| Age | Commit message (Collapse) | Author |
|---|
|
Add a load option to intel-rng to allow skipping the FWH detection,
necessary in case the BIOS has locked read-only the firmware hub space.
Also prevent any attempt to write to firmware space if it cannot be write
enabled (apparently caused hangs on some systems not having an FWH and thus
also not having a respective RNG).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Revert bd_mount_mutex back to a semaphore so that xfs_freeze -f /mnt/newtest;
xfs_freeze -u /mnt/newtest works safely and doesn't produce lockdep warnings.
(XFS unlocks the semaphore from a different task, by design. The mutex
code warns about this)
Signed-off-by: Dave Chinner <dgc@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Fix void cast and re-enable on sparc.
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
NFS: Fix race in nfs_release_page()
invalidate_inode_pages2() may find the dirty bit has been set on a page
owing to the fact that the page may still be mapped after it was locked.
Only after the call to unmap_mapping_range() are we sure that the page
can no longer be dirtied.
In order to fix this, NFS has hooked the releasepage() method and tries
to write the page out between the call to unmap_mapping_range() and the
call to remove_mapping(). This, however leads to deadlocks in the page
reclaim code, where the page may be locked without holding a reference
to the inode or dentry.
Fix is to add a new address_space_operation, launder_page(), which will
attempt to write out a dirty page without releasing the page lock.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Also, the bare SetPageDirty() can skew all sort of accounting leading to
other nasties.
[akpm@osdl.org: cleanup]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This adds the profile=kvm boot option, which enables KVM to profile VM
exits.
Use: "readprofile -m ./System.map | sort -n" to see the resulting
output:
[...]
18246 serial_out 148.3415
18945 native_flush_tlb 378.9000
23618 serial_in 212.7748
29279 __spin_unlock_irq 622.9574
43447 native_apic_write 2068.9048
52702 enable_8259A_irq 742.2817
54250 vgacon_scroll 89.3740
67394 ide_inb 6126.7273
79514 copy_page_range 98.1654
84868 do_wp_page 86.6000
140266 pit_read 783.6089
151436 ide_outb 25239.3333
152668 native_io_delay 21809.7143
174783 mask_and_ack_8259A 783.7803
362404 native_set_pte_at 36240.4000
1688747 total 0.5009
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
md raidX make_request functions strip off the BIO_RW_SYNC flag, thus
introducing additional latency.
Fixing this in raid1 and raid10 seems to be straightforward enough.
For our particular usage case in DRBD, passing this flag improved some
initialization time from ~5 minutes to ~5 seconds.
Acked-by: NeilBrown <neilb@suse.de>
Signed-off-by: Lars Ellenberg <lars@linbit.com>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
o sched_clock() a non-init function is using init data tsc_disable. This
is flagged by MODPOST on i386 if CONFIG_RELOCATABLE=y
WARNING: vmlinux - Section mismatch: reference to .init.data:tsc_disable from .text between 'sched_clock' (at offset 0xc0109d58) and 'tsc_update_callback'
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
o Kdump documentation update.
- Update details for using relocatable kernel.
- Start using kexec-tools-testing release as it is latest and old
kexec-tools can't load relocatable bzImage file.
- Also add kdump on ia64 specific details.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Horms <horms@verge.net.au>
Cc: Mohan Kumar M <mohan@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Compiling the kernel with CONFIG_HOTPLUG = y and CONFIG_HOTPLUG_CPU = n
with CONFIG_RELOCATABLE = y generates the following modpost warnings
WARNING: vmlinux - Section mismatch: reference to .init.data: from
.text between '_cpu_up' (at offset 0xc0141b7d) and 'cpu_up'
WARNING: vmlinux - Section mismatch: reference to .init.data: from
.text between '_cpu_up' (at offset 0xc0141b9c) and 'cpu_up'
WARNING: vmlinux - Section mismatch: reference to .init.text:__cpu_up
from .text between '_cpu_up' (at offset 0xc0141bd8) and 'cpu_up'
WARNING: vmlinux - Section mismatch: reference to .init.data: from
.text between '_cpu_up' (at offset 0xc0141c05) and 'cpu_up'
WARNING: vmlinux - Section mismatch: reference to .init.data: from
.text between '_cpu_up' (at offset 0xc0141c26) and 'cpu_up'
WARNING: vmlinux - Section mismatch: reference to .init.data: from
.text between '_cpu_up' (at offset 0xc0141c37) and 'cpu_up'
This is because cpu_up, _cpu_up and __cpu_up (in some architectures) are
defined as __devinit
AND
__cpu_up calls some __cpuinit functions.
Since __cpuinit would map to __init with this kind of a configuration,
we get a .text refering .init.data warning.
This patch solves the problem by converting all of __cpu_up, _cpu_up
and cpu_up from __devinit to __cpuinit. The approach is justified since
the callers of cpu_up are either dependent on CONFIG_HOTPLUG_CPU or
are of __init type.
Thus when CONFIG_HOTPLUG_CPU=y, all these cpu up functions would land up
in .text section, and when CONFIG_HOTPLUG_CPU=n, all these functions would
land up in .init section.
Tested on a i386 SMP machine running linux-2.6.20-rc3-mm1.
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This fixes the SH rtc driver to
(a) correctly report 'enabled' status with other alarm status;
(b) not duplicate that status in its procfs dump
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Back out the recent fix for this bug, fix it by correctly initialising
ConfigInfoView.sym.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: "Cyrill V. Gorcunov" <gorcunov@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Fix an oops experienced on the Cell architecture when init-time functions,
early_*(), are called at runtime. It alters the call paths to make sure
that the callers explicitly say whether the call is being made on behalf of
a hotplug even, or happening at boot-time.
It has been compile tested on ppc64, ia64, s390, i386 and x86_64.
Acked-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Acked-by: Andy Whitcroft <apw@shadowen.org>
Cc: Christoph Lameter <clameter@engr.sgi.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
While testing 2.6.20-rc3 on a machine with some CK804 chipsets, we noticed
that quirk_nvidia_ck804_msi_ht_cap() was not detecting HT MSI capabilities
anymore. It is actually caused by the MSI mapping on the root chipset
being the 2nd HT capability in the chain. pci_find_ht_capability() does
not seem to find anything but the first HT cap correctly, because it
forgets to increment the position before looking for the next cap. The
following patch seems to fix it.
At least, this proves that having a ttl is good idea since the machine
would have been stucked in an infinite loop if we didn't have a ttl :)
We have to pass pos + PCI_CAP_LIST_NEXT to __pci_find_next_cap_ttl to
get the next HT cap instead of the same one again.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Andrew J. Gallatin <gallatin@myri.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Commit 5c1e176781f43bc902a51e5832f789756bff911b ("sched: force /sbin/init
off isolated cpus") sets init's cpus_allowed to a subset of cpu_online_map
at boot time, which means that tasks won't be scheduled on cpus that are
added to the system later.
Make init's cpus_allowed a subset of cpu_possible_map instead. This should
still preserve the behavior that Nick's change intended.
Thanks to Giuliano Pochini for reporting this and testing the fix:
http://ozlabs.org/pipermail/linuxppc-dev/2006-December/029397.html
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
It might save a few bytes after bootup, but it causes the string to be
linked in at the end of the final vmlinux image, which defeats the whole
point of doing all this, namely allowing some broken user-space binaries
to search for the kernel version string in the kernel binary.
So just remove the __init specifier.
Cc: Olaf Hering <olaf@aepfle.de>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Andrey Borzenkov <arvidjaar@mail.ru>
Cc: Andrew Morton <akpm@osdl.org>
Acked-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
* 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6:
[PATCH] x86-64: Fix warnings in ia32_aout.c
[PATCH] i386: Convert some functions to __init to avoid MODPOST warnings
[PATCH] i386: Fix memory hotplug related MODPOST generated warning
[PATCH] x86-64: tighten up printks
[PATCH] x86-64: - Ignore long SMI interrupts in clock calibration
[PATCH] x86-64: pci quirks MODPOST warning fix
[PATCH] x86-64: Modpost whitelist reference to more symbols (pattern 3)
[PATCH] x86-64: modpost add more symbols to whitelist pattern2
[PATCH] i386: make apic probe function non-init
[PATCH] i386: cpu hotplug/smpboot misc MODPOST warning fixes
[PATCH] x86-64: Use different constraint for gcc < 4.1 in bitops.h
[PATCH] x86-64: Make noirqdebug_setup function non init to fix modpost warning
[PATCH] i386: Update defconfig
[PATCH] x86-64: Update defconfig
|
|
Fix
linux/arch/x86_64/ia32/ia32_aout.c: In function ‘create_aout_tables’:
linux/arch/x86_64/ia32/ia32_aout.c:244: warning: cast from pointer to integer of different size
linux/arch/x86_64/ia32/ia32_aout.c:253: warning: cast from pointer to integer of different size
with gcc 4.3
Signed-off-by: Andi Kleen <ak@suse.de>
|
|
o Some functions which should have been in init sections as they are called
only once. Put them in init sections. Otherwise MODPOST generates warning
as these functions are placed in .text and they end up accessing something
in init sections.
WARNING: vmlinux - Section mismatch: reference to .init.text:migration_init
from .text between 'do_pre_smp_initcalls' (at offset 0xc01000d1) and
'run_init_process'
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andi Kleen <ak@suse.de>
|
|
o Fix modpost generated warning.
WARNING: vmlinux - Section mismatch: reference to .init.text: from .text
between 'add_one_highpage_hotplug' (at offset 0xc0113d3f) and 'online_page'
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andi Kleen <ak@suse.de>
|
|
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
|
|
Ensure that no SMI interrupts occur between the read of the HPET & TSC
in the clock calibration loop.
I noticed that a 2.66GHz system incorrectly detected the processor
clock speed about 1/7 of the time:
time.c: Detected 2660.005 MHz processor. (most of the time)
time.c: Detected 2988.203 MHz processor. (sometime)
The problem is caused by an SMI interrupt occuring in hpet_calibrate_tsc()
between the read of the HPET & TSC. Prior to switching the BIOS into
ACPI mode, it appears that every 27msec an SMI interrupt occurs. The
SMI interrupt takes 4.8 msec to process.
Note: On my test system, TICK_MIN had to be >380. I picked 5000
to minimize risk of having a value that is too small for other
platforms.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andi Kleen <ak@suse.de>
arch/x86_64/kernel/time.c | 25 +++++++++++++++++++++----
1 file changed, 21 insertions(+), 4 deletions(-)
|
|
o MODPOST generates warnings for i386 if kernel is compiled with
CONFIG_RELOCATABLE=y
WARNING: vmlinux - Section mismatch: reference to .init.data: from .text between 'asus_hides_smbus_lpc_ich6' (at offset 0xc0217d58) and 'quirk_cardbus_legacy'
WARNING: vmlinux - Section mismatch: reference to .init.data: from .text between 'asus_hides_smbus_lpc' (at offset 0xc0217fd9) and 'pci_match_id'
o Two quirk functions which are non __init, are accessing data which is
of type __init.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
|
|
o MODPOST generates warning on i386 if kernel is compiled with
CONFIG_RELOCATABLE=y.
WARNING: vmlinux - Section mismatch: reference to .init.text:__init_begin from .text between 'free_initmem' (at offset 0xc0114fd3) and 'do_test_wp_bit'
WARNING: vmlinux - Section mismatch: reference to .init.text:_sinittext from .text between 'core_kernel_text' (at offset 0xc012aeae) and 'kernel_text_address'
WARNING: vmlinux - Section mismatch: reference to .init.text:_einittext from .text between 'core_kernel_text' (at offset 0xc012aeb7) and 'kernel_text_address'
WARNING: vmlinux - Section mismatch: reference to .init.text:_sinittext from .text between 'get_symbol_pos' (at offset 0xc0135776) and 'reset_iter'
WARNING: vmlinux - Section mismatch: reference to .init.text:_einittext from .text between 'get_symbol_pos' (at offset 0xc013577d) and 'reset_iter'
o These symbols (__init_begin, _sinittext, _einittext) belong to init
section and generally represent a section boundary. These are special
symbols in the sense that their size is zero and no memory is allocated
for them in init section. Their addr and value are same. So even if
we free the init section, it is ok to reference them.
o Whitelist access to such select symbols in MODPOST.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
|
|
o MODPOST generates warning for i386 if compiled with CONFIG_RELOCATABLE=y
and serial console support is enabled.
o Serial console setup function, serial8250_console_setup(), is a non __init
function and it calls functions which are of type __init().
(uart_parse_options() and uart_set_options()). Assuming, setup will
be called during init time, changing serial8250_console_setup() to __init.
o Adding one more pattern to modpost whitelist. Console drivers might
have *_console structures containing references to setup functions which
can be of __init type. Don't generate warnings for those.
WARNING: vmlinux - Section mismatch: reference to .init.text: from .data between 'serial8250_console' (at offset 0xc05a33d8) and 'serial8250_reg'
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
|
|
o struct genapic contains pointer to probe() function which is of type
__init. Hence MODPOST generates warning if kernel is compiled with
CONFIG_RELOCATABLE=y for i386.
WARNING: vmlinux - Section mismatch: reference to .init.text: from .data between 'apic_summit' (at offset 0xc058b504) and 'apic_bigsmp'
WARNING: vmlinux - Section mismatch: reference to .init.text: from .data between 'apic_bigsmp' (at offset 0xc058b5a4) and 'cpu.4471'
WARNING: vmlinux - Section mismatch: reference to .init.text: from .data between 'apic_es7000' (at offset 0xc058b644) and 'apic_default'
WARNING: vmlinux - Section mismatch: reference to .init.text: from .data between 'apic_default' (at offset 0xc058b6e4) and 'interrupt'
o One of the possible options is to put special case check in MODPOST to
not emit warnings for this case but I think it is not a very good option
in terms of maintenance.
o Another option is to make probe() function non __init. Anyway this function
is really small so not freeing this memory after init is not a big deal.
Secondly, from a programming perspective, probably genapic should not
provide pointers to functions which have been freed as genapic is non
__init and is used even after initialization is complete.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
|
|
o Misc smpboot/cpu hotplug path cleanups. I did those to supress the
warnings generated by MODPOST. These warnings are visible only
if CONFIG_RELOCATABLE=y.
o CONFIG_RELOCATABLE compiles the kernel with --emit-relocs option. This
option retains relocation information in vmlinux file and MODPOST
is quick to spit out "Section mismatch" warnings.
o This patch fixes some of those warnings. Many of the functions in
smpboot case are __devinit type and they in turn accesses text/data which
if of type __cpuinit. Now if CONFIG_HOTPLUG=y and CONFIG_HOTPLUG_CPU=n
then we end up in cases where a function in .text segment is calling
another function in .init.text segment and MODPOST emits warning.
WARNING: vmlinux - Section mismatch: reference to .init.text:identify_cpu from .text between 'smp_store_cpu_info' (at offset 0xc011020d) and 'do_boot_cpu'
WARNING: vmlinux - Section mismatch: reference to .init.text:init_gdt from .text between 'do_boot_cpu' (at offset 0xc01102ca) and '__cpu_up'
WARNING: vmlinux - Section mismatch: reference to .init.text:print_cpu_info from .text between 'do_boot_cpu' (at offset 0xc01105d0) and '__cpu_up'
o It also fixes the issues where CONFIG_HOTPLUG_CPU=y and start_secondary()
is calling smp_callin() which in-turn calls synchronize_tsc_ap() which is
of type __init. This should have meant broken CPU hotplug.
WARNING: vmlinux - Section mismatch: reference to .init.data: from .text between 'start_secondary' (at offset 0xc011603f) and 'initialize_secondary'
WARNING: vmlinux - Section mismatch: reference to .init.data: from .text between 'MP_processor_info' (at offset 0xc0116a4f) and 'mp_register_lapic'
WARNING: vmlinux - Section mismatch: reference to .init.data: from .text between 'MP_processor_info' (at offset 0xc0116a4f) and 'mp_register_lapic'
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andi Kleen <ak@suse.de>
|
|
+m is really correct for a RMW instruction, but some older gccs
error out. I finally gave in and ifdefed it.
This fixes compilation errors with some compiler version.
Signed-off-by: Andi Kleen <ak@suse.de>
|
|
o noirqdebug_setup() is __init but it is being called by
quirk_intel_irqbalance() which if of type __devinit. If CONFIG_HOTPLUG=y,
quirk_intel_irqbalance() is put into text section and it is wrong to
call a function in __init section.
o MODPOST flags this on i386 if CONFIG_RELOCATABLE=y
WARNING: vmlinux - Section mismatch: reference to .init.text:noirqdebug_setup from .text between 'quirk_intel_irqbalance' (at offset 0xc010969e) and 'i8237A_suspend'
o Make noirqdebug_setup() non-init.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
|
|
Signed-off-by: Andi Kleen <ak@suse.de>
|
|
Signed-off-by: Andi Kleen <ak@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
ieee1394: sbp2: fix probing of some DVD-ROM/RWs
|
|
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Alchemy: Fix PCI-memory access
[MIPS] Fix N32 SysV IPC routines
[MIPS] PNX8550: Fix system timer initialization
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
MMC: at91 mmc linkage updates
ARM: OMAP: fix MMC workqueue changes
|
|
The problem was introduced in 2.6.18.3 with the casting of some
36bit-defines (PCI memory) in au1000.h to resource_size_t which may be
u32 or u64 depending on the experimental CONFIG_RESOURCES_64BIT.
With unset CONFIG_RESOURCES_64BIT, the pci-memory cannot be accessed
because the ioremap in arch/mips/au1000/common/pci.c already used the
truncated addresses.
With set CONFIG_RESOURCES_64BIT, things get even worse, because PCI-scan
aborts, due to resource conflict: request_resource() in arch/mips/pci/pci.c
fails because the maximum iomem-address is 0xffffffff (32bit) but the
pci-memory-start-address is 0x440000000 (36bit).
To get pci working again, I propose the following patch:
1. remove the resource_size_t-casting from au1000.h again
2. make the casting in arch/mips/au1000/common/pci.c (it's allowed and
necessary here. The 36bit-handling will be done in __fixup_bigphys_addr).
With this patch pci works again like in 2.6.18.2, the gcc-compile warnings
in pci.c are gone and it doesn't depend on CONFIG_EXPERIMENTAL.
Signed-off-by: Alexander Bigga <ab@mycable.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
|
|
Add wrappers for N32 msg{snd,rcv}. compat_sys_msg{snd,rcv} can not not be
used as system call entries as is. This fix is based on Kaz Kylheku's
patch.
Also change a type of last argument of sysn32_semctl to match its true
size.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Since commit 98e238cd42be6c0852da519303cf0182690f8d9f in Linux 2.6.19,
"ieee1394: sbp2: don't prefer MODE SENSE 10", some FireWire DVD-ROMs and
DVD-RWs were mistaken as CD-ROM because sr_mod now sent MODE SENSE 6.
The MMC command set includes only MODE SENSE 10.
http://bugzilla.kernel.org/show_bug.cgi?id=7800
This fix lets sbp2 switch scsi_device.use_10_for_rw on for MMC LUs.
This should rather be done in the command set driver sr_mod, not in the
sbp2 transport driver, and an according patch will follow for a next
Linux release.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Revert previous attempts at messing with the linux banner string and
simply use a separate format string for proc.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Acked-by: Olaf Hering <olaf@aepfle.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: Andrey Borzenkov <arvidjaar@mail.ru>
Cc: Andrew Morton <akpm@osdl.org>
Cc: Andy Whitcroft <apw@shadowen.org>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[IPV4] devinet: inetdev_init out label moved after RCU assignment
[INET]: style updates for the inet_sock->is_icsk assignment fix
[SCTP]: Fix err_hdr assignment in sctp_init_cause.
[NETFILTER]: tcp conntrack: fix IP_CT_TCP_FLAG_CLOSE_INIT value
[NETFILTER]: nf_nat: fix hanging connections when loading the NAT module
[NETFILTER]: arp_tables: fix userspace compilation
[NETFILTER]: nf_conntrack_ipv6: fix crash when handling fragments
|
|
This patch adds myself as maintainer of the sata_promise
libata driver.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IB/mthca: Don't execute QUERY_QP firmware command for QP in RESET state
IB/ehca: Use proper GFP_ flags for get_zeroed_page()
IB/mthca: Fix PRM compliance problem in atomic-send completions
RDMA/ucma: Don't report events with invalid user context
RDMA/ucma: Fix struct ucma_event leak when backlog is full
RDMA/iwcm: iWARP connection timeouts shouldn't be reported as rejects
IB/iser: Return error code when PDUs may not be sent
IB/mthca: Fix off-by-one in FMR handling on memfree
|
|
inetdev_init out label moved after RCU assignment
(final suggestion by Herbert Xu)
Signed-off-by: Jarek Poplawski <jarkao2@o2.pl>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A quick patch to change the inet_sock->is_icsk assignment to better fit with
existing kernel coding style.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The subh->err_hdr should point to the error header, not the data.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IP_CT_TCP_FLAG_CLOSE_INIT is a flag and should have a value of 0x4 instead
of 0x3, which is IP_CT_TCP_FLAG_WINDOW_SCALE | IP_CT_TCP_FLAG_SACK_PERM.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When loading the NAT module, existing connection tracking entries don't
have room for NAT information allocated and packets are dropped, causing
hanging connections. They really should be entered into the NAT table
as NULL mappings, but the current allocation scheme doesn't allow this.
For now simply accept those packets to avoid the hanging connections.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The included patch translates arpt_counters to xt_counters, making
userspace arptables compile against recent kernels.
Signed-off-by: Bart De Schuymer <bdschuym@pandora.be>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When IPv6 connection tracking splits up a defragmented packet into
its original fragments, the packets are taken from a list and are
passed to the network stack with skb->next still set. This causes
dev_hard_start_xmit to treat them as GSO fragments, resulting in
a use after free when connection tracking handles the next fragment.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If a QP being queried is in the RESET state, don't execute the
QUERY_QP firmware command (because it will fail).
Signed-off-by: Dotan Barak <dotanb@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Here is a patch for ehca to use proper flag, ie. GFP_ATOMIC
resp. GFP_KERNEL, when calling get_zeroed_page() to prevent "Bug:
scheduling while atomic...". This error does not cause a kernel panic
but makes ipoib un-usable afterwards. It is reproducible on
2.6.20-rc4 if one does ifconfig down during a flood ping test. I have
not observed this error in earlier releases incl. 2.6.20-rc1.
This error occurs when a qp event/irq is received and ehca event
handler allocates a control block/page to obtain HCA error data block.
Use of GFP_ATOMIC when in interrupt context prevents this issue.
Signed-off-by Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
