| Age | Commit message (Collapse) | Author |
|---|
|
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Print banner message once per controller in m68k host drivers.
* Change printk() level to KERN_INFO in buddha, falconide and gayle.
* Add banner message to q40ide.
This is basically a preparation for the future IDE layer changes.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Move setting hwif->sg_max_nents from pmac_ide_setup_device()
to pmac_ide_setup_dma().
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Move setting hwif->gendev.parent from ide_pci_setup_ports()
to ide_hwif_configure().
* Always set hwif->io_ports in ide_hwif_configure().
* Use ide_init_port_hw() in ide_hwif_configure().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* ide_init_hwif_ports() call in setup-pci.c::ide_hwif_configure()
doesn't depend on the default cotrol register offset, default IRQ
or ppc_ide_md.ide_init_hwif implementations so ide_std_init_ports()
can always be used.
* Since 'base' is always non-zero and thus hwif->io_ports[IDE_DATA_OFFSET]
is also non-zero always clear hwif->noprobe.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* hwif->hold is always set in au_ide_probe() (few lines earlier),
no need to set it again
* hwif->{channel,select_data,config_data} should be always zero
* autotune PIO also if CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA is defined
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Make remaining built-in only IDE host drivers modular, add ide-scan-pci.c
file for probing PCI host drivers registered with IDE core (special case
for built-in IDE and CONFIG_IDEPCI_PCIBUS_ORDER=y) and then take care of
the ordering in which all IDE host drivers are probed when IDE is built-in
during link time.
* Move probing of gayle, falconide, macide, q40ide and buddha (m68k arch
specific) host drivers, before PCI ones (no PCI on m68k), ide-cris (cris
arch specific), cmd640 (x86 arch specific) and pmac (ppc arch specific).
* Move probing of ide-cris (cris arch specific) host driver before cmd640
(x86 arch specific).
* Move probing of mpc8xx (ppc specific) host driver before ide-pnp (depends
on ISA and none of ppc platform that use mpc8xx supports ISA) and ide-h8300
(h8300 arch specific).
* Add "probe_vlb" kernel parameter to cmd640 host driver and update
Documentation/ide.txt accordingly.
* Make IDE_ARM config option visible so it can also be disabled if needed.
* Remove bogus comment from ide.c while at it.
v2:
* Fix two issues spotted by Sergei:
- replace ENOMEM error value by ENOENT in ide-h8300 host driver
- fix MODULE_PARM_DESC() in cmd640 host driver
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Add mpc8xx_ide_probe() to mpc8xx.c and call it from probe_for_hwifs().
* Convert ide_arm, ide-cris, ide-h8300, ide-pnp, buddha, falconide, gayle,
macide, q40ide, cmd640 and mpc8xx host drivers to use ide_device_add().
This removes dependency on ide_generic for these drivers so update
ide/Kconfig accordingly.
v2:
* ide_arm build fix (s/ide_device_idx/ide_device_add/)
(Thanks to Christoph Lameter <clameter@sgi.com> for reporting the problem).
Cc: Mikael Starvik <starvik@axis.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Make BLK_DEV_CMD640 select IDE_GENERIC.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Remove ide_init_port_data() call from ide_arm_init() and move
ide_arm_init() call from init_ide_data() to ide_init().
This patch is a preparation for the future changes (and as a side-effect
makes obsolete "idex=io[,ctl[,irq]]" kernel parameters work for ide_arm).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Rename init_hwif_data() to ide_init_port_data() and export it.
* For all users of ide_register_hw() with 'initializing' argument set
hwif->present and hwif->hold are always zero so convert these host
drivers to use ide_find_port()+ide_init_port_data()+ide_init_port_hw()
instead (also no need for init_hwif_default() call since the setup
done by it gets over-ridden by ide_init_port_hw() call).
* Drop 'initializing' argument from ide_register_hw().
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Add ide_init_port_hw() helper.
* rapide.c: convert rapide_locate_hwif() to rapide_setup_ports()
and use ide_init_port_hw().
* ide_platform.c: convert plat_ide_locate_hwif() to plat_ide_setup_ports()
and use ide_init_port_hw().
* sgiioc4.c: use ide_init_port_hw().
* pmac.c: add 'hw_regs_t *hw' argument to pmac_ide_setup_device(),
setup 'hw' in pmac_ide_{macio,pci}_attach() and use ide_init_port_hw()
in pmac_ide_setup_device().
This patch is a preparation for the future changes in the IDE probing code.
There should be no functionality changes caused by this patch.
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Jeremy Higdon <jeremy@sgi.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
'if (hwif->io_ports[IDE_DATA_OFFSET] != cmd_base)' is always true.
Cc: Jeremy Higdon <jeremy@sgi.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Fix build break of powerpc holly_defconfig:
In file included from arch/powerpc/platforms/embedded6xx/holly.c:24:
include/linux/ide.h:1206: error: 'CONFIG_IDE_MAX_HWIFS' undeclared here (not in a function)
There's no need to have a sized array in the prototype, might as well
turn it into a pointer.
It could probably be argued that large parts of the include file can be
covered under #ifdef CONFIG_IDE, but that's a larger undertaking.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Rename ide_device_add() to ide_device_add_all() and make it accept
'u8 idx[MAX_HWIFS]' instead of 'u8 idx[4]' as an argument.
* Add ide_device_add() wrapper for ide_device_add_all().
* Convert ide_generic_init() to use ide_device_add_all().
* Remove no longer needed ideprobe_init().
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Add hwif->chipset fixup identical to the one in ideprobe_init()
to ide_device_add().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
hwif->chipset should be set if the hwif is claimed by host driver.
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
hwif->chipset should be set if the hwif is claimed by host driver.
Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
After hwif_register_devices() IDE devices are ready to be used so
the way in which ide_device_add() works currently is racy for hosts
with serialized / IRQ sharing interfaces.
Fix ide_device_add() by looping over interfaces for probe_hwif(),
hwif_init() and hwif_register_devices() operations.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Host drivers using ide_register_hw() and 'initializing == 1':
* ide-pnp
- depends on ISA
* ide_arm
- ARM arch specific
- initialized before all other host drivers
* ide-cris
- CRIS arch specific => IDE_ARCH_OBSOLETE_INIT is not defined
- broken
* ide-h8300
- H8300 arch specific => IDE_ARCH_OBSOLETE_INIT is not defined, no PCI
* buddha/q40/gayle/macide/falconide
- M68K arch specific => IDE_ARCH_OBSOLETE_INIT is not defined, no PCI
Since the only host drivers which probe interfaces before the above ones are:
* ali14xx/dtc2278/ht6560b/qd65xx/umc8672
- depend on ISA
- require IDE_ARCH_OBSOLETE_INIT=y to work
* PCI ones
- depend on PCI
don't try to unregister interfaces if 'initializing == 1' in ide_register_hw()
(it is possible that built-in host drivers will claim all IDE interfaces but
later ide-pnp host driver will try to unregister them - this change fixes it).
Also skip hwif->hold check if 'initializing == 1' since it is set only by:
* pmac
- PPC && PMAC specific => no ISA
* au1xxx-ide
- MIPS && SOC_AU1200 specific => no ISA
and use ide_find_port() helper to find free ide_hwifs[] slot.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Assign drive->quirk_list in ->quirkproc implementations:
- hpt366.c::hpt3xx_quirkproc()
- pdc202xx_new.c::pdcnew_quirkproc()
- pdc202xx_old.c::pdc202xx_quirkproc()
* Make ->quirkproc void.
* Move calling ->quirkproc from do_identify() to probe_hwif().
* Convert it821x_fixups() to it821x_quirkproc() in it821x.c.
* Convert siimage_fixup() to sil_quirkproc() in siimage.c, also remove
no longer needed drive->present check from is_dev_seagate_sata().
* Convert ide_undecoded_slave() to accept 'drive' instead of 'hwif'
as an argument. Then convert ide_register_hw() to accept 'quirkproc'
argument instead of 'fixup' one.
* Remove no longer needed ->fixup method.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Dump taskfile HOB registers in ide_tf_load() (if DEBUG is defined).
* Remove no longer needed DEBUG code from __ide_do_rw_disk().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Merge ->dma_host_{on,off} methods into ->dma_host_set method
which takes 'int on' argument.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Enable/disable UDMA in atiixp_set_dma_mode().
* Remove no longer needed atiixp_dma_host_{on,off}() and save_mdma_mode[].
* Bump driver version.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Rename cris_dma_{on,off}() to cris_dma_host_{on,off}().
* Remove no longer needed ->dma_off_quietly
(IDE core has the needed code now).
* Make cris_dma_host_on() void.
I left fixing ide-cris after "kill dma_on/dma_off_quietly() methods"
patch because:
* Currently this driver is broken: cris_dma_on() (returns 'int')
is assigned to hwif->dma_host_on (returns 'void') so the driver
won't build.
* ->ide_dma_on method was missing so the driver OOPS-es on attempt
to enable DMA.
* drive->using_dma was never set/cleared so DMA wouldn't be used anyway.
Unfortunately it seems that ide-cris stays broken even after this patch:
* V10: <asm/arch-v10/ide.h> needs fixing
- ide_init_default_hwifs() should be removed
(IDE core no longer uses it)
- same for ide_init_hwif_ports() and ide_default_{irq,io_base}()
(they shouldn't be needed for ide-cris host driver)
* V32: I'm unable to find a place which defines ETRAX_ARCH_V32
but I'm leaving fixing this to CRIS gurus. :)
Cc: Mikael Starvik <starvik@axis.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Make ide_dma_off_quietly() and __ide_dma_on() always available.
* Drop "__" prefix from __ide_dma_on().
* Check for presence of ->dma_host_on instead of ->ide_dma_on.
* Convert all users of ->ide_dma_on and ->dma_off_quietly methods
to use ide_dma_on() and ide_dma_off_quietly() instead.
* Remove no longer needed ->ide_dma_on and ->dma_off_quietly methods
from ide_hwif_t.
* Make ide_dma_on() void.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Add ide_toggle_bounce() call to ->ide_dma_on/->dma_off_quietly
methods so they match generic __ide_dma_on()/ide_dma_off_quietly().
Since there is no PCI device there should be no functionality
changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Add ide_toggle_bounce() call to ->ide_dma_on/->dma_off_quietly
methods so they match generic __ide_dma_on()/ide_dma_off_quietly().
Since there is no PCI device there should be no functionality
changes caused by this patch.
Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Add ide_toggle_bounce() call to ->ide_dma_on/->dma_off_quietly
methods so they match generic __ide_dma_on()/ide_dma_off_quietly().
Tested on Altix by Jeremy.
Acked-by: Jeremy Higdon <jeremy@sgi.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Fix SWDMA/MWDMA masks in cy82c693_chipset.
* Add IDE_HFLAG_CY82C693 host flag and use it in ide_tune_dma() to
check whether the DMA should be enabled even if ide_max_dma_mode()
fails.
* Convert cy82c693_dma_enable() to become cy82c693_set_dma_mode()
and remove no longer needed cy82c693_ide_dma_on(). Then set
IDE_HFLAG_CY82C693 instead of IDE_HFLAG_TRUST_BIOS_FOR_DMA in
cy82c693_chipset.
* Bump driver version.
As a result of this patch cy82c693 driver will configure and use DMA on
all SWDMA0-2 and MWDMA0-2 capable ATA devices instead of relying on BIOS.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Mask device DMA masks by ATA_{S,M}WDMA2 in cy82c693_ide_dma_on().
* Remove clipping of DMA modes by id->tDMA in cy82c693_dma_enable():
- id->tDMA may not be defined on newer devices
- id->vendor6/id->tDMA word is in LE endianness
(cy82c693 seems to be Alpha specific though)
* Bump driver version.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Set the correct hwif->dma_base for the second channel in
ide_get_or_set_dma_base().
* Remove DMA enable code from cs5520_set_pio_mode(), this can
be handled by the generic ->dma_host_on method now.
* Add VDMA check to ide_config_drive_speed().
* drive->using_dma was never enabled since cs5520 host driver's
->ide_dma_on method overrided the generic ->ide_dma_on (so
__ide_dma_on() was never called, drive->using_dma was never set
and VDMA was never used since it depends on drive->using_dma).
Fix it by using ->dma_host_on method instead of ->ide_dma_on
(also add matching ->dma_host_off method).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
IDE core guarantees that ->set_dma_mode will be called only
for DMA modes set in SWDMA/MWDMA/UDMA masks.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Program register 0x40 in sl82c105_resetproc().
* Remove no longer needed sl82c105_selectproc() and pci_set_drvdata() calls.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Program DMA timings in sl82c105_dma_start() (->dma_start method)
before starting DMA transfer.
* Add sl82c105_dma_end() (->ide_dma_end method) to switch back to
PIO timings when DMA transfer is complete.
* In sl82c105_set_pio_mode() program timings regardless of ->using_dma
setting and in sl82c105_set_dma_mode() only cache the new timings.
* Remove no longer needed sl82c105_{ide_dma_on,off_quietly}().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (200 commits)
[SCSI] usbstorage: use last_sector_bug flag universally
[SCSI] libsas: abstract STP task status into a function
[SCSI] ultrastor: clean up inline asm warnings
[SCSI] aic7xxx: fix firmware build
[SCSI] aacraid: fib context lock for management ioctls
[SCSI] ch: remove forward declarations
[SCSI] ch: fix device minor number management bug
[SCSI] ch: handle class_device_create failure properly
[SCSI] NCR5380: fix section mismatch
[SCSI] sg: fix /proc/scsi/sg/devices when no SCSI devices
[SCSI] IB/iSER: add logical unit reset support
[SCSI] don't use __GFP_DMA for sense buffers if not required
[SCSI] use dynamically allocated sense buffer
[SCSI] scsi.h: add macro for enclosure bit of inquiry data
[SCSI] sd: add fix for devices with last sector access problems
[SCSI] fix pcmcia compile problem
[SCSI] aacraid: add Voodoo Lite class of cards.
[SCSI] aacraid: add new driver features flags
[SCSI] qla2xxx: Update version number to 8.02.00-k7.
[SCSI] qla2xxx: Issue correct MBC_INITIALIZE_FIRMWARE command.
...
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
[CRYPTO] hifn795x: Disallow built-in hifn795x when HW_RANDOM is m
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2: (31 commits)
ocfs2: clean up bh null checks
ocfs2: document access rules for blocked_lock_list
configfs: file.c fix possible recursive locking
configfs: dir.c fix possible recursive locking
configfs: Remove EXPERIMENTAL
ocfs2: bump version number
ocfs2/dlm: Clear joining_node on hearbeat node down
ocfs2: convert byte order of constant instead of variable
ocfs2: Update default cluster timeouts
ocfs2: printf fixes
ocfs2: Use generic_file_llseek
ocfs2: Safer read_inline_data()
ocfs2: Silence false lockdep warnings
[PATCH 2/2] ocfs2: cluster aware flock()
[PATCH 1/2] ocfs2: add flock lock type
ocfs2: Local alloc window size changeable via mount option
ocfs2: Support commit= mount option
ocfs2: Add missing permission checks
[PATCH 2/2] ocfs2: Implement group add for online resize
[PATCH 1/2] ocfs2: Add group extend for online resize
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (67 commits)
fix drivers/ata/sata_fsl.c double-decl
[libata] Prefer SCSI_SENSE_BUFFERSIZE to sizeof()
pata_legacy: Merge winbond support
ata_generic: Cenatek support
pata_winbond: error return
pata_serverworks: Fix cable types and cosmetics
pata_mpc52xx: remove un-needed assignment
libata: fix off-by-one in error categorization
ahci: factor out AHCI enabling and enable AHCI before reading CAP
ata_piix: implement SIDPR SCR access
ata_piix: convert to prepare - activate initialization
libata: factor out ata_pci_activate_sff_host() from ata_pci_one()
[libata] Prefer SCSI_SENSE_BUFFERSIZE to sizeof()
pata_legacy: resychronize with upstream changes and resubmit
[libata] pata_legacy: typo fix
[libata] pata_winbond: update for new ->data_xfer hook
pata_pcmcia: convert to new data_xfer prototype
libata annotations and fixes
libata: use dev_driver_string() instead of "libata" in libata-sff.c
ata_piix: kill unused constants and flags
...
|
|
If we know a buffer_head is non-null, then brelse() is unnecessary and
put_bh() can be used instead. Also, an explicit check for NULL is
unnecessary when using brelse(). This patch only covers buffer_head_io.c and
resize.c, which have recently added code which exhibits this problem.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
|
|
ocfs2_super->blocked_lock_list and ocfs2_super->blocked_lock_count have some
usage restrictions which aren't immediately obvious to anyone reading the
code. It's a good idea to document this so that we avoid making costly
mistakes in the future.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
|
|
configfs_register_subsystem() with default_groups triggers recursive locking.
it seems that mutex_lock_nested is needed.
=============================================
[ INFO: possible recursive locking detected ]
2.6.24-rc6 #145
---------------------------------------------
swapper/1 is trying to acquire lock:
(&sb->s_type->i_mutex_key#3){--..}, at: [<c40c9a9e>] configfs_add_file+0x2e/0x70
but task is already holding lock:
(&sb->s_type->i_mutex_key#3){--..}, at: [<c40ca985>] configfs_register_subsystem+0x55/0x130
other info that might help us debug this:
1 lock held by swapper/1:
#0: (&sb->s_type->i_mutex_key#3){--..}, at: [<c40ca985>] configfs_register_subsystem+0x55/0x130
stack backtrace:
Pid: 1, comm: swapper Not tainted 2.6.24-rc6 #145
[<c40053ba>] show_trace_log_lvl+0x1a/0x30
[<c4005e82>] show_trace+0x12/0x20
[<c400687e>] dump_stack+0x6e/0x80
[<c404ec72>] __lock_acquire+0xe62/0x1120
[<c404efb2>] lock_acquire+0x82/0xa0
[<c43fda88>] mutex_lock_nested+0x98/0x2e0
[<c40c9a9e>] configfs_add_file+0x2e/0x70
[<c40c9b0c>] configfs_create_file+0x2c/0x40
[<c40ca639>] configfs_attach_item+0x139/0x220
[<c40ca734>] configfs_attach_group+0x14/0x140
[<c40ca7e9>] configfs_attach_group+0xc9/0x140
[<c40ca9f6>] configfs_register_subsystem+0xc6/0x130
[<c45c8186>] init_netconsole+0x2b6/0x300
[<c45a75f2>] kernel_init+0x142/0x320
[<c4004fb3>] kernel_thread_helper+0x7/0x14
=======================
Signed-off-by: Joonwoo Park <joonwpark81@gmail.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
|
|
configfs_register_subsystem() with default_groups triggers recursive locking.
it seems that mutex_lock_nested is needed.
=============================================
[ INFO: possible recursive locking detected ]
2.6.24-rc6 #141
---------------------------------------------
swapper/1 is trying to acquire lock:
(&sb->s_type->i_mutex_key#3){--..}, at: [<c40ca76f>] configfs_attach_group+0x4f/0x190
but task is already holding lock:
(&sb->s_type->i_mutex_key#3){--..}, at: [<c40ca9d5>] configfs_register_subsystem+0x55/0x130
other info that might help us debug this:
1 lock held by swapper/1:
#0: (&sb->s_type->i_mutex_key#3){--..}, at: [<c40ca9d5>] configfs_register_subsystem+0x55/0x130
stack backtrace:
Pid: 1, comm: swapper Not tainted 2.6.24-rc6 #141
[<c40053ba>] show_trace_log_lvl+0x1a/0x30
[<c4005e82>] show_trace+0x12/0x20
[<c400687e>] dump_stack+0x6e/0x80
[<c404ec72>] __lock_acquire+0xe62/0x1120
[<c404efb2>] lock_acquire+0x82/0xa0
[<c43fdad8>] mutex_lock_nested+0x98/0x2e0
[<c40ca76f>] configfs_attach_group+0x4f/0x190
[<c40caa46>] configfs_register_subsystem+0xc6/0x130
[<c45c8186>] init_netconsole+0x2b6/0x300
[<c45a75f2>] kernel_init+0x142/0x320
[<c4004fb3>] kernel_thread_helper+0x7/0x14
=======================
Signed-off-by: Joonwoo Park <joonwpark81@gmail.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
|
