diff options
Diffstat (limited to 'drivers/serial')
| -rw-r--r-- | drivers/serial/amba-pl010.c | 2 | ||||
| -rw-r--r-- | drivers/serial/amba-pl011.c | 38 | ||||
| -rw-r--r-- | drivers/serial/imx.c | 13 |
3 files changed, 37 insertions, 16 deletions
diff --git a/drivers/serial/amba-pl010.c b/drivers/serial/amba-pl010.c index cdc049d4350..58a4879c7e4 100644 --- a/drivers/serial/amba-pl010.c +++ b/drivers/serial/amba-pl010.c @@ -686,7 +686,7 @@ static int pl010_probe(struct amba_device *dev, struct amba_id *id) goto out; } - base = ioremap(dev->res.start, PAGE_SIZE); + base = ioremap(dev->res.start, resource_size(&dev->res)); if (!base) { ret = -ENOMEM; goto free; diff --git a/drivers/serial/amba-pl011.c b/drivers/serial/amba-pl011.c index 88fdac51b6c..bf82e28770a 100644 --- a/drivers/serial/amba-pl011.c +++ b/drivers/serial/amba-pl011.c @@ -70,6 +70,23 @@ struct uart_amba_port { struct clk *clk; unsigned int im; /* interrupt mask */ unsigned int old_status; + unsigned int ifls; /* vendor-specific */ +}; + +/* There is by now at least one vendor with differing details, so handle it */ +struct vendor_data { + unsigned int ifls; + unsigned int fifosize; +}; + +static struct vendor_data vendor_arm = { + .ifls = UART011_IFLS_RX4_8|UART011_IFLS_TX4_8, + .fifosize = 16, +}; + +static struct vendor_data vendor_st = { + .ifls = UART011_IFLS_RX_HALF|UART011_IFLS_TX_HALF, + .fifosize = 64, }; static void pl011_stop_tx(struct uart_port *port) @@ -360,8 +377,7 @@ static int pl011_startup(struct uart_port *port) if (retval) goto clk_dis; - writew(UART011_IFLS_RX4_8|UART011_IFLS_TX4_8, - uap->port.membase + UART011_IFLS); + writew(uap->ifls, uap->port.membase + UART011_IFLS); /* * Provoke TX FIFO interrupt into asserting. @@ -732,6 +748,7 @@ static struct uart_driver amba_reg = { static int pl011_probe(struct amba_device *dev, struct amba_id *id) { struct uart_amba_port *uap; + struct vendor_data *vendor = id->data; void __iomem *base; int i, ret; @@ -750,7 +767,7 @@ static int pl011_probe(struct amba_device *dev, struct amba_id *id) goto out; } - base = ioremap(dev->res.start, PAGE_SIZE); + base = ioremap(dev->res.start, resource_size(&dev->res)); if (!base) { ret = -ENOMEM; goto free; @@ -762,12 +779,13 @@ static int pl011_probe(struct amba_device *dev, struct amba_id *id) goto unmap; } + uap->ifls = vendor->ifls; uap->port.dev = &dev->dev; uap->port.mapbase = dev->res.start; uap->port.membase = base; uap->port.iotype = UPIO_MEM; uap->port.irq = dev->irq[0]; - uap->port.fifosize = 16; + uap->port.fifosize = vendor->fifosize; uap->port.ops = &amba_pl011_pops; uap->port.flags = UPF_BOOT_AUTOCONF; uap->port.line = i; @@ -812,6 +830,12 @@ static struct amba_id pl011_ids[] __initdata = { { .id = 0x00041011, .mask = 0x000fffff, + .data = &vendor_arm, + }, + { + .id = 0x00380802, + .mask = 0x00ffffff, + .data = &vendor_st, }, { 0, 0 }, }; @@ -845,7 +869,11 @@ static void __exit pl011_exit(void) uart_unregister_driver(&amba_reg); } -module_init(pl011_init); +/* + * While this can be a module, if builtin it's most likely the console + * So let's leave module_exit but move module_init to an earlier place + */ +arch_initcall(pl011_init); module_exit(pl011_exit); MODULE_AUTHOR("ARM Ltd/Deep Blue Solutions Ltd"); diff --git a/drivers/serial/imx.c b/drivers/serial/imx.c index 7b5d1de9cfe..285b414f305 100644 --- a/drivers/serial/imx.c +++ b/drivers/serial/imx.c @@ -71,7 +71,7 @@ #define ONEMS 0xb0 /* One Millisecond register */ #define UTS 0xb4 /* UART Test Register */ #endif -#if defined(CONFIG_ARCH_IMX) || defined(CONFIG_ARCH_MX1) +#ifdef CONFIG_ARCH_MX1 #define BIPR1 0xb0 /* Incremental Preset Register 1 */ #define BIPR2 0xb4 /* Incremental Preset Register 2 */ #define BIPR3 0xb8 /* Incremental Preset Register 3 */ @@ -101,7 +101,7 @@ #define UCR1_RTSDEN (1<<5) /* RTS delta interrupt enable */ #define UCR1_SNDBRK (1<<4) /* Send break */ #define UCR1_TDMAEN (1<<3) /* Transmitter ready DMA enable */ -#if defined(CONFIG_ARCH_IMX) || defined(CONFIG_ARCH_MX1) +#ifdef CONFIG_ARCH_MX1 #define UCR1_UARTCLKEN (1<<2) /* UART clock enabled */ #endif #if defined CONFIG_ARCH_MX3 || defined CONFIG_ARCH_MX2 @@ -132,7 +132,7 @@ #define UCR3_RXDSEN (1<<6) /* Receive status interrupt enable */ #define UCR3_AIRINTEN (1<<5) /* Async IR wake interrupt enable */ #define UCR3_AWAKEN (1<<4) /* Async wake interrupt enable */ -#ifdef CONFIG_ARCH_IMX +#ifdef CONFIG_ARCH_MX1 #define UCR3_REF25 (1<<3) /* Ref freq 25 MHz, only on mx1 */ #define UCR3_REF30 (1<<2) /* Ref Freq 30 MHz, only on mx1 */ #endif @@ -186,13 +186,6 @@ #define UTS_SOFTRST (1<<0) /* Software reset */ /* We've been assigned a range on the "Low-density serial ports" major */ -#ifdef CONFIG_ARCH_IMX -#define SERIAL_IMX_MAJOR 204 -#define MINOR_START 41 -#define DEV_NAME "ttySMX" -#define MAX_INTERNAL_IRQ IMX_IRQS -#endif - #ifdef CONFIG_ARCH_MXC #define SERIAL_IMX_MAJOR 207 #define MINOR_START 16 |