| Age | Commit message (Collapse) | Author |
|---|
|
The RX buffer poison needs to be refreshed, if we recycle an RX buffer,
because it might be (partially) overwritten by some DMA operations.
Cc: stable@kernel.org
Cc: Francesco Gringoli <francesco.gringoli@ing.unibs.it>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch adds poisoning and sanity checking to the RX DMA buffers.
This is used for protection against buggy hardware/firmware that raises
RX interrupts without doing an actual DMA transfer.
This mechanism protects against rare "bad packets" (due to uninitialized skb data)
and rare kernel crashes due to uninitialized RX headers.
The poison is selected to not match on valid frames and to be cheap for checking.
The poison check mechanism _might_ trigger incorrectly, if we are voluntarily
receiving frames with bad PLCP headers. However, this is nonfatal, because the
chance of such a match is basically zero and in case it happens it just results
in dropping the packet.
Bad-PLCP RX defaults to off, and you should leave it off unless you want to listen
to the latest news broadcasted by your microwave oven.
This patch also moves the initialization of the RX-header "length" field in front of
the mapping of the DMA buffer. The CPU should not touch the buffer after we mapped it.
Cc: stable@kernel.org
Reported-by: Francesco Gringoli <francesco.gringoli@ing.unibs.it>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Currently rx status for frames which are completed from reorder buffer
is taken from it's cb area which is not always right, cb is not holding
the rx status when driver uses mac80211's non-irq rx handler to pass it's
received frames. This results in dropping almost all frames from reorder
buffer when security is enabled by doing double decryption (first in hw,
second in sw because of wrong rx status). This patch copies rx status into
cb area before the frame is put into reorder buffer. After this patch,
there is a significant improvement in throughput with ath9k + WPA2(AES).
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We won't ever get here as regulatory_hint_core() can only fail
on -ENOMEM and in that case we don't initialize cfg80211 but this is
technically correct code.
This is actually good for stable, where we don't check for -ENOMEM
failure on __regulatory_hint()'s failure.
Cc: stable@kernel.org
Reported-by: Quentin Armitage <Quentin@armitage.org.uk>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The commit a390d1f3 ("phylib: convert state_queue work to
delayed_work") missed converting 'expires' value to 'delay' value.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prevent ixgbe from putting the adapter into D3 during shutdown except when
we're going to power off the system, since doing that may generally cause
problems with kexec to happen (such problems were observed for igb and
forcedeth). For this purpose seperate ixgbe_shutdown() from ixgbe_suspend()
and use the appropriate PCI PM callbacks in both of them.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prevent e1000e from putting the adapter into D3 during shutdown except when
we're going to power off the system, since doing that may generally cause
problems with kexec to happen (such problems were observed for igb and
forcedeth). For this purpose seperate e1000e_shutdown() from e1000e_suspend()
and use the appropriate PCI PM callbacks in both of them.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prevent e1000 from putting the adapter into D3 during shutdown except when
we're going to power off the system, since doing that may generally cause
problems with kexec to happen (such problems were observed for igb and
forcedeth). For this purpose seperate e1000_shutdown() from e1000_suspend()
and use the appropriate PCI PM callbacks in both of them.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Latest tcpdump/libpcap triggers annoying messages because of high order page
allocation failures (when lowmem exhausted or fragmented)
These allocation errors are correctly handled so could be silent.
[22660.208901] tcpdump: page allocation failure. order:5, mode:0xc0d0
[22660.208921] Pid: 13866, comm: tcpdump Not tainted 2.6.30-rc2 #170
[22660.208936] Call Trace:
[22660.208950] [<c04e2b46>] ? printk+0x18/0x1a
[22660.208965] [<c02760f7>] __alloc_pages_internal+0x357/0x460
[22660.208980] [<c0276251>] __get_free_pages+0x21/0x40
[22660.208995] [<c04cc835>] packet_set_ring+0x105/0x3d0
[22660.209009] [<c04ccd1d>] packet_setsockopt+0x21d/0x4d0
[22660.209025] [<c0270400>] ? filemap_fault+0x0/0x450
[22660.209040] [<c0449e34>] sys_setsockopt+0x54/0xa0
[22660.209053] [<c044b97f>] sys_socketcall+0xef/0x270
[22660.209067] [<c0202e34>] sysenter_do_call+0x12/0x26
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After a transmit timed out, the reset task will be called, which will free the
allocated resources(stop_gfar). If gfar_poll will be called before the
resources get allocated again gfar_clean_tx_ring will call
dev_kfree_skb_any(NULL).
Example crash:
ops: Kernel access of bad area, sig: 11 [#1]
PREEMPT RSBBA100
Modules linked in:
NIP: c01a10c4 LR: c013b254 CTR: c013c038
REGS: c02e7d20 TRAP: 0300 Not tainted (2.6.27.20)
MSR: 00001032 <ME,IR,DR> CR: 24000082 XER: 20000000
DAR: 000000a0, DSISR: 20000000
TASK = c02ce578[0] 'swapper' THREAD: c02e6000
GPR00: 000000a0 c02e7dd0 c02ce578 00000000 00000040 00000001 c02ec1c0
00001032
GPR08: c080d1e0 df9ea800 00000000 00000000 24000082 ffffffff 0404f000
00000000
GPR16: ffffffbf ffffffff ffffffff ffdff7ff ffffffff c02d0fd4 00100100
00200200
GPR24: c031220c 00000001 00000001 00000000 00000000 df849800 ff109000
df849b80
NIP [c01a10c4] dev_kfree_skb_irq+0x18/0x70
LR [c013b254] gfar_clean_tx_ring+0x70/0x11c
Call Trace:
[c02e7dd0] [c003e978] update_wall_time+0x730/0x744 (unreliable)
[c02e7df0] [c013b254] gfar_clean_tx_ring+0x70/0x11c
[c02e7e10] [c013c07c] gfar_poll+0x44/0x150
[c02e7e30] [c01a064c] net_rx_action+0xa8/0x19c
[c02e7e70] [c00251d4] __do_softirq+0x64/0xc0
[c02e7e90] [c0006384] do_softirq+0x40/0x58
[c02e7ea0] [c00250a8] irq_exit+0x40/0x9c
[c02e7eb0] [c000642c] do_IRQ+0x90/0xac
[c02e7ec0] [c0010ab4] ret_from_except+0x0/0x14
--- Exception: 501 at cpu_idle+0x9c/0xf8
LR = cpu_idle+0x9c/0xf8
[c02e7f80] [c0009820] cpu_idle+0x58/0xf8 (unreliable)
[c02e7fa0] [c01fb8c8] __got2_end+0x7c/0x90
[c02e7fc0] [c026c794] start_kernel+0x2c0/0x2d4
[c02e7ff0] [00003438] 0x3438
Instruction dump:
7fa00124 80010024 bba10014 38210020 7c0803a6 4e800020 9421ffe0 7c0802a6
7c6b1b78 90010024 380300a0 bfa10014 <7d200028> 3129ffff 7d20012d 40a2fff4
Kernel panic - not syncing: Fatal exception in interrupt
This Patch calls netif_stop_queue before calling stop_gfar.
Signed-off-by: Markus Brunner <super.firetwister@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add LRO alignment initially committed in
621544eb8c3beaa859c75850f816dd9b056a00a3 ("[LRO]: fix lro_gen_skb()
alignment") and removed in 0dcffac1a329be69bab0ac604bf7283737108e68
("myri10ge: add multislices support") during conversion to
multi-slice.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the update of real_num_tx_queues from
ixgbe_acquire_msix_vectors() to ixgbe_set_num_queues(), to ensure it
be always in sync with num_tx_queues.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't do the num_tx_queues based masking on calculating tx queue
index.
1) num_tx_queues is not always power-of-2, because it also depends on
the online cpu numbers. So the masking could be a performance bug
on a 6 cpu system.
2) queue_mapping will be limited by real_num_tx_queues=num_tx_queues
in the generic netdev function set_cur_queue_map(). So the bound
limiting here is not necessary.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 244f46ae6e9e18f6fc0be7d1f49febde4762c34b.
Alan Cox did the research, and just like the other radio protocols
zero-length frames have meaning because at the top level ROSE is
X.25 PLP.
So this zero-length filtering is invalid.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
falcon_sim_phy_event() used EFX_OWORD_FIELD, which operates on
bitfields in 128-bit values, on an event, which is a 64-bit value.
This should be harmless - these macros always use little-endian
ordering, so it would read and write back the following 8 bytes
unchanged - but it is obviously wrong.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sfc could call netif_napi_add() multiple times for the same
napi_struct, corrupting the list of napi_structs for the associated
device and leading to a busy-loop on device removal. Move the call to
netif_napi_add() and add a call to netif_napi_del() in the obvious
places.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove debug printk I accidently left in as part of commit:
commit 6146b1a4da98377e4abddc91ba5856bef8f23f1e
Author: Jay Vosburgh <fubar@us.ibm.com>
Date: Tue Nov 4 17:51:15 2008 -0800
bonding: Fix ALB mode to balance traffic on VLANs
Reported by Duncan Gibb <duncan.gibb@siriusit.co.uk>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
e1000/e1000e compile report a possible unused variable, fix
that for now. Shortly after this a small refactor and bug
fix will follow in the same code.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reported-by: Subrata Modak <subrata@linux.vnet.ibm.com>
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The BUG_ON(skge->tx_ring.to_use != skge->tx_ring.to_clean) in skge_up()
was sometimes observed when setting MTU.
skge_down() disables the TX queue, but then reenables it by mistake via
skge_tx_clean().
Fix it by moving the waking of the queue from skge_tx_clean() to the
other caller. And to make sure start_xmit is not in progress on another
CPU, skge_down() should call netif_tx_disable().
The bug was reported to me by Jiri Jilek whose Debian system sometimes
failed to boot. He tested the patch and the bug did not happen anymore.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since everybody has been focusing on baremetal GRO performance
no one noticed when I added a bug that zapped gso_size for all
GRO packets. This only gets picked up when you forward the skb
out of an interface.
Thanks to Mark Wagner for noticing this bug when testing kvm.
Reported-by: Mark Wagner <mwagner@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After switch (rthdr->type) {...},the check below is completely useless.Because:
if the type is 2,then hdrlen must be 2 and segments_left must be 1,clearly the
check is redundant;if the type is not 2,then goto sticky_done,the check is useless
too.
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com>
Reviewed-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When I made the tun driver use non-linear packets as the preferred
option, it broke non-GSO users because they would end up allocating
a completely non-linear packet, which triggers a crash when we call
eth_type_trans.
This patch reverts non-GSO users to using linear packets and adds
a check to ensure that GSO users can't cause crashes in the same
way.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A long-standing feature in tcp_init_metrics() is such that
any of its goto reset prevents call to tcp_init_cwnd().
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When vlan acceleration is used on receive, the vlan tag is maintained
outside of the skb data. The existing vlan tag match only works on TX
path because it uses vlan_get_tag which tests for VLAN_HW_TX_ACCEL.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hi:
gro: Normalise skb before bypassing GRO on netpoll VLAN path
When we detect netpoll RX on the GRO VLAN path we bail out and
call the normal VLAN receive handler. However, the packet needs
to be normalised by calling eth_type_trans since that's what the
normal path expects (normally the GRO path does the fixup).
This patch adds the necessary call to vlan_gro_frags.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Thanks,
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the default value of pause auto-negotiation supported
by PCS.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add did_interrupt() function to check if a PHY port
really caused an interrupt. This is needed in the case
of shared PHY interrupt pin configuration to stop
interrupt event processing for PHY ports which didn't
cause an interrupt.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Marvell 88E1121R Dual PHY device can be hardware-configured
to use shared interrupt pin for both PHY ports. For such
PHY configurations using shared PHY interrupt phy_interrupt()
handler will also schedule a work for PHY port which didn't
cause an interrupt.
This patch adds a possibility for PHY drivers to provide
did_interrupt() function which reports if the PHY (or a PHY
port in a multi-PHY device) generated an interrupt. This
function is called in phy_change() as phy_change() shouldn't
proceed if it is invoked for a PHY which didn't cause an
interrupt. So check for interrupt originator in phy_change()
to allow early-out.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the Marvell M88E1121R Dual GigE PHY
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
MAINTAINERS
|
|
We noticed on parisc that our broadcoms all swapped MAC addresses going
from 2.6.29 to 2.6.30-rc1:
Apr 11 07:48:24 ion kernel: eth0: Tigon3 [partno(BCM95700A6) rev 0105] (PCI:66MHz:64-bit) MAC address 00:30:6e:4b:15:59
Apr 13 07:34:34 ion kernel: eth0: Tigon3 [partno(BCM95700A6) rev 0105] (PCI:66MHz:64-bit) MAC address 00:00:59:15:4b:6e
The problem patch is:
commit 6d348f2c1e0bb1cf7a494b51fc921095ead3f6ae
Author: Matt Carlson <mcarlson@broadcom.com>
Date: Wed Feb 25 14:25:52 2009 +0000
tg3: Eliminate tg3_nvram_read_swab()
With the root cause being the use of memcpy to set the mac address:
memcpy(&dev->dev_addr[0], ((char *)&hi) + 2, 2);
memcpy(&dev->dev_addr[2], (char *)&lo, sizeof(lo));
This might work on little endian machines, but it can't on big endian
ones. You have to use the original setting mechanism to be correct on
all architectures.
The attached patch fixes parisc.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes:
docbook: make cleandocs
kbuild: fix spurious initramfs rebuild
Documentation: explain the difference between __bitwise and __bitwise__
kbuild: make it possible for the linker to discard local symbols from vmlinux
kbuild: remove pointless strdup() on arguments passed to new_module() in modpost
kbuild: fix a few typos in top-level Makefile
kbuild: introduce destination-y for exported headers
kbuild: use git svn instead of git-svn in setlocalversion
kconfig: fix update-po-config to accect backslash in input
kbuild: fix option processing for -I in headerdep
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ata: fix obviously wrong comment
ahci: force CAP_NCQ for earlier NV MCPs
[libata] sata_via: kill uninit'd var warning
|
