| Age | Commit message (Collapse) | Author |
|---|
|
Fix wrong bit mask for blanking register. Due to the error a CRT monitor
blanks off due to wrong frequency (out of range) instead of PM signal
(vertical and horizontal frequencies cut off).
Just compare the mask with bits set in the switch(blank) clause below the
changed line.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove fb_save_state() and fb_restore_state operations from frame buffer layer.
They are used only in two drivers:
1. savagefb - and cause bug #11248
2. uvesafb
Usage of these operations is misunderstood in both drivers so kill these
operations, fix the bug #11248 and avoid confusion in the future.
Tested on Savage 3D/MV card and the patch fixes the bug #11248.
The frame buffer layer uses these funtions during switch between graphics
and text mode of the console, but these drivers saves state before
switching of the frame buffer (in the fb_open) and after releasing it (in
the fb_release). This defeats the purpose of these operations.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=11248
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Reported-by: Jochen Hein <jochen@jochen.org>
Tested-by: Jochen Hein <jochen@jochen.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michal Januszewski <spock@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 341ce06f69abfafa31b9468410a13dbd60e2b237 ("page allocator:
calculate the alloc_flags for allocation only once") altered watermark
logic slightly by allowing rt_tasks that are handling an interrupt to set
ALLOC_HARDER. This patch brings the watermark logic more in line with
2.6.30.
This change results in a reduction of the number high-order GFP_ATOMIC
allocation failures reported. See
http://www.gossamer-threads.com/lists/linux/kernel/1144153
[rientjes@google.com: Spotted the problem]
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: Pekka Enberg <penberg@cs.helsinki.fi>
Reviewed-by: Rik van Riel <riel@redhat.com>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: David Rientjes <rientjes@google.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
after direct reclaim failed
If a direct reclaim makes no forward progress, it considers whether it
should go OOM or not. Whether OOM is triggered or not, it may retry the
allocation afterwards. In times past, this would always wake kswapd as
well but currently, kswapd is not woken up after direct reclaim fails.
For order-0 allocations, this makes little difference but if there is a
heavy mix of higher-order allocations that direct reclaim is failing for,
it might mean that kswapd is not rewoken for higher orders as much as it
did previously.
This patch wakes up kswapd when an allocation is being retried after a
direct reclaim failure. It would be expected that kswapd is already
awake, but this has the effect of telling kswapd to reclaim at the higher
order as well.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: Christoph Lameter <cl@linux-foundation.org>
Reviewed-by: Pekka Enberg <penberg@cs.helsinki.fi>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
openipmi list is moderated.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
With the `s' it just won't work.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Names with periods or commas need to be quoted
Use tab not spaces
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Integrate P:/M: lines to single M:
Use tabs not spaces
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Integrate P:/M: to single M:
Use tab for spacing
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Jing Huang <huangj@brocade.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Oops. How did that get there?
(Don't look, it's my original pattern commit...)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This fixes:
ERROR: "log_start_commit" [fs/ext3/ext3.ko] undefined!
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
|
|
To support PCIe hot plug in IOMMU, we register a notifier to respond to device
change action.
When the notifier gets BUS_NOTIFY_UNBOUND_DRIVER, it removes the device
from its DMAR domain.
A hot added device will be added into an IOMMU domain when it first does IOMMU
op. So there is no need to add more code for hot add.
Without the patch, after a hot-remove, a hot-added device on the same
slot will not work.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Tested-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
The model for IOMMU passthrough is that decent devices that can cope
with DMA to all of memory get passthrough; crappy devices with a limited
dma_mask don't -- they get to use the IOMMU anyway.
This is done on the basis that IOMMU passthrough is usually wanted for
performance reasons, and it's only the decent PCI devices that you
really care about performance for, while the crappy 32-bit ones like
your USB controller can just use the IOMMU and you won't really care.
Unfortunately, the check for this was only looking at dev->dma_mask, not
at dev->coherent_dma_mask. And some devices have a 32-bit
coherent_dma_mask even though they have a full 64-bit dma_mask.
Even more unfortunately, fixing that simple oversight would upset
certain broken HP devices. Not only do they have a 32-bit
coherent_dma_mask, but they also have a tendency to do stray DMA to
unmapped addresses. And then they die when they take the DMA fault they
so richly deserve.
So if we do the 'correct' fix, it'll mean that affected users have to
disable IOMMU support completely on "a large percentage of servers from
a major vendor."
Personally, I have little sympathy -- given that this is the _same_
'major vendor' who is shipping machines which claim to have IOMMU
support but have obviously never _once_ booted a VT-d capable OS to do
any form of QA. But strictly speaking, it _would_ be a regression even
though it only ever worked by fluke.
For 2.6.33, we'll come up with a quirk which gives swiotlb support
for this particular device, and other devices with an inadequate
coherent_dma_mask will just get normal IOMMU mapping.
The simplest fix for 2.6.32, though, is just to jump through some hoops
to try to allocate coherent DMA memory for such devices in a place that
they can reach. We'd use dma_generic_alloc_coherent() for this if it
existed on IA64.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Each device has its own 'recovery_offset' showing how far
recovery has progressed on the device.
As the only real significance of this is that fact that it can
be stored in the metadata and recovered at restart, and as
only 1.x metadata can do this, we were only updating
'recovery_offset' to 'curr_resync_completed' when updating
v1.x metadata.
But this is wrong, and we will shortly make limited use of this
field in v0.90 metadata.
So move the update into common code.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Adjust OMAP3 frequency transition latency from 10,000,000uS to a more
reasonable 300,000uS. This causes ondemand and conservative governors to
sample CPU load more often resulting in more responsive behavior.
Tested on Android 2.6.29; using this value and conservative governor, CORE
power consumption on Zoom2 was comparable to the old and unresponsive
10,000,000uS value while UI responsiveness was greatly improved.
Signed-off-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: fix panic when trying to destroy a newly allocated
Btrfs: allow more metadata chunk preallocation
Btrfs: fallback on uncompressed io if compressed io fails
Btrfs: find ideal block group for caching
Btrfs: avoid null deref in unpin_extent_cache()
Btrfs: skip btrfs_release_path in btrfs_update_root and btrfs_del_root
Btrfs: fix some metadata enospc issues
Btrfs: fix how we set max_size for free space clusters
Btrfs: cleanup transaction starting and fix journal_info usage
Btrfs: fix data allocation hint start
|
|
Rafael debugged a resume-time hang (with oopses in workqueue handling)
on his laptop that was due to the 'waker' workqueue entry being
disconnected and then released without the workqueue entry having been
synchronized.
Several people were involved, with Oleg Nesterov doing a debugging patch
showing what workqueue entry was corrupt etc.
This was a regression introduced by commit 7bee549e19 ("Bluetooth: Add
USB autosuspend support to btusb driver") as Rafael points out (not
actually bisected, but it became clear once the bug was found).
Tested-and-reported-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Oliver Neukum <oliver@neukum.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There is a problem where iget5_locked will look for an inode, not find it, and
then subsequently try to allocate it. Another CPU will have raced in and
allocated the inode instead, so when iget5_locked gets the inode spin lock again
and does a search, it finds the new inode. So it goes ahead and calls
destroy_inode on the inode it just allocated. The problem is we don't set
BTRFS_I(inode)->root until the new inode is completely initialized. This patch
makes us set root to NULL when alloc'ing a new inode, so when we get to
btrfs_destroy_inode and we see that root is NULL we can just free up the memory
and continue on. This fixes the panic
http://www.kerneloops.org/submitresult.php?number=812690
Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6:
JBD/JBD2: free j_wbuf if journal init fails.
ext3: Wait for proper transaction commit on fsync
ext3: retry failed direct IO allocations
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - possible read past array alc88[02]_parse_auto_config()
sound: rawmidi: fix MIDI device O_APPEND error handling
sound: rawmidi: fix checking of O_APPEND when opening MIDI device
sound: rawmidi: fix double init when opening MIDI device with O_APPEND
ALSA: hda - Avoid quirk for HP dc5750
ALSA: hda - Tweak OLPC XO-1.5 microphone bias
ALSA: hda: Use model=auto quirk for Sony VAIO VGN-FW170J using ALC262
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
x86/PCI: Adjust GFP mask handling for coherent allocations
PCI ASPM: fix oops on root port removal
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: pasemi_defconfig update
powerpc: 2.6.32 update of defconfigs for embedded 6xx/7xxx, 8xx, 8{3,5,6}xxx
powerpc/8xxx: enable IPsec ESP by default on mpc83xx/mpc85xx
powerpc/83xx: Fix u-boot partion size for MPC8377E-WLAN boards
powerpc/85xx: Fix USB GPIOs for MPC8569E-MDS boards
powerpc/82xx: kmalloc failure ignored in ep8248e_mdio_probe()
powerpc/85xx: sbc8548 - fixup of PCI-e related DTS fields
|
|
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: Use a definition for the userspace cmpxchg emulation syscall
[ARM] Fix test for unimplemented ARM syscalls
ARM: 5784/1: fix early boot machine ID mismatch error display
[ARM] orion5x: update defconfig
[ARM] Kirkwood: update defconfig
[ARM] Kirkwood: clarify PCIe MEM bus/physical address distinction
[ARM] kirkwood: fix PCI I/O port assignment
[ARM] kirkwood: fix section mismatch
[ARM] OpenRD base: Initialize PCI express and i2c
[ARM] properly report mv78100 stepping A1
ARM: 5780/1: KS8695: Fix macro definition bug in regs-switch.c
ARM: 5779/1: ep93xx/micro9.c: fix implicit declaration of function __raw_readl and IOMEM
RealView: Add sparsemem support for the RealView PBX platform
RealView: Remove duplicated #define REALVIEW_SYS_FLAGS* statements
RealView: Add default memory configuration
Check whether the SCU was already initialised
ARMv7: Check whether the SMP/nAMP mode was already enabled
[ARM] pxa: fix resume failure by saving/restoring IPRx registers
[ARM] pxa/palm: fix incorrect initialization of Palm Tungsten C keyboard
[ARM] pxa/zaurus: fix NAND flash OOB layout for Borzoi
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (52 commits)
drm/kms: Init the CRTC info fields for modes forced from the command line.
drm/radeon/r600: CS parser updates
drm/radeon/kms: add debugfs for power management for AtomBIOS devices
drm/radeon/kms: initial mode validation support
drm/radeon/kms/atom/dce3: call transmitter init on mode set
drm/radeon/kms: store detailed connector info
drm/radeon/kms/atom/dce3: fix up usPixelClock calculation for Transmitter tables
drm/radeon/kms/r600: fix rs880 support v2
drm/radeon/kms/r700: fix some typos in chip init
drm/radeon/kms: remove some misleading debugging output
drm/radeon/kms: stop putting VRAM at 0 in MC space on r600s.
drm/radeon/kms: disable D1VGA and D2VGA if enabled
drm/radeon/kms: Don't RMW CP_RB_CNTL
drm/radeon/kms: fix coherency issues on AGP cards.
drm/radeon/kms: fix rc410 suspend/resume.
drm/radeon/kms: add quirk for hp dc5750
drm/radeon/kms/atom: fix potential oops in spread spectrum code
drm/kms: typo fix
drm/radeon/kms/atom: Make card_info per device
drm/radeon/kms/atom: Fix DVO support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
highmem: Fix debug_kmap_atomic() to also handle KM_IRQ_PTE, KM_NMI, and KM_NMI_PTE
highmem: Fix race in debug_kmap_atomic() which could cause warn_count to underflow
rcu: Fix long-grace-period race between forcing and initialization
uids: Prevent tear down race
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
genirq: try_one_irq() must be called with irq disabled
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf tools: Fix permission checks
perf_events: Fix some typo in the perf events config description
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Use root_task_group_empty only with FAIR_GROUP_SCHED
sched: Fix kernel-doc function parameter name
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, amd-ucode: Check UCODE_MAGIC before loading the container file
x86: Fix error return sequence in __ioremap_caller()
x86: Add Phoenix/MSC BIOSes to lowmem corruption list
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: partial revert to fix double brelse WARNING()
ext4: Fix return value of ext4_split_unwritten_extents() to fix direct I/O
ext4: code clean up for dio fallocate handling
ext4: skip conversion of uninit extents after direct IO if there isn't any
ext4: fix ext4_ext_direct_IO()'s return value after converting uninit extents
ext4: discard preallocation when restarting a transaction during truncate
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] SBC-FITPC2 watchdog driver registration fix
|
|
* 'fixes-s3c-2632-rc6' of git://git.fluff.org/bjdooks/linux:
ARM: S3C64XX: DMA: Free node for non-circular queues
ARM: S3C64XX: DMA: Callback with correct buffer pointer
ARM: S3C64XX: DMA: Make src and dst transfer size same
ARM: S3C64XX: DMA: Unify callback functions for success/failure
ARM: S3C64XX: DMA: Protect buffer pointers while manipulation
ARM: S3C64XX: Tidy definition and comments in s3c_dma_has_circular()
ARM: S3C64XX: Remove duplicate s3c_dma_has_circular() definition for S3C64xx.
ARM: SMDK6410: Allocate more GPIO space for WM1190-EV1
ARM: SMDK6410: Configure GPIO pull up for WM835x IRQ line
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (27 commits)
V4L/DVB (13314): saa7134: set ts_force_val for the Hauppauge WinTV HVR-1150
V4L/DVB (13313): saa7134: add support for FORCE_TS_VALID mode for mpeg ts input
V4L/DVB (13311): uvcvideo: Fix compilation warning with 2.6.32 due to type mismatch with abs()
V4L/DVB (13309): uvcvideo: Ignore the FIX_BANDWIDTH for compressed video
V4L/DVB (13287): ce6230 - saa7164-cmd: Fix wrong sizeof
V4L/DVB (13286): pxa-camera: Fix missing sched.h
V4L/DVB (13264): gspca_mr97310a: Change vstart for CIF sensor type 1 cams
V4L/DVB (13257): gspca - m5602-s5k4aa: Add vflip for Fujitsu Amilo Xi 2528
V4L/DVB (13256): gspca - m5602-s5k4aa: Add another MSI GX700 vflip quirk
V4L/DVB (13255): gspca - m5602-s5k4aa: Add vflip quirk for the Bruneinit laptop
V4L/DVB (13240): firedtv: fix regression: tuning fails due to bogus error return
V4L/DVB (13237): firedtv: length field corrupt in ca2host if length>127
V4L/DVB (13230): s2255drv: Don't conditionalize video buffer completion on waiting processes
V4L/DVB (13202): smsusb: add autodetection support for three additional Hauppauge USB IDs
V4L/DVB (13190): em28xx: fix panic that can occur when starting audio streaming
V4L/DVB (13170): bttv: Fix reversed polarity error when switching video standard
V4L/DVB (13169): bttv: Fix potential out-of-order field processing
V4L/DVB (13167): pt1: Fix a compile error on arm
V4L/DVB (13132): fix use-after-free Oops, resulting from a driver-core API change
V4L/DVB (13131): pxa_camera: fix camera pixel format configuration
...
|
|
On an FS where all of the space has not been allocated into chunks yet,
the enospc can return enospc just because the existing metadata chunks
are full.
We get around this by allowing more metadata chunks to be allocated up
to a certain limit, and finding the right limit is a little fuzzy. The
problem is the reservations for delalloc would preallocate way too much
of the FS as metadata. We need to start saying no and just force some
IO to happen.
But we also need to let a reasonable amount of the FS become metadata.
This bumps the hard limit up, later releases will have a better system.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
|
|
Currently compressed IO does not deal with not having its entire extent able to
be allocated. So if we have enough free space to allocate for the extent, but
its not contiguous, it will fail spectacularly. This patch fixes this by
falling back on uncompressed IO which lets us spread the delalloc extent across
multiple extents. I tested this by making us randomly think the reservation had
failed to make it fallback on the uncompressed io way and it seemed to work
fine. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
|
|
This patch changes a few things. Hopefully the comments are helpfull, but
I'll try and be as verbose here.
Problem:
My fedora box was taking 1 minute and 21 seconds to boot with btrfs as root.
Part of this problem was we pick the first block group we can find and start
caching it, even if it may not have enough free space. The other problem is
we only search for cached block groups the first time around, which we won't
find any cached block groups because this is a newly mounted fs, so we end up
caching several block groups during bootup, which with alot of fragmentation
takes around 30-45 seconds to complete, which bogs down the system. So
Solution:
1) Don't cache block groups willy-nilly at first. Instead try and figure out
which block group has the most free, and therefore will take the least amount
of time to cache.
2) Don't be so picky about cached block groups. The other problem is once
we've filled up a cluster, if the block group isn't finished caching the next
time we try and do the allocation we'll completely ignore the cluster and
start searching from the beginning of the space, which makes us cache more
block groups, which slows us down even more. So instead of skipping block
groups that are not finished caching when we have a hint, only skip the block
group if it hasn't started caching yet.
There is one other tweak in here. Before if we allocated a chunk and still
couldn't find new space, we'd end up switching the space info to force another
chunk allocation. This could make us end up with way too many chunks, so keep
track of this particular case.
With this patch and my previous cluster fixes my fedora box now boots in 43
seconds, and according to the bootchart is not held up by our block group
caching at all.
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
|
|
I re-orderred the checks to avoid dereferencing "em" if it was null.
Found by smatch static checker.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
|
|
We don't need to call btrfs_release_path because btrfs_free_path will do
that for us.
Signed-off-by: Li Dongyang <Jerry87905@gmail.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
|
|
We weren't reserving metadata space for rename, rmdir and unlink, which could
cause problems.
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
|
|
This patch fixes a problem where max_size can be set to 0 even though we
filled the cluster properly. We set max_size to 0 if we restart the cluster
window, but if the new start entry is big enough to be our new cluster then we
could return with a max_size set to 0, which will mean the next time we try to
allocate from this cluster it will fail. So set max_extent to the entry's
size. Tested this on my box and now we actually allocate from the cluster
after we fill it. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
|
|
We use journal_info to tell if we're in a nested transaction to make sure we
don't commit the transaction within a nested transaction. We use another
method to see if there are any outstanding ioctl trans handles, so if we're
starting one do not set current->journal_info, since it will screw with other
filesystems. This patch also cleans up the starting stuff so there aren't any
magic numbers.
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
|
|
Sometimes our start allocation hint when we cow a file can be either
EXTENT_HOLE or some other such place holder, which is not optimal. So if we
find that our em->block_start is one of these special values, check to see
where the first block of the inode is stored, and use that as a hint. If that
block is also a special value, just fallback on a hint of 0 and let the
allocator figure out a good place to put the data.
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
|
|
This patch updates defconfig to enable options needed to properly
boot OMAP3 pandora board. It also enables MMC, OTG, GPIO LEDs,
TWL4030 GPIO and sound drivers.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Some drivers have dependencies on this, and therefore should be
enabled.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The host port power is enabled by driving the nEN_USB_PWR low as stated in
the comment. This fix is originally from Steve Sakoman <steve@sakoman.com>.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The original TWL4030 keypad driver from linux-omap used KEY()
macro defined as (col, row), but while it was merged upstream
it was changed to use matrix keypad infrastructure, which uses
(row, col) format. Update the keymap in board file to match
layout of mainline driver.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The patch provides the following fixes:
- keep kernel small enough to boot with standard tools,
- ensure compatibility with both new and legacy distros,
- turn on support for recently added or fixed hardware features.
Created and tested against linux-2.6.32-rc5.
Signed-off-by: Janusz Krzysztofik <jkrzysz@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
With CONFIG_PM=y, the omapfb/lcdc device on Amstrad Delta, after initially
starting correctly, breaks with the following error messages:
omapfb omapfb: resetting (status 0xffffff96,reset count 1)
...
omapfb omapfb: resetting (status 0xffffff96,reset count 100)
omapfb omapfb: too many reset attempts, giving up.
Looking closer at this I have found that it had been broken almost 2 years ago
with commit 2418996e3b100114edb2ae110d5d4acb928909d2, PM fixes for OMAP1.
The definite reason for broken omapfb/lcdc behavoiur in PM mode
appeared to be ARM_IDLECT1:IDLIF_ARM (bit 6) put into idle regardless of LCD
DMA possibly running. The bit were set based on return value of the
omap_dma_running() function that did not check for dedicated LCD DMA
channel status. The patch below fixes this.
Note that the hardcoded register value will be fixed during the next merge
cycle to use OMAP_LCDC_ defines. Currently the OMAP_LCDC_ defines are local
to drivers/video/omap/lcdc.c, so let's not start moving those right now.
Created against linux-2.6.32-rc6
Tested on Amstrad Delta
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
If journal init fails, we need to free j_wbuf.
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: Tao Ma <tao.ma@oracle.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
We cannot rely on buffer dirty bits during fsync because pdflush can come
before fsync is called and clear dirty bits without forcing a transaction
commit. What we do is that we track which transaction has last changed
the inode and which transaction last changed allocation and force it to
disk on fsync.
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
|
