aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2008-10-31mac80211: fix short slot handlingJohannes Berg
This patch makes mac80211 handle short slot requests from the AP properly. Also warn about uses of IEEE80211_CONF_SHORT_SLOT_TIME and optimise out the code since it cannot ever be hit anyway. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-10-31mac80211: remove max_antenna_gain configJohannes Berg
The antenna gain isn't exactly configurable, despite the belief of some unnamed individual who thinks that the EEPROM might influence it. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-10-31mac80211: clean up ieee80211_hw_config errorsJohannes Berg
Warn when ieee80211_hw_config returns an error, it shouldn't happen; remove a number of printks that would happen in such a case and one printk that is user-triggerable. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-10-31mac80211: remove wiphy_to_hwJohannes Berg
This isn't used by anyone, if we ever need it we can add it back, until then it's useless. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-10-31mac80211: minor code cleanupsJohannes Berg
Nothing very interesting, some checkpatch inspired stuff, some other things. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-10-31mac80211: remove writable debugs mesh parametersJohannes Berg
These parameters shouldn't be configurable via debugfs, if they need to be configurable nl80211 support has to be added, if not then they don't need to be writable here either. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Cc: Javier Cardona <javier@cozybit.com> Cc: Luis Carlos Cobo <luisca@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-10-31mac80211: remove aggregation status write support from debugfsJohannes Berg
This code uses static variables and thus cannot be kept. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-10-31misc: replace NIPQUAD()Harvey Harrison
Using NIPQUAD() with NIPQUAD_FMT, %d.%d.%d.%d or %u.%u.%u.%u can be replaced with %pI4 Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-31fs: replace NIPQUAD()Harvey Harrison
Using NIPQUAD() with NIPQUAD_FMT, %d.%d.%d.%d or %u.%u.%u.%u can be replaced with %pI4 Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-31drivers: replace NIPQUAD()Harvey Harrison
Using NIPQUAD() with NIPQUAD_FMT, %d.%d.%d.%d or %u.%u.%u.%u can be replaced with %pI4 Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-31net: replace NIPQUAD() in net/*/Harvey Harrison
Using NIPQUAD() with NIPQUAD_FMT, %d.%d.%d.%d or %u.%u.%u.%u can be replaced with %pI4 Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-31net: replace NIPQUAD() in net/netfilter/Harvey Harrison
Using NIPQUAD() with NIPQUAD_FMT, %d.%d.%d.%d or %u.%u.%u.%u can be replaced with %pI4 Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-31net: replace NIPQUAD() in net/ipv4/ net/ipv6/Harvey Harrison
Using NIPQUAD() with NIPQUAD_FMT, %d.%d.%d.%d or %u.%u.%u.%u can be replaced with %pI4 Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-31net: replace NIPQUAD() in net/ipv4/netfilter/Harvey Harrison
Using NIPQUAD() with NIPQUAD_FMT, %d.%d.%d.%d or %u.%u.%u.%u can be replaced with %pI4 Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-31pkt_sched: Add peek emulation for non-work-conserving qdiscs.Jarek Poplawski
This patch adds qdisc_peek_dequeued() wrapper to emulate peek method with qdisc->dequeue() and storing "peeked" skb in qdisc->gso_skb until dequeuing. This is mainly for compatibility reasons not to break some strange configs because peeking is expected for non-work-conserving parent qdiscs to query work-conserving child qdiscs. This implementation requires using qdisc_dequeue_peeked() wrapper instead of directly calling qdisc->dequeue() for all qdiscs ever querried with qdisc->ops->peek() or qdisc_peek_dequeued(). Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-31pkt_sched: Use qdisc->ops->peek() instead of ->dequeue() & ->requeue()Jarek Poplawski
Use qdisc->ops->peek() instead of ->dequeue() & ->requeue() pair. After this patch the only remaining user of qdisc->ops->requeue() is netem_enqueue(). Based on ideas of Herbert Xu, Patrick McHardy and David S. Miller. Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-31pkt_sched: Add qdisc->ops->peek() implementation.Jarek Poplawski
Add qdisc->ops->peek() implementation for work-conserving qdiscs. With feedback from Patrick McHardy. Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-31pkt_sched: sch_generic: Add generic qdisc->ops->peek() implementation.Jarek Poplawski
With feedback from Patrick McHardy. Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-31pkt_sched: Add ->peek() methods for fifo, prio and SFQ qdiscs.Patrick McHardy
From: Patrick McHardy <kaber@trash.net> Just as a demonstration how easy adding a peek operation to the work-conserving qdiscs actually is. It doesn't need to keep or change any internal state in many cases thanks to the guarantee that the packet will either be dequeued or, if another packet arrives, the upper qdisc will immediately ->peek again to reevaluate the state. (This is only slightly modified Patrick's patch.) Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-31pkt_sched: sch_generic: Add Qdisc_ops peek() method.Jarek Poplawski
Add Qdisc_ops peek() method in order to replace requeuing. Based on ideas and patches of Herbert Xu, Patrick McHardy and David S. Miller. Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-31xfrm: remove unused struct xfrm_policy::nextAlexey Dobriyan
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-31xfrm: C99 for xfrm_dev_notifierAlexey Dobriyan
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-31Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/wireless/p54/p54common.c
2008-10-31xfrm: do not leak ESRCH to user spacefernando@oss.ntt.co
I noticed that, under certain conditions, ESRCH can be leaked from the xfrm layer to user space through sys_connect. In particular, this seems to happen reliably when the kernel fails to resolve a template either because the AF_KEY receive buffer being used by racoon is full or because the SA entry we are trying to use is in XFRM_STATE_EXPIRED state. However, since this could be a transient issue it could be argued that EAGAIN would be more appropriate. Besides this error code is not even documented in the man page for sys_connect (as of man-pages 3.07). Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-31net: Really remove all of LOOPBACK_TSO code.David S. Miller
As noticed by Saikiran Madugula, commit 7447ef63cf2dfdc444f4c72ae13f604350b2e25f ("loopback: Remove rest of LOOPBACK_TSO code.") got rid of emulate_large_send_offload() but didn't get rid of the call site as well. Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-30Merge branch 'master' of git://git.infradead.org/users/pcmoore/lblnet-2.6David S. Miller
2008-10-30netfilter: nf_conntrack_proto_gre: switch to register_pernet_gen_subsys()Alexey Dobriyan
register_pernet_gen_device() can't be used is nf_conntrack_pptp module is also used (compiled in or loaded). Right now, proto_gre_net_exit() is called before nf_conntrack_pptp_net_exit(). The former shutdowns and frees GRE piece of netns, however the latter absolutely needs it to flush keymap. Oops is inevitable. Switch to shiny new register_pernet_gen_subsys() to get correct ordering in netns ops list. Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-30netns: add register_pernet_gen_subsys/unregister_pernet_gen_subsysAlexey Dobriyan
netns ops which are registered with register_pernet_gen_device() are shutdown strictly before those which are registered with register_pernet_subsys(). Sometimes this leads to opposite (read: buggy) shutdown ordering between two modules. Add register_pernet_gen_subsys()/unregister_pernet_gen_subsys() for modules which aren't elite enough for entry in struct net, and which can't use register_pernet_gen_device(). PPTP conntracking module is such one. Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-30net: delete excess kernel-doc notationRandy Dunlap
Remove excess kernel-doc function parameters from networking header & driver files: Warning(include/net/sock.h:946): Excess function parameter or struct member 'sk' description in 'sk_filter_release' Warning(include/linux/netdevice.h:1545): Excess function parameter or struct member 'cpu' description in 'netif_tx_lock' Warning(drivers/net/wan/z85230.c:712): Excess function parameter or struct member 'regs' description in 'z8530_interrupt' Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-30Merge branch 'davem-fixes' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
2008-10-30Merge branch 'master' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
2008-10-30pppoe: Fix socket leak.David S. Miller
Move SKB trim before we lookup the socket so we don't have to put it on failure. Based upon an initial patch by Jarek Poplawski and suggestions from Herbert Xu. Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-31gianfar: Don't reset TBI<->SerDes link if it's already upTrent Piepho
The link may be up already via the chip's reset strapping, or though action of U-Boot, or from the last time the interface was brought up. Resetting the link causes it to go down for several seconds. This can significantly increase the time from power-on to DHCP completion and a device being accessible to the network. Signed-off-by: Trent Piepho <tpiepho@freescale.com> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-31gianfar: Fix race in TBI/SerDes configurationTrent Piepho
The init_phy() function attaches to the PHY, then configures the SerDes<->TBI link (in SGMII mode). The TBI is on the MDIO bus with the PHY (sort of) and is accessed via the gianfar's MDIO registers, using the functions gfar_local_mdio_read/write(), which don't do any locking. The previously attached PHY will start a work-queue on a timer, and probably an irq handler as well, which will talk to the PHY and thus use the MDIO bus. This uses phy_read/write(), which have locking, but not against the gfar_local_mdio versions. The result is that PHY code will try to use the MDIO bus at the same time as the SerDes setup code, corrupting the transfers. Setting up the SerDes before attaching to the PHY will insure that there is no race between the SerDes code and *our* PHY, but doesn't fix everything. Typically the PHYs for all gianfar devices are on the same MDIO bus, which is associated with the first gianfar device. This means that the first gianfar's SerDes code could corrupt the MDIO transfers for a different gianfar's PHY. The lock used by phy_read/write() is contained in the mii_bus structure, which is pointed to by the PHY. This is difficult to access from the gianfar drivers, as there is no link between a gianfar device and the mii_bus which shares the same MDIO registers. As far as the device layer and drivers are concerned they are two unrelated devices (which happen to share registers). Generally all gianfar devices' PHYs will be on the bus associated with the first gianfar. But this might not be the case, so simply locking the gianfar's PHY's mii bus might not lock the mii bus that the SerDes setup code is going to use. We solve this by having the code that creates the gianfar platform device look in the device tree for an mdio device that shares the gianfar's registers. If one is found the ID of its platform device is saved in the gianfar's platform data. A new function in the gianfar mii code, gfar_get_miibus(), can use the bus ID to search through the platform devices for a gianfar_mdio device with the right ID. The platform device's driver data is the mii_bus structure, which the SerDes setup code can use to lock the current bus. Signed-off-by: Trent Piepho <tpiepho@freescale.com> CC: Andy Fleming <afleming@freescale.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-31pci: use pci_ioremap_bar() in drivers/netArjan van de Ven
Use the newly introduced pci_ioremap_bar() function in drivers/net. pci_ioremap_bar() just takes a pci device and a bar number, with the goal of making it really hard to get wrong, while also having a central place to stick sanity checks. Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-31tc35815: Define more Rx status bitsAtsushi Nemoto
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-31cxgb3 - enable lro control through ethtoolDivy Le Ray
Implement ethtool's get_flags and set_flags methods. It enables ethtool to control the LRO settings. Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-31e100: adapt to the reworked PCI PMRafael J. Wysocki
Adapt the e100 driver to the reworked PCI PM * Use the observation that it is sufficient to call pci_enable_wake() once, unless it fails Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Tested-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: Jesse Barnes <jbarnes@virtuousgeek.org> Cc: Jeff Garzik <jeff@garzik.org> Cc: Frans Pop <elendil@planet.nl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-31The overdue eepro100 removal.Adrian Bunk
Signed-off-by: Adrian Bunk <bunk@kernel.org> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-31skge: adapt skge to use reworked PCI PMRafael J. Wysocki
Adapt the skge driver to the reworked PCI PM * Use device_set_wakeup_enable() and friends as needed * Remove an open-coded reference to the standard PCI PM registers * Use pci_prepare_to_sleep() and pci_back_from_sleep() in the ->suspend() and ->resume() callbacks * Use the observation that it is sufficient to call pci_enable_wake() once, unless it fails Tested on Asus L5D (Yukon-Lite rev 7). Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Cc: Stephen Hemminger <shemminger@linux-foundation.org> Cc: Jeff Garzik <jeff@garzik.org> Cc: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-31at91_ether: request/free GPIO for PHY interruptDavid Brownell
When the at91_ether driver is using a GPIO for its PHY interrupt, be sure to request (and later, if needed, free) that GPIO. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-31amd8111e: fix dma_free_coherent contextChunbo Luo
Acoording commit aa24886e379d2b641c5117e178b15ce1d5d366ba, dma_free_coherent() need irqs enabled. This patch fix following warning messages: WARNING: at linux/arch/x86/kernel/pci-dma.c:376 dma_free_coherent+0xaa/0xb0() Call Trace: [<ffffffff8023f80f>] warn_on_slowpath+0x5f/0x90 [<ffffffff80496ffa>] ? __kfree_skb+0x3a/0xa0 [<ffffffff802a4723>] ? discard_slab+0x23/0x40 [<ffffffff8021274a>] dma_free_coherent+0xaa/0xb0 [<ffffffff8043668f>] amd8111e_close+0x10f/0x1b0 [<ffffffff8049f3ae>] dev_close+0x5e/0xb0 [<ffffffff8049efa1>] dev_change_flags+0xa1/0x1e0 [<ffffffff806b2171>] ic_close_devs+0x36/0x4e [<ffffffff806b29ee>] ip_auto_config+0x581/0x10f3 [<ffffffff803a6e19>] ? kobject_add+0x69/0x90 [<ffffffff803a698a>] ? kobject_get+0x1a/0x30 [<ffffffff803a785b>] ? kobject_uevent+0xb/0x10 [<ffffffff803a6c62>] ? kset_register+0x52/0x60 [<ffffffff803a6f9b>] ? kset_create_and_add+0x6b/0xa0 [<ffffffff804e2e74>] ? tcp_ca_find+0x24/0x50 [<ffffffff806b246d>] ? ip_auto_config+0x0/0x10f3 [<ffffffff8020903c>] _stext+0x3c/0x150 [<ffffffff802772d3>] ? register_irq_proc+0xd3/0xf0 [<ffffffff802f0000>] ? mb_cache_create+0x80/0x1f0 [<ffffffff80688693>] kernel_init+0x141/0x1b8 [<ffffffff80688552>] ? kernel_init+0x0/0x1b8 [<ffffffff8020d609>] child_rip+0xa/0x11 [<ffffffff80688552>] ? kernel_init+0x0/0x1b8 [<ffffffff80688552>] ? kernel_init+0x0/0x1b8 [<ffffffff8020d5ff>] ? child_rip+0x0/0x11 Signed-off-by: Chunbo Luo <chunbo.luo@windriver.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-31atl1: fix vlan tag regressionJay Cliburn
Commit 401c0aabec4b97320f962a0161a846d230a6f7aa introduced a regression in the atl1 driver by storing the VLAN tag in the wrong TX descriptor field. This patch causes the VLAN tag to be stored in its proper location. Tested-by: Ramon Casellas <ramon.casellas@cttc.es> Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net> Cc: stable@kernel.org Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-31SMC91x: delete unused local variable "lp"Mike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-31myri10ge: fix stop/go mmio orderingBrice Goglin
Use mmiowb() to ensure "stop" and "go" commands are sent in order on ia64. Signed-off-by: Brice Goglin <brice@myri.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-31bonding: fix panic when taking bond interface down before removing moduleAndy Gospodarek
A panic was discovered with bonding when using mode 5 or 6 and trying to remove the slaves from the bond after the interface was taken down. When calling 'ifconfig bond0 down' the following happens: bond_close() bond_alb_deinitialize() tlb_deinitialize() kfree(bond_info->tx_hashtbl) bond_info->tx_hashtbl = NULL Unfortunately if there are still slaves in the bond, when removing the module the following happens: bonding_exit() bond_free_all() bond_release_all() bond_alb_deinit_slave() tlb_clear_slave() tx_hash_table = BOND_ALB_INFO(bond).tx_hashtbl u32 next_index = tx_hash_table[index].next As you might guess we panic when trying to access a few entries into the table that no longer exists. I experimented with several options (like moving the calls to tlb_deinitialize somewhere else), but it really makes the most sense to be part of the bond_close routine. It also didn't seem logical move tlb_clear_slave around too much, so the simplest option seems to add a check in tlb_clear_slave to make sure we haven't already wiped the tx_hashtbl away before searching for all the non-existent hash-table entries that used to point to the slave as the output interface. Signed-off-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-31bonding: Clean up resource leaksJay Vosburgh
This patch reworks the resource free logic performed at the time a bonding device is released. This (a) closes two resource leaks, one for workqueues and one for multicast lists, and (b) improves commonality of code between the "destroy one" and "destroy all" paths by performing final free activity via destructor instead of explicitly (and differently) in each path. "Sean E. Millichamp" <sean@bruenor.org> reported the workqueue leak, and included a different patch. Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-31bonding: fix miimon failure counterJay Vosburgh
During the rework of the mii monitor for: commit f0c76d61779b153dbfb955db3f144c62d02173c2 Author: Jay Vosburgh <fubar@us.ibm.com> Date: Wed Jul 2 18:21:58 2008 -0700 bonding: refactor mii monitor I left out the increment of the link failure counter. This patch corrects that omission. Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-30Merge branch 'for-linus' of git://neil.brown.name/mdLinus Torvalds
* 'for-linus' of git://neil.brown.name/md: md: destroy partitions and notify udev when md array is stopped.
2008-10-30Merge git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linusLinus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus: lguest: fix irq vectors. lguest: fix early_ioremap. lguest: fix example launcher compile after moved asm-x86 dir.
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-29 18:28:36 +0000