diff options
Diffstat (limited to 'drivers/serial')
| -rw-r--r-- | drivers/serial/imx.c | 65 |
1 files changed, 22 insertions, 43 deletions
diff --git a/drivers/serial/imx.c b/drivers/serial/imx.c index 5d7b58f1fe4..7485afd0df4 100644 --- a/drivers/serial/imx.c +++ b/drivers/serial/imx.c @@ -67,21 +67,8 @@ #define UBIR 0xa4 /* BRM Incremental Register */ #define UBMR 0xa8 /* BRM Modulator Register */ #define UBRC 0xac /* Baud Rate Count Register */ -#if defined CONFIG_ARCH_MX3 || defined CONFIG_ARCH_MX2 -#define ONEMS 0xb0 /* One Millisecond register */ -#define UTS 0xb4 /* UART Test Register */ -#endif -#ifdef CONFIG_ARCH_MX1 -#define BIPR1 0xb0 /* Incremental Preset Register 1 */ -#define BIPR2 0xb4 /* Incremental Preset Register 2 */ -#define BIPR3 0xb8 /* Incremental Preset Register 3 */ -#define BIPR4 0xbc /* Incremental Preset Register 4 */ -#define BMPR1 0xc0 /* BRM Modulator Register 1 */ -#define BMPR2 0xc4 /* BRM Modulator Register 2 */ -#define BMPR3 0xc8 /* BRM Modulator Register 3 */ -#define BMPR4 0xcc /* BRM Modulator Register 4 */ -#define UTS 0xd0 /* UART Test Register */ -#endif +#define MX2_ONEMS 0xb0 /* One Millisecond register */ +#define UTS (cpu_is_mx1() ? 0xd0 : 0xb4) /* UART Test Register */ /* UART Control Register Bit Fields.*/ #define URXD_CHARRDY (1<<15) @@ -101,12 +88,7 @@ #define UCR1_RTSDEN (1<<5) /* RTS delta interrupt enable */ #define UCR1_SNDBRK (1<<4) /* Send break */ #define UCR1_TDMAEN (1<<3) /* Transmitter ready DMA enable */ -#ifdef CONFIG_ARCH_MX1 -#define UCR1_UARTCLKEN (1<<2) /* UART clock enabled */ -#endif -#if defined CONFIG_ARCH_MX3 || defined CONFIG_ARCH_MX2 -#define UCR1_UARTCLKEN (0) /* not present on mx2/mx3 */ -#endif +#define MX1_UCR1_UARTCLKEN (1<<2) /* UART clock enabled, mx1 only */ #define UCR1_DOZE (1<<1) /* Doze */ #define UCR1_UARTEN (1<<0) /* UART enabled */ #define UCR2_ESCI (1<<15) /* Escape seq interrupt enable */ @@ -132,13 +114,9 @@ #define UCR3_RXDSEN (1<<6) /* Receive status interrupt enable */ #define UCR3_AIRINTEN (1<<5) /* Async IR wake interrupt enable */ #define UCR3_AWAKEN (1<<4) /* Async wake interrupt enable */ -#ifdef CONFIG_ARCH_MX1 -#define UCR3_REF25 (1<<3) /* Ref freq 25 MHz, only on mx1 */ -#define UCR3_REF30 (1<<2) /* Ref Freq 30 MHz, only on mx1 */ -#endif -#if defined CONFIG_ARCH_MX2 || defined CONFIG_ARCH_MX3 -#define UCR3_RXDMUXSEL (1<<2) /* RXD Muxed Input Select, on mx2/mx3 */ -#endif +#define MX1_UCR3_REF25 (1<<3) /* Ref freq 25 MHz, only on mx1 */ +#define MX1_UCR3_REF30 (1<<2) /* Ref Freq 30 MHz, only on mx1 */ +#define MX2_UCR3_RXDMUXSEL (1<<2) /* RXD Muxed Input Select, on mx2/mx3 */ #define UCR3_INVT (1<<1) /* Inverted Infrared transmission */ #define UCR3_BPEN (1<<0) /* Preset registers enable */ #define UCR4_CTSTL_32 (32<<10) /* CTS trigger level (32 chars) */ @@ -186,12 +164,10 @@ #define UTS_SOFTRST (1<<0) /* Software reset */ /* We've been assigned a range on the "Low-density serial ports" major */ -#ifdef CONFIG_ARCH_MXC #define SERIAL_IMX_MAJOR 207 #define MINOR_START 16 #define DEV_NAME "ttymxc" #define MAX_INTERNAL_IRQ MXC_INTERNAL_IRQS -#endif /* * This determines how often we check the modem status signals @@ -706,11 +682,11 @@ static int imx_startup(struct uart_port *port) } } -#if defined CONFIG_ARCH_MX2 || defined CONFIG_ARCH_MX3 - temp = readl(sport->port.membase + UCR3); - temp |= UCR3_RXDMUXSEL; - writel(temp, sport->port.membase + UCR3); -#endif + if (!cpu_is_mx1()) { + temp = readl(sport->port.membase + UCR3); + temp |= MX2_UCR3_RXDMUXSEL; + writel(temp, sport->port.membase + UCR3); + } if (USE_IRDA(sport)) { temp = readl(sport->port.membase + UCR4); @@ -942,9 +918,9 @@ imx_set_termios(struct uart_port *port, struct ktermios *termios, writel(num, sport->port.membase + UBIR); writel(denom, sport->port.membase + UBMR); -#ifdef ONEMS - writel(sport->port.uartclk / div / 1000, sport->port.membase + ONEMS); -#endif + if (!cpu_is_mx1()) + writel(sport->port.uartclk / div / 1000, + sport->port.membase + MX2_ONEMS); writel(old_ucr1, sport->port.membase + UCR1); @@ -1074,17 +1050,20 @@ static void imx_console_write(struct console *co, const char *s, unsigned int count) { struct imx_port *sport = imx_ports[co->index]; - unsigned int old_ucr1, old_ucr2; + unsigned int old_ucr1, old_ucr2, ucr1; /* * First, save UCR1/2 and then disable interrupts */ - old_ucr1 = readl(sport->port.membase + UCR1); + ucr1 = old_ucr1 = readl(sport->port.membase + UCR1); old_ucr2 = readl(sport->port.membase + UCR2); - writel((old_ucr1 | UCR1_UARTCLKEN | UCR1_UARTEN) & - ~(UCR1_TXMPTYEN | UCR1_RRDYEN | UCR1_RTSDEN), - sport->port.membase + UCR1); + if (cpu_is_mx1()) + ucr1 |= MX1_UCR1_UARTCLKEN; + ucr1 |= UCR1_UARTEN; + ucr1 &= ~(UCR1_TXMPTYEN | UCR1_RRDYEN | UCR1_RTSDEN); + + writel(ucr1, sport->port.membase + UCR1); writel(old_ucr2 | UCR2_TXEN, sport->port.membase + UCR2); |