aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2007-03-28SUN3/3X Lance trivial fix improvedCyrill V. Gorcunov
This patch adds checking for allocated DVMA memory and granted IRQ line. Signed-off-by: Cyrill V. Gorcunov <gorcunov@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-03-28mv643xx_eth: Fix use of uninitialized port_num fieldGabriel Paubert
In this driver, the default ethernet address is first set by by calling eth_port_uc_addr_get() which reads the relevant registers of the corresponding port as initially set by firmware. However that function used the port_num field accessed through the private area of net_dev before it was set. The result was that one board I have ended up with the unicast address set to 00:00:00:00:00:00 (only port 1 is connected on this board). The problem appeared after commit 84dd619e4dc3b0b1c40dafd98c90fd950bce7bc5. This patch fixes the bug by setting mp->port_num prior to calling eth_port_uc_get_addr(). Signed-off-by: Gabriel Paubert <paubert@iram.es> Signed-off-by: Dale Farnsworth <dale@farnsworth.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-03-28forcedeth: fix tx timeoutAyaz Abdulla
The tx timeout routine was waking the tx queue conditionally. However, it must call it unconditionally since the dev_watchdog has halted the tx queue before calling the timeout function. Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-03-28forcedeth: fix nic pollAyaz Abdulla
The nic poll routine was missing the call to the optimized irq routine. This patch adds the missing call for the optimized path. See http://bugzilla.kernel.org/show_bug.cgi?id=7950 for more information. Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-03-28qla3xxx: bugfix: Jumbo frame handling.Ron Mercer
Fixed rx checksum bits. Turn on TCP processing for rx checksum. Fixed max frame length register write. It wasn't getting set in multi-port system. Set rx buffer queue length properly for jumbo frames. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-03-28qla3xxx: bugfix: Dropping interrupt under heavy network load.Ron Mercer
Update the rx queue pointer when exiting NAPI poll rather than at the end of each iteration. Remove unnecessary PCI flushes that occurred after every write. Now write all regs and flush once. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-03-28qla3xxx: bugfix: Multi segment sends were getting whacked.Ron Mercer
The proper header length was not being used. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-03-28qla3xxx: bugfix: Add tx control block memset.Ron Mercer
This was removed in a previous patch to increase performance, but caused a transmit error for the 4032 chip. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-03-28atl1: remove unnecessary crc inversionJay Cliburn
The original vendor driver contained a private ether_crc_le() function that produced an inverted crc. When we changed to the kernel version of ether_crc_le(), we neglected to undo the inversion. Let's do it now. Discovered by and patch proffered by Jose Alberto Reguero. Signed-off-by: Jose Alberto Reguero <jareguero@telefonica.net> Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-03-28myri10ge: correctly detect when TSO should be usedBrice Goglin
Correctly detect when TSO should be used on transmit by looking at the skb->gso_size rather than seeing if the frame was larger than our MTU. The old method causes problems when a host with a large (jumbo) MTU is sending to a host with a small (standard) MTU. Signed-off-by: Brice Goglin <brice@myri.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-03-27[PATCH] aio: remove bare user-triggerable error printkZach Brown
The user can generate console output if they cause do_mmap() to fail during sys_io_setup(). This was seen in a regression test that does exactly that by spinning calling mmap() until it gets -ENOMEM before calling io_setup(). We don't need this printk at all, just remove it. Signed-off-by: Zach Brown <zach.brown@oracle.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-03-27Merge master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6Linus Torvalds
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: [SCSI] gdth: fix oops in gdth_copy_cmd() [SCSI] mptsas: Fix oops for insmod during kexec [SCSI] lpfc: avoid double-free during PCI error failure
2007-03-27Merge git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvbLinus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: V4L/DVB (5472): Isl6421: don't reference freed memory V4L/DVB (5441): Saa7146: Fix allocation of clipping memory V4L/DVB (5421): Fix suspend/resume in msp3400 and tuner V4L/DVB (5415): Msp_attach must return 0 if no msp3400 was found. V4L/DVB (5408): Fix SECAM handling on saa7115 V4L/DVB (5400): Core: fix several locking related problems V4L/DVB (5390): Radio: Fix error in Kbuild file V4L/DVB (5332): Ir_rc5_timer_end decoder lockup fix
2007-03-27Merge git://kvm.qumranet.com/home/avi/kvmLinus Torvalds
* git://kvm.qumranet.com/home/avi/kvm: KVM: always reload segment selectors KVM: Prevent system selectors leaking into guest on real->protected mode transition on vmx
2007-03-27[PATCH] Revert "swsusp: disable nonboot CPUs before entering platform suspend"Rafael J. Wysocki
This reverts commit 94985134b7b46848267ed6b734320db01c974e72 and insteads removes the WARN_ON() that caused that commit in the first place. The problem is that we call disable_nonboot_cpus() in swsusp before powering down the system in order to avoid triggering the WARN_ON() in arch/x86_64/kernel/acpi/sleep.c:init_low_mapping() and this doesn't work well on Thomas' system. So instead, remove the WARN_ON() in arch/x86_64/kernel/acpi/sleep.c: init_low_mapping(), which triggers every time during the suspend to disk in the platform mode, as the potential problem it is related to doesn't seem to occur in practice. [ I think we might want to disallow the case of multiple users of that mm, or something. Normally, playing with the current process page tables on the current CPU should be fine as long as we don't have other threads using those tables at the same time.. Anyway, not pretty, but better than the warning or the lockup - Linus ] Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-03-27[PATCH] i386: Fix bogus return value in hpet_next_event()Thomas Gleixner
The clockevents / tick management code expects an error value, when the event is already expired. hpet_next_event() returns 1 in that case. Fix it to return the proper -ETIME error code. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-03-27Merge branch 'for-linus' of git://git.kernel.dk/data/git/linux-2.6-blockLinus Torvalds
* 'for-linus' of git://git.kernel.dk/data/git/linux-2.6-block: Export __splice_from_pipe() 2/2 splice: dont readpage 1/2 splice: dont steal make elv_register() output atomic block: blk_max_pfn is somtimes wrong
2007-03-27[PATCH] Fix kernel build with EMBEDDED & PROC_FS & !PROC_SYSCTLMika Kukkonen
Without attached patch against current -git I get following with !PROC_SYSCTL (with EMBEDDED and PROC_FS set): CC init/version.o LD init/built-in.o LD vmlinux fs/built-in.o: In function `do_proc_sys_lookup': proc_sysctl.c:(.text+0x26583): undefined reference to `sysctl_head_next' fs/built-in.o: In function `proc_sys_revalidate': proc_sysctl.c:(.text+0x265bb): undefined reference to `sysctl_head_finish' fs/built-in.o: In function `proc_sys_readdir': proc_sysctl.c:(.text+0x26720): undefined reference to `sysctl_head_next' proc_sysctl.c:(.text+0x267d8): undefined reference to `sysctl_head_finish' proc_sysctl.c:(.text+0x268e7): undefined reference to `sysctl_head_next' proc_sysctl.c:(.text+0x26910): undefined reference to `sysctl_head_finish' fs/built-in.o: In function `proc_sys_write': proc_sysctl.c:(.text+0x2695d): undefined reference to `sysctl_perm' proc_sysctl.c:(.text+0x2699c): undefined reference to `sysctl_head_finish' fs/built-in.o: In function `proc_sys_read': proc_sysctl.c:(.text+0x269e9): undefined reference to `sysctl_perm' proc_sysctl.c:(.text+0x26a25): undefined reference to `sysctl_head_finish' fs/built-in.o: In function `proc_sys_permission': proc_sysctl.c:(.text+0x26ad1): undefined reference to `sysctl_perm' proc_sysctl.c:(.text+0x26adb): undefined reference to `sysctl_head_finish' fs/built-in.o: In function `proc_sys_lookup': proc_sysctl.c:(.text+0x26b39): undefined reference to `sysctl_head_finish' make: *** [vmlinux] Virhe 1 All those functions are in fs/proc/proc_sysctl.c, which has no CONFIG_ #define's in it, so the patch makes the compilation of that file to depend on CONFIG_PROC_SYSCTL (the simplest choice). Acked-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-03-27[PATCH] I2O: remove Markus from MAINTAINERSMarkus Lidel
Because i don't have much time lately and my responses are pretty slow it's probably best to remove me from MAINTAINERS to give someone else the chance to jump in. Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-03-27[PATCH] ipcns: fix !CONFIG_IPC_NS behaviorSerge E. Hallyn
When CONFIG_IPC_NS=n, clone(CLONE_NEWIPC) claims success, but did not actually clone a new IPC namespace. Fix this to return -EINVAL so the caller knows his request was denied. Signed-off-by: Serge E. Hallyn <serue@us.ibm.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-03-27[PATCH] i2o: block IO errors on i2o diskVasily Averin
I2O subsystem has been broken in mainstream several months ago (after 2.6.18). Commit 4aff5e2333c9a1609662f2091f55c3f6fffdad36 from Jens Axboe split struct request ->flags into two parts: cmd_type and cmd_flags. In i2o layer this patch has replaced flag REQ_SPECIAL by the according cmd_type. However i2o has used REQ_SPECIAL not as command type but as driver-specific flag for the debug purposes. As result all i2o requests have type "special" now, are not processed to the hardware and fail with I/O error: i2o/hda:<3>Buffer I/O error on device i2o/hda, logical block 0 Buffer I/O error on device i2o/hda, logical block 0 Buffer I/O error on device i2o/hda, logical block 0 unable to read partition table block-osm: device added (TID: 207): i2o/hda The following patch removes the extra debug checks without any drawbacks and restores the normal driver's work. Signed-off-by: Vasily Averin <vvs@sw.ru> Acked-by: Markus Lidel <Markus.Lidel@shadowconnect.com> Cc: Jens Axboe <jens.axboe@oracle.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-03-27[PATCH] Fix struct device member name in PCMCIA au1000_genericYoichi Yuasa
drivers/pcmcia/au1000_generic.c: In function 'au1x00_pcmcia_socket_probe': drivers/pcmcia/au1000_generic.c:375: error: 'struct device' has no member named 'dev' Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Jaroslav Kysela <perex@suse.cz> Cc: Takashi Iwai <tiwai@suse.de> Cc: Greg KH <greg@kroah.com> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-03-27[PATCH] drivers/eisa/pci_eisa.c:pci_eisa_init() should be initAdrian Bunk
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:eisa_root_register from .text between 'pci_eisa_init' (at offset 0xabf670) and 'virtual_eisa_release' AFAIK a PCI to EISA bridge isn't anything hotpluggable, so pci_eisa_init() can become __init. Signed-off-by: Adrian Bunk <bunk@stusta.de> Cc: Greg KH <greg@kroah.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-03-27[PATCH] ntp: avoid time_offset overflowsjohn stultz
I've been seeing some odd NTP behavior recently on a few boxes and finally narrowed it down to time_offset overflowing when converted to SHIFT_UPDATE units (which was a side effect from my HZfreeNTP patch). This patch converts time_offset from a long to a s64 which resolves the issue. [tglx@linutronix.de: signedness fixes] Signed-off-by: John Stultz <johnstul@us.ibm.com> Cc: Roman Zippel <zippel@linux-m68k.org> Cc: john stultz <johnstul@us.ibm.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-03-27[PATCH] uml: use correct register file size everywhereJeff Dike
This patch uses MAX_REG_NR consistently to refer to the register file size. FRAME_SIZE isn't sufficient because on x86_64, it is smaller than the ptrace register file size. MAX_REG_NR was introduced as a consistent way to get the number of registers, but wasn't used everywhere it should be. When this causes a problem, it makes PTRACE_SETREGS fail on x86_64 because of a corrupted segment register value in the known-good register file. The patch also adds a register dump at that point in case there are any future problems here. Signed-off-by: Jeff Dike <jdike@linux.intel.com> Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-03-27[PATCH] uml: fix static linkingJeff Dike
During a static link, ld has started putting a .note section in the .uml.setup.init section. This has the result that the UML setups begin with 32 bytes of garbage and UML crashes immediately on boot. This patch creates a specific .note section for ld to drop this stuff into. Signed-off-by: Jeff Dike <jdike@linux.intel.com> Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-03-27[PATCH] drivers/spi/: fix section mismatchesAdrian Bunk
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:spi_register_master from .text between 'spi_bitbang_start' (at offset 0x84e11a) and 'bitbang_work' WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:spi_alloc_master from .text between 'butterfly_attach' (at offset 0x84e681) and 'at25_remove' WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:spi_new_device from .text between 'butterfly_attach' (at offset 0x84e7e4) and 'at25_remove' Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-03-27[PATCH] utsns: fix !CONFIG_UTS_NS behaviorSerge E. Hallyn
When CONFIG_UTS_NS=n, clone(CLONE_NEWUTS) quietly refuses. So correctly does not unshare a new uts namespace, but also does not return -EINVAL. Fix this to return -EINVAL so the caller knows his request was denied. Signed-off-by: Serge E. Hallyn <serue@us.ibm.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-03-27[PATCH] tty: minor merge correctionAlan Cox
Its now used.. because we added the new definitions so enabled all the goodies on i386 Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-03-27[PATCH] uml: fix epollJeff Dike
UML/x86_64 needs the same packing of struct epoll_event as x86_64. Signed-off-by: Jeff Dike <jdike@linux.intel.com> Cc: Davide Libenzi <davidel@xmailserver.org> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-03-27[PATCH] ISDN: fix BChannel_bh() call from isar_bh()Jiri Kosina
isar_bh() bh handler calls another (compatible) bh handler - BChannel_bh() - but passes struct BCState* instead of struct work_struct*, which seems wrong. Cc: Karsten Keil <kkeil@suse.de> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-03-27[PATCH] correct slow acpi_pm ratingjohn stultz
On Bob's machine clocksource is selecting PIT over the ACPI PM timer, because he has the PIIX4 bug. That bug drops the ACPI PM timers rating to the same as the PIT, so that's why you're getting the PIT. Realistically, the PIT is much slower then even the triple read ACPI PM, so the de-ranking code is probably dropping it too far. So don't drop ACPI PM quite so low if we see the PIIX4 bug. Signed-off-by: John Stultz <johnstul@us.ibm.com> Cc: Bob Tracy <rct@gherkin.frus.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Andi Kleen <ak@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-03-27[PATCH] generic_serial: fix decoding of baud rateDaniel Drake
Commit d720bc4b8fc5d6d179ef094908d4fbb5e436ffad partially removed a private implementation of baud speed decoding. However it doesn't seem to be complete: after the speed is decoded, it is still being used as an index to a local speed table (array overrun, no doubt). This was found by Graham Murray who noticed it caused a 2.6.19 regression with the SX driver: https://bugs.gentoo.org/170554 Signed-off-by: Daniel Drake <dsd@gentoo.org> Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Russell King <rmk@arm.linux.org.uk> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-03-27[PATCH] md: convert compile time warnings into runtime warningsNeilBrown
... still not sure why we need this .... Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-03-27[PATCH] md: clear the congested_fn when stopping a raid5NeilBrown
If this mddev and queue got reused for another array that doesn't register a congested_fn, this function would get called incorretly. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-03-27[PATCH] md: allow raid4 arrays to be reshapedNeilBrown
All that is missing the the function pointers in raid4_pers. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-03-27[PATCH] knfsd: nfsd4: remove superfluous cancel_delayed_work() callJ. Bruce Fields
This cancel_delayed_work call is called from a function that is only called from a piece of code that immediate follows a cancel and destruction of the workqueue, so it's clearly a mistake. Cc: Oleg Nesterov <oleg@tv-sign.ru> Signed-off-by: "J. Bruce Fields" <bfields@citi.umich.edu> Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-03-27[PATCH] knfsd: nfsd4: demote "clientid in use" printk to a dprintkBruce Fields
The reused clientid here is a more of a problem for the client than the server, and the client can report the problem itself if it's serious. Signed-off-by: "J. Bruce Fields" <bfields@citi.umich.edu> Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-03-27[PATCH] knfsd: nfsd4: fix inheritance flags on v4 ace derived from posix ↵Bruce Fields
default ace A regression introduced in the last set of acl patches removed the INHERIT_ONLY flag from aces derived from the posix acl. Fix. Signed-off-by: "J. Bruce Fields" <bfields@citi.umich.edu> Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-03-27[PATCH] knfsd: allow nfsd READDIR to return 64bit cookiesNeilBrown
->readdir passes lofft_t offsets (used as nfs cookies) to nfs3svc_encode_entry{,_plus}, but when they pass it on to encode_entry it becomes an 'off_t', which isn't good. So filesystems that returned 64bit offsets would lose. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-03-27[PATCH] Fix maxcpus=1 trigerring BUG() in cpufreqVenki Pallipadi
Ingo reported it on lkml in the thread "2.6.21-rc5: maxcpus=1 crash in cpufreq: kernel BUG at drivers/cpufreq/cpufreq.c:82!" This check added to remove_dev is symmetric to one in add_dev and handles callbacks for offline cpus cleanly. Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Acked-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-03-27KVM: always reload segment selectorsIngo Molnar
failed VM entry on VMX might still change %fs or %gs, thus make sure that KVM always reloads the segment selectors. This is crutial on both x86 and x86_64: x86 has __KERNEL_PDA in %fs on which things like 'current' depends and x86_64 has 0 there and needs MSR_GS_BASE to work. Signed-off-by: Ingo Molnar <mingo@elte.hu>
2007-03-27KVM: Prevent system selectors leaking into guest on real->protected mode ↵Avi Kivity
transition on vmx Intel virtualization extensions do not support virtualizing real mode. So kvm uses virtualized vm86 mode to run real mode code. Unfortunately, this virtualized vm86 mode does not support the so called "big real" mode, where the segment selector and base do not agree with each other according to the real mode rules (base == selector << 4). To work around this, kvm checks whether a selector/base pair violates the virtualized vm86 rules, and if so, forces it into conformance. On a transition back to protected mode, if we see that the guest did not touch a forced segment, we restore it back to the original protected mode value. This pile of hacks breaks down if the gdt has changed in real mode, as it can cause a segment selector to point to a system descriptor instead of a normal data segment. In fact, this happens with the Windows bootloader and the qemu acpi bios, where a protected mode memcpy routine issues an innocent 'pop %es' and traps on an attempt to load a system descriptor. "Fix" by checking if the to-be-restored selector points at a system segment, and if so, coercing it into a normal data segment. The long term solution, of course, is to abandon vm86 mode and use emulation for big real mode. Signed-off-by: Avi Kivity <avi@qumranet.com>
2007-03-27V4L/DVB (5472): Isl6421: don't reference freed memoryThomas Viehweger
After freeing a block there should be no reference to this block. Signed-off-by: Thomas Viehweger <Thomas.Viehweger@marconi.com> Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2007-03-27V4L/DVB (5441): Saa7146: Fix allocation of clipping memoryOliver Endriss
Olaf Hering pointed out that SAA7146_CLIPPING_MEM would become very large for PAGE_SIZE > 4K. In fact, the number of clipping windows is limited to 16, and calculate_clipping_registers_rect() does not use more than 256 bytes. SAA7146_CLIPPING_MEM adjusted accordingly. Thanks-to: Olaf Hering <olaf@aepfle.de> Acked-by: Michael Hunold <hunold@linuxtv.org> Signed-off-by: Oliver Endriss <o.endriss@gmx.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2007-03-27V4L/DVB (5421): Fix suspend/resume in msp3400 and tunerJean Delvare
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2007-03-27V4L/DVB (5415): Msp_attach must return 0 if no msp3400 was found.Hans Verkuil
Returning -1 causes the probe to stop, but it should just continue instead. Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2007-03-27V4L/DVB (5408): Fix SECAM handling on saa7115Mauro Carvalho Chehab
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2007-03-27V4L/DVB (5400): Core: fix several locking related problemsSimon Arlott
Fix several instances of dvb-core functions using mutex_lock_interruptible and returning -ERESTARTSYS where the calling function will either never retry or never check the return value. These cause a race condition with dvb_dmxdev_filter_free and dvb_dvr_release, both of which are filesystem release functions whose return value is ignored and will never be retried. When this happens it becomes impossible to open dvr0 again (-EBUSY) since it has not been released properly. Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-By: Johannes Stezenbach <js@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2007-03-27V4L/DVB (5390): Radio: Fix error in Kbuild fileTrent Piepho
All the radio drivers need video_dev, but they were depending on VIDEO_DEV!=n. That meant that one could try to compile the driver into the kernel when VIDEO_DEV=m, which will not work. If video_dev is a module, then the radio drivers must be modules too. Signed-off-by: Trent Piepho <xyzzy@speakeasy.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
generated by cgit v1.2.3 (git 2.25.1) at 2025-01-01 19:05:57 +0000