| Age | Commit message (Collapse) | Author |
|---|
|
loop)
We now exit fw_send_phy_config /after/ the PHY config packet has been
transmitted, instead of before. A subsequent fw_core_initiate_bus_reset
will therefore not overlap with the transmission. This is meant to make
the send PHY config packet + reset bus routine more deterministic.
Fixes bus reset loop and eventual panic with
- VIA VT6307 + IOGEAR hub + Unibrain Fire-i camera
http://bugzilla.kernel.org/show_bug.cgi?id=10128
- JMicron card
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
|
|
request_generation is internal to fw-ohci and unneeded in fw_card.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
for code efficiency.
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Trivial change to replace more meaningless (to the untrained eye) hex
values with defined CSR constants.
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
When a device changes its configuration ROM, it announces this with a
bus reset. firewire-core has to check which node initiated a bus reset
and whether any unit directories went away or were added on this node.
Tested with an IOI FWB-IDE01AB which has its link-on bit set if bus
power is available but does not respond to ROM read requests if self
power is off. This implements
- recognition of the units if self power is switched on after fw-core
gave up the initial attempt to read the config ROM,
- shutdown of the units when self power is switched off.
Also tested with a second PC running Linux/ieee1394. When the eth1394
driver is inserted and removed on that node, fw-core now notices the
addition and removal of the IPv4 unit on the ieee1394 node.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
read_bus_info_block() is repeatedly called by workqueue jobs.
These will step on each others toes eventually if there are multiple
workqueue threads, and we end up with corrupt config ROM images.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
and more)
Unlike the ohci1394 driver, fw-ohci uses the selfIDGeneration field of
bus reset packets to determine the generation of incoming requests as
per OHCI 1.1 clause 8.4.2.3. This is more precise --- provided that the
controller inserts the correct generation. Texas Instruments chips
often don't.
This prevented the transmission of response packets, which for example
broke AV/C transactions as used when communicating with miniDV cameras
and any other AV/C devices.
There is apparently no way to detect and adjust incorrect generations.
Therefore we ignore the generation of bus reset packets from TI chips
and use the generation of the self ID buffer instead. Alas this is
received at a slightly wrong time. In rare cases, this could cause us
to not respond to legitimate requests or to respond to expired requests.
(The latter is less likely because the bus reset packet AR event is
typically handled before the self ID complete event.)
Bug reported by Mladen Kuntner, who was extraordinarily patient while
dealing with the driver maintainers. Fix confirmed to be required and
effective for TSB82AA2 and a TSB43AB22 or TSB43AB22A.
https://bugzilla.redhat.com/show_bug.cgi?id=243081
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
|
|
Extend the logging of "AR evt_bus_reset, link internal" to "AR
evt_bus_reset, generation ${selfIDGeneration}". That way we can check
whether this generation matches the one seen in self ID complete event
logging. See OHCI 1.1 clause 8.4.2.3.
Also extend logging of "firewire_ohci: * selfIDs, generation *" by
"local node ID ffc*" in self ID logging to make the local node in AT/AR
event logs more obvious.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
|
|
Add a debug option to watch bus reset interrupt events. Half of this
patch is taken from Jarod Wilson's first version of the JMicron fix.
BusReset interrupts are only generated if the respective module
parameter flag was set before the controller is being initialized.
Else we keep this event masked to reduce IRQ load in normal operation
and to avoid potential problems with buggy chips.
Note, this is unlike the other IRQ events whose logging can be enabled
any time after chip initialization. This and the influence on what
interrupts the chip generates is why I added an extra flag for it.
Also, reorder the debug parameter flags according to their perceived
usefulness.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
|
|
I finally tracked down the issues with this JMicron PCI-e card in my
possession to a failure to comply with section 7.2.3.2 of the OHCI 1.1
specification (thanks to Kristian for the pointer to illustrate that it
is indeed a flaw in this card, not the driver). The controller should
simply flush the packets we've appended to its AT queue if a bus reset
occurs before they've been transmitted and we'll try again, but
something goes wrong and the controller winds up hung.
However, we can avoid the problem by simply checking if the
IntEvent.busReset register had been set before we try appending to the
AT context. When busReset is set, the AT context is completely halted
until busReset is cleared, so there's no point in appending AT packets
until the register is cleared. So at_context_queue_packet() now checks
for busReset being set, and bails with an RCODE_GENERATION packet ack,
which results in us trying to append the packet again after recognizing
the fact there has been a bus reset, and clearing busReset.
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
While trying to debug this piece of crap JMicron PCI-e controller in my
possession, one thought was that perhaps I was encountering register access
failures. I'm not, but logging them would be good, so we can see if they
are a real problem we should be taking into account anywhere in the code.
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (added list contact)
|
|
I've now witnessed multiple occasions where one of my controllers (a very
poorly working JMicron PCIe card) fails to get its registers properly set
up in ohci_enable(), apparently due to an occasionally very slow to
initiate SClk. The easy fix for this problem is to add a tiny while loop
to try again a time or three after initially enabling LPS before we
move on (or give up).
Of course, the card still isn't fully functional yet, but this gets it at
least one tiny step closer...
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Balance ohci_pmac_on and ohci_pmac_off if pci_driver.probe fails.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
and make another expression more readable.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
This adds debug printks for asynchronous transmission and reception and
for self ID reception. They can be enabled at module load time, and at
runtime via /sys/module/firewire_ohci/parameters/debug.
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
Also added: Logging of interrupt event codes and of cancelled AT
packets.
The code now depends on a Kconfig variable. This makes it easier to
build firewire-ohci without the feature or to make it an option in the
future. The variable is currently hidden and always on.
This feature inflates firewire-ohci.ko by 7 kB = 27% on x86-64 and by
4 kB = 23% on i686.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
fw_core_handle_bus_reset() incorrectly relied on the assumption that
self_id_count > 0.
We check early in fw-ohci and discard the self ID complete event if
self_id_count == 0 because a valid event always has at least one self ID
packet in it (the one of the local node). Hence treat self_id_count ==
0 like any other kind of invalid self ID buffer.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
|
|
Discard self ID buffer contents if
- the selfIDError flag is set,
- any of the self ID packets has bit errors.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
|
|
Clean up shared code and variable names.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
The platform feature calls in the suspend method switched off cable
power, but the calls in the resume method did not switch it back on.
Add the necessary feature call to .resume. Also add the corresponding
call to .suspend to make .suspend's behavior explicitly the same on all
PMacs.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
This way firewire-ohci can be used for remote debugging like ohci1394.
Version with amendment from Fri, 11 Apr 2008 00:08:08 +0200.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Bernhard Kaindl <bk@suse.de>
|
|
Try to write dual-phase retry protocol limits to BUSY_TIMEOUT register.
- The dual-phase retry protocol is optional to implement, and if not
supported, writes to the dual-phase portion of the register will be
ignored. We try to write the original 1394-1995 default here.
- In the case of devices that are also SBP-3-compliant, all writes are
ignored, as the register is read-only, but contains single-phase retry of
15, which is what we're trying to set for all SBP-2 device anyway, so this
write attempt is safe and yields more consistent behavior for all devices.
See section 8.3.2.3.5 of the 1394-1995 spec, section 6.2 of the SBP-2 spec,
and section 6.4 of the SBP-3 spec for further details.
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
The block/unblock logic is now sufficiently tested.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
orb came from kzalloc.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
How hard can it be to switch on one bit? :-)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Write directly in big endian instead of byte-swapping after the fact.
This saves a few conversions, lets gcc use constant endianess
conversions where possible, and enables deeper endianess annotation.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Add wrappers for getting and putting a unit.
Remove some line breaks.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
|
|
The reference count of the unit dropped too low in an error path in
sbp2_probe. Fixed by moving the _get further up.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
|
|
The card->kref became obsolete since patch "firewire: fix crash in
automatic module unloading" added another counter of card users.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
|
|
The following patch limits the node speed to the host interface speed,
before using it.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
It should actually suffice to do this only for the local node's
speedcap[]. But there is another bug in the speed calculation:
The local node's speed is not correctly propagated to the speeds
which are to be used to access remote nodes.
http://thread.gmane.org/gmane.linux.kernel.firewire.devel/11772/focus=12024
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Unless you're adding a kobject to the sysfs hierarchy, there is no
point setting its kobject name.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
The failure path of ohci1394_pci_probe() reuses ohci1394_pci_remove().
Doing so it missed to call ohci1394_pmac_off() in a few unlikely early
error cases.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
to reduce the size of ohci1394.ko.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
We don't want to hide something like return in a preprocessor macro.
Unroll the macro and use a goto, which also reduces the size of
ohci1394.ko.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Clean up shared code and variable names.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
The platform feature calls in the suspend method switched off cable
power, but the calls in the resume method did not switch it back on.
Add the necessary feature call to .resume. Also add the corresponding
call to .suspend to make .suspend's behavior explicitly the same on all
PMacs.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
These drivers don't need to match any unit_directory type device.
They just need the id_table for module autoloading per module alias.
Not binding any of these drivers allows special-purpose drivers with
similar or same IDs to bind to devices. This currently only benefits
out-of-tree drivers; on the other hand it is in no way detrimental to
in-tree drivers.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
replace all:
big_endian_variable = cpu_to_beX(beX_to_cpu(big_endian_variable) +
expression_in_cpu_byteorder);
with:
beX_add_cpu(&big_endian_variable, expression_in_cpu_byteorder);
generated with semantic patch
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
* 'for-linus' of git://oss.sgi.com:8090/xfs/xfs-2.6: (87 commits)
[XFS] Fix merge failure
[XFS] The forward declarations for the xfs_ioctl() helpers and the
[XFS] Update XFS documentation for noikeep/ikeep.
[XFS] Update XFS Documentation for ikeep and ihashsize
[XFS] Remove unused HAVE_SPLICE macro.
[XFS] Remove CONFIG_XFS_SECURITY.
[XFS] xfs_bmap_compute_maxlevels should be based on di_forkoff
[XFS] Always use di_forkoff when checking for attr space.
[XFS] Ensure the inode is joined in xfs_itruncate_finish
[XFS] Remove periodic logging of in-core superblock counters.
[XFS] fix logic error in xfs_alloc_ag_vextent_near()
[XFS] Don't error out on good I/Os.
[XFS] Catch log unmount failures.
[XFS] Sanitise xfs_log_force error checking.
[XFS] Check for errors when changing buffer pointers.
[XFS] Don't allow silent errors in xfs_inactive().
[XFS] Catch errors from xfs_imap().
[XFS] xfs_bulkstat_one_dinode() never returns an error.
[XFS] xfs_iflush_fork() never returns an error.
[XFS] Catch unwritten extent conversion errors.
...
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (58 commits)
ide: remove ide_init_default_irq() macro
ide: move default IDE ports setup to ide_generic host driver
ide: remove obsoleted "idex=noprobe" kernel parameter (take 2)
ide: remove needless hwif->irq check from ide_hwif_configure()
ide: init hwif->{io_ports,irq} explicitly in legacy VLB host drivers
ide: limit legacy VLB host drivers to alpha, x86 and mips
cmd640: init hwif->{io_ports,irq} explicitly
cmd640: cleanup setup_device_ptrs()
ide: add ide-4drives host driver (take 3)
ide: remove ppc ifdef from init_ide_data()
ide: remove ide_default_io_ctl() macro
ide: remove CONFIG_IDE_ARCH_OBSOLETE_INIT
ide: add CONFIG_IDE_ARCH_OBSOLETE_DEFAULTS (take 2)
ppc/pmac: remove no longer needed IDE quirk
ppc: don't include <linux/ide.h>
ppc: remove ppc_ide_md
ppc/pplus: remove ppc_ide_md.ide_init_hwif hook
ppc/sandpoint: remove ppc_ide_md hooks
ppc/lopec: remove ppc_ide_md hooks
ppc/mpc8xx: remove ppc_ide_md hooks
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
dmaengine: ack to flags: make use of the unused bits in the 'ack' field
iop-adma: remove the workaround for missed interrupts on iop3xx
async_tx: kill ->device_dependency_added
async_tx: fix multiple dependency submission
fsldma: Split the MPC83xx event from MPC85xx and refine irq codes.
fsldma: Remove CONFIG_FSL_DMA_SELFTEST, keep fsl_dma_self_test() running always.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (79 commits)
ata-acpi: don't call _GTF for disabled drive
sata_mv add temporary 3 second init delay for SiliconImage PMs
sata_mv remove redundant edma init code
sata_mv add basic port multiplier support
sata_mv fix SOC flags, enable NCQ on SOC
sata_mv disable hotplug for now
sata_mv cosmetics
sata_mv hardreset rework
[libata] improve Kconfig help text for new PMP, SFF options
libata: make EH fail gracefully if no reset method is available
libata: Be a bit more slack about early devices
libata: cable logic
libata: move link onlineness check out of softreset methods
libata: kill dead code paths in reset path
pata_scc: fix build breakage
libata: make PMP support optional
libata: implement PMP helpers
libata: separate PMP support code from core code
libata: make SFF support optional
libata: don't use ap->ioaddr in non-SFF drivers
...
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/tglx/linux-2.6-hrt:
clocksource: make clocksource watchdog cycle through online CPUs
Documentation: move timer related documentation to a single place
clockevents: optimise tick_nohz_stop_sched_tick() a bit
locking: remove unused double_spin_lock()
hrtimers: simplify lockdep handling
timers: simplify lockdep handling
posix-timers: fix shadowed variables
timer_list: add annotations to workqueue.c
hrtimer: use nanosleep specific restart_block fields
hrtimer: add nanosleep specific restart_block member
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shaggy/jfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/shaggy/jfs-2.6:
jfs: replace __inline with inline
jfs: le*_add_cpu conversion
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-kgdb:
kgdb: always use icache flush for sw breakpoints
kgdb: fix SMP NMI kgdb_handle_exception exit race
kgdb: documentation fixes
kgdb: allow static kgdbts boot configuration
kgdb: add documentation
kgdb: Kconfig fix
kgdb: add kgdb internal test suite
kgdb: fix several kgdb regressions
kgdb: kgdboc pl011 I/O module
kgdb: fix optional arch functions and probe_kernel_*
kgdb: add x86 HW breakpoints
kgdb: print breakpoint removed on exception
kgdb: clocksource watchdog
kgdb: fix NMI hangs
kgdb: fix kgdboc dynamic module configuration
kgdb: document parameters
x86: kgdb support
consoles: polling support, kgdboc
kgdb: core
uaccess: add probe_kernel_write()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86: (613 commits)
x86: standalone trampoline code
x86: move suspend wakeup code to C
x86: coding style fixes to arch/x86/kernel/acpi/sleep.c
x86: setup_trampoline() - fix section mismatch warning
x86: section mismatch fixes, #1
x86: fix paranoia about using BIOS quickboot mechanism.
x86: print out buggy mptable
x86: use cpu_online()
x86: use cpumask_of_cpu()
x86: remove unnecessary tmp local variable
x86: remove unnecessary memset()
x86: use ioapic_read_entry() and ioapic_write_entry()
x86: avoid redundant loop in io_apic_level_ack_pending()
x86: remove superfluous initialisation in boot code.
x86: merge mpparse_{32,64}.c
x86: unify mp_register_gsi
x86: unify mp_config_acpi_legacy_irqs
x86: unify mp_register_ioapic
x86: unify uniq_io_apic_id
x86: unify smp_scan_config
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/willy/misc
* 'semaphore' of git://git.kernel.org/pub/scm/linux/kernel/git/willy/misc:
Remove DEBUG_SEMAPHORE from Kconfig
Improve semaphore documentation
Simplify semaphore implementation
Add down_timeout and change ACPI to use it
Introduce down_killable()
Generic semaphore implementation
Add semaphore.h to kernel_lock.c
Fix quota.h includes
|
