INT_BIT_WAKEUP (1 << 1) /* NIC controller waking up (pwr mgmt) */ -#define CSR_INT_BIT_ALIVE (1 << 0) /* uCode interrupts once it initializes */ - -#define CSR_INI_SET_MASK (CSR_INT_BIT_FH_RX | \ - CSR_INT_BIT_HW_ERR | \ - CSR_INT_BIT_FH_TX | \ - CSR_INT_BIT_SW_ERR | \ - CSR_INT_BIT_RF_KILL | \ - CSR_INT_BIT_SW_RX | \ - CSR_INT_BIT_WAKEUP | \ - CSR_INT_BIT_ALIVE) - -/* interrupt flags in FH (flow handler) (PCI busmaster DMA) */ -#define CSR_FH_INT_BIT_ERR (1 << 31) /* Error */ -#define CSR_FH_INT_BIT_HI_PRIOR (1 << 30) /* High priority Rx, bypass coalescing */ -#define CSR_FH_INT_BIT_RX_CHNL2 (1 << 18) /* Rx channel 2 (3945 only) */ -#define CSR_FH_INT_BIT_RX_CHNL1 (1 << 17) /* Rx channel 1 */ -#define CSR_FH_INT_BIT_RX_CHNL0 (1 << 16) /* Rx channel 0 */ -#define CSR_FH_INT_BIT_TX_CHNL6 (1 << 6) /* Tx channel 6 (3945 only) */ -#define CSR_FH_INT_BIT_TX_CHNL1 (1 << 1) /* Tx channel 1 */ -#define CSR_FH_INT_BIT_TX_CHNL0 (1 << 0) /* Tx channel 0 */ - -#define CSR_FH_INT_RX_MASK (CSR_FH_INT_BIT_HI_PRIOR | \ - CSR_FH_INT_BIT_RX_CHNL2 | \ - CSR_FH_INT_BIT_RX_CHNL1 | \ - CSR_FH_INT_BIT_RX_CHNL0) - -#define CSR_FH_INT_TX_MASK (CSR_FH_INT_BIT_TX_CHNL6 | \ - CSR_FH_INT_BIT_TX_CHNL1 | \ - CSR_FH_INT_BIT_TX_CHNL0) - - -/* RESET */ -#define CSR_RESET_REG_FLAG_NEVO_RESET (0x00000001) -#define CSR_RESET_REG_FLAG_FORCE_NMI (0x00000002) -#define CSR_RESET_REG_FLAG_SW_RESET (0x00000080) -#define CSR_RESET_REG_FLAG_MASTER_DISABLED (0x00000100) -#define CSR_RESET_REG_FLAG_STOP_MASTER (0x00000200) - -/* GP (general purpose) CONTROL */ -#define CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY (0x00000001) -#define CSR_GP_CNTRL_REG_FLAG_INIT_DONE (0x00000004) -#define CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ (0x00000008) -#define CSR_GP_CNTRL_REG_FLAG_GOING_TO_SLEEP (0x00000010) - -#define CSR_GP_CNTRL_REG_VAL_MAC_ACCESS_EN (0x00000001) - -#define CSR_GP_CNTRL_REG_MSK_POWER_SAVE_TYPE (0x07000000) -#define CSR_GP_CNTRL_REG_FLAG_MAC_POWER_SAVE (0x04000000) -#define CSR_GP_CNTRL_REG_FLAG_HW_RF_KILL_SW (0x08000000) - - -/* EEPROM REG */ -#define CSR_EEPROM_REG_READ_VALID_MSK (0x00000001) -#define CSR_EEPROM_REG_BIT_CMD (0x00000002) - -/* EEPROM GP */ -#define CSR_EEPROM_GP_VALID_MSK (0x00000006) -#define CSR_EEPROM_GP_BAD_SIGNATURE (0x00000000) -#define CSR_EEPROM_GP_IF_OWNER_MSK (0x00000180) - -/* UCODE DRV GP */ -#define CSR_UCODE_DRV_GP1_BIT_MAC_SLEEP (0x00000001) -#define CSR_UCODE_SW_BIT_RFKILL (0x00000002) -#define CSR_UCODE_DRV_GP1_BIT_CMD_BLOCKED (0x00000004) -#define CSR_UCODE_DRV_GP1_REG_BIT_CT_KILL_EXIT (0x00000008) - -/* GPIO */ -#define CSR_GPIO_IN_BIT_AUX_POWER (0x00000200) -#define CSR_GPIO_IN_VAL_VAUX_PWR_SRC (0x00000000) -#define CSR_GPIO_IN_VAL_VMAIN_PWR_SRC CSR_GPIO_IN_BIT_AUX_POWER - -/* GI Chicken Bits */ -#define CSR_GIO_CHICKEN_BITS_REG_BIT_L1A_NO_L0S_RX (0x00800000) -#define CSR_GIO_CHICKEN_BITS_REG_BIT_DIS_L0S_EXIT_TIMER (0x20000000) - -/* CSR_ANA_PLL_CFG */ -#define CSR_ANA_PLL_CFG_SH (0x00880300) - /*=== HBUS (Host-side Bus) ===*/ #define HBUS_BASE (0x400) diff --git a/drivers/net/wireless/iwlwifi/iwl-3945.c b/drivers/net/wireless/iwlwifi/iwl-3945.c index 63e832cdba7..0fca35650ad 100644 --- a/drivers/net/wireless/iwlwifi/iwl-3945.c +++ b/drivers/net/wireless/iwlwifi/iwl-3945.c @@ -1154,19 +1154,19 @@ int iwl3945_hw_nic_init(struct iwl3945_priv *priv) if (rev_id & PCI_CFG_REV_ID_BIT_RTP) IWL_DEBUG_INFO("RTP type \n"); else if (rev_id & PCI_CFG_REV_ID_BIT_BASIC_SKU) { - IWL_DEBUG_INFO("ALM-MB type\n"); + IWL_DEBUG_INFO("3945 RADIO-MB type\n"); iwl3945_set_bit(priv, CSR_HW_IF_CONFIG_REG, - CSR_HW_IF_CONFIG_REG_BIT_ALMAGOR_MB); + CSR39_HW_IF_CONFIG_REG_BIT_3945_MB); } else { - IWL_DEBUG_INFO("ALM-MM type\n"); + IWL_DEBUG_INFO("3945 RADIO-MM type\n"); iwl3945_set_bit(priv, CSR_HW_IF_CONFIG_REG, - CSR_HW_IF_CONFIG_REG_BIT_ALMAGOR_MM); + CSR39_HW_IF_CONFIG_REG_BIT_3945_MM); } if (EEPROM_SKU_CAP_OP_MODE_MRC == priv->eeprom.sku_cap) { IWL_DEBUG_INFO("SKU OP mode is mrc\n"); iwl3945_set_bit(priv, CSR_HW_IF_CONFIG_REG, - CSR_HW_IF_CONFIG_REG_BIT_SKU_MRC); + CSR39_HW_IF_CONFIG_REG_BIT_SKU_MRC); } else IWL_DEBUG_INFO("SKU OP mode is basic\n"); @@ -1174,24 +1174,24 @@ int iwl3945_hw_nic_init(struct iwl3945_priv *priv) IWL_DEBUG_INFO("3945ABG revision is 0x%X\n", priv->eeprom.board_revision); iwl3945_set_bit(priv, CSR_HW_IF_CONFIG_REG, - CSR_HW_IF_CONFIG_REG_BIT_BOARD_TYPE); + CSR39_HW_IF_CONFIG_REG_BIT_BOARD_TYPE); } else { IWL_DEBUG_INFO("3945ABG revision is 0x%X\n", priv->eeprom.board_revision); iwl3945_clear_bit(priv, CSR_HW_IF_CONFIG_REG, - CSR_HW_IF_CONFIG_REG_BIT_BOARD_TYPE); + CSR39_HW_IF_CONFIG_REG_BIT_BOARD_TYPE); } if (priv->eeprom.almgor_m_version <= 1) { iwl3945_set_bit(priv, CSR_HW_IF_CONFIG_REG, - CSR_HW_IF_CONFIG_REG_BITS_SILICON_TYPE_A); + CSR39_HW_IF_CONFIG_REG_BITS_SILICON_TYPE_A); IWL_DEBUG_INFO("Card M type A version is 0x%X\n", priv->eeprom.almgor_m_version); } else { IWL_DEBUG_INFO("Card M type B version is 0x%X\n", priv->eeprom.almgor_m_version); iwl3945_set_bit(priv, CSR_HW_IF_CONFIG_REG, - CSR_HW_IF_CONFIG_REG_BITS_SILICON_TYPE_B); + CSR39_HW_IF_CONFIG_REG_BITS_SILICON_TYPE_B); } spin_unlock_irqrestore(&priv->lock, flags); diff --git a/drivers/net/wireless/iwlwifi/iwl-3945.h b/drivers/net/wireless/iwlwifi/iwl-3945.h index d281e42964d..1701e0b9b87 100644 --- a/drivers/net/wireless/iwlwifi/iwl-3945.h +++ b/drivers/net/wireless/iwlwifi/iwl-3945.h @@ -40,8 +40,9 @@ extern struct pci_device_id iwl3945_hw_card_ids[]; #define DRV_NAME "iwl3945" -#include "iwl-3945-hw.h" +#include "iwl-csr.h" #include "iwl-prph.h" +#include "iwl-3945-hw.h" #include "iwl-3945-debug.h" /* Default noise level to report when noise measurement is not available. diff --git a/drivers/net/wireless/iwlwifi/iwl-4965-hw.h b/drivers/net/wireless/iwlwifi/iwl-4965-hw.h index cc726215ab9..7e8cc9928b5 100644 --- a/drivers/net/wireless/iwlwifi/iwl-4965-hw.h +++ b/drivers/net/wireless/iwlwifi/iwl-4965-hw.h @@ -410,137 +410,6 @@ struct iwl4965_eeprom { #define PCI_REG_WUM8 0x0E8 #define PCI_CFG_PMC_PME_FROM_D3COLD_SUPPORT (0x80000000) -/*=== CSR (control and status registers) ===*/ -#define CSR_BASE (0x000) - -#define CSR_HW_IF_CONFIG_REG (CSR_BASE+0x000) /* hardware interface config */ -#define CSR_INT_COALESCING (CSR_BASE+0x004) /* accum ints, 32-usec units */ -#define CSR_INT (CSR_BASE+0x008) /* host interrupt status/ack */ -#define CSR_INT_MASK (CSR_BASE+0x00c) /* host interrupt enable */ -#define CSR_FH_INT_STATUS (CSR_BASE+0x010) /* busmaster int status/ack*/ -#define CSR_GPIO_IN (CSR_BASE+0x018) /* read external chip pins */ -#define CSR_RESET (CSR_BASE+0x020) /* busmaster enable, NMI, etc*/ -#define CSR_GP_CNTRL (CSR_BASE+0x024) - -/* - * Hardware revision info - * Bit fields: - * 31-8: Reserved - * 7-4: Type of device: 0x0 = 4965, 0xd = 3945 - * 3-2: Revision step: 0 = A, 1 = B, 2 = C, 3 = D - * 1-0: "Dash" value, as in A-1, etc. - * - * NOTE: Revision step affects calculation of CCK txpower for 4965. - */ -#define CSR_HW_REV (CSR_BASE+0x028) - -/* EEPROM reads */ -#define CSR_EEPROM_REG (CSR_BASE+0x02c) -#define CSR_EEPROM_GP (CSR_BASE+0x030) -#define CSR_GP_UCODE (CSR_BASE+0x044) -#define CSR_UCODE_DRV_GP1 (CSR_BASE+0x054) -#define CSR_UCODE_DRV_GP1_SET (CSR_BASE+0x058) -#define CSR_UCODE_DRV_GP1_CLR (CSR_BASE+0x05c) -#define CSR_UCODE_DRV_GP2 (CSR_BASE+0x060) -#define CSR_GIO_CHICKEN_BITS (CSR_BASE+0x100) - -/* - * Indicates hardware rev, to determine CCK backoff for txpower calculation. - * Bit fields: - * 3-2: 0 = A, 1 = B, 2 = C, 3 = D step - */ -#define CSR_HW_REV_WA_REG (CSR_BASE+0x22C) - -/* Hardware interface configuration bits */ -#define CSR_HW_IF_CONFIG_REG_BIT_KEDRON_R (0x00000010) -#define CSR_HW_IF_CONFIG_REG_MSK_BOARD_VER (0x00000C00) -#define CSR_HW_IF_CONFIG_REG_BIT_MAC_SI (0x00000100) -#define CSR_HW_IF_CONFIG_REG_BIT_RADIO_SI (0x00000200) -#define CSR_HW_IF_CONFIG_REG_BIT_EEPROM_OWN_SEM (0x00200000) - -/* interrupt flags in INTA, set by uCode or hardware (e.g. dma), - * acknowledged (reset) by host writing "1" to flagged bits. */ -#define CSR_INT_BIT_FH_RX (1 << 31) /* Rx DMA, cmd responses, FH_INT[17:16] */ -#define CSR_INT_BIT_HW_ERR (1 << 29) /* DMA hardware error FH_INT[31] */ -#define CSR_INT_BIT_DNLD (1 << 28) /* uCode Download */ -#define CSR_INT_BIT_FH_TX (1 << 27) /* Tx DMA FH_INT[1:0] */ -#define CSR_INT_BIT_SCD (1 << 26) /* TXQ pointer advanced */ -#define CSR_INT_BIT_SW_ERR (1 << 25) /* uCode error */ -#define CSR_INT_BIT_RF_KILL (1 << 7) /* HW RFKILL switch GP_CNTRL[27] toggled */ -#define CSR_INT_BIT_CT_KILL (1 << 6) /* Critical temp (chip too hot) rfkill */ -#define CSR_INT_BIT_SW_RX (1 << 3) /* Rx, command responses, 3945 */ -#define CSR_INT_BIT_WAKEUP (1 << 1) /* NIC controller waking up (pwr mgmt) */ -#define CSR_INT_BIT_ALIVE (1 << 0) /* uCode interrupts once it initializes */ - -#define CSR_INI_SET_MASK (CSR_INT_BIT_FH_RX | \ - CSR_INT_BIT_HW_ERR | \ - CSR_INT_BIT_FH_TX | \ - CSR_INT_BIT_SW_ERR | \ - CSR_INT_BIT_RF_KILL | \ - CSR_INT_BIT_SW_RX | \ - CSR_INT_BIT_WAKEUP | \ - CSR_INT_BIT_ALIVE) - -/* interrupt flags in FH (flow handler) (PCI busmaster DMA) */ -#define CSR_FH_INT_BIT_ERR (1 << 31) /* Error */ -#define CSR_FH_INT_BIT_HI_PRIOR (1 << 30) /* High priority Rx, bypass coalescing */ -#define CSR_FH_INT_BIT_RX_CHNL1 (1 << 17) /* Rx channel 1 */ -#define CSR_FH_INT_BIT_RX_CHNL0 (1 << 16) /* Rx channel 0 */ -#define CSR_FH_INT_BIT_TX_CHNL1 (1 << 1) /* Tx channel 1 */ -#define CSR_FH_INT_BIT_TX_CHNL0 (1 << 0) /* Tx channel 0 */ - -#define CSR_FH_INT_RX_MASK (CSR_FH_INT_BIT_HI_PRIOR | \ - CSR_FH_INT_BIT_RX_CHNL1 | \ - CSR_FH_INT_BIT_RX_CHNL0) - -#define CSR_FH_INT_TX_MASK (CSR_FH_INT_BIT_TX_CHNL1 | \ - CSR_FH_INT_BIT_TX_CHNL0) - - -/* RESET */ -#define CSR_RESET_REG_FLAG_NEVO_RESET (0x00000001) -#define CSR_RESET_REG_FLAG_FORCE_NMI (0x00000002) -#define CSR_RESET_REG_FLAG_SW_RESET (0x00000080) -#define CSR_RESET_REG_FLAG_MASTER_DISABLED (0x00000100) -#define CSR_RESET_REG_FLAG_STOP_MASTER (0x00000200) - -/* GP (general purpose) CONTROL */ -#define CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY (0x00000001) -#define CSR_GP_CNTRL_REG_FLAG_INIT_DONE (0x00000004) -#define CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ (0x00000008) -#define CSR_GP_CNTRL_REG_FLAG_GOING_TO_SLEEP (0x00000010) - -#define CSR_GP_CNTRL_REG_VAL_MAC_ACCESS_EN (0x00000001) - -#define CSR_GP_CNTRL_REG_MSK_POWER_SAVE_TYPE (0x07000000) -#define CSR_GP_CNTRL_REG_FLAG_MAC_POWER_SAVE (0x04000000) -#define CSR_GP_CNTRL_REG_FLAG_HW_RF_KILL_SW (0x08000000) - - -/* EEPROM REG */ -#define CSR_EEPROM_REG_READ_VALID_MSK (0x00000001) -#define CSR_EEPROM_REG_BIT_CMD (0x00000002) - -/* EEPROM GP */ -#define CSR_EEPROM_GP_VALID_MSK (0x00000006) -#define CSR_EEPROM_GP_BAD_SIGNATURE (0x00000000) -#define CSR_EEPROM_GP_IF_OWNER_MSK (0x00000180) - -/* UCODE DRV GP */ -#define CSR_UCODE_DRV_GP1_BIT_MAC_SLEEP (0x00000001) -#define CSR_UCODE_SW_BIT_RFKILL (0x00000002) -#define CSR_UCODE_DRV_GP1_BIT_CMD_BLOCKED (0x00000004) -#define CSR_UCODE_DRV_GP1_REG_BIT_CT_KILL_EXIT (0x00000008) - -/* GPIO */ -#define CSR_GPIO_IN_BIT_AUX_POWER (0x00000200) -#define CSR_GPIO_IN_VAL_VAUX_PWR_SRC (0x00000000) -#define CSR_GPIO_IN_VAL_VMAIN_PWR_SRC CSR_GPIO_IN_BIT_AUX_POWER - -/* GI Chicken Bits */ -#define CSR_GIO_CHICKEN_BITS_REG_BIT_L1A_NO_L0S_RX (0x00800000) -#define CSR_GIO_CHICKEN_BITS_REG_BIT_DIS_L0S_EXIT_TIMER (0x20000000) - /*=== HBUS (Host-side Bus) ===*/ #define HBUS_BASE (0x400) diff --git a/drivers/net/wireless/iwlwifi/iwl-4965.c b/drivers/net/wireless/iwlwifi/iwl-4965.c index 05ad5a9a1a5..2da153331a7 100644 --- a/drivers/net/wireless/iwlwifi/iwl-4965.c +++ b/drivers/net/wireless/iwlwifi/iwl-4965.c @@ -604,9 +604,9 @@ int iwl4965_hw_nic_init(struct iwl4965_priv *priv) /* set CSR_HW_CONFIG_REG for uCode use */ iwl4965_set_bit(priv, CSR_HW_IF_CONFIG_REG, - CSR_HW_IF_CONFIG_REG_BIT_KEDRON_R | - CSR_HW_IF_CONFIG_REG_BIT_RADIO_SI | - CSR_HW_IF_CONFIG_REG_BIT_MAC_SI); + CSR49_HW_IF_CONFIG_REG_BIT_4965_R | + CSR49_HW_IF_CONFIG_REG_BIT_RADIO_SI | + CSR49_HW_IF_CONFIG_REG_BIT_MAC_SI); rc = iwl4965_grab_nic_access(priv); if (rc < 0) { diff --git a/drivers/net/wireless/iwlwifi/iwl-4965.h b/drivers/net/wireless/iwlwifi/iwl-4965.h index 5c605129dfb..a782c454e0d 100644 --- a/drivers/net/wireless/iwlwifi/iwl-4965.h +++ b/drivers/net/wireless/iwlwifi/iwl-4965.h @@ -41,6 +41,7 @@ extern struct pci_device_id iwl4965_hw_card_ids[]; #define DRV_NAME "iwl4965" #include "iwl-4965-hw.h" +#include "iwl-csr.h" #include "iwl-prph.h" #include "iwl-4965-debug.h" diff --git a/drivers/net/wireless/iwlwifi/iwl-csr.h b/drivers/net/wireless/iwlwifi/iwl-csr.h new file mode 100644 index 00000000000..276ba281604 --- /dev/null +++ b/drivers/net/wireless/iwlwifi/iwl-csr.h @@ -0,0 +1,217 @@ +/****************************************************************************** + * + * This file is provided under a dual BSD/GPLv2 license. When using or + * redistributing this file, you may do so under either license. + * + * GPL LICENSE SUMMARY + * + * Copyright(c) 2005 - 2008 Intel Corporation. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of version 2 of the GNU General Public License as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110, + * USA + * + * The full GNU General Public License is included in this distribution + * in the file called LICENSE.GPL. + * + * Contact Information: + * James P. Ketrenos <ipw2100-admin@linux.intel.com> + * Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 + * + * BSD LICENSE + * + * Copyright(c) 2005 - 2007 Intel Corporation. All rights reserved. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * * Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * * Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * * Neither the name Intel Corporation nor the names of its + * contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, + * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT + * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, + * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY + * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + *****************************************************************************/ +/*=== CSR (control and status registers) ===*/ +#define CSR_BASE (0x000) + +#define CSR_HW_IF_CONFIG_REG (CSR_BASE+0x000) /* hardware interface config */ +#define CSR_INT_COALESCING (CSR_BASE+0x004) /* accum ints, 32-usec units */ +#define CSR_INT (CSR_BASE+0x008) /* host interrupt status/ack */ +#define CSR_INT_MASK (CSR_BASE+0x00c) /* host interrupt enable */ +#define CSR_FH_INT_STATUS (CSR_BASE+0x010) /* busmaster int status/ack*/ +#define CSR_GPIO_IN (CSR_BASE+0x018) /* read external chip pins */ +#define CSR_RESET (CSR_BASE+0x020) /* busmaster enable, NMI, etc*/ +#define CSR_GP_CNTRL (CSR_BASE+0x024) + +/* + * Hardware revision info + * Bit fields: + * 31-8: Reserved + * 7-4: Type of device: 0x0 = 4965, 0xd = 3945 + * 3-2: Revision step: 0 = A, 1 = B, 2 = C, 3 = D + * 1-0: "Dash" value, as in A-1, etc. + * + * NOTE: Revision step affects calculation of CCK txpower for 4965. + */ +#define CSR_HW_REV (CSR_BASE+0x028) + +/* EEPROM reads */ +#define CSR_EEPROM_REG (CSR_BASE+0x02c) +#define CSR_EEPROM_GP (CSR_BASE+0x030) +#define CSR_GP_UCODE (CSR_BASE+0x044) +#define CSR_UCODE_DRV_GP1 (CSR_BASE+0x054) +#define CSR_UCODE_DRV_GP1_SET (CSR_BASE+0x058) +#define CSR_UCODE_DRV_GP1_CLR (CSR_BASE+0x05c) +#define CSR_UCODE_DRV_GP2 (CSR_BASE+0x060) +#define CSR_GIO_CHICKEN_BITS (CSR_BASE+0x100) + +/* Analog phase-lock-loop configuration (3945 only) + * Set bit 24. */ +#define CSR_ANA_PLL_CFG (CSR_BASE+0x20c) +/* + * Indicates hardware rev, to determine CCK backoff for txpower calculation. + * Bit fields: + * 3-2: 0 = A, 1 = B, 2 = C, 3 = D step + */ +#define CSR_HW_REV_WA_REG (CSR_BASE+0x22C) + +/* Bits for CSR_HW_IF_CONFIG_REG */ +#define CSR49_HW_IF_CONFIG_REG_BIT_4965_R (0x00000010) +#define CSR49_HW_IF_CONFIG_REG_MSK_BOARD_VER (0x00000C00) +#define CSR49_HW_IF_CONFIG_REG_BIT_MAC_SI (0x00000100) +#define CSR49_HW_IF_CONFIG_REG_BIT_RADIO_SI (0x00000200) + +#define CSR39_HW_IF_CONFIG_REG_BIT_3945_MB (0x00000100) +#define CSR39_HW_IF_CONFIG_REG_BIT_3945_MM (0x00000200) +#define CSR39_HW_IF_CONFIG_REG_BIT_SKU_MRC (0x00000400) +#define CSR39_HW_IF_CONFIG_REG_BIT_BOARD_TYPE (0x00000800) +#define CSR39_HW_IF_CONFIG_REG_BITS_SILICON_TYPE_A (0x00000000) +#define CSR39_HW_IF_CONFIG_REG_BITS_SILICON_TYPE_B (0x00001000) + +#define CSR_HW_IF_CONFIG_REG_BIT_EEPROM_OWN_SEM (0x00200000) + +/* interrupt flags in INTA, set by uCode or hardware (e.g. dma), + * acknowledged (reset) by host writing "1" to flagged bits. */ +#define CSR_INT_BIT_FH_RX (1 << 31) /* Rx DMA, cmd responses, FH_INT[17:16] */ +#define CSR_INT_BIT_HW_ERR (1 << 29) /* DMA hardware error FH_INT[31] */ +#define CSR_INT_BIT_DNLD (1 << 28) /* uCode Download */ +#define CSR_INT_BIT_FH_TX (1 << 27) /* Tx DMA FH_INT[1:0] */ +#define CSR_INT_BIT_SCD (1 << 26) /* TXQ pointer advanced */ +#define CSR_INT_BIT_SW_ERR (1 << 25) /* uCode error */ +#define CSR_INT_BIT_RF_KILL (1 << 7) /* HW RFKILL switch GP_CNTRL[27] toggled */ +#define CSR_INT_BIT_CT_KILL (1 << 6) /* Critical temp (chip too hot) rfkill */ +#define CSR_INT_BIT_SW_RX (1 << 3) /* Rx, command responses, 3945 */ +#define CSR_INT_BIT_WAKEUP (1 << 1) /* NIC controller waking up (pwr mgmt) */ +#define CSR_INT_BIT_ALIVE (1 << 0) /* uCode interrupts once it initializes */ + +#define CSR_INI_SET_MASK (CSR_INT_BIT_FH_RX | \ + CSR_INT_BIT_HW_ERR | \ + CSR_INT_BIT_FH_TX | \ + CSR_INT_BIT_SW_ERR | \ + CSR_INT_BIT_RF_KILL | \ + CSR_INT_BIT_SW_RX | \ + CSR_INT_BIT_WAKEUP | \ + CSR_INT_BIT_ALIVE) + +/* interrupt flags in FH (flow handler) (PCI busmaster DMA) */ +#define CSR_FH_INT_BIT_ERR (1 << 31) /* Error */ +#define CSR_FH_INT_BIT_HI_PRIOR (1 << 30) /* High priority Rx, bypass coalescing */ +#define CSR39_FH_INT_BIT_RX_CHNL2 (1 << 18) /* Rx channel 2 (3945 only) */ +#define CSR_FH_INT_BIT_RX_CHNL1 (1 << 17) /* Rx channel 1 */ +#define CSR_FH_INT_BIT_RX_CHNL0 (1 << 16) /* Rx channel 0 */ +#define CSR39_FH_INT_BIT_TX_CHNL6 (1 << 6) /* Tx channel 6 (3945 only) */ +#define CSR_FH_INT_BIT_TX_CHNL1 (1 << 1) /* Tx channel 1 */ +#define CSR_FH_INT_BIT_TX_CHNL0 (1 << 0) /* Tx channel 0 */ + +#define CSR39_FH_INT_RX_MASK (CSR_FH_INT_BIT_HI_PRIOR | \ + CSR39_FH_INT_BIT_RX_CHNL2 | \ + CSR_FH_INT_BIT_RX_CHNL1 | \ + CSR_FH_INT_BIT_RX_CHNL0) + + +#define CSR39_FH_INT_TX_MASK (CSR39_FH_INT_BIT_TX_CHNL6 | \ + CSR_FH_INT_BIT_TX_CHNL1 | \ + CSR_FH_INT_BIT_TX_CHNL0) + +#define CSR49_FH_INT_RX_MASK (CSR_FH_INT_BIT_HI_PRIOR | \ + CSR_FH_INT_BIT_RX_CHNL1 | \ + CSR_FH_INT_BIT_RX_CHNL0) + +#define CSR49_FH_INT_TX_MASK (CSR_FH_INT_BIT_TX_CHNL1 | \ + CSR_FH_INT_BIT_TX_CHNL0) + + +/* RESET */ +#define CSR_RESET_REG_FLAG_NEVO_RESET (0x00000001) +#define CSR_RESET_REG_FLAG_FORCE_NMI (0x00000002) +#define CSR_RESET_REG_FLAG_SW_RESET (0x00000080) +#define CSR_RESET_REG_FLAG_MASTER_DISABLED (0x00000100) +#define CSR_RESET_REG_FLAG_STOP_MASTER (0x00000200) + +/* GP (general purpose) CONTROL */ +#define CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY (0x00000001) +#define CSR_GP_CNTRL_REG_FLAG_INIT_DONE (0x00000004) +#define CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ (0x00000008) +#define CSR_GP_CNTRL_REG_FLAG_GOING_TO_SLEEP (0x00000010) + +#define CSR_GP_CNTRL_REG_VAL_MAC_ACCESS_EN (0x00000001) + +#define CSR_GP_CNTRL_REG_MSK_POWER_SAVE_TYPE (0x07000000) +#define CSR_GP_CNTRL_REG_FLAG_MAC_POWER_SAVE (0x04000000) +#define CSR_GP_CNTRL_REG_FLAG_HW_RF_KILL_SW (0x08000000) + + +/* EEPROM REG */ +#define CSR_EEPROM_REG_READ_VALID_MSK (0x00000001) +#define CSR_EEPROM_REG_BIT_CMD (0x00000002) + +/* EEPROM GP */ +#define CSR_EEPROM_GP_VALID_MSK (0x00000006) +#define CSR_EEPROM_GP_BAD_SIGNATURE (0x00000000) +#define CSR_EEPROM_GP_IF_OWNER_MSK (0x00000180) + +/* UCODE DRV GP */ +#define CSR_UCODE_DRV_GP1_BIT_MAC_SLEEP (0x00000001) +#define CSR_UCODE_SW_BIT_RFKILL (0x00000002) +#define CSR_UCODE_DRV_GP1_BIT_CMD_BLOCKED (0x00000004) +#define CSR_UCODE_DRV_GP1_REG_BIT_CT_KILL_EXIT (0x00000008) + +/* GPIO */ +#define CSR_GPIO_IN_BIT_AUX_POWER (0x00000200) +#define CSR_GPIO_IN_VAL_VAUX_PWR_SRC (0x00000000) +#define CSR_GPIO_IN_VAL_VMAIN_PWR_SRC CSR_GPIO_IN_BIT_AUX_POWER + +/* GI Chicken Bits */ +#define CSR_GIO_CHICKEN_BITS_REG_BIT_L1A_NO_L0S_RX (0x00800000) +#define CSR_GIO_CHICKEN_BITS_REG_BIT_DIS_L0S_EXIT_TIMER (0x20000000) + + diff --git a/drivers/net/wireless/iwlwifi/iwl3945-base.c b/drivers/net/wireless/iwlwifi/iwl3945-base.c index 7a72048b0f4..cc71bdc8035 100644 --- a/drivers/net/wireless/iwlwifi/iwl3945-base.c +++ b/drivers/net/wireless/iwlwifi/iwl3945-base.c @@ -4570,9 +4570,9 @@ static void iwl3945_irq_tasklet(struct iwl3945_priv *priv) * atomic, make sure that inta covers all the interrupts that * we've discovered, even if FH interrupt came in just after * reading CSR_INT. */ - if (inta_fh & CSR_FH_INT_RX_MASK) + if (inta_fh & CSR39_FH_INT_RX_MASK) inta |= CSR_INT_BIT_FH_RX; - if (inta_fh & CSR_FH_INT_TX_MASK) + if (inta_fh & CSR39_FH_INT_TX_MASK) inta |= CSR_INT_BIT_FH_TX; /* Now service all interrupt bits discovered above. */ diff --git a/drivers/net/wireless/iwlwifi/iwl4965-base.c b/drivers/net/wireless/iwlwifi/iwl4965-base.c index f273395d4a3..0c60f594dfe 100644 --- a/drivers/net/wireless/iwlwifi/iwl4965-base.c +++ b/drivers/net/wireless/iwlwifi/iwl4965-base.c @@ -4918,9 +4918,9 @@ static void iwl4965_irq_tasklet(struct iwl4965_priv *priv) * atomic, make sure that inta covers all the interrupts that * we've discovered, even if FH interrupt came in just after * reading CSR_INT. */ - if (inta_fh & CSR_FH_INT_RX_MASK) + if (inta_fh & CSR49_FH_INT_RX_MASK) inta |= CSR_INT_BIT_FH_RX; - if (inta_fh & CSR_FH_INT_TX_MASK) + if (inta_fh & CSR49_FH_INT_TX_MASK) inta |= CSR_INT_BIT_FH_TX; /* Now service all interrupt bits discovered above. */ |