| Age | Commit message (Collapse) | Author |
|---|
|
In the case where procfs is disabled, create_proc_profile() does not
exist. Stub it in with the others.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
mm/page_cgroup.c: In function 'init_section_page_cgroup':
mm/page_cgroup.c:111: error: implicit declaration of function 'vmalloc_node'
mm/page_cgroup.c:111: warning: assignment makes pointer from integer without a cast
mm/page_cgroup.c: In function '__free_page_cgroup':
mm/page_cgroup.c:140: error: implicit declaration of function 'vfree'
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (53 commits)
powerpc: Support for relocatable kdump kernel
powerpc: Don't use a 16G page if beyond mem= limits
powerpc: Add del_node() for early boot code to prune inapplicable devices.
powerpc: Further compile fixup for STRICT_MM_TYPECHECKS
powerpc: Remove empty #else from signal_64.c
powerpc: Move memory size print into common show_cpuinfo for 32-bit
hvc_console: Remove __devexit annotation of hvc_remove()
hvc_console: Add support for tty window resizing
hvc_console: Fix loop if put_char() returns 0
hvc_console: Add tty driver flag TTY_DRIVER_RESET_TERMIOS
hvc_console: Add a hangup notifier for backends
powerpc/83xx: Add DS1339 RTC support for MPC8349E-mITX boards .dts
powerpc/83xx: Add support for MCU microcontroller in .dts files
powerpc/85xx: Move mpc8572ds.dts to address-cells/size-cells = <2>
of/spi: Support specifying chip select as active high via device tree
powerpc: Remove device_type = "board_control" properties in .dts files
i2c-cpm: Suppress autoprobing for devices
powerpc/85xx: Fix mpc8536ds dma interrupt numbers
powerpc/85xx: Enable enhanced functions for 8536 TSEC
powerpc: Delete unused prom_strtoul and prom_memparse
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dvrabel/uwb
* 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/dvrabel/uwb: (47 commits)
uwb: wrong sizeof argument in mac address compare
uwb: don't use printk_ratelimit() so often
uwb: use kcalloc where appropriate
uwb: use time_after() when purging stale beacons
uwb: add credits for the original developers of the UWB/WUSB/WLP subsystems
uwb: add entries in the MAINTAINERS file
uwb: depend on EXPERIMENTAL
wusb: wusb-cbaf (CBA driver) sysfs ABI simplification
uwb: document UWB and WUSB sysfs files
uwb: add symlinks in sysfs between radio controllers and PALs
uwb: dont tranmit identification IEs
uwb: i1480/GUWA100U: fix firmware download issues
uwb: i1480: remove MAC/PHY information checking function
uwb: add Intel i1480 HWA to the UWB RC quirk table
uwb: disable command/event filtering for D-Link DUB-1210
uwb: initialize the debug sub-system
uwb: Fix handling IEs with empty IE data in uwb_est_get_size()
wusb: fix bmRequestType for Abort RPipe request
wusb: fix error path for wusb_set_dev_addr()
wusb: add HWA host controller driver
...
|
|
* 'for-next' of git://git.o-hand.com/linux-mfd:
mfd: check for platform_get_irq() return value in sm501
mfd: use pci_ioremap_bar() in sm501
mfd: Don't store volatile bits in WM8350 register cache
mfd: don't export wm3850 static functions
mfd: twl4030-gpio driver
mfd: rtc-twl4030 driver
mfd: twl4030 IRQ handling update
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/ehca: Reject dynamic memory add/remove when ehca adapter is present
IB/ehca: Fix reported max number of QPs and CQs in systems with >1 adapter
IPoIB: Set netdev offload features properly for child (VLAN) interfaces
IPoIB: Clean up ethtool support
mlx4_core: Add Ethernet PCI device IDs
mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC
mlx4_core: Multiple port type support
mlx4_core: Ethernet MAC/VLAN management
mlx4_core: Get ethernet MTU and default address from firmware
mlx4_core: Support multiple pre-reserved QP regions
Update NetEffect maintainer emails to Intel emails
RDMA/cxgb3: Remove cmid reference on tid allocation failures
IB/mad: Use krealloc() to resize snoop table
IPoIB: Always initialize poll_timer to avoid crash on unload
IB/ehca: Don't allow creating UC QP with SRQ
mlx4_core: Add QP range reservation support
RDMA/ucma: Test ucma_alloc_multicast() return against NULL, not with IS_ERR()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
sata_via: load DEVICE register when CTL changes
libata: set device class to NONE if phys_offline
libata-eh: fix slave link EH action mask handling
libata: transfer EHI control flags to slave ehc.i
libata-sff: fix ata_sff_post_internal_cmd()
libata: initialize port_task when !CONFIG_ATA_SFF
|
|
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] clps711x: add sparsemem definitions
[ARM] 5315/1: Fix section mismatch warning (sa1111)
[ARM] Orion: activate workaround for 88f6183 SPI clock erratum
[ARM] Orion: instantiate the dsa switch driver
[ARM] mv78xx0: force link speed/duplex on eth2/eth3
[ARM] remove extra brace in arch/arm/mach-pxa/trizeps4.c
[ARM] balance parenthesis in header file
[ARM] pxa: fix trizeps PCMCIA build
[ARM] pxa: fix trizeps defconfig
[ARM] dmabounce requires ZONE_DMA
[ARM] 5303/1: period_cycles should be greater than 1
[ARM] 5310/1: Fix cache flush functions for ARMv4
[ARM] pxa: fix 3bca103a1e658d23737d20e1989139d9ca8973bf
[ARM] pxa: fix redefinition of NR_IRQS
[ARM] S3C24XX: Fix redefine of DEFINE_TIMER() in s3c24xx pwm-clock.c
[ARM] S3C2443: Fix HCLK rate
[ARM] S3C24XX: Serial driver debug depends on DEBUG_LL
[ARM] S3C24XX: pwm-clock set_parent mask fix
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6: (41 commits)
[IA64] Fix annoying IA64_TR_ALLOC_MAX message.
[IA64] kill sys32_pipe
[IA64] remove sys32_pause
[IA64] Add Variable Page Size and IA64 Support in Intel IOMMU
ia64/pv_ops: paravirtualized instruction checker.
ia64/xen: a recipe for using xen/ia64 with pv_ops.
ia64/pv_ops: update Kconfig for paravirtualized guest and xen.
ia64/xen: preliminary support for save/restore.
ia64/xen: define xen machine vector for domU.
ia64/pv_ops/xen: implement xen pv_time_ops.
ia64/pv_ops/xen: implement xen pv_irq_ops.
ia64/pv_ops/xen: define the nubmer of irqs which xen needs.
ia64/pv_ops/xen: implement xen pv_iosapic_ops.
ia64/pv_ops/xen: paravirtualize entry.S for ia64/xen.
ia64/pv_ops/xen: paravirtualize ivt.S for xen.
ia64/pv_ops/xen: paravirtualize DO_SAVE_MIN for xen.
ia64/pv_ops/xen: define xen paravirtualized instructions for hand written assembly code
ia64/pv_ops/xen: define xen pv_cpu_ops.
ia64/pv_ops/xen: define xen pv_init_ops for various xen initialization.
ia64/pv_ops/xen: elf note based xen startup.
...
|
|
VIA controllers clear DEVICE register when IEN changes. Make sure
DEVICE is updated along with CTL.
This change is separated from Joseph Chan's larger patch.
http://thread.gmane.org/gmane.linux.kernel.commits.mm/40640
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Joseph Chan <JosephChan@via.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Reset methods don't have access to phys link status for slave links
and may incorrectly indicate device presence causing unnecessary probe
failures for unoccupied links. This patch clears device class to NONE
during post-reset processing if phys link is offline.
As on/offlineness semantics is strictly defined and used in multiple
places by the core layer, this won't change behavior for drivers which
don't use slave links.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Slave link action mask is transferred to master link and all the EH
actions are taken by the master link. ata_eh_about_to_do() and
ata_eh_done() are called with ATA_EH_ALL_ACTIONS to clear the slave
link actions during transfer. This always sets ATA_PFLAG_RECOVERED
flag causing spurious "EH complete" messages.
Don't set ATA_PFLAG_RECOVERED for slave link actions.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
ATA_EHI_NO_AUTOPSY and ATA_EHI_QUIET are used to control the behavior
of EH. As only the master link is visible outside EH, these flags are
set only for the master link although they should also apply to the
slave link, which causes spurious EH messages during probe and
suspend/resume.
This patch transfers those two flags to slave ehc.i before performing
slave autopsy and reporting.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
ata_sff_post_internal_cmd() needs to grab port lock before calling
ata_bmdma_stop() and also need to clear hsm_task_state. Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
ap->port_task was not initialized if !CONFIG_ATA_SFF later triggering
lockdep warning. Make sure it's initialized.
Reported by Larry Finger.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
for-next
|
|
Since the ehca device driver does not support dynamic memory add and
remove operations, the driver must explicitly reject such requests in
order to prevent unpredictable behaviors related to existing memory
regions that cover all of memory being used by InfiniBand protocols in
the kernel.
The solution (for now at least) is to add a memory notifier to the
ehca device driver and if a request for dynamic memory add or remove
comes in, ehca will always reject it. The user can add or remove
memory by hot-removing the ehca adapter, performing the memory
operation, and then hot-adding the ehca adapter back.
Signed-off-by: Stefan Roscher <stefan.roscher@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Because ehca adapters can differ in the maximum number of QPs and CQs
we have to save the maximum number of these ressources per adapter and
not globally per ehca driver. This fix introduces 2 new members to the
shca structure to store the maximum value for QPs and CQs per adapter.
The module parameters are now used as initial values for those
variables. If a user selects an invalid number of CQs or QPs we don't
print an error any longer, instead we will inform the user with a
warning and set the values to the respective maximum supported by the
HW.
Signed-off-by: Stefan Roscher <stefan.roscher@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Child devices were created without any offload features set, fix this by
moving the code that computes the features into generic function which is
now called through non-child and child device creation.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
-- v1 has a bug where the 'result' flag in ipoib_vlan_add may be used uninitialized
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Add a get_rx_csum method. Remove the driver's own get_tso method, as
the ethtool kernel code uses the default one if nothing is provided.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The Mellanox ConnectX can operate as an InfiniBand adapter, as an
Ethernet NIC, or as a Fibre Channel (FC) HBA. The kernel has a
low-level driver, mlx4_core, which handles multiplexing access to the
device, and there is also already an InfiniBad driver, mlx4_ib.
This patch adds a new driver, mlx4_en, which implements a standard
Ethernet NIC driver.
Signed-off-by: Liran Liss <liranl@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Multi-protocol adapters support different port types. Each consumer
of mlx4_core queries for supported port types; in particular mlx4_ib
can no longer assume that all physical ports belong to it. Port type
is configured through a sysfs interface. When the type of a port is
changed, all mlx4 interfaces are unregistered, and then registered
again with the new port types.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Add support for managing MAC and VLAN filters for each port.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Oren Duer <oren@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Get maximum ethernet MTU and default MAC address from the firmware
QUERY_DEV_CAP command.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
For ethernet support, we need to reserve QPs for the ethernet and
fibre channel driver. The QPs are reserved at the end of the QP
table. (This way we assure that they are aligned to their size)
We need to consider these reserved ranges in bitmap creation, so we
extend the mlx4 bitmap utility functions to allow reserved ranges at
both the bottom and the top of the range.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
This adds relocatable kernel support for kdump. With this one can
use the same regular kernel to capture the kdump. A signature (0xfeed1234)
is passed in r6 from panic code to the next kernel through kexec_sequence
and purgatory code. The signature is used to differentiate between
kdump kernel and non-kdump kernels.
The purgatory code compares the signature and sets the __kdump_flag in
head_64.S. During the boot up, kernel code checks __kdump_flag and if it
is set, the kernel will behave as relocatable kdump kernel. This kernel
will boot at the address where it was loaded by kexec-tools ie. at the
address reserved through crashkernel boot parameter.
CONFIG_CRASH_DUMP depends on CONFIG_RELOCATABLE option to build kdump
kernel as relocatable. So the same kernel can be used as production and
kdump kernel.
This patch incorporates the changes suggested by Paul Mackerras to avoid
GOT use and to avoid two copies of the code.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Mohan Kumar M <mohan@in.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
If mem= is used on the boot command line to limit memory then the memory block where a 16G page resides may not be available.
Thanks to Michael Ellerman for finding the problem.
Signed-off-by: Jon Tollefson <kniht@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Some platforms have variants that can share most of a flat device tree but need
a few devices selectively pruned at boot time. This adds del_node() to ops.h
to allow access to the existing fdt_del_node().
Signed-off-by: Mike Ditto <mditto@consentry.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
A patch of mine was recently committed to fix up STRICT_MM_TYPECHECKS
behaviour on powerpc (f5ea64dcbad89875d130596df14c9b25d994a737).
However, something which breaks it again seems to have slipped in
afterwards. So, here's another small fix.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Remove empty/bogus #else from signal_64.c
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Most of the platforms were printing the size of the memory
in their show_cpuinfo implementations. This moves that to
the common show_cpuinfo, so that all 32-bit platforms will
now print the size of memory. I also update the code
to deal with the fact that total_memory is now a phys_addr_t.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Removed __devexit annotation of hvc_remove() to avoid a section mismatch
if the backend initialization fails and hvc_remove() must be used to
clean up allocated hvc structs (called in section __init or __devinit).
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The patch provides the hvc_resize() function to update the terminal
window dimensions (struct winsize) for a specified hvc console.
The function stores the new window size and schedules a function
that finally updates the tty winsize and signals the change to
user space (SIGWINCH).
Because the winsize update must acquire a mutex and might sleep,
the function is scheduled instead of being called from hvc_poll()
or khvcd.
This patch uses the tty_do_resize() routine from the tty layer.
A pending resize work is canceled in hvc_close() and hvc_hangup().
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
If put_char() routine of a hvc console backend returns 0, then the
hvc console starts looping in the following scenarios:
1. hvc_console_print()
If put_char() returns 0 then the while loop may loop forever.
I have added the missing check for 0 to throw away console messages.
2. khvcd may loop:
The thread calls hvc_poll() --> hvc_push()... if there are still
buffered data then the HVC_POLL_WRITE bit is set and causes the
khvcd thread to loop (if yield() returns immediately).
However, instead of looping, the khvcd thread could sleep for
MIN_TIMEOUT (doing the same as for get_chars()).
The MIN_TIMEOUT is set if hvc_push() was not able to write
data to the backend. If data has been written, the timeout is
set to 0 to immediately re-schedule hvc_poll().
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com> (virtio_console)
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
After a tty hangup() or close() operation, processes might not reset the
termio settings to a sane state. In order to reset the termios to its
default settings the tty driver flag TTY_DRIVER_RESET_TERMIOS has been added.
TTY driver flag description from include/linux/tty_driver.h:
TTY_DRIVER_RESET_TERMIOS --- requests the tty layer to reset the
termios setting when the last process has closed the device.
Used for PTY's, in particular.
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
I have added a hangup notifier that can be used by hvc console
backends to handle a tty hangup. The default irq hangup notifier
calls the notifier_del_irq() for compatibility.
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
sm501_devdata->irq is unsigned, while platform_get_irq() returns a
signed int.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
|
|
Use the newly introduced pci_ioremap_bar() function in drivers/mfd.
pci_ioremap_bar() just takes a pci device and a bar number, with the goal
of making it really hard to get wrong, while also having a central place
to stick sanity checks.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
|
|
This makes the contents of the cache clearer and fixes incorrect
initialisation of the cache for partially volatile registers.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
|
|
October 10th linux-next build (powerpc allyesconfig) failed like this:
drivers/mfd/wm8350-core.c:1131: error: __ksymtab_wm8350_create_cache causes a section type conflict
Caused by commit 89b4012befb1abca5e86d232bc0e2a797b0d9825 ("mfd: Core
support for the WM8350 AudioPlus PMIC"). wm8350_create_cache is not used
elsewhere, so remove the EXPORT_SYMBOL.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
|
|
This adds basic support for the GPIOs in the twl4030 power management
chip. That includes two open drain LED drivers, and the use of GPIO-0
(and GPIO-1) as MMC/SD card detect switches which can control whether
the VMMC1 (and VMMC2) regulators are active.
This version of the code has a debounce call that will probably be
replaced before long, when a more generic interface exists.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
|
|
This adds a driver for the RTC inside the TWL4030 multi-function device.
It's a fairly basic RTC, with a wake-capable alarm.
Note that many of the pre-release Overo boards now in circulation can't
effectively use this RTC, because of a wiring error that puts its TWL
chip into "secure" mode. (As in "secure yourself against tampering".)
This isn't an issue on other OMAP3 boards now supported in mainline,
such as Beagle and Labrador.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
|
|
- Move it into a separate file; clean and streamline it
- Restructure the init code for reuse during secondary dispatch
- Support both levels (primary, secondary) of IRQ dispatch
- Use a workqueue for irq mask/unmask and trigger configuration
Code for two subchips currently share that secondary handler code.
One is the power subchip; its IRQs are now handled by this core,
courtesy of this patch. The other is the GPIO module, which will
be supported through a later patch.
There are also minor changes to the header file, mostly related
to GPIO support; nothing yet in mainline cares about those. A
few references to OMAP-specific symbols are disabled; when they
can all be removed, the TWL4030 support ceases being OMAP-specific.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
|
|
Fix the edb7211_defconfig build errors.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch fixes the section mismatch warning from
sa1111.o at buildtime.
CC arch/arm/common/sa1111.o
LD arch/arm/common/built-in.o
LD vmlinux.o
MODPOST vmlinux.o
WARNING: vmlinux.o(.text+0x87f4): Section mismatch in reference from the function sa1111_probe() to the function .devinit.text:sa1110_mb_enable()
The function sa1111_probe() references
the function __devinit sa1110_mb_enable().
This is often because sa1111_probe lacks a __devinit
annotation or the annotation of sa1110_mb_enable is wrong.
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Manual merge of:
arch/powerpc/Kconfig
arch/powerpc/include/asm/page.h
|
|
|
|
The RTC is sitting on the I2C2 bus at address 0x68. RTC interrupt signal
is connected to the IPIC's EXT2 interrupt line, the line is shared with
Vitesse 8201 Ethernet PHY.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
MCU is an external Freescale MC9S08QG8 microcontroller, mainly used to
provide soft power-off function, but also exports two GPIOs (wired to
the LEDs and also available from the external headers).
Added the MCU on mpc8349emitx, mpc837xrdb and mpc8315erdb boards.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
