Age | Commit message (Collapse) | Author |
|
At least one report claims that a878539ef994787c447a98c2e3ba0fe3dad984ec
failed to solve lockups, whereas the old limit-to-32-bit trick worked.
Restore the 32-bit limit, but also leave the 255-sector limit in place,
because we know that's needed as well.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-linus:
kbuild: soften modpost checks when doing cross builds
|
|
|
|
A Promise SATA controller will signal hotplug events when a hard
reset (COMRESET) is done on a port. These events aren't masked by
the driver, and the unexpected interrupts will cause a sequence
of failed reset attempts util libata's EH finally gives up.
This has not been a common problem so far, but the pending libata
hardreset-by-default changes makes it a critical issue.
The solution is to disable hotplug events before a reset, and to
reenable them afterwards. (Promise's driver does this too.)
This patch adds SATA-specific versions of ->freeze() and ->thaw()
that also disable and enable hotplug events. PATA ports continue
to use the old versions of ->freeze() and ->thaw().
Accesses to the hotplug register must be serialised via host->lock.
We rely on ap->lock == &ap->host->lock and that libata takes this
lock before ->freeze() and ->thaw(). Document this requirement.
The interrupt handler is adjusted so its hotplug register accesses
are inside the region protected by host->lock.
Tested on various chips (SATA300TX4, SATA300TX2plus, SATAII150TX4,
FastTrack TX4000) with various combinations of SATA and PATA disks,
with and without the pending hardreset-by-default changes.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The printk() logic on when/how to get the console semaphore was
unreadable, this splits the code up into a few helper functions and
makes it easier to follow what is going on.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In case we're accounting from a sub-namespace, the tgids reported will not
refer to the right namespace.
Save the pid_namespace we're accounting in on the acct_glbs and use it in
do_acct_process.
Two less :) places using the task_struct.tgid member.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is minor, but dereferencing even current real_parent is not safe on debug
kernels, since the memory, this points to, can be unmapped - RCU protection is
required.
Besides, the tgid field is deprecated and is to be replaced with task_tgid_xxx
call (the 2nd patch), so RCU will be required anyway.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Revert commit f1a9ee758de7de1e040de849fdef46e6802ea117:
Author: Rik van Riel <riel@redhat.com>
Date: Thu Feb 7 00:14:08 2008 -0800
kswapd should only wait on IO if there is IO
The current kswapd (and try_to_free_pages) code has an oddity where the
code will wait on IO, even if there is no IO in flight. This problem is
notable especially when the system scans through many unfreeable pages,
causing unnecessary stalls in the VM.
Additionally, tasks without __GFP_FS or __GFP_IO in the direct reclaim path
will sleep if a significant number of pages are encountered that should be
written out. This gives kswapd a chance to write out those pages, while
the direct reclaim task sleeps.
Signed-off-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Because of large latencies and interactivity problems reported by Carlos,
here: http://lkml.org/lkml/2008/3/22/211
Cc: Rik van Riel <riel@redhat.com>
Cc: "Carlos R. Mafra" <crmafra2@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Update documentation for the hw_random support to be current:
- Documentation/hw_random.txt has been updated to reflect the
current code: it's a framework now, a "core" with a small
sysfs interface, that hardware-specific drivers plug in to.
Text specific to Intel hardware is now at the end.
- Kconfig now references the Documentation/hw_random.txt file
and better explains what this really does.
Both chunks of documentation now higlight the fact that the kernel entropy
pool is maintained by "rngd", and this driver has nothing directly to do with
that important task.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Older smackfs was parsing MAC rules by characters, thus a need of locking
write sessions on open() was needed. This lock is no longer useful now since
each rule is handled by a single write() call.
This is also a bugfix since seq_open() was not called if an open() O_RDWR flag
was given, leading to a seq_read() without an initialized seq_file, thus an
Oops.
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com>
Reported-by: Jonathan Corbet <corbet@lwn.net>
Acked-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
As Paul pointed out, the ACCESS_ONCE are not needed because we already have
the explicit surrounding memory barriers.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Mike Mason <mmlnx@us.ibm.com>
Cc: Dipankar Sarma <dipankar@in.ibm.com>
Cc: David Smith <dsmith@redhat.com>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Adrian Bunk <adrian.bunk@movial.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add comments requested by Andrew.
Updated comments about synchronize_sched(). Since we use call_rcu and
rcu_barrier now, these comments were out of sync with the code.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Mike Mason <mmlnx@us.ibm.com>
Cc: Dipankar Sarma <dipankar@in.ibm.com>
Cc: David Smith <dsmith@redhat.com>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Adrian Bunk <adrian.bunk@movial.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
With numa enabled, some callers could have a range of memory on one node
but try to free that on other node. This can cause some pages to be
freed wrongly.
For example: when we try to allocate 128g boot ram early for
gart/swiotlb, and free that range later so gart/swiotlb can get some
range afterwards.
With this patch, we don't need to care which node holds the range, just
loop to call free_bootmem_node for all online nodes.
This patch makes free_bootmem_core() more robust by trimming the sidx
and eidx according the ram range that the node has.
And make the free_bootmem_core handle this out of range case. We could
use bdata_list to make sure the range can be freed for sure. So next
time, we don't need to loop online nodes and could use free_bootmem
directly.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Tested-by: Ingo Molnar <mingo@elte.hu>
Cc: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The block2mtd driver (drivers/mtd/devices/block2mtd.c) will kfree an on-stack
pointer when handling an invalid argument line (e.g.
block2mtd=/dev/loop0,xxx).
The kfree was added some time ago when "name" was dynamically allocated.
Signed-off-by: Ingo van Lil <inguin@gmx.de>
Acked-by: Joern Engel <joern@lazybastard.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: <stable@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Provide example for memmap exclude option (it is slightly strange and
non-trivial) and provide nice small HOWTO for people with bad memory.
Signed-off-by: Jan-Simon Moeller <dl9pf@gmx.de>
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The MDIO node in the lite5200b.dts file needs to also claim compatibility
with the older mpc5200 chip. Otherwise the driver won't find the device.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
There's no point in retrying and eventually failing device detection
when the device rejects READ_NATIVE_MAX[_EXT]. Disable HPA unlocking
if READ_NATIVE_MAX[_EXT] is rejected as done when SET_MAX[_EXT] is
rejected.
This allows some old drives to work even if they aren't blacklisted.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This is to fix bugzilla #10254. QSI cdrom attached to pata_sis as
secondary master appears as phantom device for the slave.
Interestingly, instead of not setting DRQ after IDENTIFY which
triggers NODEV_HINT, it aborts both IDENTIFY and IDENTIFY PACKET which
makes EH retry.
Modify EH such that it assumes no device is attached if both flavors
of IDENTIFY are aborted by the device. There really isn't much point
in retrying when the device actively aborts the commands.
While at it, convert NODEV detection message to ata_dev_printk() to
help debugging obscure detection problems.
This problem was reported by Jan Bücken.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Jan Bücken <jb.faq@gmx.de>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
pata_it821x needs to look at raw request size in check_atapi_dma().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Implement ata_qc_raw_nbytes() which determines the raw user-requested
size of a PC command.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Remove all irqs_disabled() sanity checks, as they are not safe on
a RT-enabled kernel and will trigger bogus warnings.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This fixes a DMA mapping leakage in the case where we reject a DMA
buffer because of its address.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Christian Casteyde <casteyde.christian@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The iwlxxxx_pci_remove functions are not needed when drivers are not
compiled as modules - they can thus be discarded at kernel link time.
This is already captured by having them as __devexit_p in the pci_driver
struct - these are supposed to be pointers to __devexit functions, but was not.
This is now fixed.
This problem was reported by Toralf Forster when testing the compilation of
2.6.25-rc6.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: Toralf Forster <toralf.foerster@gmx.de>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
drivers/net/wireless/arlan-proc.c:1216: warning: 'arlan_root_table' defined but not used
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch fixes a synchronization problem on the 4965 and 3945 with the
mac start callback routine. The problem is that this function exits BEFORE the
'xxx_alive_start' has completed. This can lead to a problem if a
subsequent MAC callback attempts to issue a firmware command.
Signed-off-by: Rick Farrington <rickdic@hotmail.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Even when all fields are unsigned char, struct still might have
alignment > 1. Does so on arm, unless you explicitly say that
it's packed...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This adds the id for Corega CG-WLUSB2GPX.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Pascal Terjan <pterjan@mandriva.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Kazunori MIYAZAWA <kazunori@miyazawa.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Proxy neighbors do not have any reference counting, so any caller
of pneigh_lookup (unless it's a netlink triggered add/del routine)
should _not_ perform any actions on the found proxy entry.
There's one exception from this rule - the ipv6's ndisc_recv_ns()
uses found entry to check the flags for NTF_ROUTER.
This creates a race between the ndisc and pneigh_delete - after
the pneigh is returned to the caller, the nd_tbl.lock is dropped
and the deleting procedure may proceed.
One of the fixes would be to add a reference counting, but this
problem exists for ndisc only. Besides such a patch would be too
big for -rc4.
So I propose to introduce a __pneigh_lookup() which is supposed
to be called with the lock held and use it in ndisc code to check
the flags on alive pneigh entry.
Changes from v2:
As David noticed, Exported the __pneigh_lookup() to ipv6 module.
The checkpatch generates a warning on it, since the EXPORT_SYMBOL
does not follow the symbol itself, but in this file all the
exports come at the end, so I decided no to break this harmony.
Changes from v1:
Fixed comments from YOSHIFUJI - indentation of prototype in header
and the pndisc_check_router() name - and a compilation fix, pointed
by Daniel - the is_routed was (falsely) considered as uninitialized
by gcc.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Fix Oops with TQM5200 on TQM5200
[POWERPC] mpc5200: Fix null dereference if bestcomm fails to initialize
[POWERPC] mpc5200-fec: Fix possible NULL dereference in mdio driver
[POWERPC] Fix crash in init_ipic_sysfs on efika
[POWERPC] Don't use 64k pages for ioremap on pSeries
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: exec PT_DTRACE
[SPARC64]: Use shorter list_splice_init() for brevity.
[SPARC64]: Remove most limitations to kernel image size.
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
sch_htb: fix "too many events" situation
connector: convert to single-threaded workqueue
[ATM]: When proc_create() fails, do some error handling work and return -ENOMEM.
[SUNGEM]: Fix NAPI assertion failure.
BNX2X: prevent ethtool from setting port type
[9P] net/9p/trans_fd.c: remove unused variable
[IPV6] net/ipv6/ndisc.c: remove unused variable
[IPV4] fib_trie: fix warning from rcu_assign_poinger
[TCP]: Let skbs grow over a page on fast peers
[DLCI]: Fix tiny race between module unload and sock_ioctl.
[SCTP]: Fix build warnings with IPV6 disabled.
[IPV4]: Fix null dereference in ip_defrag
|
|
The iWARP protocol limits RDMA read requests to a single scatter
entry. NFS/RDMA has code in rdma_read_max_sge() that is supposed to
limit the sge_count for RDMA read requests to 1, but the code to do
that is inside an #ifdef RDMA_TRANSPORT_IWARP block. In the mainline
kernel at least, RDMA_TRANSPORT_IWARP is an enum and not a
preprocessor #define, so the #ifdef'ed code is never compiled.
In my test of a kernel build with -j8 on an NFS/RDMA mount, this
problem eventually leads to trouble starting with:
svcrdma: Error posting send = -22
svcrdma : RDMA_READ error = -22
and things go downhill from there.
The trivial fix is to delete the #ifdef guard. The check seems to be
a remnant of when the NFS/RDMA code was not merged and needed to
compile against multiple kernel versions, although I don't think it
ever worked as intended. In any case now that the code is upstream
there's no need to test whether the RDMA_TRANSPORT_IWARP constant is
defined or not.
Without this patch, my kernel build on an NFS/RDMA mount using NetEffect
adapters quickly and 100% reproducibly failed with an error like:
ld: final link failed: Software caused connection abort
With the patch applied I was able to complete a kernel build on the
same setup.
(Tom Tucker says this is "actually an _ancient_ remnant when it had to
compile against iWARP vs. non-iWARP enabled OFA trees.")
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Tom Tucker <tom@opengridcomputing.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
It appears that 64-bit PCI resources cannot possibly ever have worked on
x86-32 even when the RESOURCES_64BIT config option was set, because any
driver that tried to [pci_]ioremap() the resource would have been unable
to do so because the high 32 bits would have been silently dropped on
the floor by the ioremap() routines that only used "unsigned long".
Change them to use "resource_size_t" instead, which properly encodes the
whole 64-bit resource data if RESOURCES_64BIT is enabled.
Acked-by: H. Peter Anvin <hpa@kernel.org>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The printk() can deadlock because it can wake up klogd(), and
task enqueueing will try to read the time in order to set a hrtimer.
Reported-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Debugged-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The "bestcomm-core" driver defines its of_match table as follows
static struct of_device_id mpc52xx_bcom_of_match[] = {
{ .type = "dma-controller", .compatible = "fsl,mpc5200-bestcomm", },
{ .type = "dma-controller", .compatible = "mpc5200-bestcomm", },
{},
};
so while registering the driver, the driver's probe function won't be
called, because the device tree node doesn't have a device_type
property. Thus the driver's bcom_engine structure won't be allocated.
Referencing this structure later causes observed Oops.
Checking bcom_eng pointer for NULL before referencing data pointed
by it prevents oopsing, but fec driver still doesn't work (because
of the lost bestcomm match and resulted task allocation failure).
Actually the compatible property exists and should match and so
the fec driver should work.
This removes .type = "dma-controller" from the bestcomm driver's
mpc52xx_bcom_of_match table to solve the problem.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
If the bestcomm initialization fails, calls to the task allocate
function should fail gracefully instead of oopsing with a NULL deref.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
If the reg property is missing from the phy node (unlikely, but possible),
then the kernel will oops with a NULL pointer dereference. This fixes
it by checking the pointer first.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The global primary_ipic in arch/powerpc/sysdev/ipic.c can remain NULL
if ipic_init() fails, which will happen on machines that don't have an
ipic interrupt controller. init_ipic_sysfs() will crash in that case.
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
On pSeries, the hypervisor doesn't let us map in the eHEA ethernet
adapter using 64k pages, and thus the ehea driver will fail if 64k
pages are configured. This works around the problem by always
using 4k pages for ioremap on pSeries (but not on other platforms).
A better fix would be to check whether the partition could ever
have an eHEA adapter, and only force 4k pages if it could, but this
will do for 2.6.25.
This is based on an earlier patch by Tony Breeds.
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The PT_DTRACE flag is meaningless and obsolete.
Don't touch it.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
HTB is event driven algorithm and part of its work is to apply
scheduled events at proper times. It tried to defend itself from
livelock by processing only limited number of events per dequeue.
Because of faster computers some users already hit this hardcoded
limit.
This patch limits processing up to 2 jiffies (why not 1 jiffie ?
because it might stop prematurely when only fraction of jiffie
remains).
Signed-off-by: Martin Devera <devik@cdi.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
From: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
We don't need one cqueue thread for each CPU. cqueue is used for
receiving userspace datagrams, which are very rare and thus will
happily live with a single queue.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The module alias support in the kernel have a consistency
check where it is checked that the size of a structure
in the kernel and on the build host are the same.
For cross builds this check does not make sense so detect
when we do cross builds and silently skip the check in these
situations.
This fixes a build bug for a wireless driver when cross building
for arm.
Acked-by: Michael Buesch <mb@bu3sch.de>
Tested-by: Gordon Farquharson <gordonfarquharson@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: stable@kernel.org
|
|
Sometimes kernel-doc and xmlto conspire to create output that is invalid
and causes problems. Until I know a real/better solution, change the
source code that causes this.
If anyone has better fixes or can just explain what is happening here,
that would be great.
xmlto: input does not validate (status 1)
mmotm-2008-0314-1449/Documentation/DocBook/kernel-api.xml:71468: parser error : Opening and ending tag mismatch: programlisting line 71464 and para
</para><para>
^
mmotm-2008-0314-1449/Documentation/DocBook/kernel-api.xml:71480: parser error : Opening and ending tag mismatch: para line 71473 and programlisting
</programlisting></informalexample>
^
make[1]: *** [Documentation/DocBook/kernel-api.html] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|