| Age | Commit message (Collapse) | Author |
|---|
|
lost.
On particularly weak signals, changing register 0xab after setting the
interleave mode will cause the FEC lock to get lost (while still holding the
EQ lock). So remove the write entirely, which seems to have had no adverse
effect in either of my ClearQAM environments (and in particular resolves the
customer's reported issue).
Also flip around the order of the amhum optimization and the interleave setup
to be consistent with the windows driver, which has the side-benefit of doing
them both in the same call (since the amhum optimization can only be done once
the interleave setup).
This work was sponsored by ONELAN Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The HVR-1600 doesn't use the standard mechanism for computing the gain when
in QAM mode, instead always forcing it to be 0x02. Provide the ability to
override the algorithm on a per-board basis.
This change results in an improvement of 0.4-0.6 dB for QAM tuning.
This work was sponsored by ONELAN Limited.
Cc: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The sh51409 driver was only doing the QAM optimization a single time, and it
would only occur if you received a lock instantaneously after the tuning
request. Restructure the code so that the optimization occurs once you reach
a signal lock.
Note that this depends on the caller polling for status, but we don't have
much choice at this point without an independent thread monitoring the lock
status. Also, at this point pretty much every application polls for status
lock after doing the tune, so the likelihood of the optimization not occurring
in the real world is pretty low.
The state machine has also been reworked such that setting the interleave mode
is now a dependency of doing the QAM optimization. Before both were mutually
exclusive, which was not consistent with the Windows driver. We now have a
single state machine that controls both.
The changes as-is are only enabled for the HVR-1600. Once the changes are
tested with some of the other boards, this change should be made generic and
the "_legacy" functions should be removed.
This work was sponsored by ONELAN Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Perform some optimization of the register configuration based on a trace
of the HVR-1600 Windows i2c traffic (and consultation with Steven Toth).
Note that some of these values may be able to be moved into the common driver,
but I am holding off on that until they can be tested with other boards.
This work was sponsored by ONELAN Limited.
Cc: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
It seems that some patch broke alt modprobe parameter. Fix it to allow
changing alternate interfaces during module load and at runtime.
If changed during runtime, you'll need to stop a and restart stream for
the parameter to be used.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The reg_w_seq() function expects the sequence length in entries
and not in bytes. One entry in init_7302 and init_7311 is two
bytes and not one.
Signed-off-by: Marton Nemeth <nm127@freemail.hu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
usb_control_msg().
The function usb_control_msg() can return error any time so at least
warn the user if an error happens. No message is printed in case of
normal operation.
Signed-off-by: Marton Nemeth <nm127@freemail.hu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
and pb0330.
- the pb03303x exchanges were the mi0360soc ones
- add the new sensor mi0360soc
- the new exchanges are taken from the info file of the ms-win driver
of the webcams 0ac8:301b and 0ac8:303b (vm30x.inf)
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
-EINVAL is required by the V4L2 specification. -ENODEV is simply wrong
as the device exists.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The MSI StarCam 370i (1b3b:2951) requires the MINMAX quirk. Add a
corresponding entry in the device IDs list.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
sensors.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
bridge.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
- the sensors are now initialized sooner
- om6802:
. set some parameters in factory mode
. lack of some parameters
. gpio adjustments
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
- sensor address is 0x34
- sensor i2c is 100 kHz
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
All PAC7311 specific functions remain in pac7311.c. All PAC7302 specific
functions are moved to pac7302.c. The USB device table is also divided into
two parts. This makes it possible to remove the sensor specific decisions
from different functions and also remove sensor infromation from the USB
device table.
The common functions are just copied to both subdrivers. These common
functions can be separated later to a common file or helper module.
Signed-off-by: Marton Nemeth <nm127@freemail.hu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Creating the start of the frame is done in the same way for pac7302
and for pac7311. Extract this common part to the pac_start_frame()
function.
Signed-off-by: Marton Nemeth <nm127@freemail.hu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Remove struct sd dependency from pac_find_sof() function implementation.
This step prepares separation of pac7302 and pac7311 specific parts of
struct sd.
Signed-off-by: Marton Nemeth <nm127@freemail.hu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
control support
Patch for EvolutePC TvWay+ USB ISDB-Tb remote control support.
[dougsland@redhat.com: fixed malformed patch]
Cc: Patrick Boettcher <pboettcher@dibcom.fr>
Signed-off-by: Sergio C Fortier <sergiofortier@yahoo.com.br>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
load smsdvb also for the hauppauge tiger cards
[dougsland@redhat.com: fixed rejects due changes in sms-cards.c]
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Acked-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This patch removes some fe->ops.X() functions which do nothing more useful than the default.
Signed-off-by: Akihiro Tsukada <tskd2@yahoo.co.jp>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This patch makes the driver return the correct DTV_DELIVERY_SYSTEM.
The driver previously returned SYS_UNDEFINED for DTV_DELIVERY_SYSTEM property,
as it lacked any driver specific S2API support.
Signed-off-by: Akihiro Tsukada <tskd2@yahoo.co.jp>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
i2c_smbus_read_byte_data() returns a negative value on error. It is very
likely to be != -1 (-EPERM).
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Convert printks to em28xx_err and em28xx_info
Signed-off-by: Filipe Rosset <rosset.filipe@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Convert printks to em28xx_err.
Signed-off-by: Filipe Rosset <rosset.filipe@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Trivial patch which adds the __init/__exit macros to the module_init/
module_exit functions of the following drivers in media video:
drivers/media/video/ivtv/ivtv-driver.c
drivers/media/video/cx18/cx18-driver.c
drivers/media/video/davinci/dm355_ccdc.c
drivers/media/video/davinci/dm644x_ccdc.c
drivers/media/video/saa7164/saa7164-core.c
drivers/media/video/saa7134/saa7134-core.c
drivers/media/video/cx23885/cx23885-core.c
Cc: Hermann Pitton <hermann-pitton@arcor.de>
Acked-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Acked-by: Andy Walls <awalls@radix.net>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
If vpfe_dev->std_index equals ARRAY_SIZE(vpfe_standards), that is
one too large.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
second
[mchehab@redhat.com: add asm/div64.h and allocate vars only if dvb_demux_speedcheck specified]
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
downward
gspca_mr97310a: Change brightness for VGA type 1 cameras downward
Signed-off-by: Theodore Kilgore <kilgota@banach.math.auburn.edu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
gspca_mr97310a: Fix / update some comments
Signed-off-by: Theodore Kilgore <kilgota@banach.math.auburn.edu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Digital VGA camera
gspca_mr97310a: Partly back off red gain change for Sakar Digital VGA camera
Signed-off-by: Theodore Kilgore <kilgota@banach.math.auburn.edu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
taking effect
In the changeset entitled, "tda18271: add support for the set_config method",
the initialization order was changed such that the standard map overrides
were being applied before loading the default standard map, based on the
stepping of the silicon. This changeset restores the proper order by
processing the standard map overrides both within the tda18271_set_config()
and the tda18271_attach() functions, after we read the id register of the
tuner.
Thanks to Michael Obst for his testing, helping me to identify the regression.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Michael Obst <mike.obst@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
control
Signed-off-by: Michael Obst <mike.obst@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
As pointed out by Hermann Pitton, it turns out that the DTV1000S card's
analog entry made it into the #if 0 flyvideo tweaks in saa7134-cards.c
and is not valid there.
This patch fixes the problem.
Cc: hermann pitton <hermann-pitton@arcor.de>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Add whitespace around binary operators in cx23888-ir.c
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This patch fixes the kernel bug 14195 (random errors - bad images -
with the webcam 10fd:8050 - sensor tas5130cxx).
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Setting the tuner frequency at the same time as initializing the other devices
on the i2c bus can cause problems on devices that require firmware download or
extensive calibration proceduces during initialization.
This change allows us to prevent the tune at startup for devices that perform
better without it.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
VGA camera
gspca_mr97310a: Change blue gain setting for Sakar Digital VGA camera
Signed-off-by: Theodore Kilgore <kilgota@banach.math.auburn.edu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
gspca_mr97310a: Fix / update some comments
Signed-off-by: Theodore Kilgore <kilgota@banach.math.auburn.edu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
gscpa_mr97310a: Add Trust Spyc@m 100 USB ID
Signed-off-by: Aurelien Jacobs <aurel@gnuage.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
When "shooting" certain (quite rare) scenes, the mr97310's compression is not
effective and it cannot keep up with the data stream. This patch adds a
minimum clock divider control, which influences the maximum framerate,
libv4l will automatically increase this minimum clockdiv control when it
detect the cam cannot keep up.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The variables are unsigned so the test `>= 0' is always true,
the `< 0' test always fails. In these cases the other part of
the test catches wrapped values.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
In buffer_release() the previously allocated pagetables are not
freed, which might result in a memory leak in certain application
use-cases, where the frame format is changed from planar format to
non-planar format. The fix explicitely frees the page tables when a
format change is done and when buffer_release() is called.
Signed-off-by: Johann Friedrichs <johann.friedrichs@web.de>
Signed-off-by: Michael Hunold <hunold@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Upcoming I2C v4l2_subdev drivers need a way to control the subdevice
power state from the core. This use case is already partially covered by
the tuner s_standby operation, but no way to explicitly come back from
the standby state is available.
Rename the tuner s_standby operation to core s_power, and fix tuner
drivers accordingly. The tuner core will call s_power(0) instead of
s_standby(). No explicit call to s_power(1) is required for tuners as
they are supposed to wake up from standby automatically.
[mchehab@redhat.com: CodingStyle fix]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
