| Age | Commit message (Collapse) | Author |
|---|
|
This seems as reasonable assumption and gets some SNI machines to work
which currently must rely on the cp0 counter as clocksource.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
- suppress master aborts during config read
- set io_map_base
- only fixup end of iomem resource to avoid failing request_resource
in serial driver
- killed useless setting of crime_int bit, which caused wrong interrupts
- use physcial address for serial port platform device and let 8250
driver do the ioremap
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
WARNING: vmlinux.o(.text+0x1ca608): Section mismatch: reference to
.init.text: add_wired_entry (between 'config_access' and 'config_read')
by refactoring the code calling add_wired_entry() from config_access() to
a separate function which is called from aau1x_pci_setup(). While at it:
- make some unnecassarily global variables 'static';
- fix the letter case, whitespace, etc. in the comments...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
CONFIG_NO_HZ, CONFIG_HIGH_RES_TIMERS should be selected in "Kernel
type" menu, not in "CPU selection" menu.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
|
|
make randconfig bootup testing found that the cpufreq code
crashes on bootup, if the powernow-k8 driver is enabled and
if maxcpus=1 passed on the boot line to a !CONFIG_HOTPLUG_CPU
kernel.
First lockdep found out that there's an inconsistent unlock
sequence:
=====================================
[ BUG: bad unlock balance detected! ]
-------------------------------------
swapper/1 is trying to release lock (&per_cpu(cpu_policy_rwsem, cpu)) at:
[<ffffffff806ffd8e>] unlock_policy_rwsem_write+0x3c/0x42
but there are no more locks to release!
Call Trace:
[<ffffffff806ffd8e>] unlock_policy_rwsem_write+0x3c/0x42
[<ffffffff80251c29>] print_unlock_inbalance_bug+0x104/0x12c
[<ffffffff80252f3a>] mark_held_locks+0x56/0x94
[<ffffffff806ffd8e>] unlock_policy_rwsem_write+0x3c/0x42
[<ffffffff807008b6>] cpufreq_add_dev+0x2a8/0x5c4
...
then shortly afterwards the cpufreq code crashed on an assert:
------------[ cut here ]------------
kernel BUG at drivers/cpufreq/cpufreq.c:1068!
invalid opcode: 0000 [1] SMP
[...]
Call Trace:
[<ffffffff805145d6>] sysdev_driver_unregister+0x5b/0x91
[<ffffffff806ff520>] cpufreq_register_driver+0x15d/0x1a2
[<ffffffff80cc0596>] powernowk8_init+0x86/0x94
[...]
---[ end trace 1e9219be2b4431de ]---
the bug was caused by maxcpus=1 bootup, which brought up the
secondary core as !cpu_online() but !cpu_is_offline() either,
which on on !CONFIG_HOTPLUG_CPU is always 0 (include/linux/cpu.h):
/* CPUs don't go offline once they're online w/o CONFIG_HOTPLUG_CPU */
static inline int cpu_is_offline(int cpu) { return 0; }
but the cpufreq code uses cpu_online() and cpu_is_offline() in
a mixed way - the low-level drivers use cpu_online(), while
the cpufreq core uses cpu_is_offline(). This opened up the
possibility to add the non-initialized sysdev device of the
secondary core:
cpufreq-core: trying to register driver powernow-k8
cpufreq-core: adding CPU 0
powernow-k8: BIOS error - no PSB or ACPI _PSS objects
cpufreq-core: initialization failed
cpufreq-core: adding CPU 1
cpufreq-core: initialization failed
which then blew up. The fix is to make cpu_is_offline() always
the negation of cpu_online(). With that fix applied the kernel
boots up fine without crashing:
Calling initcall 0xffffffff80cc0510: powernowk8_init+0x0/0x94()
powernow-k8: Found 1 AMD Athlon(tm) 64 X2 Dual Core Processor 3800+ processors (1 cpu cores) (version 2.20.00)
powernow-k8: BIOS error - no PSB or ACPI _PSS objects
initcall 0xffffffff80cc0510: powernowk8_init+0x0/0x94() returned -19.
initcall 0xffffffff80cc0510 ran for 19 msecs: powernowk8_init+0x0/0x94()
Calling initcall 0xffffffff80cc328f: init_lapic_nmi_sysfs+0x0/0x39()
We could fix this by making CPU enumeration aware of max_cpus, but that
would be more fragile IMO, and the cpu_online(cpu) != cpu_is_offline(cpu)
possibility was quite confusing and a continuous source of bugs too.
Most distributions have kernels with CPU hotplug enabled, so this bug
remained hidden for a long time.
Bug forensics:
The broken cpu_is_offline() API variant was introduced via:
commit a59d2e4e6977e7b94e003c96a41f07e96cddc340
Author: Rusty Russell <rusty@rustcorp.com.au>
Date: Mon Mar 8 06:06:03 2004 -0800
[PATCH] minor cleanups for hotplug CPUs
( this predates linux-2.6.git, this commit is available from Thomas's
historic git tree. )
Then 1.5 years later the cpufreq code made use of it:
commit c32b6b8e524d2c337767d312814484d9289550cf
Author: Ashok Raj <ashok.raj@intel.com>
Date: Sun Oct 30 14:59:54 2005 -0800
[PATCH] create and destroy cpufreq sysfs entries based on cpu notifiers
+ if (cpu_is_offline(cpu))
+ return 0;
which is a correct use of the subtly broken new API. v2.6.15 then
shipped with this bug included.
then it took two more years for random-kernel qa to hit it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
not sleeping for every codec read/write but doing a short udelay and
a conditional reschedule has cut suspend+resume latency by about 1
second on my T60.
The patch also fixes the unexpected codec-connection errors that
happen more often in the new power-save mode:
http://lkml.org/lkml/2007/11/8/255
http://bugzilla.kernel.org/show_bug.cgi?id=9332
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
unfortunately 32 bit apps don't see the joysticks on a 64 bit system.
this prevents one playing X-Plane (http://www.x-plane.com/) or other
32-bit games with joysticks.
this is a known issue, and already raised several times:
http://readlist.com/lists/vger.kernel.org/linux-kernel/28/144411.html
http://www.brettcsmith.org/wiki/wiki.cgi?action=browse&diff=1&id=OzyComputer/Joystick
unfortunately this is still not fixed in the mainline kernel.
it would be nice to have this fixed, so that people can play these games
without having to patch their kernel.
the following patch solves the problem on 2.6.22.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This reverts commit ac40532ef0b8649e6f7f83859ea0de1c4ed08a19, which gets
us back the original cleanup of 6f5391c283d7fdcf24bf40786ea79061919d1e1d.
It turns out that the bug that was triggered by that commit was
apparently not actually triggered by that commit at all, and just the
testing conditions had changed enough to make it appear to be due to it.
The real problem seems to have been found by Peter Osterlund:
"pktcdvd sets it [block device size] when opening the /dev/pktcdvd
device, but when the drive is later opened as /dev/scd0, there is
nothing that sets it back. (Btw, 40944 is possible if the disk is a
CDRW that was formatted with "cdrwtool -m 10236".)
The problem is that pktcdvd opens the cd device in non-blocking mode
when pktsetup is run, and doesn't close it again until pktsetup -d is
run. The effect is that if you meanwhile open the cd device,
blkdev.c:do_open() doesn't call bd_set_size() because
bdev->bd_openers is non-zero."
In particular, to repeat the bug (regardless of whether commit
6f5391c283d7fdcf24bf40786ea79061919d1e1d is applied or not):
" 1. Start with an empty drive.
2. pktsetup 0 /dev/scd0
3. Insert a CD containing an isofs filesystem.
4. mount /dev/pktcdvd/0 /mnt/tmp
5. umount /mnt/tmp
6. Press the eject button.
7. Insert a DVD containing a non-writable filesystem.
8. mount /dev/scd0 /mnt/tmp
9. find /mnt/tmp -type f -print0 | xargs -0 sha1sum >/dev/null
10. If the DVD contains data beyond the physical size of a CD, you
get I/O errors in the terminal, and dmesg reports lots of
"attempt to access beyond end of device" errors."
which in turn is because the nested open after the media change won't
cause the size to be set properly (because the original open still holds
the block device, and we only do the bd_set_size() when we don't have
other people holding the device open).
The proper fix for that is probably to just do something like
bdev->bd_inode->i_size = (loff_t)get_capacity(disk)<<9;
in fs/block_dev.c:do_open() even for the cases where we're not the
original opener (but *not* call bd_set_size(), since that will also
change the block size of the device).
Cc: Peter Osterlund <petero2@telia.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The SCSI SRP transport class currently iterates over all children
devices of the host that is being removed in srp_remove_host(). However,
not all of those children were created by the SRP transport, and
removing them will cause corruption and an oops when their creator tries
to remove them.
Signed-off-by: David Dillow <dillowda@ornl.gov>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
[ISDN]: i4l: Fix DLE handling for i4l-audio
[ISDN] i4l: 'NO CARRIER' message lost after ldisc flush
[CONNECTOR]: Return proper error code in cn_call_callback()
[INET]: Fix netdev renaming and inet address labels
[CASSINI]: Bump driver version and release date.
[CASSINI]: Fix two obvious NAPI bugs.
[CASSINI]: Set skb->truesize properly on receive packets.
[CASSINI]: Program parent Intel31154 bridge when necessary.
[CASSINI]: Revert 'dont touch page_count'.
[CASSINI]: Fix endianness bug.
[XFRM]: Do not define km_migrate() if !CONFIG_XFRM_MIGRATE
[X25]: Add missing x25_neigh_put
|
|
The DLE handling in i4l-audio seems to be broken.
It produces spurious DLEs so asterisk 1.2.24 with chan_modem_i4l
gets irritated, the error message is:
"chan_modem_i4l.c:450 i4l_read: Value of escape is ^ (17)".
-> There shouldn't be a DLE-^.
If a spurious DLE-ETX occurs, the audio connection even dies.
I use a "AVM Fritz!PCI" isdn card.
I found two issues that only appear if ISDN_AUDIO_SKB_DLECOUNT(skb) > 0:
- The loop in isdn_tty.c:isdn_tty_try_read() doesn't escape a DLE if it's
the last character.
- The loop in isdn_common.c:isdn_readbchan_tty() doesn't copy its characters,
it only remembers the last one ("last = *p;").
Compare it with the loop in isdn_common.c:isdn_readbchan(), that *does*
copy them ("*cp++ = *p;") correctly.
The special handling of the "last" character made it more difficult.
I compared it to linux-2.4.19: There was no "last"-handling and both loops
did escape and copy all characters correctly.
Signed-off-by: Matthias Goebl <matthias.goebl@goebl.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ISDN tty layer doesn't produce a 'NO CARRIER' message after hangup.
I suppose it broke when tty_buffer_flush() has been added to
tty_ldisc_flush() in the commit below.
For isdn_tty_modem_result(RESULT_NO_CARRIER..) the
message inserted via isdn_tty_at_cout() -> tty_insert_flip_char()
is flushed immediately by tty_ldisc_flush() -> tty_buffer_flush().
More annoyingly, the audio abort sequence DLE-ETX is also lost.
This patch fixes only active audio connections, because I assume that nobody
changes the line discipline for audio.
For non-audio connections the problem remains.
Maybe we can remove the tty_ldisc_flush() in isdn_tty_modem_result()
at all because it's done at tty_close?
On Mon, May 07, 2007 at 04:05:57PM -0500, Paul Fulghum wrote:
> Flush the tty flip buffer when the line discipline
> input queue is flushed, including the user call
> tcflush(TCIFLUSH/TCIOFLUSH). This prevents unexpected
> stale data after a user application calls tcflush().
>
> Cc: Alan Cox <alan@lxorguk.org.uk>
> Cc: Antonino Ingargiola <tritemio@gmail.com>
> Signed-off-by: Paul Fulghum <paulkf@microgate.com>
>
> --- a/drivers/char/tty_io.c 2007-05-04 05:46:55.000000000 -0500
> +++ b/drivers/char/tty_io.c 2007-05-05 03:23:46.000000000 -0500
> @@ -1240,6 +1263,7 @@ void tty_ldisc_flush(struct tty_struct *
> ld->flush_buffer(tty);
> tty_ldisc_deref(ld);
> }
> + tty_buffer_flush(tty);
[..]
Signed-off-by: Matthias Goebl <matthias.goebl@goebl.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Error code should be set to EINVAL instead of ENODEV if !queue_work().
There's another call of queue_work() which may set err to EINVAL.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When re-naming an interface, the previous secondary address
labels get lost e.g.
$> brctl addbr foo
$> ip addr add 192.168.0.1 dev foo
$> ip addr add 192.168.0.2 dev foo label foo:00
$> ip addr show dev foo | grep inet
inet 192.168.0.1/32 scope global foo
inet 192.168.0.2/32 scope global foo:00
$> ip link set foo name bar
$> ip addr show dev bar | grep inet
inet 192.168.0.1/32 scope global bar
inet 192.168.0.2/32 scope global bar:2
Turns out to be a simple thinko in inetdev_changename() - clearly we
want to look at the address label, rather than the device name, for
a suffix to retain.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1) close should do napi_disable() not napi_enable
2) remove unused local var 'todo'
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb->truesize was not being incremented at all to
reflect the page based data added to RX SKBs.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts changeset fa4f0774d7c6cccb4d1fda76b91dd8eddcb2dd6a
([CASSINI]: dont touch page_count) because it breaks the driver.
The local page counting added by this changeset did not account
for the asynchronous page count changes done by kfree_skb()
and friends.
The change adds extra atomics and on top of it all appears to be
totally unnecessary as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Nick Piggin <npiggin@suse.de>
|
|
Here's proposed fix for RX checksum handling in cassini; it affects
little-endian working with half-duplex gigabit, but obviously needs
testing on big-endian too.
The problem is, we need to convert checksum to fixed-endian *before*
correcting for (unstripped) FCS. On big-endian it won't matter
(conversion is no-op), on little-endian it will, but only if FCS is
not stripped by hardware; i.e. in half-duplex gigabit mode when
->crc_size is set.
cassini.c part is that fix, cassini.h one consists of trivial
endianness annotations. With that applied the sucker is endian-clean,
according to sparse.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In include/net/xfrm.h we find :
#ifdef CONFIG_XFRM_MIGRATE
extern int km_migrate(struct xfrm_selector *sel, u8 dir, u8 type,
struct xfrm_migrate *m, int num_bundles);
...
#endif
We can also guard the function body itself in net/xfrm/xfrm_state.c
with same condition.
(Problem spoted by sparse checker)
make C=2 net/xfrm/xfrm_state.o
...
net/xfrm/xfrm_state.c:1765:5: warning: symbol 'km_migrate' was not declared. Should it be static?
...
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function x25_get_neigh increments a reference count. At the point of
the second goto out, the result of calling x25_get_neigh is only stored in
a local variable, and thus no one outside the function will be able to
decrease the reference count. Thus, x25_neigh_put should be called before
the return in this case.
The problem was found using the following semantic match.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T,T1,T2;
identifier E;
statement S;
expression x1,x2,x3;
int ret;
@@
T E;
...
* if ((E = x25_get_neigh(...)) == NULL)
S
... when != x25_neigh_put(...,(T1)E,...)
when != if (E != NULL) { ... x25_neigh_put(...,(T1)E,...); ...}
when != x1 = (T1)E
when != E = x3;
when any
if (...) {
... when != x25_neigh_put(...,(T2)E,...)
when != if (E != NULL) { ... x25_neigh_put(...,(T2)E,...); ...}
when != x2 = (T2)E
(
* return;
|
* return ret;
)
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Montecito and Montvale behaves slightly differently than previous
Itanium processors, resulting in the MCA due to a failed PIO read
to sometimes surfacing outside the nofault code. This code is
based on discussions with Intel CPU architects and verified at
customer sites.
Signed-off-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
I neglected to send Tony the most recent version of the
patch ("Fix Altix BTE error return status") applied
as commit: 64135fa97ce016058f95345425a9ebd04ee1bd2a
This patch gets it up to date. Without this patch
on shub2, if there is no error xpcBteUnmappedError is
returned instead of xpcSuccess.
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/srp: Fix list corruption/oops on module reload
|
|
The console is now by default in UTF-8 mode. Fix the documentation on
the default value, so that we can explain behaviour that otherwise
causes bug-reports like this:
http://bugzilla.kernel.org/show_bug.cgi?id=9319
Also add the needed "vt." prefix, so that the boot-time config options
to switch back to the legacy 8-bit mode is actually documented
correctly.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* 'release' of git://lm-sensors.org/kernel/mhoffman/hwmon-2.6:
hwmon: (w83627ehf) Be more careful when changing VID input level
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched:
sched: fix gcc warnings
|
|
* git://git.linux-nfs.org/pub/linux/nfs-2.6:
NFSv4: Fix open_to_lock_owner sequenceid allocation...
NFSv4: nfs4_open_confirm must not set the open_owner as confirmed on error
NFS: add newline to kernel warning message in auth_gss code
NFSv4: Fix circular locking dependency in nfs4_kill_renewd
NFS: Fix a possible Oops in fs/nfs/super.c
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] scsi_sysfs: restore prep_fn when ULD is removed
|
|
Add a missing call to srp_remove_host() in srp_remove_one() so that we
don't leak SRP transport class list entries.
Tested-by: David Dillow <dillowda@ornl.gov>
Acked-by: FUJITA Tomonori <tomof@acm.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
NFSv4 file locking is currently completely broken since it doesn't respect
the OPEN sequencing when it is given an unconfirmed lock_owner and needs to
do an open_to_lock_owner. Worse: it breaks the sunrpc rules by doing a
GFP_KERNEL allocation inside an rpciod callback.
Fix is to preallocate the open seqid structure in nfs4_alloc_lockdata if we
see that the lock_owner is unconfirmed.
Then, in nfs4_lock_prepare() we wait for either the open_seqid, if
the lock_owner is still unconfirmed, or else fall back to waiting on the
standard lock_seqid.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
RFC3530 states that the open_owner is confirmed if and only if the client
sends an OPEN_CONFIRM request with the appropriate sequence id and stateid
within the lease period.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Add newline to kernel warning message in gss_create().
Signed-off-by: James Morris <jmorris@namei.org>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Erez Zadok reports:
=======================================================
[ INFO: possible circular locking dependency detected ]
2.6.24-rc6-unionfs2 #80
-------------------------------------------------------
umount.nfs4/4017 is trying to acquire lock:
(&(&clp->cl_renewd)->work){--..}, at: [<c0223e53>]
__cancel_work_timer+0x83/0x17f
but task is already holding lock:
(&clp->cl_sem){----}, at: [<f8879897>] nfs4_kill_renewd+0x17/0x29 [nfs]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&clp->cl_sem){----}:
[<c0230699>] __lock_acquire+0x9cc/0xb95
[<c0230c39>] lock_acquire+0x5f/0x78
[<c0397cb8>] down_read+0x3a/0x4c
[<f88798e6>] nfs4_renew_state+0x1c/0x1b8 [nfs]
[<c0223821>] run_workqueue+0xd9/0x1ac
[<c0224220>] worker_thread+0x7a/0x86
[<c0226b49>] kthread+0x3b/0x62
[<c02033a3>] kernel_thread_helper+0x7/0x10
[<ffffffff>] 0xffffffff
-> #0 (&(&clp->cl_renewd)->work){--..}:
[<c0230589>] __lock_acquire+0x8bc/0xb95
[<c0230c39>] lock_acquire+0x5f/0x78
[<c0223e87>] __cancel_work_timer+0xb7/0x17f
[<c0223f5a>] cancel_delayed_work_sync+0xb/0xd
[<f887989e>] nfs4_kill_renewd+0x1e/0x29 [nfs]
[<f885a8f6>] nfs_free_client+0x37/0x9e [nfs]
[<f885ab20>] nfs_put_client+0x5d/0x62 [nfs]
[<f885ab9a>] nfs_free_server+0x75/0xae [nfs]
[<f8862672>] nfs4_kill_super+0x27/0x2b [nfs]
[<c0258aab>] deactivate_super+0x3f/0x51
[<c0269668>] mntput_no_expire+0x42/0x67
[<c025d0e4>] path_release_on_umount+0x15/0x18
[<c0269d30>] sys_umount+0x1a3/0x1cb
[<c0269d71>] sys_oldumount+0x19/0x1b
[<c02026ca>] sysenter_past_esp+0x5f/0xa5
[<ffffffff>] 0xffffffff
Looking at the code, it would seem that taking the clp->cl_sem in
nfs4_kill_renewd is completely redundant, since we're already guaranteed to
have exclusive access to the nfs_client (we're shutting down).
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Sigh... commit 4584f520e1f773082ef44ff4f8969a5d992b16ec (NFS: Fix NFS
mountpoint crossing...) had a slight flaw: server can be NULL if sget()
returned an existing superblock.
Fix the fix by dereferencing s->s_fs_info.
Thanks to Coverity/Adrian Bunk and Frank Filz for spotting the bug.
(See http://bugzilla.kernel.org/show_bug.cgi?id=9647)
Also add in the same namespace Oops fix for NFSv4 in both the mountpoint
crossing case, and the referral case.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
The VID input level change has been reported to cause trouble. Be more
careful in this respect:
* Only change the level on the W83627EHF/EHG. The W83627DHG is more
complex in this respect.
* Don't change the level if the VID pins are in output mode.
* Only set the level to TTL if VRM 9.x is used.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
|
|
The previous commit missed one use of "may_attach()" that had been
renamed to __ptrace_may_attach(). Tssk, tssk, Al.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Contents of /proc/*/maps is sensitive and may become sensitive after
open() (e.g. if target originally shares our ->mm and later does exec
on suid-root binary).
Check at read() (actually, ->start() of iterator) time that mm_struct
we'd grabbed and locked is
- still the ->mm of target
- equal to reader's ->mm or the target is ptracable by reader.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This reverts commit 6f5391c283d7fdcf24bf40786ea79061919d1e1d ("[SCSI]
Get rid of scsi_cmnd->done") that was supposed to be a cleanup commit,
but apparently it causes regressions:
Bug 9370 - v2.6.24-rc2-409-g9418d5d: attempt to access beyond end of device
http://bugzilla.kernel.org/show_bug.cgi?id=9370
this patch should be reintroduced in a more split-up form to make
testing of it easier.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Matthew Wilcox <matthew@wil.cx>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Both SLUB and SLAB really did almost exactly the same thing for
/proc/slabinfo setup, using duplicate code and per-allocator #ifdef's.
This just creates a common CONFIG_SLABINFO that is enabled by both SLUB
and SLAB, and shares all the setup code. Maybe SLOB will want this some
day too.
Reviewed-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
A recent bug report:
http://bugzilla.kernel.org/show_bug.cgi?id=9674
Was caused because the ULDs now set their own prep functions, but
don't necessarily reset the prep function back to the SCSI default
when they are removed. This leads to panics if commands are sent to
the device after the module is removed because the prep_fn is still
pointing to the old module code. The fix for this is to implement a
bus remove method that resets the prep_fn pointer correctly before
calling the ULD specific driver remove method.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
We need to register slabinfo to procfs when CONFIG_SLUB is enabled to
make the file actually visible to user-space.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Fix build failure on Cell when CONFIG_SPU_FS=y
|
|
Commit aed3a8c9bb1a8623a618232087c5ff62718e3b9a introduced a
definition of notify_spus_active in .../cell/spu_syscalls.c, and
another definition under #ifndef MODULE in .../cell/spufs/sched.c.
The latter is not necessary and causes the build to fail when
CONFIG_SPU_FS=y, so this removes it. It also removes the export
of do_notify_spus_active, which is unnecessary.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86:
x86: fix asm-x86/msr.h for user-space export
x86: fix asm-x86/byteorder.h for userspace export
|
|
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
leds: Fix locomo LED driver oops
leds: Fix leds_list_lock locking issues
|
|
This adds a read-only /proc/slabinfo file on SLUB, that makes slabtop work.
[ mingo@elte.hu: build fix. ]
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
After 17d57a9206b4de6ad082ac9f2d2346985abbd2aa ("x86: fix x86-32 early
fixmap initialization.") removing lg.ko caused a printk from vunmap:
mm/memory.c:115: bad pgd 004b3027.
On the second use after module load, the kernel crashes.
This fixes the immediate problem (accessed and dirty bits not set as
expected in pmd_none_or_clear_bad). I can't see why this would cause
a crash, but I haven't been able to reproduce it once this is applied.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
