aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2009-04-22rndis_wlan: change quality level scaleJussi Kivilinna
Change quality level scale to match cfg80211 CFG80211_SIGNAL_TYPE_UNSPEC. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22cfg80211: add cfg80211_inform_bssJussi Kivilinna
Added cfg80211_inform_bss() for full-mac devices to use. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22rndis_wlan: convert get/set mode to cfg80211John W. Linville
Signed-off-by: John W. Linville <linville@tuxdriver.com> [edit: made rndis_change_virtual_intf static] Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22rndis_wlan: initiate cfg80211 conversionJohn W. Linville
Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22p54: add beacon filtering supportChristian Lamparter
This patch adds beacon filtering support to p54. Signed-off-by: Christian Lamparter <chunkeey@web.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22p54: more SoftLED updatesChristian Lamparter
This patch hopefully finishes the SoftLED code: - It adds two more LEDs (rx and radio). (the FW claims it can support up to 16 LEDs, but I doubt that any vendor put more than 4 on a board) - update the LEDs in a _delayed_ workqueue. No one reported any more crashes. (see: "PATCH] p54: fix race condition in memory management") So we can stop burning the mm code. Signed-off-by: Christian Lamparter <chunkeey@web.de> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22p54: clean up p54.h's struct p54_commonChristian Lamparter
This patch rearrange and regroups most elements in p54_common. Signed-off-by: Christian Lamparter <chunkeey@web.de> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22net/ps3: Update maintainerMasakazu Mokuno
Update the MAINTAINERS entry for PS3 NETWORK SUPPORT. CC: Masakazu Mokuno <mokuno@sm.sony.co.jp> Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22ath5k: reduce exported channel listBob Copeland
Claiming every available 5 ghz channel has a couple of negative side-effects: scanning takes a long time, and the channel list overflows the available buffer space for netlink commands, resulting in: $ iw phy phy0 info command failed: No buffer space available (-105) This patch adds a modparam so people who want to see all the channels can do so by passing all_channels=1. By default users will see a smaller list of channels. This also halves scan time, from 10 seconds down to less than 5 when using world regulatory. Changes-licensed-under: 3-Clause-BSD Signed-off-by: Bob Copeland <me@bobcopeland.com> Reported-by: Simon Farnsworth <simon@farnz.org.uk> Tested-By: Simon Farnsworth <simon@farnz.org.uk> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22mac80211: move ieee80211_enable_ht function to mlme.cJohannes Berg
It really belongs into that file since it is only relevant for managed mode. Move 1:1, not even whitespace changes, but make it static and remove from header file. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22ath9k: Fix bug in determining HT40 modeSujith
This patch fixes a bug in checking for HT40 mode. The STA's mode can be determined from the cached HT capabilities, use that and remove the redundant variable 'rc_phy_mode'. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22ath9k: Determine number of streams from HT capabilitiesSujith
The number of streams supported by a STA can be determined directly from the HT capabilities. Remove the redundant variable storing the stream cap. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22ath9k: Clean Interrupt handling routineSujith
This patch cleans up the ISR, removing a unnecessary do..while loop, and waking up the chip before getting the pending interrupts. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22ath9k: Trivial fix to handle AMPDU params properlySujith
Handle aggregation params only when aggregation is supported. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22ath9k: Initialize values when setting up the queue parametersSujith
Also fix a small typo. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22ath9k: Remove the useless do..while loopsSujith
These are unnecessary constructs in a function. This patch removes these from both RX and TX init routines. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22ath9k: Remove TIM from the interrupt maskSujith
We never handle TIM, TIM_TIMER is used instead. Remove this and the unnecessary swBeaconProcess variable. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22ath9k: Check for root debugfs fileSujith
Creation of the root debugfs file could have failed for some reason, check properly before proceeding in this case. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22ath9k: Remove unused structuresSujith
struct aggr_rifs_param and ath_tx_stat are not used anywhere. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22ath9k: Remove a couple of unused variables in descriptor handlingSujith
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22ath9k: Cleanup buffer status handlingSujith
Using a u32 to store a single flag is overkill. Use a bool to store whether the buffer is stale or not. Also, use u8 instead of u32 to store the buffer type. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22ath9k: Avoid unneeded castsSujith
Change the void pointer to struct sk_buff and access bf_mpdu directly, removing all casts in the process. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22ath9k: Remove redundant variable for Interrupt MitigationSujith
The state is already stored in ath9k_ops_config, so remove the duplicate variable in ath_hw. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22ath9k: Change return value of ath9k_hw_fill_cap_infoSujith
This routine always return true, checking for false in the return value is invalid. Fix this. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22ath9k: Cleanup debug messagesSujith
Clean debug messages to use appropriate levels, remove useless messages, and trim the number of debug levels. Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22ath9k: Remove redundant chainmask checkSujith
We get the valid chainmasks on HW attach, checking it again during reset is redundant. This patch removes the check. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22ath9k: Remove a few unused flagsSujith
This patch removes unused HW capability flags and HW operation variables, and a chainmask flag that we don't use anywhere. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22ath9k: No need to abort Rx path when autosleep is enabled.Vivek Natarajan
For chipsets supporting autosleep feature, there is no need to abort Rx engine since they are capable of automatically going back to sleep after receiving a packet. Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22b43: Do not "select" HW_RANDOMMichael Buesch
Auto-depend on HW_RANDOM, rather than "select"ing it. This way the user has the choice to enable or disable HWRNG support. Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22rt2x00: Fix Sparse warningIvo van Doorn
rt2x00link_reset_qual() is not declared in a header, and is only internally used within rt2x00link.c. It should be declared as static. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22rt2x00: Move Move pci_dev specific access to rt2x00pciIvo van Doorn
pci_dev->irq and pci_name(pci_dev) access should be limited to rt2x00pci only. This is more generic and allows a rt2x00 pci driver to be controlled as PCI device but also as platform driver (needed for rt2800pci SoC support). Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22ar9170: fix hang on stopChristian Lamparter
This patch fixes a locking problem which freezes the network core. The deadlock goes as follows: - ar9170_op_stop - is called 1. change the state to IDLE 2. > take the MUTEX < 3. cancel_SYNC all pending work, which means "block until a work_struct's callback has terminated" => if filter_config_work was queued it tries to get the MUTEX, before checking the device state... Signed-off-by: Christian Lamparter <chunkeey@web.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22ath5k: fix scanning in AR2424Pavel Roskin
AR5K_PHY_PLL_40MHZ_5413 should not be ORed with AR5K_PHY_MODE_RAD_RF5112 for 5 GHz channels. The incorrect PLL value breaks scanning in the countries where 5 GHz channels are allowed. Signed-off-by: Pavel Roskin <proski@gnu.org> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22ath9k: Update maintainers for ath9kLuis R. Rodriguez
This has been the case really, we just forgot to update it. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22nl80211: Add Michael MIC failure eventJouni Malinen
Define a new nl80211 event, NL80211_CMD_MICHAEL_MIC_FAILURE, to be used to notify user space about locally detected Michael MIC failures. This matches with the MLME-MICHAELMICFAILURE.indication() primitive. Since we do not actually have TSC in the skb anymore when mac80211_ev_michael_mic_failure() is called, that function is changed to take in the TSC as an optional parameter instead of as a requirement to include the TSC after the hdr field (which we did not really follow). For now, TSC is not included in the events from mac80211, but it could be added at some point. Signed-off-by: Jouni Malinen <j@w1.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22nl80211: Generate deauth/disassoc event for locally generated framesJouni Malinen
Previously, nl80211 mlme events were generated only for received deauthentication and disassociation frames. We need to do the same for locally generated ones in order to let applications know that we disconnected (e.g., when AP does not reply to a probe). Rename the nl80211 and cfg80211 functions (s/rx_//) to make it clearer that they are used for both received and locally generated frames. Signed-off-by: Jouni Malinen <j@w1.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22nl80211: Require auth type for NL80211_CMD_AUTHENTICATEJouni Malinen
NL80211_ATTR_AUTH_TYPE is a required parameter for NL80211_CMD_AUTHENTICATE. We are currently (by chance) defaulting to open system authentication if the attribute is not specified. It is better to just reject the invalid command. Signed-off-by: Jouni Malinen <j@w1.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22nl80211: remove duplicated #includeHuang Weiyi
Remove duplicated #include in net/wireless/core.h. Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22cfg80211: remove duplicated #includeHuang Weiyi
Remove duplicated #include in include/net/cfg80211.h. Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22rfkill-input: remove unused codeJohannes Berg
There's a lot of rfkill-input code that cannot ever be compiled and is useless until somebody needs and tests it -- therefore remove it. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22rfkill: remove user_claim stuffJohannes Berg
Almost all drivers do not support user_claim, so remove it completely and always report -EOPNOTSUPP to userspace. Since userspace cannot really drive rfkill _anyway_ (due to the odd restrictions imposed by the documentation) having this code is just pointless. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22rfkill: remove deprecated state constantsJohannes Berg
I only did superficial review, but these constants are stupid to have and without proper warnings nobody will review the code anyway, no amount of shouting will help. Also fix wimax to use correct states. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22nl80211: validate some input betterJohannes Berg
This patch changes nl80211 to: * validate that any IE input is a valid IE (stream) * move some validation code before locking * require that a reason code is given for both deauth/disassoc Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22mac80211: Don't access managed mode bits in non-managed modeVasanthakumar Thiagarajan
This fixes a stupid bug introduced in 25f85c31d4f.. Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22p54spi: compensate firmware alignment bug in p54spi_rxMax Filippov
Firmware may insert up to 4 padding bytes after the lmac header, but it does not amend the size of SPI data transfer. Such packets has correct data size in header, thus referencing past the end of allocated skb. Put extra 4 bytes to the end of the received skb to compensate for this case. Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Acked-by: Christian Lamparter <chunkeey@web.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22iwl3945: use iwl_mac_conf_txAbhijeet Kolekar
3945 now uses iwl_mac_conf_tx. Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22iwlwifi: merge and better support of suspend/resume for iwlagn and iwl3945Wey-Yi Guy
With mac80211's help to call stop() and start() in mac80211 suspend/resume function, both iwlagn and iwl3945 no longer calling stop() and start(); remove un-necessary STATUS_IN_SUSPEND bit from both header files and functions, Move apm_ops.stop() function into pci_suspend() to ensure DMA is stopped before go into suspend mode. iwl3945 has the similar suspend/resume function as iwlagn, so move both functions to iwlcore to be shared by both drivers. Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22p54spi: fix p54spi_tx_frame DMA transfer initiation and skb cleanupMax Filippov
p54spi_tx_frame wasn't waiting for HOST_ALLOWED in SPI_ADRS_DMA_WRITE_CTRL. This resulted in frequent 'WR_READY timeout' on beacon resubmission. Also don't free skb on error path, as it gets freed on p54spi_wq_tx. Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Acked-by: Christian Lamparter <chunkeey@web.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22libertas: support mesh for various firmware versionsBing Zhao
CMD_MESH_CONFIG command ID and a couple of structure members in TxPD, RxPD have been changed in firmware version 10.x.y.z and newer. Signed-off-by: Kiran Divekar <dkiran@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22p54spi: fix p54spi_upload_firmwareMax Filippov
Instead of firmware itself p54_upload_firmware was sending to the device content of struct firmware and the following random garbage. Notice '&' before priv->firmware->data at p54spi_spi_write. But simple removing of '&' sign triggered BUG_ON at dma_cache_maint. Thus kmemdup - kfree workaround. Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@web.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-12 13:03:07 +0000