| Age | Commit message (Collapse) | Author |
|---|
|
Hi,
This patch contains some of the bug fixes done for S2io driver.
Following are the brief description of changes
1. Continuing with initialization if we get minimum required MSI-X vectors
2. fix for ethtool online link test fails
3. make wait_for_cmd_complete generic for all command status registers
4. Print "Device is on PCI-E bus" for Xframe-E card
5. CX4 requires additional delay after sw_reset, and requires higher value for igp
6. Fixed panic due to non-TCP and/or LLC/SNAP traffic in case of lro
7. remove legacy code for old transponder
8. SPECIAL_REG_WRITE made to use 32-bit writes irrespective of system type
9. handle link interrupt as per user guide for Xframe II
10. Wait till all interrupts hndled
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
hi,
This patch contains the modification and bug fixes with respect to
input parameters and outupt dmesages. following is brief description
of the changes.
1. Set default values for rx_ring_sz[0..7] and tx_fifo_len[0..7]
2. verify few basic load parameters
3. read product description from VPD
4. clean up of dmesg when driver is loaded
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
hi,
This patch contains all the changes that were done to improve
performance of s2io driver. one line description of the changes
are
1. For Non NAPI case the rx interrupt handler is being called
unconditionally
2. code optimization and adding prefetch skb->data
3. Remove modulo operations in fast path
4. Enable Group Reads and set backoff interval to 0x1000
5. correct PIC_CNTL_SHARED_SPLITS macro definition, and reduce
pause parameter
6. Corrected logic of identifying rx buffer level in rx_buffer_level()
7. fix DMA map and unmap done with different sizes in 1-buf mode
8. Removed forcible disabling of ERO
9. Send up the packets with transfer code = 0x5
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
|
|
Apply the same rules as the anon pipe pages, only allow stealing
if no one else is using the page.
Signed-off-by: Jens Axboe <axboe@suse.de>
|
|
Currently we rely on the PIPE_BUF_FLAG_LRU flag being set correctly
to know whether we need to fiddle with page LRU state after stealing it,
however for some origins we just don't know if the page is on the LRU
list or not.
So remove PIPE_BUF_FLAG_LRU and do this check/add manually in pipe_to_file()
instead.
Signed-off-by: Jens Axboe <axboe@suse.de>
|
|
We need to use the minium of {len, PAGE_SIZE-off}, not {len, PAGE_SIZE}-off.
The latter doesn't make any sense, and could cause us to attempt negative
length transfers...
Signed-off-by: Jens Axboe <axboe@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit-current
* 'audit.b10' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit-current:
[PATCH] Audit Filter Performance
[PATCH] Rework of IPC auditing
[PATCH] More user space subject labels
[PATCH] Reworked patch for labels on user space messages
[PATCH] change lspp ipc auditing
[PATCH] audit inode patch
[PATCH] support for context based audit filtering, part 2
[PATCH] support for context based audit filtering
[PATCH] no need to wank with task_lock() and pinning task down in audit_syscall_exit()
[PATCH] drop task argument of audit_syscall_{entry,exit}
[PATCH] drop gfp_mask in audit_log_exit()
[PATCH] move call of audit_free() into do_exit()
[PATCH] sockaddr patch
[PATCH] deal with deadlocks in audit_free()
|
|
When iptables userspace adds an ipt_standard_target, it calculates the size
of the entire entry as:
sizeof(struct ipt_entry) + XT_ALIGN(sizeof(struct ipt_standard_target))
ipt_standard_target looks like this:
struct xt_standard_target
{
struct xt_entry_target target;
int verdict;
};
xt_entry_target contains a pointer, so when compiled for 64 bit the
structure gets an extra 4 byte of padding at the end. On 32 bit
architectures where iptables aligns to 8 byte it will also have 4
byte padding at the end because it is only 36 bytes large.
The compat_ipt_standard_fn in the kernel adjusts the offsets by
sizeof(struct ipt_standard_target) - sizeof(struct compat_ipt_standard_target),
which will always result in 4, even if the structure from userspace
was already padded to a multiple of 8. On x86 this works out by
accident because userspace only aligns to 4, on all other
architectures this is broken and causes incorrect adjustments to
the size and following offsets.
Thanks to Linus for lots of debugging help and testing.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
* 'splice' of git://brick.kernel.dk/data/git/linux-2.6-block:
[PATCH] vmsplice: allow user to pass in gift pages
[PATCH] pipe: enable atomic copying of pipe data to/from user space
[PATCH] splice: call handle_ra_miss() on failure to lookup page
[PATCH] Add ->splice_read/splice_write to def_blk_fops
[PATCH] pipe: introduce ->pin() buffer operation
[PATCH] splice: fix bugs in pipe_to_file()
[PATCH] splice: fix bugs with stealing regular pipe pages
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/ipath: tidy up white space in a few files
IB/ipath: fix label name in interrupt handler
IB/ipath: improve sparse annotation
IB/ipath: simplify IB timer usage
IB/ipath: simplify RC send posting
IB/ipath: prevent hardware from being accessed during reset
IB/ipath: fix verbs registration
IB/ipath: change handling of PIO buffers
IB/ipath: iterate over correct number of ports during reset
IB/ipath: set up 32-bit DMA mask if 64-bit setup fails
IB/ipath: fix race with exposing reset file
IB/mthca: Fix offset in query_gid method
|
|
At suspend time, the TSC CPUFREQ_SUSPENDCHANGE notifier change might
wrongly enable interrupt. cpufreq driver suspend/resume is in interrupt
disabled environment.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The PC Speaker driver's ->probe() routine doesn't even get called in the
64-bit kernels. The reason for that is that the arch code apparently has
to explictly add a "pcspkr" platform device in order for the driver core to
call the ->probe() routine. arch/i386/kernel/setup.c unconditionally adds
a "pcspkr" device, but the x86_64 kernel has no code at all related to the
PC Speaker.
The patch below copies the relevant code from i386 to x86_64, which makes
the PC Speaker work for me on x86_64.
Cc: Dmitry Torokhov <dtor_core@ameritech.net>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Fix genrtc's read() routine for 64-bit platforms. Current gen_rtc_read()
stores 64bit integer and returns 8 even if an user tried to read a 32bit
integer.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Make rtc-dev work well on 64-bit platforms with 32-bit userland. On those
platforms, users might try to read 32-bit integer value. This patch make
rtc-dev's read() work well for both "int" and "long" size. This tweak is came
from genrtc driver.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Consider return value of __put_user() when setting up a signal frame
instead of ignoring it.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
As pointed out by Paulo Marques <pmarques@grupopie.com> MAX_IPD_TIME is by
a factor of ten too small. Since this means that we allow ten times more
IPDs in the intended time frame this could result in a cpu check stop of a
physical cpu.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Add an nid member to the spu structure, and store the numa id of the spu there
on creation.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Change of_node_to_nid() to traverse the device tree, looking for a numa id.
Cell uses this to assign ids to SPUs, which are children of the CPU node.
Existing users of of_node_to_nid() are altered to use of_node_to_nid_single(),
which doesn't do the traversal.
Export an attach_sysdev_to_node() function, allowing system devices (eg.
SPUs) to link themselves into the numa topology in sysfs.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Based on an older patch from Mike Kravetz <kravetz@us.ibm.com>
We need to have a mem_map for high addresses in order to make fops->no_page
work on spufs mem and register files. So far, we have used the
memory_present() function during early bootup, but that did not work when
CONFIG_NUMA was enabled.
We now use the __add_pages() function to add the mem_map when loading the
spufs module, which is a lot nicer.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch fixes two bugs with the way sparsemem interacts with memory add.
They are:
- memory leak if memmap for section already exists
- calling alloc_bootmem_node() after boot
These bugs were discovered and a first cut at the fixes were provided by
Arnd Bergmann <arnd@arndb.de> and Joel Schopp <jschopp@us.ibm.com>.
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Joel Schopp <jschopp@austin.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Currently loading the ioc3 as a module will cause the ports to be numbered
in reverse order. This mod maintains the proper order of cards for port
numbering.
Signed-off-by: Patrick Gefre <pfg@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Currently we check PageDirty() in order to make the decision to swap out
the page. However, the dirty information may be only be contained in the
ptes pointing to the page. We need to first unmap the ptes before checking
for PageDirty(). If unmap is successful then the page count of the page
will also be decreased so that pageout() works properly.
This is a fix necessary for 2.6.17. Without this fix we may migrate dirty
pages for filesystems without migration functions. Filesystems may keep
pointers to dirty pages. Migration of dirty pages can result in the
filesystem keeping pointers to freed pages.
Unmapping is currently not be separated out from removing all the
references to a page and moving the mapping. Therefore try_to_unmap will
be called again in migrate_page() if the writeout is successful. However,
it wont do anything since the ptes are already removed.
The coming updates to the page migration code will restructure the code
so that this is no longer necessary.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Blaisorblade's uml-makefile-nicer makes a V=0 build say SYMLINK where
what's happening is really a LINK.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Acked-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
GCC hardened introduces additional symbol refererences (for the canary and
friends), also in modules - add weak export_symbols for them. We already
tested that the weak declaration creates no problem on both GCC's providing
the function definition and on GCC's which don't provide it.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
*) Rather than duplicate in various buggy ways the application of
CFLAGS_NO_HARDENING and UNPROFILE (which apply to the same files),
centralize it in Makefile.rules. UNPROFILE_OBJS mustn't be listed in
USER_OBJS but are compiled as such.
I've also verified that unprofile didn't work in the current form, because we
set _c_flags directly (using CFLAGS and not USER_CFLAGS, which is wrong),
which is normally used by c_flags, but we also override c_flags for all
USER_OBJS, and there we don't call unprofile.
Instead it only worked for unmap.o, the only one which wasn't a USER_OBJ.
We need to set c_flags (which is not a public Kbuild API) to clear a lot of
compilation flags like -nostdinc which Kbuild forces on everything.
*) Rather than $(CFLAGS_$(notdir $@)), which expands to CFLAGS_anObj.s when
building "anObj.s", use $(CFLAGS_$(*F).o) which always accesses
CFLAGS_anObj.o, like done by Kbuild.
*) Make c_flags apply to all targets having the same basename, rather than
listing .s, .i, .lst and .o, with the use (which I tested) of
$(USER_OBJS:.o=.%): c_flags = ...
and of
- $(obj)/unmap.c: _c_flags = ...
+ $(obj)/unmap.%: _c_flags = ...
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
To make some half-assembly stubs compile, disable various "hardened" GCC
features:
*) we can't make it build PIC code as we need %ebx to do syscalls and GCC
wants it free for PIC
*) we can't leave stack protection as the stub is moved (not relocated!) in
memory so the RIP-relative access to the canary tries reading from an
unmapped address and causes a segfault, since we move the stub of various
megabytes (the exact amount will be decided at runtime) away from the
link-time address.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Move the build of user-offsets to arch/um/sys-$(SUBARCH), where it's located.
So we can also build it via Kbuild with its dependency tracking rather than by
hand. While hacking here, fix also a lot of little cosmetic things.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Append /usr/lib/uml to the existing PATH environment variable to let execvp()
search uml_net in FHS compliant locations.
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
I sent a patch, it was applied as cda402b283c34a24b091f78eee116963e9494762,
then it was applied again as 181ae4005d0a4010802be534d929b38c42b9ac06 by
mistake. But while the 1st time it modified (correctly) cow_header_v3, the
2nd it modified cow_header_v3_broken.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Blairsorblade noticed some confusion between our use of a system
call's return value and errno. This patch fixes a number of related
bugs -
using errno instead of a return value
using a return value instead of errno
forgetting to negate a error return to get a positive error code
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Bring defconfig up to date.
Also disable CONFIG_BLK_DEV_UBD_SYNC by default. By performing synchronous
I/O to the host, it slows things down, only protects against host crashes, and
can make a UML appear to hang while it waits for the host's disk.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The MADVISE_REMOVE-checking code didn't clean up after itself.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Remove redundant NULL checks before [kv]free + small CodingStyle cleanup for
arch/
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
A quick hack to allow skas0 mode to run on 2G/2G hosts.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
We need to walk the region list properly.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Suppress the initcall-return-value warnings unless initcall_debug was
specified.
They do find bugs, but they're extremely small ones and as Andi points out,
people get distressed.
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The apic= option can be used to set the APIC driver too. When that is done
this code would always produce bogus warnings.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The 32bit version of e820_all_mapped() needs to use u64 to avoid overflows on
PAE systems. Pointed out by Jan Beulich
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The patch I submitted earlier to fix disabled LAPIC handling in ACPI was
mismerged for some reason I still don't quite understand. Parts of it was
applied to the wrong function.
This patch fixes it up.
Cc: <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
When retrying a failed BIO_RW_BARRIER request, we need to keep the reference
in ->nr_pending over the whole retry. Currently, we only hold the reference
if the failed request is the *last* one to finish - which is silly, because it
would normally be the first to finish.
So move the rdev_dec_pending call up into the didn't-fail branch. As the rdev
isn't used in the later code, calling rdev_dec_pending earlier doesn't hurt.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Move the test for 'do barrier work' down a bit so that if the first write to a
raid1 is a BIO_RW_BARRIER write, the checking done by superblock writes will
cause the right thing to happen.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Because that is what you get if a BIO_RW_BARRIER isn't supported!
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
in raid10
We need to hold a reference to rdevs while reading and writing to attempt to
correct read errors. This reference must be taken under an rcu lock.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
We should add to the counter for the rdev *after* checking if the rdev is
NULL!!!
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Bastian Blank <bastian@waldi.eu.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Jeff Garzik <jeff@garzik.org>
Acked-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Names that are the opposite of their intended meanings are not so helpful.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
