| Age | Commit message (Collapse) | Author |
|---|
|
In the past flow control wasn't enabled by default under the
incorrect assumption that this opened up us to a denial of
service attack. However since any switch that forwarded flow
control would be extremely msiconfigured and/or buggy, this
concern no longer out weighs the preformance gains from
having FC enabled.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The priority flow control settings from the netlink layer aren't taking
effect in the base driver. The boolean pfc_mode_enable in the dcb_config
struct isn't being set, so the hardware configuration code is never
reached.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ethtool tries to get advertised speed from phy.autoneg_advertised.
However for copper media this wasn't happening until later do to
an other fix which moved mac.ops.setup_link_speed placement in
ixgbe_link_config(). This patch will display the default advertised
speeds if it can't yet get this information from phy.autoneg_advertised.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ixgbe driver had issues when DEBUG was defined because the hw_dbg macro
was incomplete. This patch completes the code based off of the code that
already existed in the igb module.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Impact: Fix
Yinghai Lu found one system with 82575EB where, in the kernel that is
kexeced, probe igb failed with -2, the reason being that the adapter
could not be brought back from D3 by the kexec kernel, most probably
due to quirky hardware (it looks like the same behavior happened on
forcedeth).
Prevent igb from putting the adapter into D3 during shutdown except
when we going to power off the system. For this purpose, seperate
igb_shutdown() from igb_suspend() and use the appropriate PCI PM
callbacks in both of them.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Reported-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The code path for setting up phy loopback testing was out of date and was
setting bits it didn't need to. This change cleans up the code path and
removes some code that has no effect on teh driver.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Increase the delay for copper phy init from 15ms to 100ms. This is to
address issues seen in which ethtool -t was failing in some cases on 82576
based adapters.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An issue was seen on suspend in which the system reported a page fault. This
was due to the new reg_idx code being called after the queues were freed.
This update prevents any for loops from going through the queues by setting
the number of queues to 0 when they are freed.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When device is on PCIe link trained as x2 the driver is currently reporting
link width as "unknown". The original patch provided by Myron adds the x2
link support and my changes are cosmetic to clean up the readability of the
conditional operators.
Based on work by: Myron Stowe <myron.stowe@hp.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The FEC Ethernet device isn't always attached to a phy. Be careful
not to dereference phy_device if it is NULL. Also eliminates an
unnecessary extra function from the ioctl path.
Reported-by: Henk Stegeman <henk.stegeman@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since not using net_device_ops gets you shunned out the cool crowd,
this patch modifies the fec_mpc52xx Ethernet driver to provide the
management hooks via a struct net_device_ops.
Reported-by: Henk Stegeman <henk.stegeman@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver triggers a BUG_ON() when allocating DMA buffers because the
arch/powerpc dma_ops aren't in the net_device's struct device. This
patch fixes the problem by using the parent of_device which does have
the correct dma_ops set.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 784544739a25c30637397ace5489eeb6e15d7d49
(netfilter: iptables: lock free counters) forgot to disable BH
in arpt_do_table(), ipt_do_table() and ip6t_do_table()
Use rcu_read_lock_bh() instead of rcu_read_lock() cures the problem.
Reported-and-bisected-by: Roman Mindalev <r000n@r000n.net>
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We have a 64bit value that needs to be set atomically.
This is easy and quick on all 64bit archs, and can also be done
on x86/32 with set_64bit() (uses cmpxchg8b). However other
32b archs don't have this.
I actually changed this to the current state in preparation for
mainline because the old way (using a spinlock on 32b) resulted in
unsightly #ifdefs in the code. But obviously, being correct takes
precedence.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This fixes a bug where a connection was unexpectedly
not on *any* list while being destroyed. It also
cleans up some code duplication and regularizes some
function names.
* Grab appropriate lock in conn_free() and explain in comment
* Ensure via locking that a conn is never not on either
a dev's list or the nodev list
* Add rds_xx_remove_conn() to match rds_xx_add_conn()
* Make rds_xx_add_conn() return void
* Rename remove_{,nodev_}conns() to
destroy_{,nodev_}conns() and unify their implementation
in a helper function
* Document lock ordering as nodev conn_lock before
dev_conn_lock
Reported-by: Yosef Etigin <yosefe@voltaire.com>
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rs_send_drop_to() is called during socket close. If it takes
m_rs_lock without disabling interrupts, then
rds_send_remove_from_sock() can run from the rx completion
handler and thus deadlock.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- Kconfig and Makefile related changes for vxge driver.
- No changes in current submission.
- Changes from previous submission -
- Incorporated the following review comments as per Bill Flink:
- Add dependancy on INET along with PCI
- Remove dependancy on INET_LRO and add GRO support.
- Made this patch as last patch as per Ben Hutchings comments.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Rastapur Santosh <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- Driver version
- Changes from previous submission -
- Updated driver version.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Rastapur Santosh <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch implements all ethtool related entry point functions for the driver.
- Changes in this submission -
- Removed redundant #include statements
- Changes in previous submissions -
- Removed unused statistics.
- General clean up - removed unused variables and macros.
- Incorporated following comments from Ben Hutchings
- No need to restart the interface in vxge_ethtool_sset
- Do not use #ifdef ADVERTISED_XX
- Remove unnecessart intermediate copy in vxge_ethtool_gdrvinfo
- Use strlcpy() to ensure null-termination.
- Use ethtool_op_get_tso, ethtool_op_set_tx_hw_csum instead
of redefining the same code.
- Implement get_strings_count instead of deprecated get_stats_count.
- Don't report reporting the EEPROM length as we don't supprt
get/set eeprom.
- Don't set self_test_count as we don't support any self tests.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Rastapur Santosh <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch implements all the driver entry point functions.
- Definition of all module loadable paramters.
- Implementation of all driver entry point functions.
- Changes in this submission -
- Fixed compilation error when enabling debug statements
- Fixed few warnings when CONFIG_PCI_MSI is not defined
- Removed unnecessary volatile variables
- Removed compare_ether_addr as it causes unaligned memory access on
the sparc64 platform.
- Changes in previous submissions -
- As per Stephen Hemminger's comments removed the following loadable
parameters - gro, rx_& tx max_indicate_pkts, exec_mode, rx & tx
pause_enable, tx_steering_type and intr_type.
- Added Device ID definition in vxge-main.h instead of
include/linux/pci_ids.h file - Reported by David Miller
- Incorporated following review comments from Ben Hutchings
- NAPI is always enabled (no option to turn it OFF).
- Loadable parameters
rx_steering_type: This loadable option is removed.
ring_blocks: This loadable option is removed.
The driver default settings work well in most if not all cases.
Another patch to configure these parameters with ethtool will be
released in the future.
- LRO has been deprecated in favour of GRO - Bill Fink & Dave Miller's comment
- Fixed sparse warnings - Reported by Andi Kleen
- Removed unused variables
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Rastapur Santosh <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch takes care of trafic handling related APIS.
- Interrupt Enable and disable
- Mask / Unmask Interrupt
- Traffic Interrupt handling.
- Alarm Interrupt handling.
- Changes in this submission -
- General clean up - removed redundant includes, defines and macros.
- Changes in previous submissions -
- General cleanup - removed unused functions and variables.
- Use asserts where necessary - Reported by Andi Kleen
- Fixed sparse warnings - Reported by Andi Kleen
- Use a prefix, "__vxge" in front of hw functions to make them globally
unique - Ben Hutchings
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Rastapur Santosh <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch takes care of Initialization and configuration steps of
Neterion Inc's X3100 Series 10GbE PCIe I/O Virtualized Server Adapter.
- Device Initialization.
- Verification and setting of device config parameters.
- Allocation of Tx FIFO and Rx Ring descriptors (DTR).
- APIs to get various type of hw stats
- APIs to configure RTS (Receive Traffic Steering)
- Changes in this submission -
- Include vmalloc header without which a compilation error occured
on sparc64, ppc64 and IA64 plaforms.
- Fixed compilation warning in register_poll, write32_upper,
write32_lower and the special write64 functions on ppc64.
- General cleanup - removed redundant includes and defines.
- Changes in previous submissions -
- Add readq/writeq implementation for the driver for 32 bit systems -
reported by Dave Miller.
- Incorporated following comments from Ben Hutchings
- Start a comment with "/**" to make it a kernel-doc comment.
- Use prefix, "__vxge" in front of hw functions to make them globally
unique.
- Fixed unnecessary clearing members of *channel just before freeing
- Use backslashes only for macro definitions and not in multi-line
statements.
- Used pci_find_capability instead of redefining it.
- Used device and revision ids that are already in pdev - no need to
read them again.
- Used pci_save_state() and pci_restore_state() around resets.
- Used udelay and mdelay directly instead of wrapper.
- In __vxge_hw_device_register_poll() reset i to 0 after the
microsecond delay loop to commence the millisecond delay loop.
- Corrected spelling "sapper" - should be "swapper"
- Remove too much vertical whitespace.
- Replaced magic numbers with appropriate macros
- Incorporated following comments from Andi Kleen [andi@firstfloor.org]
- Reduced the arguments in functions or refactored them into smaller
functions.
- Allocate page sized memories used in slow path with vmalloc.
- Use asserts where necessary.
- Use macros instead of magic numbers.
- Use the pci layer code instead of defining own functions
- Remove driver wrappers such as xge_hw_device_private_set().
- Fixed sparse warnings.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Rastapur Santosh <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- Complete Register map details of Neterion Inc's X3100 Series 10GbE PCIe I/O
Virtualized Server Adapter.
- No change from previous submission.
- Changes in previous submissions -
- Incorporated following comments from Ben Hutchings
- Use original macros for endian checks
- Remove VXGE_OS_PLATFORM_* macros as they are unused.
- Converted multiple bVALX macros into single with additional
width parameter and renamed it to vxge_bVALn.
- Using __packed instead of pragma pack(1)
- Added a comment of the use of a hw swapper so driver code is
portable (does not have to change the byte order for register
access as well as dma operations) on different ENDIAN platforms.
- Using the <linux/pci_regs.h> definitions instead of redefing them.
- Using the PCI capabilities registers in <linux/pci_regs.h>
instead of redefing them.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Rastapur Santosh <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- update to Maintainer list of S2IO 10GbE drivers (xframe/vxge).
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Rastapur Santosh <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- vxge driver help text file.
- No change from previous submission.
- Changes in previous submissions -
Removed the performance tuning section with instructions to disable
time stamps and change sysctl settings - Reported by Dave Miller
General clean up.
- Removed tx/rx_pause, exec_mode, tx_steering_type, rx_steering_type, gro,
intr_type, rx & tx max_indicate_pkts and exec_mode loadable parameters. The
driver default settings work well in most if not all cases. Another patch
to configure these parameters with ethtool will be released in the future -
Reported by Stephen Hemminger.
- Incorporated following fixes based on comments from Ben Hutchings
Removed references to earlier kernel versions.
Removed sections that are similar for all drivers -
Load/Unload
Identifying the adapter/interface
Boot time configuration
Removed loadable parameter -
NAPI - Napi is always enabled.
rx_steering_type & ring_blocks - The driver default settings
work well in most if not all cases. Another patch to configure
these parameters with ethtool will be released in the future.
Removed ethtool support section - No need to duplicate ethtool
docs here.
Removed Known Issue on SUSE 9 - Doesn't apply when using a
current kernel.
Removed Common Problems section - These don't apply to in-tree modules.
Removed Available Downloads section - Not sure this belongs in-tree.
Removed Copyright information - This notice doesn't belong in
the kernel.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Rastapur Santosh <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we use a shared legacy IRQ then our interrupt handler may be called
as soon as it is registered even though IRQs are disabled on the NIC.
Now that the legacy interrupt handler also checks for event delivery,
it may decide to schedule polling in this case. Ensure that the NAPI
context is valid but disabled at this point.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove pointless conditional before kfree().
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jaswinder/net-next-2.6
|
|
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Let driver depend on HAS_IOMEM to avoid build breakage on s390:
CC drivers/net/ethoc.o
drivers/net/ethoc.c: In function 'ethoc_read':
drivers/net/ethoc.c:221: error: implicit declaration of function 'ioread32'
drivers/net/ethoc.c: In function 'ethoc_write':
drivers/net/ethoc.c:226: error: implicit declaration of function 'iowrite32'
drivers/net/ethoc.c: In function 'ethoc_rx':
drivers/net/ethoc.c:405: error: implicit declaration of function 'memcpy_fromio'
drivers/net/ethoc.c: In function 'ethoc_start_xmit':
drivers/net/ethoc.c:828: error: implicit declaration of function 'memcpy_toio'
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added osi_load_firmware() instead of copying same thing twice
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
|
|
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
|
|
Added predef variable in add_mcs() to support predefined mcs data
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
|
|
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a dependency with IPv6:
ERROR: "__ipv6_addr_type" [net/netfilter/xt_cluster.ko] undefined!
This patch adds a function that checks if the higher bits of the
address is 0xFF to identify a multicast address, instead of adding a
dependency due to __ipv6_addr_type(). I came up with this idea after
Patrick McHardy pointed possible problems with runtime module
dependencies.
Reported-by: Steven Noonan <steven@uplinklabs.net>
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Reported-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can't put 'mdio' until after we've used it in the
fsl_pq_mdio_bus_name() call.
Also fix error return values.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can't put 'mdio' until after we've used it in the
fsl_pq_mdio_bus_name() call.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All users have been removed.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allows for the removal of byteswapping in some places and
the removal of HIPQUAD (replaced by %pI4).
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dcc_ip is treated as a host-endian value in the first printk,
but the second printk uses %pI4 which expects a be32. This
will cause a mismatch between the debug statement and the
warning statement.
Treat as a be32 throughout and avoid some byteswapping during
some comparisions, and allow another user of HIPQUAD to bite the
dust.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
drivers/net/hamradio/dmascc.c:587: error: 'struct net_device' has no
member named 'set_mac_address'
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When GRO/frag_list support was added to GSO, I made an error
which broke the support for segmenting linear GSO packets (GSO
packets are normally non-linear in the payload).
These days most of these packets are constructed by the tun
driver, which prefers to allocate linear memory if possible.
This is fixed in the latest kernel, but for 2.6.29 and earlier
it is still the norm.
Therefore this bug causes failures with GSO when used with tun
in 2.6.29.
Reported-by: James Huang <jamesclhuang@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add missing struct field to fix kernel-doc warning:
Warning(include/linux/skbuff.h:182): No description found for parameter 'flags'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c-core: Some style cleanups
i2c-piix4: Add support for the Broadcom HT1100 chipset
i2c-piix4: Add support to SB800 SMBus changes
i2c-pca-platform: Use defaults if no platform_data given
i2c-algo-pca: Use timeout for checking the state machine
i2c-algo-pca: Rework waiting for a free bus
i2c-algo-pca: Add PCA9665 support
i2c: Adapt debug macros for KERN_* constants
i2c-davinci: Fix timeout handling
i2c: Adapter timeout is in jiffies
i2c: Set a default timeout value for all adapters
i2c: Add missing KERN_* constants to printks
i2c-algo-pcf: Handle timeout correctly
i2c-algo-pcf: Style cleanups
eeprom/at24: Remove EXPERIMENTAL
i2c-nforce2: Add support for MCP67, MCP73, MCP78S and MCP79
i2c: Clarify which clients are auto-removed
i2c: Let checkpatch shout on users of the legacy model
i2c: Document the different ways to instantiate i2c devices
|
|
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (422 commits)
[ARM] 5435/1: fix compile warning in sanity_check_meminfo()
[ARM] 5434/1: ARM: OMAP: Fix mailbox compile for 24xx
[ARM] pxa: fix the bad assumption that PCMCIA sockets always start with 0
[ARM] pxa: fix Colibri PXA300 and PXA320 LCD backlight pins
imxfb: Fix TFT mode
i.MX21/27: remove ifdef CONFIG_FB_IMX
imxfb: add clock support
mxc: add arch_reset() function
clkdev: add possibility to get a clock based on the device name
i.MX1: remove fb support from mach-imx
[ARM] pxa: build arch/arm/plat-pxa/mfp.c only when PXA3xx or ARCH_MMP defined
Gemini: Add support for Teltonika RUT100
Gemini: gpiolib based GPIO support v2
MAINTAINERS: add myself as Gemini architecture maintainer
ARM: Add Gemini architecture v3
[ARM] OMAP: Fix compile for omap2_init_common_hw()
MAINTAINERS: Add myself as Faraday ARM core variant maintainer
ARM: Add support for FA526 v2
[ARM] acorn,ebsa110,footbridge,integrator,sa1100: Convert asm/io.h to linux/io.h
[ARM] collie: fix two minor formatting nits
...
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/arjan/linux-2.6-async-for-30:
fastboot: remove duplicate unpack_to_rootfs()
ide/net: flip the order of SATA and network init
async: remove the temporary (2.6.29) "async is off by default" code
Fix up conflicts in init/initramfs.c manually
|
