| Age | Commit message (Collapse) | Author |
|---|
|
This patch removes redundant board specific interrupt code for boards
using sh775x processors and 4 IRQ lines in "Individual Interrupt Mode"
aka IRLM.
Three boards are affected: sh03, snapgear and titan.
The right way to do this is to use cpu specific code provided by intc.
A nice side effect is that sh03 now compiles, board not BROKEN any more.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
All SH-4 parts have a 4-digit year, while the SH-3 parts typically
only use a 2-digit one. The SH7705, SH7710, and SH7712 SH-3 parts
however opted to extend it to 4-digit and still look and act like
an SH-3 RTC in all other ways.
This adds a capability flag (RTC_CAP_4_DIGIT_YEAR) that these
corner-case CPU subtypes can set in their platform data and cleans
up some of the ifdef mess in the driver as a result.
Reported-by: Markus Brunner <super.firetwister@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Wire up CPU#0 URAM as node 1 on SH-X3.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch converts the cpu specific interrupt setup code for x3 from
intc2 to intc. New vectors are also added to match the preliminary
information.
Use plat_irq_setup_pins() to select between IRQ and IRL mode for IRQ0-3.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
The intc tables for sh3 currently contain a typo where the bit
fields in IPRD are mixed up for IRQ4 and IRQ5. This patch makes
sure the correct bit fields are used - all according to the
datasheets.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
The cache disabling stuff screwed up some of the sh4 nommu
builds, fix it up again.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
The new intc code handles IRQ3 and IRQ7 in the cpu specific code
already, so there is no reason to duplicate that here.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch converts the cpu specific interrupt setup code for sh7760
from ipr + intc2 to intc. New vectors are also added to match the
information provided by the datasheet.
Vectors for IRQ4-IRQ7 are enabled by default. Use plat_irq_setup_pins()
if pins IRL0-3 should be used in IRLM mode.
The patch also adds the SIM block to the serial port platform data.
Version two of this patch fixes MMCIF problems reported by Manuel Lauss.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch converts the cpu specific interrupt setup code for sh7785
from intc2 to intc. New vectors are also added to match the information
provided by the datasheet.
No IRQ/IRL pin vectors are enabled by default. Use plat_irq_setup_pins()
to select between IRL and IRQ mode.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This reworks the cache mode configuration in Kconfig, and allows for
explicit selection of write-back/write-through/off configurations.
All of the cache flushing routines are optimized away for the off
case.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch makes sure that the sh7710 specific ipsec vector is missing
if building for a sh7712. All according to the datasheet.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch adds a few missing vectors for sh7707. The only interrupt
controller differences between sh7707 and sh7709 seem to be added
vectors for one LCD controller and two PCMCIA slots.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch unifies the cpu specific interrupt setup code for
sh7706, sh7707, sh7708 and sh7709 and moves the code into a new
file called setup-sh770x.c. It makes sense to share the setup code
between these processors because most hardware blocks are identical
from a software point of view. With this patch the sh770x processors
now have a complete set of vectors that match with the information
provided by the data sheets. This is a big improvement for sh7708.
Vectors for IRQ4 and IRQ5 are enabled by default. Use
plat_irq_setup_pins() if pins IRQ0-3 should be used in IRQ mode.
This patch also unifies the platform device setup code which means
that the rtc driver now has platform data for all sh770x processors.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch converts the cpu specific interrupt setup code
for sh7710 from ipr to intc. While at it new vectors are added
to match the information provided by the datasheet. Version two
simplifies the Kconfig part.
Vectors for IRQ4 and IRQ5 are enabled by default. Use
plat_irq_setup_pins() if pins IRQ0-3 should be used in IRQ mode.
This patch also adds sh7710 specific platform data for the rtc
driver. The base address of SCIF1 is adjusted to match the
datasheet.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch converts the cpu specific interrupt setup code for
sh7705 from ipr to intc. While at it new vectors are added to
match the information provided by the datasheet.
Vectors for IRQ4 and IRQ5 are enabled by default.
Use plat_irq_setup_pins() if pins IRQ0-3 should be used in IRQ mode.
This patch also adds sh7705 specific platform data for the rtc driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] ahci: add ATI SB800 PCI IDs
libata-sff: Fix documentation
libata: Update the blacklist with a few more devices
|
|
This simplifies signalfd code, by avoiding it to remain attached to the
sighand during its lifetime.
In this way, the signalfd remain attached to the sighand only during
poll(2) (and select and epoll) and read(2). This also allows to remove
all the custom "tsk == current" checks in kernel/signal.c, since
dequeue_signal() will only be called by "current".
I think this is also what Ben was suggesting time ago.
The external effect of this, is that a thread can extract only its own
private signals and the group ones. I think this is an acceptable
behaviour, in that those are the signals the thread would be able to
fetch w/out signalfd.
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
we upgraded the kernel of a nfs-server from 2.6.17.11 to 2.6.22.6. Since
then we get the message
lockd: too many open TCP sockets, consider increasing the number of nfsd threads
lockd: last TCP connect from ^\\236^\É^D
These random characters in the second line are caused by a bug in
svc_tcp_accept.
(Note: there are two previous __svc_print_addr(sin, buf, sizeof(buf))
calls in this function, either of which would initialize buf correctly;
but both are inside "if"'s and are not necessarily executed. This is
less obvious in the second case, which is inside a dprintk(), which is a
macro which expands to an if statement.)
Signed-off-by: Wolfgang Walter <wolfgang.walter@studentenwerk.mhn.de>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
ATI/AMD SB800 shares some device IDs with SB700,
and SB800 adds two more device IDs:0x4394,0x4395.
Signed-off-by: henry su <henry.su.ati@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Code moved to ioread/iowrite but the comment didn't
Also note a posting issue
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[BNX2]: Add PHY workaround for 5709 A1.
[PPP] L2TP: Fix skb handling in pppol2tp_xmit
[PPP] L2TP: Fix skb handling in pppol2tp_recv_core
[PPP] L2TP: Disallow non-UDP datagram sockets
[PPP] pppoe: Fix double-free on skb after transmit failure
[PKT_SCHED]: Fix 'SFQ qdisc crashes with limit of 2 packets'
[NETFILTER]: MAINTAINERS update
[NETFILTER]: nfnetlink_log: fix sending of multipart messages
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
sky2: version 1.18
sky2: receive FIFO checking
sky2: fe+ chip support
sky2: reorganize chip revision features
sky2: ethtool speed report bug
sky2: fix VLAN receive processing (resend)
phy: export phy_mii_ioctl
myri10ge: Add support for PCI device id 9
|
|
Update version number
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
A driver writer from another operating system hinted that
the versions of Yukon 2 chip with rambuffer (EC and XL) have
a hardware bug that if the FIFO ever gets completely full it
will hang. Sounds like a classic ring full vs ring empty wrap around
bug.
As a workaround, use the existing watchdog timer to check for
ring full lockup.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Add support for newest Marvell chips.
The Yukon FE plus chip is found in some not yet released laptops.
Tested on hardware evaluation boards.
This version of the patch is for 2.6.23. It supersedes
the two previous patches that are sitting in netdev-2.6 (upstream branch).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This patch should cause no functional changes in driver behaviour.
There are (too) many revisions of the Yukon 2 chip now. Instead of
adding more conditionals based on chip revision; rerganize into a
set of feature flags so adding new versions is less problematic.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
On 100mbit versions, the driver always reports gigabit speed
available. The correct modes are already computed, then overwritten.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The length check for truncated frames was not correctly handling
the case where VLAN acceleration had already read the tag.
Also, the Yukon EX has some features that use high bit of status
as security tag.
Signed-off-by: Pierre-Yves Ritschard <pyr@spootnik.org>
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Initialization of ohci1394 was broken according to one reporter if the
driver was statically linked, i.e. not built as loadable module. Dmesg:
PCI: Device 0000:02:07.0 not available because of resource collisions
ohci1394: Failed to enable OHCI hardware.
This was reported for a Toshiba Satellite 5100-503. The cause is commit
8df4083c5291b3647e0381d3c69ab2196f5dd3b7 in Linux 2.6.19-rc1 which only
served purposes of early remote debugging via FireWire. This
functionality is better provided by the currently out-of-tree driver
ohci1394_earlyinit. Reversal of the commit was OK'd by Andi Kleen.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Add the DIS_EARLY_DAC PHY workaround for 5709 A1. Without it, link
sometimes does not come up.
Update version to 1.6.5.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch makes pppol2tp_xmit call skb_cow_head so that we don't modify
cloned skb data. It also gets rid of skb2 we only need to preserve the
original skb for congestion notification, which is only applicable for
ppp_async and ppp_sync.
The other semantic change made here is the removal of socket accounting
for data tranmitted out of pppol2tp_xmit. The original code leaked any
existing socket skb accounting. We could fix this by dropping the
original skb owner. However, this is undesirable as the packet has not
physically left the host yet.
In fact, all other tunnels in the kernel do not account skb's passing
through to their own socket. In partciular, ESP over UDP does not do
so and it is the closest tunnel type to PPPoL2TP. So this patch simply
removes the socket accounting in pppol2tp_xmit. The accounting still
applies to control packets of course.
I've also added a reminder that the outgoing checksum here doesn't work.
I suppose existing deployments don't actually enable checksums.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function pppol2tp_recv_core doesn't handle non-linear packets properly.
It also fails to check the remote offset field.
This patch fixes these problems. It also removes an unnecessary check on
the UDP header which has already been performed by the UDP layer.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the addition of UDP-Lite we need to refine the socket check so
that only genuine UDP sockets are allowed through.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When I got rid of the second packet in __pppoe_xmit I created
a double-free on the skb because of the goto abort on failure.
This patch removes that.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update netfilter list addresses and an old email address of myself.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The following patch fixes the handling of netlink packets containing
multiple messages.
As exposed during netfilter workshop, nfnetlink_log was overwritten the
message type of the last message (setting it to MSG_DONE) in a multipart
packet. The consequence was libnfnetlink to ignore the last message in the
packet.
The following patch adds a supplementary message (with type MSG_DONE) af
the end of the netlink skb.
Signed-off-by: Eric Leblond <eric@inl.fr>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Emil Medve points out that this documentation file uses CRLF line
endings, which means that if you use
[core]
autocrlf=input
(which makes sense if you ever develop under Windows, for example, or if
you use other broken tools) in your git config, git will always complain
about the file being dirty.
This removes the bogus DOS line endings, and removes whitespace at the
end of line.
Cc: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There's an obvious typo in arch/i386/boot/header.S (in your
linux-2.6-x86setup.git) that I noticed by just studying the code.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
wakeup.S looks at the video mode number from the setup header and
looks to see if it is a VESA mode. Unfortunately, the decoding is
done incorrectly and it will attempt to frob the VESA BIOS for any
mode number 0x0200 or larger. Correct this, and remove a bunch of #if
0'd code.
Massive thanks to Jeff Chua for reporting the bug, and suffering
though a large number of experiments in order to track this problem
down.
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Canonicalize the video mode number as presented to the kernel. The
video mode number may be user-entered (e.g. ASK_VGA), an alias
(e.g. NORMAL_VGA), or a size specification, and that confuses the
suspend wakeup code.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Export phy_mii_ioctl, so network drivers can use it when built
as modules too.
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched:
sched: fix invalid sched_class use
sched: add /proc/sys/kernel/sched_compat_yield
|
|
Given an illegal selinux option it was possible for match_token to work in
random memory at the end of the match_table_t array.
Note that privilege is required to perform a context mount, so this issue is
effectively limited to root only.
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: James Morris <jmorris@namei.org>
|
|
When using rt_mutex, a NULL pointer dereference is occurred at
enqueue_task_rt. Here is a scenario;
1) there are two threads, the thread A is fair_sched_class and
thread B is rt_sched_class.
2) Thread A is boosted up to rt_sched_class, because the thread A
has a rt_mutex lock and the thread B is waiting the lock.
3) At this time, when thread A create a new thread C, the thread
C has a rt_sched_class.
4) When doing wake_up_new_task() for the thread C, the priority
of the thread C is out of the RT priority range, because the
normal priority of thread A is not the RT priority. It makes
data corruption by overflowing the rt_prio_array.
The new thread C should be fair_sched_class.
The new thread should be valid scheduler class before queuing.
This patch fixes to set the suitable scheduler class.
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
|
|
add /proc/sys/kernel/sched_compat_yield to make sys_sched_yield()
more agressive, by moving the yielding task to the last position
in the rbtree.
with sched_compat_yield=0:
PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND
2539 mingo 20 0 1576 252 204 R 50 0.0 0:02.03 loop_yield
2541 mingo 20 0 1576 244 196 R 50 0.0 0:02.05 loop
with sched_compat_yield=1:
PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND
2584 mingo 20 0 1576 248 196 R 99 0.0 0:52.45 loop
2582 mingo 20 0 1576 256 204 R 0 0.0 0:00.00 loop_yield
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
|
|
Add support for new Myri-10G boards with PCI device id 9.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] cpu-bugs64.c: GCC 3.3 constraint workaround
[MIPS] DEC: Initialise ioasic_ssr_lock
|
