diff options
Diffstat (limited to 'drivers/scsi/lpfc/lpfc_mbox.c')
| -rw-r--r-- | drivers/scsi/lpfc/lpfc_mbox.c | 80 |
1 files changed, 79 insertions, 1 deletions
diff --git a/drivers/scsi/lpfc/lpfc_mbox.c b/drivers/scsi/lpfc/lpfc_mbox.c index ca358355ec9..65bc8e1a5f7 100644 --- a/drivers/scsi/lpfc/lpfc_mbox.c +++ b/drivers/scsi/lpfc/lpfc_mbox.c @@ -1,7 +1,7 @@ /******************************************************************* * This file is part of the Emulex Linux Device Driver for * * Fibre Channel Host Bus Adapters. * - * Copyright (C) 2004-2007 Emulex. All rights reserved. * + * Copyright (C) 2004-2008 Emulex. All rights reserved. * * EMULEX and SLI are trademarks of Emulex. * * www.emulex.com * * Portions Copyright (C) 2004-2005 Christoph Hellwig * @@ -272,6 +272,84 @@ lpfc_config_link(struct lpfc_hba * phba, LPFC_MBOXQ_t * pmb) } /** + * lpfc_config_msi: Prepare a mailbox command for configuring msi-x. + * @phba: pointer to lpfc hba data structure. + * @pmb: pointer to the driver internal queue element for mailbox command. + * + * The configure MSI-X mailbox command is used to configure the HBA's SLI-3 + * MSI-X multi-message interrupt vector association to interrupt attention + * conditions. + * + * Return codes + * 0 - Success + * -EINVAL - Failure + **/ +int +lpfc_config_msi(struct lpfc_hba *phba, LPFC_MBOXQ_t *pmb) +{ + MAILBOX_t *mb = &pmb->mb; + uint32_t attentionConditions[2]; + + /* Sanity check */ + if (phba->cfg_use_msi != 2) { + lpfc_printf_log(phba, KERN_ERR, LOG_INIT, + "0475 Not configured for supporting MSI-X " + "cfg_use_msi: 0x%x\n", phba->cfg_use_msi); + return -EINVAL; + } + + if (phba->sli_rev < 3) { + lpfc_printf_log(phba, KERN_ERR, LOG_INIT, + "0476 HBA not supporting SLI-3 or later " + "SLI Revision: 0x%x\n", phba->sli_rev); + return -EINVAL; + } + + /* Clear mailbox command fields */ + memset(pmb, 0, sizeof(LPFC_MBOXQ_t)); + + /* + * SLI-3, Message Signaled Interrupt Fearure. + */ + + /* Multi-message attention configuration */ + attentionConditions[0] = (HA_R0ATT | HA_R1ATT | HA_R2ATT | HA_ERATT | + HA_LATT | HA_MBATT); + attentionConditions[1] = 0; + + mb->un.varCfgMSI.attentionConditions[0] = attentionConditions[0]; + mb->un.varCfgMSI.attentionConditions[1] = attentionConditions[1]; + + /* + * Set up message number to HA bit association + */ +#ifdef __BIG_ENDIAN_BITFIELD + /* RA0 (FCP Ring) */ + mb->un.varCfgMSI.messageNumberByHA[HA_R0_POS] = 1; + /* RA1 (Other Protocol Extra Ring) */ + mb->un.varCfgMSI.messageNumberByHA[HA_R1_POS] = 1; +#else /* __LITTLE_ENDIAN_BITFIELD */ + /* RA0 (FCP Ring) */ + mb->un.varCfgMSI.messageNumberByHA[HA_R0_POS^3] = 1; + /* RA1 (Other Protocol Extra Ring) */ + mb->un.varCfgMSI.messageNumberByHA[HA_R1_POS^3] = 1; +#endif + /* Multi-message interrupt autoclear configuration*/ + mb->un.varCfgMSI.autoClearHA[0] = attentionConditions[0]; + mb->un.varCfgMSI.autoClearHA[1] = attentionConditions[1]; + + /* For now, HBA autoclear does not work reliably, disable it */ + mb->un.varCfgMSI.autoClearHA[0] = 0; + mb->un.varCfgMSI.autoClearHA[1] = 0; + + /* Set command and owner bit */ + mb->mbxCommand = MBX_CONFIG_MSI; + mb->mbxOwner = OWN_HOST; + + return 0; +} + +/** * lpfc_init_link: Prepare a mailbox command for initialize link on a HBA. * @phba: pointer to lpfc hba data structure. * @pmb: pointer to the driver internal queue element for mailbox command. |