| Age | Commit message (Collapse) | Author |
|---|
|
For I/O DLPAR to work properly, the kernel needs to allow for dynamic
assignment of the irq field of the pci_dev structure upon dynamic bus
addition. This patch moves the assignment of that field from
pSeries_final_fixup() to pcibios_fixup_bus(), which enables dynamic
assignment for the children of a newly added bus.
Currently, pci_devs receive their irq numbers in one of two ways. The
irq line is either read at boot for all pci_devs, or read by the rpaphp
module at slot enable time. The latter is no longer sufficient for
DLPAR addition of slots that don't qualify as PCI-hotplug capable.
This solution handles the cases of boot and dynamic add.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This patch corrects the printing of progress indicators to the op
panel on p/iSeries ppc64 systems. Each discrete reference code should
begin with a form feed char to clear the op panel, and the first and
second lines should be separated with a CR/LF sequence. Padding with
spaces is not necessary.
Also, capitalize the hex value printed on the first line, to be
consistent with the values printed by firmware, service processor,
etc.
It turns out that there's an ibm,form-feed property; this patch uses
it in the pSeries-specific progress routine. This patch also checks
the number of rows and the specific width of each row (the second row
on power5 systems can actually hold 80 characters). If the displayed
text is too wide for the physical display, it can be viewed in the ASM
menus, or by selecting option 14 on the op panel.
Signed-off-by: Mike Strosaker <strosake@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Implementation of software load support for the BE iommu. This is very
different from other iommu code on ppc64, since we only do a static mapping.
The mapping is currently hardcoded but should really be read from the
firmware, but they don't set up the device nodes yet. There is a single
512MB DMA window for PCI, USB and ethernet at 0x20000000 for our RAM.
The Cell processor can put the I/O page table either in memory like
the hashed page table (hardware load) or have the operating system
write the entries into memory mapped CPU registers (software load).
I use the software load mechanism because I know that all I/O page
table entries for the amount of installed physical memory fit into
the IO TLB cache. At the point when we get machines with more than
4GB of installed memory, we can either use hardware I/O page table
access like the other platforms do or dynamically update the I/O
TLB entries when a page fault occurs in the I/O subsystem.
The software load can then use the macros that I have implemented
for the static mapping in order to do the TLB cache updates.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Add support for the integrated interrupt controller on BPA
CPUs. There is one of those for each SMT thread.
The mapping of interrupt numbers to HW interrupt sources
is described in arch/ppc64/kernel/bpa_iic.h.
This version hardcodes the 'Spider' chip as the secondary
interrupt controller. That is not really generic for the
architecture, but at the moment it is the only secondary
PIC that exists.
A little more work will be needed on this as soon as
we have boards with multiple external interrupt controllers.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This adds the basic support for running on BPA machines.
So far, this is only the IBM workstation, and it will
not run on others without a little more generalization.
It should be possible to configure a kernel for any
combination of CONFIG_PPC_BPA with any of the other
multiplatform targets.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Add a watchdog using the RTAS OS surveillance service. This is
provided as a simpler alternative to rtasd. The added value
is that it works with standard watchdog client programs and
can therefore also do user space monitoring.
On BPA, rtasd is not really useful because the hardware does
not have much to report with event-scan.
The driver should also work on other platforms that support
the OS surveillance rtas calls.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The firmware provides the location and size of the nvram
in the device tree, so it does not really contain any
hardware specific bits and could be used on other
machines as well.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The pSeries_progress function is called from some places in the rtas code,
which may also be used by non-pSeries platforms.
Though pSeries is currently the only platform type that implements
display-character, the code is actually generic enough to be part of
the rtas subsystem.
I hit a bug here because the generic rtas code tried calling ppc_md.progress,
which points to an __init function on most platforms.
We could also clear the ppc_md.progress pointer when freeing the init memory
to make it more explicit that ppc_md.progress must not be called after
bootup.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
BPA is using rtas for PCI but should not be confused by
pSeries code. This also avoids some #ifdefs. Other
platforms that want to use rtas_pci.c could create
their own platform_pci.c with platform specific fixups.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The rtc rtas functions are not pSeries specific but can
also be used by BPA and other SLOF based platforms
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
pSeries and maple have almost the same code for calibrate_decr,
and BPA would need yet another copy. Instead, I'm moving the
code to arch/ppc64/kernel/time.c.
Some of the related declarations were missing from header
files, so I'm moving those as well.
It makes sense to merge this with the pmac function of the
same name, so we end up having just one implemetation for
iSeries and one for Open Firmware based machines.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
|
|
|
|
Since meminfo.bank[] array contains page-aligned start/size, we
no longer need to explicitly round up/down the addresses when
converting to PFNs.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Ensure that meminfo.bank[] array contains page-aligned start/size
information.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Convert dmabounce.c to use list_for_each_entry() instead of
list_for_each() + list_entry().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Adding support for MPC8548 w/o PCI support, broke building MPC8555 CDS
by trying to remove a loop variable that was used when PCI is enabled.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org)
|
|
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
This shows up on running tar over NFSv4.
Signed-off-by: Manoj Naik <manoj@almaden.ibm.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Request RDATTR_ERROR as an attribute in readdir to distinguish between a
directory being within an absent filesystem or one (or more) of its entries.
Signed-off-by: Manoj Naik <manoj@almaden.ibm.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Ensure that lock owner structures are not released prematurely.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
If the lock blocks, the server may send us a GRANTED message that
races with the reply to our LOCK request. Make sure that we catch
the GRANTED by queueing up our request on the nlm_blocked list
before we send off the first LOCK rpc call.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
fl_release_private
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
efficient.
Basically copies the VFS's method for tracking writebacks and applies
it to the struct nfs_page.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Use stable writes if we can see that we are only going to put a single
write on the wire.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Even if the file is open for writes.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Unless we're doing O_APPEND writes, we really don't care about revalidating
the file length. Just make sure that we catch any page cache invalidations.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Instead of looking at whether or not the file is open for writes before
we accept to update the length using the server value, we should rather
be looking at whether or not we are currently caching any writes.
Failure to do so means in particular that we're not updating the file
length correctly after obtaining a POSIX or BSD lock.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
If we do not hold a valid stateid that is open for writes, there is little
point in doing an extra open of the file, as the RFC does not appear to
mandate this...
Make setattr use the correct stateid if we're holding mandatory byte
range locks.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
NFSv3 currently returns the unsigned 64-bit cookie directly to
userspace. The following patch causes the kernel to generate
loff_t offsets for the benefit of userland.
The current server-generated READDIR cookie is cached in the
nfs_open_context instead of in filp->f_pos, so we still end up work
correctly under directory insertions/deletion.
Signed-off-by: Olivier Galibert <galibert@pobox.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Make the socket transport kick the event queue to start socket connects
immediately. This should improve responsiveness of applications that are
sensitive to slow mount operations (like automounters).
We are now also careful to cancel the connect worker before destroying
the xprt. This eliminates a race where xprt_destroy can finish before
the connect worker is even allowed to run.
Test-plan:
Destructive testing (unplugging the network temporarily). Connectathon
with UDP and TCP. Hard-code impossibly small connect timeout.
Version: Fri, 29 Apr 2005 15:32:01 -0400
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
When the network layer reports a connection close, the RPC task
waiting to reconnect should be notified so it can retry immediately
instead of waiting for the normal connection establishment timeout.
This reverts a change made in 2.6.6 as part of adding client support
for RPC over TCP socket idle timeouts.
Test-plan:
Destructive testing with NFS over TCP mounts.
Version: Fri, 29 Apr 2005 15:31:46 -0400
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Cancel autodisconnect requests inside xprt_transmit() in order to avoid
races.
Use more efficient del_singleshot_timer_sync()
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
For internal purposes, the rpc_clnt_sigmask() call is replaced by
a call to rpc_task_sigmask(), which ensures that the current task
sigmask respects both the client cl_intr flag and the per-task NOINTR flag.
Problem noted by Jiaying Zhang.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
The changeset "trond.myklebust@fys.uio.no|ChangeSet|20050322152404|16979"
(RPC: Ensure XDR iovec length is initialized correctly in call_header)
causes the NFSv4 callback code to BUG() due to an incorrectly initialized
scratch buffer.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
From: Reuben Farrelly <reuben-lkml@reub.net>
With gcc-4.0:
fs/nfs/nfs4proc.c:2976: error: static declaration of
'nfs4_file_inode_operations' follows non-static declaration
fs/nfs/nfs4_fs.h:179: error: previous declaration of
'nfs4_file_inode_operations' was here
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Older gcc's don't like this.
fs/nfs/nfs4proc.c:2194: field `data' has incomplete type
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
The Coverity checker noticed that such a simplification was possible.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
* Pointer arithmetic bug: p is in word units. This fixes a memory
corruption with big acls.
* Initialize pg_class to prevent a NULL pointer access.
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Initialize the inode cache values correctly.
Clean up __nfs3_forget_cached_acls()
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Attach acls to inodes in the icache to avoid unnecessary GETACL RPC
round-trips. As long as the client doesn't retrieve any acls itself, only the
default acls of exiting directories and the default and access acls of new
directories will end up in the cache, which preserves some memory compared to
always caching the access and default acl of all files.
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Acked-by: Olaf Kirch <okir@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
NFSv3 has no concept of a umask on the server side: The client applies
the umask locally, and sends the effective permissions to the server.
This behavior is wrong when files are created in a directory that has a
default ACL. In this case, the umask is supposed to be ignored, and
only the default ACL determines the file's effective permissions.
Usually its the server's task to conditionally apply the umask. But
since the server knows nothing about the umask, we have to do it on the
client side. This patch tries to fetch the parent directory's default
ACL before creating a new file, computes the appropriate create mode to
send to the server, and finally sets the new file's access and default
acl appropriately.
Many thanks to Buck Huppmann <buchk@pobox.com> for sending the initial
version of this patch, as well as for arguing why we need this change.
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Acked-by: Olaf Kirch <okir@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
This adds acl support fo nfs clients via the NFSACL protocol extension, by
implementing the getxattr, listxattr, setxattr, and removexattr iops for the
system.posix_acl_access and system.posix_acl_default attributes. This patch
implements a dumb version that uses no caching (and thus adds some overhead).
(Another patch in this patchset adds caching as well.)
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Acked-by: Olaf Kirch <okir@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
This adds functions for encoding and decoding POSIX ACLs for the NFSACL
protocol extension, and the GETACL and SETACL RPCs. The implementation is
compatible with NFSACL in Solaris.
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Acked-by: Olaf Kirch <okir@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
single port
The NFS and NFSACL programs run on the same RPC transport. This patch adds
support for this by converting svc_program into a chained list of programs
(server-side).
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Signed-off-by: Olaf Kirch <okir@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Add the missing NFS3ERR_NOTSUPP error code (defined in NFSv3) to the
system-to-protocol-error table in nfsd. The nfsacl extension uses this error
code.
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Signed-off-by: Olaf Kirch <okir@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
