| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Whenever mac80211 gives us a legacy rate bitmap in the context of the
5 GHz band, we need to remember to shift the bitmap left by 5 positions
before giving it to the firmware, as the firmware follows the bitmap
bit assignment of the 2.4 GHz rate table even if we're on the 5 GHz
band, and the 2.4 GHz rate table includes five non-OFDM rates at the
start that are not valid in the 5 GHz band.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The mwl8k firmware uses indices into the 2.4 GHz band rate table for
the receive descriptor channel field even if the packet was received
on a 5 GHz channel, while mac80211 expects an index into the 5 GHz
band rate table when packets are received on the 5 GHz band, which
presents a mismatch as the 5 GHz band rate table lacks the five
non-OFDM rates that the 2.4 GHz rate table starts with.
To handle this properly, we need to substract 5 from the rate index
field if the packet was received on a 5 GHz channel (and was not
received at an MCS rate).
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
So that we can make 2.4 GHz and 5 GHz band registration conditional
on the capability bitmask returned by the firmware.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
To prepare for adding 5 GHz band/channels/rates.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
0x2a43 is a single-band (2.4GHz only) 88w8366 mini-PCIe card.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
By storing the sequence counter in << 4 format, like other drivers do.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add MODULE_FIRMWARE tags for the mwl8k firmware images that don't
have them yet, and move them to where the firmware image names are
declared.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
wl1251 firmware supports U-APSD just with a simple queue configuration
change so enable it.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The qos null data template is needed for U-APSD.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The header can be used to create qos nullfunc frames, for example.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
To make U-APSD client mode effective, we must not wake up from dynamic power
save when transmitting frames. So if dynamic power save is enabled, it needs
check the queue the transmitted packet is in and decide if we need to wake
up or not.
In a perfect world, where all packets would have correct QoS tags, U-APSD
enabled queues should not trigger wakeup from power save. But in the real
world, where very few packets have correct QoS tags, this won't work. For
example, if only voip class has U-APSD enabled and we send a packet in voip
class, but the packets we receive are in best effort class, we would receive
the packets with the legacy power save method. And that would increase
latencies too much from a voip application point of view.
The workaround is to enable U-APSD for all qeueus and still use dynamic ps
wakeup for all other queues except voip. That way we can still save power
with a voip application and not sacrifice latency. Normal traffic (in
background, best effort or video class) would still trigger wakeup from
dynamic power save.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Currently dynamic ps check is in ieee80211_xmit(), but it's cleaner
to have a separate tx handler for this. Also this is a prerequisite for
U-APSD client mode which needs to know the queue frame is in.
Also need_dynamic_ps() function is embedded to the tx handler.
No functional changes expect that the code is run in a later phase than
originally.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Because it's not yet decided how to configure which queues are U-APSD
enabled, add a debugfs interface for testing purposes.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add Unscheduled Automatic Power-Save Delivery (U-APSD) client support. The
idea is that the data frames from the client trigger AP to send the buffered
frames with ACs which have U-APSD enabled. This decreases latency and makes it
possible to save even more power.
Driver needs to use IEEE80211_HW_UAPSD to enable the feature. The current
implementation assumes that firmware takes care of the wakeup and
hardware needing IEEE80211_HW_PS_NULLFUNC_STACK is not yet supported.
Tested with wl1251 on a Nokia N900 and Cisco Aironet 1231G AP and running
various test traffic with ping.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The type argument to DEBUGFS_ADD() isn't used
and can be removed, it's around from before
the conversion to debugfs_remove_recursive().
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Since commit "mwl8k: handle station database update for AP's sta entry
via ->sta_notify()", mwl8k every now and then gets a command timeout
when ifconfig'ing a STA interface down. This turns out to be due to
mwl8k_stop() being called while the work queue item that was scheduled
by mwl8k_sta_notify() to remove the STA entry for the associated AP is
still queued, and the former disables interrupts so that when the
latter eventually runs, a command completion interrupt is never seen.
Fix this by changing ieee80211_stop_device() so that the workqueue is
flushed before drv_stop() is called, instead of doing it the other way
around as is done now. (As ->stop() is allowed to sleep, there isn't
any reason for drivers to queue work from within it.)
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
void pointers do not need to be cast to other pointer types.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When setting invalid byte count in txq byte count table, read pointer
should be used instead of write pointer.
Reported-by: Guo, Chaohong <chaohong.guo@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
"RADAR_NOTIFICATION" host command is not used and not supported by uCode,
remove it from driver code.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Update data structure to match latest statistics report from uCode.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
mac80211 do not check the return code now, what if mac80211 does start
using the return code? IEEE80211_AMPDU_TX_OPERATIONAL is a valid action,
just iwlwifi driver do not need to take any action for it; so instead of
return "-EINVAL", it is a good program practice to return "-EOPNOTSUPP"
to make sure mac80211 will not get wrong impression.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
sparse pointed out that I made a mistake converting
the return value of ieee80211_assoc_success to bool,
this place should return false instead of one of the
enum values (which would be true).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Like how TX reclaim is done in a tasklet, move receive processing
to tasklet context as well. This can have nice benefits for CPU
utilisation and throughput, especially at 3-stream rates.
(Use the same CLEAR_SEL trick as the TX reclaim tasklet does, to
avoid having to touch the interrupt mask registers.)
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
By making use of the CLEAR_SEL feature of the mwl8k host interface
interrupt controller, we can keep the TX_DONE interrupt source masked
while the transmit reclaim tasklet is running (NAPI style) without
having to touch the interrupt controller's interrupt mask register
when entering or exiting polling mode, and without having to do any
more register reads/writes than we do now.
When CLEAR_SEL is enabled on the TX_DONE interrupt source, reading
the interrupt status register will clear the TX_DONE status bit if
it was set, allowing it to be set again if a new TX_DONE event arrives
while we are running the TX reclaim tasklet, but such a new event will
then not trigger another PCI interrupt until a zero is written to the
TX_DONE interrupt status register bit.
I.e., if we write a zero to the TX_DONE interrupt source bit in the
interrupt status register when the TX reclaim tasklet thinks it's
done, a PCI interrupt will be triggered if a new TX_DONE event arrived
from the hardware between us deciding that there is no more work to do
and re-enabling the TX_DONE interrupt source, thereby avoiding the
classic NAPI poll mode exit race that would otherwise occur.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add a limit argument to mwl8k_txq_reclaim(), to allow limiting the
number of packets that it will reclaim, and make it return the number
of packets that it reclaimed.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add support for creating AP interfaces, and enabling beaconing.
This allows running a basic AP (11b/g mode only for now).
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
STA firmware uses UPDATE_STADB to manipulate the hardware station
database, whereas AP firmware uses SET_NEW_STN -- this implements the
latter, and hooks it into mwl8k_sta_notify(), to be used if we're
running on AP firmware.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
As with the STA version, unicast will use auto rate adaptation, but
the AP version allows setting the rates to be used for management and
multicast transmissions, which can be set based on the BSS basic rate
set.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
As we always use the auto rate adaptation feature and never pass in
a rate table, USE_FIXED_RATE can be simplified somewhat. While we're
at it, rename it to *_sta, as this is the STA version of the command.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
While it is reasonable to expect that at least one transmit ring entry
will be processed per second while we are waiting for the transmit
rings to drain, the firmware can end up doing batching of transmit ring
status writeback, which means that the transmit rings can appear stuck
for more than a second at a time.
Bump the TX drain wait timeout up from 1 to 5 seconds to account for
this.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The comment and code in mwl8k_cmd_set_edca_params() suggest that the
mapping between SET_EDCA_PARAMS queue numbers and transmit rings isn't
actually 1:1, while tests show that the mapping is in fact 1:1. So,
get rid of the transmit queue 0/1 swapping.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
If frames are transmitted on 4-addr ap vlan interfaces with no station,
they end up being transmitted unencrypted, even if the ap interface
uses WPA. This patch add some sanity checking to make sure that this
does not happen.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Since the per-vif station changes, sta_info_get on the ap sdata no
longer returns entries for stations on ap vlans. This causes issues
with hostapd, which currently always passes the ap interface name to
nl80211 calls. This patch provides bug compatibility with the earlier
versions until hostapd is fixed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
To detect incoming 4-addr stations, hostapd needs to receive a 4-addr
data frame from the remote station, so that it can create the AP VLAN
for it. With this patch, the mlme code emits a 4-addr nullfunc frame
immediately after assoc. On the AP side it also drops 4-addr nullfunc
frames to the cooked monitor mode interface, if the interface hasn't
been fully set up to receive 4-addr data frames yet.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
mac80211 passes appropriate flags indicating whether
monitor mode is being used. Use this to set the HW opmode.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This file can be used to track frame reception errors.
PHY error counts are also added.
Location: ath9k/phy#/recv
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The TX queues have to be stopped during an
internal reset. Not handling this would result
in packet loss - fix this.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The device initialization and termination functions
were messy and convoluted. Introduce helper functions
to clarify init_softc() and simplify things in general.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
sc_flags has slowly become a kitchen sink over time.
Move powersave related flags to a separate variable.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Move initialization/de-initialization related
code to this file.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Move all LED/RFKILL/BTCOEX related code
to gpio.c
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This enhances the way we parse country IEs to minimize
the number of regulatory rules that we create. It also fixes
our current implementation which treated country IE triplets
with only one channel as one independed regulatory rule even
though adjecent rules were also being provided.
Without this patch APs which send country IE information with
a channel triplet for each individual channel will force cfg80211
to deny HT40 operation as a regulatory rule would have been created
independently for each channel and as such configured only for
20 MHz operation.
Although 802.11n APs which send country IEs triplets in this fassion
are likely rare Benoit reports this against the Ubiquity NanoStation M5,
with Country "FR" and HT40 enabled.
Since we now have a helper which parses the triplets in intermediate
steps we now take care extra care to process padding.
Reported-by: Benoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The max power from each country IE triplet was being ignored.
This fix isn't critical as CRDA was always being used for the lower
limit, but we should process it in case the AP still wants to
decrease power output even more for whatever reason.
Reported-by: Benoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
