aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2009-03-17USB: image/mdc800, fix lock imbalanceJiri Slaby
There is an omitted unlock in mdc800_usb_probe's fail path. Add it. Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Cc: Henning Zabel <henning@uni-paderborn.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-03-17USB: atm/cxacru, fix lock imbalanceJiri Slaby
We do not hold mutex in one place in cxacru_cm, but unlock it on fail path. Fix this. Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Cc: Simon Arlott <cxacru@fire.lp0.eu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-03-17USB: unusual_devs: Add support for GI 0431 SD-Card interfaceJan Dumon
Enable the SD-Card interface on the GI 0431 HSUPA stick from Option. The unusual_devs.h entry is necessary because the device descriptor is vendor-specific. That prevents usb-storage from binding to it as an interface driver. T: Bus=07 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 15 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=ff Prot=ff MxPS=64 #Cfgs= 1 P: Vendor=0af0 ProdID=7501 Rev= 0.00 S: Manufacturer=Option N.V. S: Product=Globetrotter HSUPA Modem C:* #Ifs=11 Cfg#= 1 Atr=a0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=hso E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=hso E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=hso E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 7 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=hso E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=08(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 8 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=09(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 9 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=hso E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=8b(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=0a(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#=10 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage E: Ad=0b(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=8c(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms Signed-off-by: Jan Dumon <j.dumon@option.com> Signed-off-by: Phil Dibowitz <phil@ipom.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-03-17USB: serial: new cp2101 device idRobert M. Kenney
From: Robert M. Kenney <rmk@unh.edu> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-03-17USB: serial: ftdi: enable UART detection on gnICE JTAG adaptors blacklist ↵Michael Hennerich
interface0 Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-03-17USB: serial: add FTDI USB/Serial converter devicesAxel Wachtler
Add the following devices to the USB FTDI SIO device table: Bus 001 Device 009: ID 03eb:2109 Atmel Corp. http://www.atmel.com/dyn/products/tools_card.asp?tool_id=4187 Bus 001 Device 008: ID 1cf1:0001 http://www.dresden-elektronik.de/shop/prod75.html Bus 001 Device 007: ID 1c1f:0004 http://www.dresden-elektronik.de/shop/prod64.html Signed-off-by: Axel Wachtler <axel.wachtler@atmel.com> Signed-off-by: Robert Richter <robert.richter@amd.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-03-17USB: usbfs: keep async URBs until the device file is closedAlan Stern
The usbfs driver manages a list of completed asynchronous URBs. But it is too eager to free the entries on this list: destroy_async() gets called whenever an interface is unbound or a device is removed, and it deallocates the outstanding struct async entries for all URBs on that interface or device. This is wrong; the user program should be able to reap an URB any time after it has completed, regardless of whether or not the interface is still bound or the device is still present. This patch (as1222) moves the code for deallocating the completed list entries from destroy_async() to usbdev_release(). The outstanding entries won't be freed until the user program has closed the device file, thereby eliminating any possibility that the remaining URBs might still be reaped. This fixes a bug in which a program can hang in the USBDEVFS_REAPURB ioctl when the device is unplugged. Reported-and-tested-by: Martin Poupe <martin.poupe@upek.com> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-03-17USB: usbtmc: add protocol 1 supportGreg Kroah-Hartman
The driver already supports the 1 protocol support, so just add it to the MODULE_DEVICE_TABLE entry so it properly picks up these devices. Thanks to Jouni Rynö for pointing this out. Reported-by: Jouni Ryno <Jouni.Ryno@fmi.fi> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-03-17USB: usbtmc: fix stupid bug in open()Greg Kroah-Hartman
open() will never succeed, as we always return -ENODEV. Fix this obvious bug. Thanks to Jouni Ryno for reporting it. Reported-by: Jouni Ryno <Jouni.Ryno@fmi.fi> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-03-17Avoid 64-bit "switch()" statements on 32-bit architecturesLinus Torvalds
Commit ee6f779b9e0851e2f7da292a9f58e0095edf615a ("filp->f_pos not correctly updated in proc_task_readdir") changed the proc code to use filp->f_pos directly, rather than through a temporary variable. In the process, that caused the operations to be done on the full 64 bits, even though the offset is never that big. That's all fine and dandy per se, but for some unfathomable reason gcc generates absolutely horrid code when using 64-bit values in switch() statements. To the point of actually calling out to gcc helper functions like __cmpdi2 rather than just doing the trivial comparisons directly the way gcc does for normal compares. At which point we get link failures, because we really don't want to support that kind of crazy code. Fix this by just casting the f_pos value to "unsigned long", which is plenty big enough for /proc, and avoids the gcc code generation issue. Reported-by: Alexey Dobriyan <adobriyan@gmail.com> Cc: Zhang Le <r0bertz@gentoo.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-03-17prevent boosting kprobes on exception addressMasami Hiramatsu
Don't boost at the addresses which are listed on exception tables, because major page fault will occur on those addresses. In that case, kprobes can not ensure that when instruction buffer can be freed since some processes will sleep on the buffer. kprobes-ia64 already has same check. Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com> Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-03-17Merge git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dmLinus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm: dm crypt: wait for endio to complete before destruction dm crypt: fix kcryptd_async_done parameter dm io: respect BIO_MAX_PAGES limit dm table: rework reference counting fix dm ioctl: validate name length when renaming
2009-03-17Fast TSC calibration: calculate proper frequency error boundsLinus Torvalds
In order for ntpd to correctly synchronize the clocks, the frequency of the system clock must not be off by more than 500 ppm (or, put another way, 1:2000), or ntpd will end up giving up on trying to synchronize properly, and ends up reseting the clock in jumps instead. The fast TSC PIT calibration sometimes failed this test - it was assuming that the PIT reads always took about one microsecond each (2us for the two reads to get a 16-bit timer), and that calibrating TSC to the PIT over 15ms should thus be sufficient to get much closer than 500ppm (max 2us error on both sides giving 4us over 15ms: a 270 ppm error value). However, that assumption does not always hold: apparently some hardware is either very much slower at reading the PIT registers, or there was other noise causing at least one machine to get 700+ ppm errors. So instead of using a fixed 15ms timing loop, this changes the fast PIT calibration to read the TSC delta over the individual PIT timer reads, and use the result to calculate the error bars on the PIT read timing properly. We then successfully calibrate the TSC only if the maximum error bars fall below 500ppm. In the process, we also relax the timing to allow up to 25ms for the calibration, although it can happen much faster depending on hardware. Reported-and-tested-by: Jesper Krogh <jesper@krogh.cc> Cc: john stultz <johnstul@us.ibm.com> Cc: Thomas Gleixner <tglx@linutronix.de> Acked-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-03-17Fix potential fast PIT TSC calibration startup glitchLinus Torvalds
During bootup, when we reprogram the PIT (programmable interval timer) to start counting down from 0xffff in order to use it for the fast TSC calibration, we should also make sure to delay a bit afterwards to allow the PIT hardware to actually start counting with the new value. That will happens at the next CLK pulse (1.193182 MHz), so the easiest way to do that is to just wait at least one microsecond after programming the new PIT counter value. We do that by just reading the counter value back once - which will take about 2us on PC hardware. Reported-and-tested-by: john stultz <johnstul@us.ibm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-03-16Merge branch 'release' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6 * 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: acpi-wmi: unsigned cannot be less than 0 thinkpad-acpi: fix module autoloading for older models acer-wmi: Unmark as 'experimental' acpi-wmi: Unmark as 'experimental' acer-wmi: double free in acer_rfkill_exit() platform/x86: depends instead of select for laptop platform drivers asus-laptop: use select instead of depends on eeepc-laptop: restore acpi_generate_proc_event() asus-laptop: restore acpi_generate_proc_event() acpi: check for pxm_to_node_map overflow ACPI: remove doubled status checking ACPI suspend: Blacklist Toshiba Satellite L300 that requires to set SCI_EN directly on resume Revert "ACPI: make some IO ports off-limits to AML" suspend: switch the Asus Pundit P1-AH2 to old ACPI sleep ordering
2009-03-16dm crypt: wait for endio to complete before destructionMilan Broz
The following oops has been reported when dm-crypt runs over a loop device. ... [ 70.381058] Process loop0 (pid: 4268, ti=cf3b2000 task=cf1cc1f0 task.ti=cf3b2000) ... [ 70.381058] Call Trace: [ 70.381058] [<d0d76601>] ? crypt_dec_pending+0x5e/0x62 [dm_crypt] [ 70.381058] [<d0d767b8>] ? crypt_endio+0xa2/0xaa [dm_crypt] [ 70.381058] [<d0d76716>] ? crypt_endio+0x0/0xaa [dm_crypt] [ 70.381058] [<c01a2f24>] ? bio_endio+0x2b/0x2e [ 70.381058] [<d0806530>] ? dec_pending+0x224/0x23b [dm_mod] [ 70.381058] [<d08066e4>] ? clone_endio+0x79/0xa4 [dm_mod] [ 70.381058] [<d080666b>] ? clone_endio+0x0/0xa4 [dm_mod] [ 70.381058] [<c01a2f24>] ? bio_endio+0x2b/0x2e [ 70.381058] [<c02bad86>] ? loop_thread+0x380/0x3b7 [ 70.381058] [<c02ba8a1>] ? do_lo_send_aops+0x0/0x165 [ 70.381058] [<c013754f>] ? autoremove_wake_function+0x0/0x33 [ 70.381058] [<c02baa06>] ? loop_thread+0x0/0x3b7 When a table is being replaced, it waits for I/O to complete before destroying the mempool, but the endio function doesn't call mempool_free() until after completing the bio. Fix it by swapping the order of those two operations. The same problem occurs in dm.c with md referenced after dec_pending. Again, we swap the order. Cc: stable@kernel.org Signed-off-by: Milan Broz <mbroz@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-03-16dm crypt: fix kcryptd_async_done parameterHuang Ying
In the async encryption-complete function (kcryptd_async_done), the crypto_async_request passed in may be different from the one passed to crypto_ablkcipher_encrypt/decrypt. Only crypto_async_request->data is guaranteed to be same as the one passed in. The current kcryptd_async_done uses the passed-in crypto_async_request directly which may cause the AES-NI-based AES algorithm implementation to panic. This patch fixes this bug by only using crypto_async_request->data, which points to dm_crypt_request, the crypto_async_request passed in. The original data (convert_context) is gotten from dm_crypt_request. [mbroz@redhat.com: reworked] Cc: stable@kernel.org Signed-off-by: Huang Ying <ying.huang@intel.com> Cc: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Milan Broz <mbroz@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-03-16dm io: respect BIO_MAX_PAGES limitMikulas Patocka
dm-io calls bio_get_nr_vecs to get the maximum number of pages to use for a given device. It allocates one additional bio_vec to use internally but failed to respect BIO_MAX_PAGES, so fix this. This was the likely cause of: https://bugzilla.redhat.com/show_bug.cgi?id=173153 Cc: stable@kernel.org Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-03-16dm table: rework reference counting fixMikulas Patocka
Fix an error introduced in dm-table-rework-reference-counting.patch. When there is failure after table initialization, we need to use dm_table_destroy, not dm_table_put, to free the table. dm_table_put may be used only after dm_table_get. Cc: Kiyoshi Ueda <k-ueda@ct.jp.nec.com> Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Reviewed-by: Jonathan Brassow <jbrassow@redhat.com> Reviewed-by: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-03-16dm ioctl: validate name length when renamingMilan Broz
When renaming a mapped device validate the length of the new name. The rename ioctl accepted any correctly-terminated string enclosed within the data passed from userspace. The other ioctls enforce a size limit of DM_NAME_LEN. If the name is changed and becomes longer than that, the device can no longer be addressed by name. Fix it by properly checking for device name length (including terminating zero). Cc: stable@kernel.org Signed-off-by: Milan Broz <mbroz@redhat.com> Reviewed-by: Jonathan Brassow <jbrassow@redhat.com> Reviewed-by: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-03-16Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits) r8169: revert "r8169: read MAC address from EEPROM on init (2nd attempt)" r8169: use hardware auto-padding. igb: remove ASPM L0s workaround netxen: remove old flash check. mv643xx_eth: fix unicast address filter corruption on mtu change xfrm: Fix xfrm_state_find() wrt. wildcard source address. emac: Fix clock control for 405EX and 405EXr chips ixgbe: fix multiple unicast address support via-velocity: Fix DMA mapping length errors on transmit. qlge: bugfix: Pad outbound frames smaller than 60 bytes. qlge: bugfix: Move netif_napi_del() to common call point. qlge: bugfix: Tell hw to strip vlan header. qlge: bugfix: Increase filter on inbound csum. dnet: replace obsolete *netif_rx_* functions with *napi_* net: Add be2net driver. dnet: Fix warnings on 64-bit. dnet: Dave DNET ethernet controller driver (updated) ipv6: Fix BUG when disabled ipv6 module is unloaded bnx2x: Using DMAE to initialize the chip bnx2x: Casting page alignment ...
2009-03-16linux.conf.au 2009: TuzRusty Russell
Impact: help prevent extinction of species The Tasmanian Devil is a shy iconic Australian creature named for its spine-chilling screech. It is threatened with extinction due to a scientifically interesting but horrific transmissible facial cancer. This one is standing in for Tux for one release using the far less-known Devil Facial Tux Disguise. Save The Tasmanian Devil http://tassiedevil.com.au Signed-off-by: Linux.conf.au Hobart Team <contact@marchsouth.org> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-03-16filp->f_pos not correctly updated in proc_task_readdirZhang Le
filp->f_pos only get updated at the end of the function. Thus d_off of those dirents who are in the middle will be 0, and this will cause a problem in glibc's readdir implementation, specifically endless loop. Because when overflow occurs, f_pos will be set to next dirent to read, however it will be 0, unless the next one is the last one. So it will start over again and again. There is a sample program in man 2 gendents. This is the output of the program running on a multithread program's task dir before this patch is applied: $ ./a.out /proc/3807/task --------------- nread=128 --------------- i-node# file type d_reclen d_off d_name 506442 directory 16 1 . 506441 directory 16 0 .. 506443 directory 16 0 3807 506444 directory 16 0 3809 506445 directory 16 0 3812 506446 directory 16 0 3861 506447 directory 16 0 3862 506448 directory 16 8 3863 This is the output after this patch is applied $ ./a.out /proc/3807/task --------------- nread=128 --------------- i-node# file type d_reclen d_off d_name 506442 directory 16 1 . 506441 directory 16 2 .. 506443 directory 16 3 3807 506444 directory 16 4 3809 506445 directory 16 5 3812 506446 directory 16 6 3861 506447 directory 16 7 3862 506448 directory 16 8 3863 Signed-off-by: Zhang Le <r0bertz@gentoo.org> Acked-by: Al Viro <viro@ZenIV.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-03-16Merge branches 'misc-up-now' and 'platform-drivers' into releaseLen Brown
2009-03-16acpi-wmi: unsigned cannot be less than 0Roel Kluin
include/linux/pci-acpi.h:74: typedef u32 acpi_status; result is unsigned, so an error returned by acpi_bus_register_driver() will not be noticed. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com>
2009-03-16thinkpad-acpi: fix module autoloading for older modelsMathieu Chouquet-Stringer
Looking at the source, there seems to be a missing * to match my DMI string. I mean for newer IBM and Lenovo's laptops you match either one of the following: MODULE_ALIAS("dmi:bvnIBM:*:svnIBM:*:pvrThinkPad*:rvnIBM:*"); MODULE_ALIAS("dmi:bvnLENOVO:*:svnLENOVO:*:pvrThinkPad*:rvnLENOVO:*"); While for older Thinkpads, you do this (for instance): IBM_BIOS_MODULE_ALIAS("1[0,3,6,8,A-G,I,K,M-P,S,T]"); with IBM_BIOS_MODULE_ALIAS being MODULE_ALIAS("dmi:bvnIBM:bvr" __type "ET??WW") Note there's no * terminating the string. As result, udev doesn't load anything because modprobe cannot find anything matching this (my machine actually): udevtest: run: '/sbin/modprobe dmi:bvnIBM:bvr1IET71WW(2.10):bd06/16/2006:svnIBM:pn236621U:pvrNotAv Signed-off-by: Mathieu Chouquet-Stringer <mchouque@free.fr> Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Signed-off-by: Len Brown <len.brown@intel.com>
2009-03-16acer-wmi: Unmark as 'experimental'Carlos Corbacho
This driver has been around and used long enough that we can drop the 'experimental'. Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk> Signed-off-by: Len Brown <len.brown@intel.com>
2009-03-16acpi-wmi: Unmark as 'experimental'Carlos Corbacho
ACPI-WMI isn't experimental anymore, and there are other drivers that now depend on it that aren't either. Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk> Signed-off-by: Len Brown <len.brown@intel.com>
2009-03-16acer-wmi: double free in acer_rfkill_exit()Dan Carpenter
This is acer_rfkill_exit() from drivers/platform/x86/acer-wmi.c. The code frees wireless_rfkill->data again instead of bluetooth_rfkill->data. This was found using a code checker (http://repo.or.cz/w/smatch.git/). Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk> Signed-off-by: Len Brown <len.brown@intel.com>
2009-03-16platform/x86: depends instead of select for laptop platform driversCorentin Chary
"I hate `select' and will gleefully leap on any s/select/depends/ patch, whether it works or not :)" Andrew Morton select INPUT is not needed here, because if someone doesn't want INPUT, he won't want these drivers either. Signed-off-by: Corentin Chary <corentincj@iksaif.net> Signed-off-by: Len Brown <len.brown@intel.com>
2009-03-16asus-laptop: use select instead of depends onCorentin Chary
Like thinkpad_acpi or eeepc-laptop, asus-laptop will now use "select" instead of "depends on" for LEDS_CLASS, NEW_LEDS and BACKLIGHT_CLASS_DEVICE Signed-off-by: Corentin Chary <corentincj@iksaif.net> Signed-off-by: Len Brown <len.brown@intel.com>
2009-03-16eeepc-laptop: restore acpi_generate_proc_event()Corentin Chary
Restore acpi_generate_proc_event() for backward compatibility with old acpi scripts. Signed-off-by: Corentin Chary <corentincj@iksaif.net> Signed-off-by: Len Brown <len.brown@intel.com>
2009-03-16asus-laptop: restore acpi_generate_proc_event()Corentin Chary
Restore acpi_generate_proc_event() for backward compatibility with old acpi scripts. Signed-off-by: Corentin Chary <corentincj@iksaif.net> Signed-off-by: Len Brown <len.brown@intel.com>
2009-03-16acpi: check for pxm_to_node_map overflowCyrill Gorcunov
It is hardly (if ever) possible but in case of broken _PXM entry we could reach out of pxm_to_node_map array bounds in acpi_map_pxm_to_node() call. Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com>
2009-03-16ACPI: remove doubled status checkingJiri Slaby
There was a misplaced status test (two consequent tests without a statement in between) in acpi_bus_init for ages. Remove it, since the function which should be checked (acpi_os_initialize1) has BUG_ONs on failure paths. Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com>
2009-03-16ACPI suspend: Blacklist Toshiba Satellite L300 that requires to set SCI_EN ↵Zhang Rui
directly on resume This is a supplement of commit 65df78473ffbf3bff5e2034df1638acc4f3ddd50. http://bugzilla.kernel.org/show_bug.cgi?id=12798 Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
2009-03-16Revert "ACPI: make some IO ports off-limits to AML"Len Brown
This reverts commit 5ec5d38a1c8af255ffc481c81eef13e9155524b3. because it caused spurious dmesg warmings. We'll implement the check for off-limit ports in a more clever way in the future. http://bugzilla.kernel.org/show_bug.cgi?id=12758 Signed-off-by: Len Brown <len.brown@intel.com>
2009-03-16suspend: switch the Asus Pundit P1-AH2 to old ACPI sleep orderingAndy Whitcroft
Switch the Asus Pundit P1-AH2 (M2N8L motherboard) to the old ACPI 1.0 sleep ordering by default. Without this it will not suspend/resume correctly. Signed-off-by: Andy Whitcroft <apw@canonical.com> Tested-by: Dustin Kirkland <kirkland@canonical.com> Signed-off-by: Len Brown <len.brown@intel.com>
2009-03-15r8169: revert "r8169: read MAC address from EEPROM on init (2nd attempt)"françois romieu
It fails on the following systems: - RTL8169sc/8110sc (XID 18000000) reported by Tim Durack <tdurack@gmail.com> (x86) - RTL8169sb/8110sb (XID 10000000) reported by Mikael Pettersson <mikpe@it.uu.se> (ARM) The patch appeared to work on x86 for the following systems: RTL8169sb/8110sb 10000000 PCI (EXT) RTL8110s 04000000 PCI (EXT) RTL8102e 24a00000 PCI-E (LOM) RTL8168c/8111c 3c2000c0 PCI-E (LOM) RTL8168b/8111b 38000000 PCI-E (LOM) RTL8168b/8111b 38000000 PCI-E (EXT) The patch exposes two problems: 1) while not completely wrong, mac addresses are not read correctly from the EEPROM 2) the MAC address registers are not correctly set Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Tested-by: Mikael Pettersson <mikpe@it.uu.se> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-15r8169: use hardware auto-padding.françois romieu
It shortens the code and fixes the current pci_unmap leak with padded skb reported by Dave Jones. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-15parisc: sba_iommu: fix build bug when CONFIG_PARISC_AGP=yKyle McMartin
CC drivers/parisc/sba_iommu.o drivers/parisc/sba_iommu.c:1373: error: expected identifier or '(' before '}' token make[2]: *** [drivers/parisc/sba_iommu.o] Error 1 make[1]: *** [drivers/parisc] Error 2 make: *** [drivers] Error 2 Don't know how this has gone missed for so long... clearly I need to do builds on my C8000 more often. Signed-off-by: Kyle McMartin <kyle@mcmartin.ca> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-03-15Merge master.kernel.org:/home/rmk/linux-2.6-armLinus Torvalds
* master.kernel.org:/home/rmk/linux-2.6-arm: (23 commits) [ARM] Fix virtual to physical translation macro corner cases [ARM] update mach-types [ARM] 5421/1: ftrace: fix crash due to tracing of __naked functions MX1 fix include [ARM] 5419/1: ep93xx: fix build warnings about struct i2c_board_info [ARM] 5418/1: restore lr before leaving mcount ARM: OMAP: board-omap3beagle: set i2c-3 to 100kHz ARM: OMAP: Allow I2C bus driver to be compiled as a module ARM: OMAP: sched_clock() corrected ARM: OMAP: Fix compile error if pm.h is included [ARM] orion5x: pass dram mbus data to xor driver [ARM] S3C64XX: Fix s3c64xx_setrate_clksrc [ARM] S3C64XX: sparse warnings in arch/arm/plat-s3c64xx/irq.c [ARM] S3C64XX: sparse warnings in arch/arm/plat-s3c64xx/s3c6400-clock.c [ARM] S3C64XX: Fix USB host clock mux list [ARM] S3C64XX: Fix name of USB host clock. [ARM] S3C64XX: Rename IRQ_UHOST to IRQ_USBH [ARM] S3C64XX: Do gpiolib configuration earlier [ARM] S3C64XX: Staticise s3c64xx_init_irq_eint() [ARM] SMDK6410: Declare iodesc table static ...
2009-03-14igb: remove ASPM L0s workaroundAlexander Duyck
The L0s workaround should be moved into a pci quirk and so it is not necessary in the driver. This update removes the L0s workaround from the igb driver. This was the second half of the PCI quirk patch that Matthew Wilcox did not pick up when he picked up the quirk patch. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-14Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-blockLinus Torvalds
* 'for-linus' of git://git.kernel.dk/linux-2.6-block: Fix Xilinx SystemACE driver to handle empty CF slot block: fix memory leak in bio_clone() block: Add gfp_mask parameter to bio_integrity_clone()
2009-03-14Fix Xilinx SystemACE driver to handle empty CF slotGrant Likely
The SystemACE driver does not handle an empty CF slot gracefully. An empty CF slot ends up hanging the system. This patch adds a check for the CF state and stops trying to process requests if the slot is empty. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-03-14block: fix memory leak in bio_clone()Li Zefan
If bio_integrity_clone() fails, bio_clone() returns NULL without freeing the newly allocated bio. Signed-off-by: Li Zefan <lizf@cn.fujitsu.com> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-03-14block: Add gfp_mask parameter to bio_integrity_clone()un'ichi Nomura
Stricter gfp_mask might be required for clone allocation. For example, request-based dm may clone bio in interrupt context so it has to use GFP_ATOMIC. Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com> Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Cc: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-03-14Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linusLinus Torvalds
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: MIPS: Mark Eins: Fix configuration. MIPS: Fix TIF_32BIT undefined problem when seccomp is disabled
2009-03-14Merge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: (31 commits) [SCSI] qla2xxx: Update version number to 8.03.00-k4. [SCSI] qla2xxx: Correct overwrite of pre-assigned init-control-block structure size. [SCSI] qla2xxx: Correct truncation in return-code status checking. [SCSI] qla2xxx: Correct vport delete bug. [SCSI] qla2xxx: Use correct value for max vport in LOOP topology. [SCSI] qla2xxx: Correct address range checking for option-rom updates. [SCSI] fcoe: Change fcoe receive thread nice value from 19 (lowest priority) to -20 [SCSI] fcoe: fix handling of pending queue, prevent out of order frames (v3) [SCSI] fcoe: Out of order tx frames was causing several check condition SCSI status [SCSI] fcoe: fix kfree(skb) [SCSI] fcoe: ETH_P_8021Q is already in if_ether and fcoe is not using it anyway [SCSI] libfc: do not change the fh_rx_id of a recevied frame [SCSI] fcoe: Correct fcoe_transports initialization vs. registration [SCSI] fcoe: Use setup_timer() and mod_timer() [SCSI] libfc, fcoe: Remove unnecessary cast by removing inline wrapper [SCSI] libfc, fcoe: Cleanup function formatting and minor typos [SCSI] libfc, fcoe: Fix kerneldoc comments [SCSI] libfc: Cleanup libfc_function_template comments [SCSI] libfc: check for err when recv and state is incorrect [SCSI] libfc: rename rp to rdata in fc_disc_new_target() ...
2009-03-14Merge branch 'upstream-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev * 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: ata_piix: add workaround for Samsung DB-P70 libata: Keep shadow last_ctl up to date during resets sata_mv: fix MSI irq race condition
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-03 10:34:14 +0000