| Age | Commit message (Collapse) | Author |
|---|
|
This patch fixes a problem in the ieee80211 probe response and beacon
reception code that would use the packet statistics for a network even
if they were received on a channel other than that which the network
exists on.
This causes a problem in overlapping channels where, for example, a
strong AP on channel 2 could have its beacons received on channels 1 and
3, but at much lower signal levels. If scanning was done sequentially,
this means the beacon received on channel 3 would update the AP's signal
level as being much lower than it really is, which subsequently could
cause that AP to be passed over and an alternate AP selected.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch modifies the driver to support the ipw2200-fw-3.0 image format.
The 3.0 fw image does not add any new capabilities, but as a result of
image format changes, it should fix two problems experienced by users:
1) Race conditions with the request_firmware interface and udev/hotplug
are improved as only a single request_firmware call is now required to
load the firmware and microcode (vs. 3 separate calls previously)
2) The monitor mode firmware (sniffer) is now packaged with the correct
boot image so it can now function without frequent restarts.
Note: Once you apply this patch, you will also need to upgrade your
firmware image to the 3.0 version available from:
http://ipw2200.sf.net/firmware.php
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The patch allows the user to set the handover threshold, i.e. the number
of consecutively missed beacons that will trigger a roaming attempt. The
disassociation threshold is set to 3 times the handover threshold.
Signed-off-by: Olivier Hochreutiner <olivier.hochreutiner@epfl.ch>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This forces one antenna or the other, if the background noise is
significantly quieter in one than the other. It favors the quieter
antenna, and won't kick in unless the difference is significant.
Signed-off-by: Cahill, Ben M <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Set a meaningful silence threshold value (replacing our previous "0"
default), which gets rid of the gratuitous "Link deterioration"
notifications that we've been receiving from firmware. This
notification feature tells the driver information to help it determine
when to pre-emptively restart the firmware/ucode in anticipation of
firmware errors! But since setting this new threshold, I haven't seen
any such notifications. At least it keeps the logs a little less busy.
Signed-off-by: Cahill, Ben M <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Currently iwlist ethX freq[uency]/channel lists all the channels the card
supported for the current region, which includes some channels can only
be used in infrastructure mode. This patch filters these channels out if
the card is currently in ad-hoc mode.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When loading the ipw2200 module with disabled=1, rf_kill is activated after
every mode change. This is caused by ipw_sw_reset() is called when a mode
is changed. The patch fixed the problem by distinguishing the purposes with
the 'option' paramenter.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
wpa_supplicant needs to set wpa_enabled unconditionally, with this check
it hasn't been possible to connect to non-WPA networks using wpa_supplicant.
So remove below check.
if (priv->ieee->wpa_enabled &&
network->wpa_ie_len == 0 && network->rsn_ie_len == 0)
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch does two things. It uses the parameter IW_QUAL_DBM which is new
in WE-19 to cause signal level and noise to be reported in dBm by the
wireless tools. It also defines the signal level as an unsigned integer
so that the signal level will be reported by iwlist iface scan.
Signed-off-by: Bill Moss <bmoss@clemson.edu>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
replace ipw2200 specific frame_hdr_len() with generic
ieee80211 routine ieee80211_get_hdrlen()
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Only on CONFIG_IPW2200_DEBUG is not defined
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The patch roll back the change we made to support for the ability to
start/stop independent Tx queues within a single net device in order to
support 802.11e QoS. We need to be able to indicate to the upper layers
that packets of a given priority can not be sent any more without halting
transmission of all packets, and without rescheduling high priority packets
down to the next priority level.
So we return NETDEV_TX_BUSY in this case and rely on the stack would
take care of rescheduling... which it apparently does immediately and
consumes the CPU. This caused the ksoftirqd kernel thread consuming almost
all the CPU...
To put the code back to the way it was before we made these changes we
put the call netif_queue_stop back in ipw_tx_skb. This effectively
disables multiple priority based transmit queues for 802.11e, but given
that its broken anyway...
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Given the amount of support requests for the meaning of the geography code
I've written a patch for printing this information on module load no matter
the debug level.
I've also added a section to the README.ipw2200 file listing the geography
codes and their meaning.
Signed-off-by: Henrik Brix Andersen <brix@gentoo.org>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch makes the needlessly global function ipw_qos_current_mode()
static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
As stated in a comment, the ipw2200 driver uses several routines that
were borrowed from ieee80211_geo.c. As ipw2200 requires ieee80211,
these routines are duplicated. The attached patch, which is sent
as an attachment to preserve whitespace, converts ipw2200.c to use
the ieee80211 versions, thereby reducing bloat in both the source
and binary.
Signed-Off-By: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
|
|
Fix QoS is not active even the network and the card is QOS enabled.
The problem is we pass the wrong ieee80211_network address to
ipw_handle_beacon/ipw_handle_probe_response, thus the
ieee80211_network->qos_data.active will not be set, causing the driver
not sending QoS frames at all.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Use the correct STYPE for Qos data.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The Coverity checker spotted the following bug in dup_namespace():
<-- snip -->
if (!new_ns->root) {
up_write(&namespace_sem);
kfree(new_ns);
goto out;
}
...
out:
return new_ns;
<-- snip -->
Callers expect a non-NULL result to not be freed.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
It seems that setting scheduling policy and priorities is also the kind of
thing that might be performed in apps that also use the NUMA API, so it
would seem consistent to use CAP_SYS_NICE for NUMA also.
So use CAP_SYS_NICE for controlling migration permissions.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Update the documentation for page migration.
- Fix up bits and pieces in cpusets.txt
- Rework text in vm/page-migration to be clearer and reflect the final
version of page migration in 2.6.16. Mention Andi Kleen's numactl
package that contains user space tools for page migration via
libnuma. Add reference to numa_maps and to the manpage in numactl.
- Add todo list for outstanding issues
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Acked-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
page migration currently simply retries a couple of times if try_to_unmap()
fails without inspecting the return code.
However, SWAP_FAIL indicates that the page is in a vma that has the
VM_LOCKED flag set (if ignore_refs ==1). We can check for that return code
and avoid retrying the migration.
migrate_page_remove_references() now needs to return a reason why the
failure occured. So switch migrate_page_remove_references to use -Exx
style error messages.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
It seems this patch got dropped (it was in addition to the `s390:
improve response code handling in chsc_enable_facility()' patch).
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
* git://oss.sgi.com:8090/oss/git/rc-fixes:
Fix a direct I/O locking issue revealed by the new mutex code.
|
|
Affects only XFS (i.e. DIO_OWN_LOCKING case) - currently it is
not possible to get i_mutex locking correct when using DIO_OWN
direct I/O locking in a filesystem due to indeterminism in the
possible return code/lock/unlock combinations. This can cause
a direct read to attempt a double i_mutex unlock inside XFS.
We're now ensuring __blockdev_direct_IO always exits with the
inode i_mutex (still) held for a direct reader.
Tested with the three different locking modes (via direct block
device access, ext3 and XFS) - both reading and writing; cannot
find any regressions resulting from this change, and it clearly
fixes the mutex_unlock warning originally reported here:
http://marc.theaimsgroup.com/?l=linux-kernel&m=114189068126253&w=2
Signed-off-by: Nathan Scott <nathans@sgi.com>
Acked-by: Christoph Hellwig <hch@lst.de>
|
|
This fixes a race where lsn could be cleared before taking the lock
Signed-off-by: Dave Kleikamp <shaggy@austin.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] zfcp: fix device registration issues
[SCSI] scsi_transport_fc: fix FC_HOST_NUM_ATTRS
[SCSI] scsi: aha152x pcmcia driver needs spi transport
[SCSI] zfcp: correctly set this_id for hosts
[SCSI] Add Brownie to blacklist
|
|
lapic_shutdown() re-enables interrupts which is un-desirable for panic
case, so use local_irq_save() and local_irq_restore() to keep the irqs
disabled for kexec on panic case, and close a possible race window while
kdump shutdown as shown in this stack trace
-- BUG: spinlock lockup on CPU#1, bash/4396, c52781a0
[<c01c1870>] _raw_spin_lock+0xb7/0xd2
[<c029e148>] _spin_lock+0x6/0x8
[<c011b33f>] scheduler_tick+0xe7/0x328
[<c0128a7c>] update_process_times+0x51/0x5d
[<c0114592>] smp_apic_timer_interrupt+0x4f/0x58
[<c01141ff>] lapic_shutdown+0x76/0x7e
[<c0104d7c>] apic_timer_interrupt+0x1c/0x30
[<c01141ff>] lapic_shutdown+0x76/0x7e
[<c0116659>] machine_crash_shutdown+0x83/0xaa
[<c013cc36>] crash_kexec+0xc1/0xe3
[<c029e148>] _spin_lock+0x6/0x8
[<c013cc22>] crash_kexec+0xad/0xe3
[<c0215280>] __handle_sysrq+0x84/0xfd
[<c018d937>] write_sysrq_trigger+0x2c/0x35
[<c015e47b>] vfs_write+0xa2/0x13b
[<c015ea73>] sys_write+0x3b/0x64
[<c0103c69>] syscall_call+0x7/0xb
Signed-off-by: Maneesh Soni <maneesh@in.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This reverts commit c33d4568aca9028a22857f94f5e0850012b6444b.
Andrew Clayton and Hugh Dickins report that it's broken for them and
causes strange page table and slab corruption, and spontaneous reboots.
Let's get it right next time.
Cc: Andrew Clayton <andrew@rootshell.co.uk>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
- Disable the EDAC sysfs code. The sysfs interface that EDAC presents to
user space needs more thought, and is likely to change substantially.
Therefore disable it for now so users don't start depending on it in its
current form.
- Disable the default behavior of calling panic() when an uncorrectible
error is detected (since for now, there is no sysfs interface that allows
the user to configure this behavior).
Signed-off-by: David S. Peterson <dsp@llnl.gov>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
In theory, NLM specs assure us that the server will only reply LCK_GRANTED or
LCK_DENIED_GRACE_PERIOD to our NLM_UNLOCK request.
In practice, we should not assume this to be the case, and the code will
currently Oops if we do.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
In rpc_wake_up() and rpc_wake_up_status(), it is possible for the call to
__rpc_wake_up_task() to fail if another thread happens to be calling
rpc_wake_up_task() on the same rpc_task.
Problem noticed by Bruno Faccini.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
It turns out that nfs4_proc_get_root() may return raw NFSv4 errors instead of
mapping them to kernel errors. Problem spotted by Neil Horman
<nhorman@tuxdriver.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The Coverity checker spotted this possible NULL pointer dereference in
rpc_new_client().
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Based on an original patch by Mike O'Connor and Greg Banks of SGI.
Mike states:
A normal user can panic an NFS client and cause a local DoS with
'judicious'(?) use of O_DIRECT. Any O_DIRECT write to an NFS file where the
user buffer starts with a valid mapped page and contains an unmapped page,
will crash in this way. I haven't followed the code, but O_DIRECT reads with
similar user buffers will probably also crash albeit in different ways.
Details: when nfs_get_user_pages() calls get_user_pages(), it detects and
correctly handles get_user_pages() returning an error, which happens if the
first page covered by the user buffer's address range is unmapped. However,
if the first page is mapped but some subsequent page isn't, get_user_pages()
will return a positive number which is less than the number of pages requested
(this behaviour is sort of analagous to a short write() call and appears to be
intentional). nfs_get_user_pages() doesn't detect this and hands off the
array of pages (whose last few elements are random rubbish from the newly
allocated array memory) to it's caller, whence they go to
nfs_direct_write_seg(), which then totally ignores the nr_pages it's given,
and calculates its own idea of how many pages are in the array from the user
buffer length. Needless to say, when it comes to transmit those uninitialised
page* pointers, we see a crash in the network stack.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch fixes alternate signal stack corruption among cloned threads
with CLONE_SIGHAND (and CLONE_VM) for linux-2.6.16-rc6.
The value of alternate signal stack is currently inherited after a call of
clone(... CLONE_SIGHAND | CLONE_VM). But if sigaltstack is set by a
parent thread, and then if multiple cloned child threads (+ parent threads)
call signal handler at the same time, some threads may be conflicted -
because they share to use the same alternative signal stack region.
Finally they get sigsegv. It's an undesirable race condition. Note that
child threads created from NPTL pthread_create() also hit this conflict
when the parent thread uses sigaltstack, without my patch.
To fix this problem, this patch clears the child threads' sigaltstack
information like exec(). This behavior follows the SUSv3 specification.
In SUSv3, pthread_create() says "The alternate stack shall not be inherited
(when new threads are initialized)". It means that sigaltstack should be
cleared when sigaltstack memory space is shared by cloned threads with
CLONE_SIGHAND.
Note that I chose "if (clone_flags & CLONE_SIGHAND)" line because:
- If clone_flags line is not existed, fork() does not inherit sigaltstack.
- CLONE_VM is another choice, but vfork() does not inherit sigaltstack.
- CLONE_SIGHAND implies CLONE_VM, and it looks suitable.
- CLONE_THREAD is another candidate, and includes CLONE_SIGHAND + CLONE_VM,
but this flag has a bit different semantics.
I decided to use CLONE_SIGHAND.
[ Changed to test for CLONE_VM && !CLONE_VFORK after discussion --Linus ]
Signed-off-by: GOTO Masanori <gotom@sanori.org>
Cc: Roland McGrath <roland@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: Linus Torvalds <torvalds@osdl.org>
Cc: Ulrich Drepper <drepper@redhat.com>
Cc: Jakub Jelinek <jakub@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Report AC Power present in /proc/pmu/info if there is no battery.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>,
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The behaviour of the all-in-one Video4Linux tuner driver apparently
changed. It now wants to know the tv standard, otherwise it refuses to
tune.
Restore tuning functionality in my driver for the "Multimedia eXtension
Board". The all-in-one tuner driver apparently changed its behaviour.
Signed-off-by: Michael Hunold <hunold@linuxtv.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Fix a bug in the block-erase optimization for Dataflash; it was using block
erase even for smaller segments that need page erase.
That wouldn't matter for JFFS2, which never erases less than one block
(sometimes several blocks), but for other callers it might.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
When we link a socket into the hash table, we need to make sure that we
set the num/port fields so that it shows us with a non-zero port value
in proc/netlink and on the wire. This code and comment is copied over
from the IPv4 stack as is.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
EM64T CPUs have somewhat weird error reporting for non canonical RIPs in
SYSRET.
We can't handle any exceptions there because the exception handler would
end up running on the user stack which is unsafe.
To avoid problems any code that might end up with a user touched pt_regs
should return using int_ret_from_syscall. int_ret_from_syscall ends up
using IRET, which allows safe exceptions.
Cc: Ernie Petrides <petrides@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The check is wrong and lets NULL-ptrs slip through since !IS_ERR(NULL)
is true.
Coverity #190
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When ufo_append_data fails err is uninitialized, but returned back.
Strangely gcc doesn't notice it.
Coverity #901 and #902
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Covertiy #547
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The skb given to netlink_cmsg_recv_pktinfo is already freed, move it up
a few lines.
Coverity #948
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tmp_hdr is not freed when ipv6_clear_mutable_options fails.
Coverity #650
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
