| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Brijesh Jadav <brijesh.j@ti.com>
Signed-off-by: Hardik Shah <hardik.shah@ti.com>
Signed-off-by: Manjunath Hadli <mrh@ti.com>
Signed-off-by: R Sivaraj <sivaraj@ti.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Karicheri Muralidharan <m-karicheri2@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
These changes are needed for the new TVP514x driver.
Signed-off-by: Brijesh Jadav <brijesh.j@ti.com>
Signed-off-by: Hardik Shah <hardik.shah@ti.com>
Signed-off-by: Manjunath Hadli <mrh@ti.com>
Signed-off-by: R Sivaraj <sivaraj@ti.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Karicheri Muralidharan <m-karicheri2@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Add a driver for the OMAP2 camera block. OMAP2 is used in e.g. Nokia
N800/N810 internet tablet.
This driver uses the V4L2 internal ioctl interface.
Signed-off-by: Sakari Ailus <sakari.ailus@nokia.com>
Signed-off-by: Trilok Soni <soni.trilok@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
configuration
This patch adds a short help for Technisat cards to help the user
selecting the right configuration for his card(s).
Signed-off-by: Uwe Bugla <uwe.bugla@gmx.de>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This commit adds support for the CX24113 DVB-S tuner driver and thus support for the Technisat Skystar2 revision 2.8.
The driver was created with the help of Technisat. Thank you very much.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Bogus controls currently include processing unit auto controls for which no
corresponding manual control is available. Such auto controls make little
sense if any, and are known to crash at least the SiGma Micro webcam.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
frame drop off.
The driver drops incomplete uncompressed video frames to avoid confusing
userspace with corrupt data. Add a nodrop module parameter to turn that
behaviour off and make all frames available to userspace.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
A combined authorship patch from Hans Verkuil and Andy Walls. Raw
VBI can now be captured but requires a video capture to be in progress as well.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This is a port of the fixes Hans Verkuil made for ivtv/cx25840:
The service_set field was used to determine whether raw or sliced VBI was
desired. This is incorrect since it is perfectly valid to select sliced VBI
with a service_set of 0.
Instead the driver should check on VIDIOC_S_FMT whether the type
field matches the raw or sliced VBI type.
Updated the cx18 driver accordingly, including an additional check in
cx18_start_v4l2_encode_stream() that didn't exist in ivtv.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
cx18: Avoid making firmware API calls with the queue lock held. The source
of MPEG strem corruption when not holding the queue lock was found to be that
the MPEG buffer could be retrieved by the user app before it was sync'ed for
the host cpu. Incoming buffers are now sync'ed before being put on q_full and
releasing the queue lock. We can thus avoid the sometimes lengthy call to
the firmware for CPU_DE_SET_MDL while holding the queue lock, so we can get
better performance.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
changes
cx18: Increment version number due to siginificant buffering changes.
Now version 1.0.4
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
allocations
cx18: Add module parameters for finer control over buffer allocations.
User now has the option of setting smaller buffers to get lower
latency transfers from the encoder. User can also now set the number
of buffers used for a stream explicitly.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
cx18: Allow more than 63 capture buffers in rotation per stream. Implement
q_busy to hold buffers the firmware has for use. q_free holds truly unused
buffers in a pool. New buffers are given to the firmware as soon as the
firmware returns one, if there are any to give to the firmware.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Eliminate q_io from stream buffer handling in anticipation of upcoming
changes in buffer handling. q_io was a holdover from ivtv and it's function
in cx18 was trivial and not necessary. We just push things back onto the
front of q_full now, instead of maintaining a 1 buffer q_io queue.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
How to enable the mpeg encoder is not found yet.
The card comes up with gpio 0x0820000 for DVB-T.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
register 0x00 contains 0xa1 for STV0299 and STV0299B
register 0x00 might contain 0x80 when returning from standby
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Acked-by: Sergey Silkin <neovision@rambler.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
In the function cx88_audio_initdev, the value card has been created using
snd_card_new. The other error handling code in this function frees the
value using snd_card_free. I have thus changed the first error case to do
the same. On the other hand, it may be that card is not sufficiently
initialized at this point to use snd_card_free, in which case something
else should be done to free the memory in the error case.
In the function snd_cx88_create the call kfree(chip) in one error case
looks suspicious, both because it is not done in the other error code, and
because chip points into the middle of the memory allocated by
snd_card_new, ie it is not itself associated with a separate kmalloc.
Therefore I have removed it.
The semantic match that finds the first problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S,S1;
position p1,p2,p3;
expression E,E1;
type T,T1;
expression *ptr != NULL;
@@
(
if ((x@p1 = snd_card_new(...)) == NULL) S
|
x@p1 = snd_card_new(...);
)
... when != snd_card_free(...,(T)x,...)
when != if (...) { <+... snd_card_free(...,(T)x,...) ...+> }
when != true x == NULL || ...
when != x = E
when != E = (T)x
when any
(
if (x == NULL || ...) S1
|
if@p2 (...) {
... when != snd_card_free(...,(T1)x,...)
when != if (...) { <+... snd_card_free(...,(T1)x,...) ...+> }
when != x = E1
when != E1 = (T1)x
(
return \(0\|<+...x...+>\|ptr\);
|
return@p3 ...;
)
}
)
@ script:python @
p1 << r.p1;
p3 << r.p3;
@@
print "* file: %s snd_card_new: %s return: %s" % (p1[0].file,p1[0].line,p3[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Add Compro VideoMate E650F (DVB-T part only).
The card based on cx23885 PCI-Express chip, xc3028 tuner and ce6353 demodulator.
Cc: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Added specific entry for WinTV-HVR 850
Signed-off-by: Douglas Schilling Landgraf <dougsland@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Use the new format-negotiation infrastructure, support all four YUV422
packed and the planar formats.
The new translation structure enables to build the format
list with buswidth, depth, host format and camera format
checked, so that it's not done anymore on try_fmt nor
set_fmt.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Allocate and fill a list of formats, supported by this specific
camera-host combination. Use it for format enumeration. Take care to stay
backwards-compatible.
Camera hosts rely on sensor formats available, as well as
host specific translations. We add a structure so that hosts
can define a translation table and use it for format check
and setup.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This pointer will be used by pxa_camera.c to point to its pixel format
data.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
We anyway don't follow the s_fmt_vid_cap / g_fmt_vid_cap / try_fmt_vid_cap
naming, and soc-camera is so far only about video capture, let's simplify
operation names a bit further. set_fmt_cap / try_fmt_cap wasn't a very good
choice too.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Pixel format requested by the user is not necessarily the same, as what
a sensor driver provides. There are situations, when a camera host driver
provides the required format, but requires a different format from the
sensor. Further, the list of formats, supported by sensors is pretty static
and can be pretty good described with a constant list of structures. Whereas
decisions, made by camera host drivers to support requested formats can be
quite complex, therefore it is better to let the host driver do the work.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Minor formatting fixes
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
.try_bus_param() method from struct soc_camera_host_ops is only called at one
location immediately before .try_fmt_cap(), there is no value in keeping these
two methods separate, merge them.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
PCI read error
cx18: cx18_writel_expect() should not declare success on a PCI read error.
This removes the potential for cx18_write*_expect() calls to not
accomplish a PCI write successfully as expected. The CX18-AV core uses the
*expect() calls often and this may be the source of intermittent audio
problems and standands switching problems.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
deferrable work handling
cx18: Change to per CX23418 device work queues for deferrable work handling.
Needed to support 2.6.22 and earlier kernels that can't selectively cancel
work orders. Also will provide slightly better performance on SMP systems.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
tda8290 were using some random video standard for FM. This results on random
errors. Instead, program tda8290 in expert mode, using a configuration near the
one specified on NXP datasheet for tda8295 (available on their site).
Also, properly display that the device is on radio mode.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Probably due to a removed code, tda827x were doing some wrong calculus at the
returned frequency. I suspect that the original idea were to return the
programmed divisor converted into frequency again.
However, the current code is sometimes multiplying the programmed frequency by
62500, and, on other cases, like radio, it dividing it by 1000.
Instead of doing such math, let's just store the frequency value as requested by
the caller module.
Cc: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Cc: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Thanks to Sistema Fenix (http://www.sistemafenix.com.br/) for sponsoring
this
development.
Signed-off-by: Gilberto <gilberto@sistemafenix.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
/home/mauro/v4l-dvb/v4l/tuner-xc2028.c: In function 'xc2028_sleep':
/home/mauro/v4l-dvb/v4l/tuner-xc2028.c:1111: warning: 'return' with no value, in function returning non-void
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
em28xx devices generally get hot when xc3028 tuner is powered on. This
patch solves this by turning power off when the device is not used, at the
expense of having a higher load time, when calling a TV application.
Since firmware load happens on 1 or 2 seconds on most devices, this is not a pain.
Also, it helps to save the planet by saving some power :)
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Since the firmware load is now fast on most boards, better to keep the tuner
off by default. A modprobe parameter were added to keep the old behavior,
to be used by old devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Change log format to look more like URB transactions. In fact, setup and
IN/OUT transactions are merged. This helps to debug the driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Power the LNA while the frontend is in use.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
consequences
cx18: Quiet a sometimes common warning that often has benign consequences.
No one probably cares that the firmware took forever to ack our command, as
they always seem to succeed whether or not the firmware acks it in a reasonable
amount of time.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Update the version number due to significant changes in the way the
mailboxes and interrupts are handled.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Add copyright attribution for files modified by awalls in 2008
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
logging
cx18: Adjust outgoing mailbox timeouts and remove statistics logging.
This saves some wasted storage in struct cx18 for each card. Cutting
the outgoing mailbox timeouts in half from the previous value appears to
be safe with MythTV. Got rid of interrupted case code path after
a wait uninterruptable returns.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
rotation
Restore buffers that have fallen out of the transfer rotation, and check
for coherent mailbox data when processing a stale mailbox.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
handling path
Remove unnecessary MMIO accesses in time critical irq handling path. Also
ensured that the mailbox ack field is read in last, so we know for sure if we
have a stale mailbox or not on receipt.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
strategy
cx18: Streamline cx18-io[ch] wrappers and enforce MMIO retry strategy so that
write retries always occur and read retries never occur (as they never help).
Remove MMIO statistics logging to speed up MMIO accesses. Deprecate & ignore
retry_mmio and mmio_ndelay module parameters, to essentially force
retry_mmio=1 and mmio_ndelay=0.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
work handler
cx18: Propagate staleness of mailbox and mdl ack data to work handler to let
the work handler know that the data from the encoder may not be coherent.
Allows for smarter handling of buffers in future, to deal with MDLs that fall
out of rotation due to irq handler being late in collecting mailbox and mdl ack
info.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Convert the per stream queue spinlocks into mutexes. All queue
manipulation happens via the work queue or system calls into the driver, and
not in an interrupt context. This reduces the amout of time the cx18 driver
keeps interrupts disabled.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
deferable work
Change to singlethreaded global work queue thread for deferable work,
instead of the kernel default multithreaded work queue. This ensures
execution of deferable work is always in the proper order, so caputred buffers
don't get reordered.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
