| Age | Commit message (Collapse) | Author |
|---|
|
Write ATA Feature register before ATA Sector Count register as
a preparation to use ->tf_load in ide_config_drive_speed().
This change shouldn't affect anything (just an usual paranoia).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Add ->set_irq method for setting nIEN bit of ATA Device Control
register and use it instead of ide_set_irq().
While at it:
* Use ->set_irq in init_irq() and do_reset1().
* Don't use HWIF() macro in ide_check_pm_state().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Remove ide_read_altstatus() inline helper.
* Add ->read_altstatus method for reading ATA Alternate Status
register and use it instead of ->INB.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Remove ide_read_status() inline helper.
* Add ->read_status method for reading ATA Status register
and use it instead of ->INB.
While at it:
* Don't use HWGROUP() macro.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Add ->exec_command method for writing ATA Command register
and use it instead of ->OUTBSYNC.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Factor out simplex handling from ide_pci_dma_base() to
ide_pci_check_simplex().
* Set hwif->dma_base early in ->init_dma method / ide_hwif_setup_dma()
and reset it in ide_init_port() if DMA initialization fails.
* Use ->read_sff_dma_status instead of ->INB in ide_pci_dma_base().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Export sff_dma_ops and then remove ide_setup_dma().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Use ->dma_base + offset instead of ->dma_{status,command}
and remove no longer needed ->dma_{status,command}.
While at it:
* Use ATA_DMA_* defines.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Use I/O ops directly in ide_dma_host_set(), ide_dma_setup(),
ide_dma_start() and __ide_dma_end().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Add ->read_sff_dma_status method for reading DMA Status register
and use it instead of ->INB.
While at it:
* Use inb() directly in ns87415.c::ns87415_dma_end().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Add 'hw_regs_t **hws' argument to ide_device_add[_all]() and convert
host drivers + ide_legacy_init_one() + ide_setup_pci_device[s]() to use
it instead of calling ide_init_port_hw() directly.
[ However if host has > 1 port we must still set hwif->chipset to hint
consecutive ide_find_port() call that the previous slot is occupied. ]
* Unexport ide_init_port_hw().
v2:
* Use defines instead of hard-coded values in buddha.c, gayle.c and q40ide.c.
(Suggested by Geert Uytterhoeven)
* Better patch description.
v3:
* Fix build problem in ide-cs.c. (Noticed by Stephen Rothwell)
There should be no functional changes caused by this patch.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Move ide_pci_setup_ports() call out from do_ide_setup_pci_device()
to ide_setup_pci_device[s]().
* Drop no longer needed idx argument from do_ide_setup_pci_device().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Move ide_find_port() call to pmac_ide_setup_device().
While at it:
- fix return value (s/-ENODEV/-ENOENT/)
- add DRV_NAME define and use it to set name field of pmac_port_info
- use ide_find_port_slot() instead of ide_find_port()
- remove superfluous error message (ide_find_port_slot() takes care of it)
- drop IDE interface number from driver banner message (but include bus type)
v2:
* Build fix (thanks to Stephen Rothwell for noticing the issue).
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
v2/3:
* Build fixes from Stephen Rothwell.
v4:
* Fix ->noprobe setting. (From Benjamin Herrenschmidt)
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Pass pmif instead of hwif to pmac_ide_do_{suspend,resume}().
* Store pmif instead of hwif in ->driver_data.
* Use dev_get_drvdata() instead of ->hwif_data to obtain pmif.
v2:
* Build fixes from Stephen Rothwell.
There should be no functional changes caused by this patch.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: apple_fn_keys F5 and F6
HID: remove quirk lookup from usbkbd/usbmouse
HID: Add mapping of new KEY_MEDIA_REPEAT keycode
HID: gyration remote support
HID: gyration sleep button quirk
HID: add quirk for Logitech DiNovo desktop
HID: fix quirk handling in usbmouse/kbd
HID: fix memory leak in hidraw_release
HID: add n-trig digitizer usage
HID: Invert HWHEEL mappings for some Logitech mice
HID:usbkbd:mark usb_kbd_keycode array as const
HID: add fn key support on Macbook Pro 4,1 and Macbook Air
HID: remove unused variable from hiddev compat ioctl
HID: fix compile issue in hiddev ioctl
HID: Push down BKL into ioctl handler in hidraw
HID: Switch hiddev to unlocked_ioctl
HID: use get/put_unaligned_* helpers
HID: fix report descriptor handling for MS Wireless model 1028
|
|
My copying of linux/init.h didn't go far enough. The definition of
__used singled out gcc minor version 3, but didn't care what the major
version was. This broke when unit-at-a-time was added and gcc started
throwing out initcalls.
This results in an early boot crash when ptrace tries to initialize a
process with an empty, uninitialized register set.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Removed duplicated include file <linux/smp_lock.h> in
drivers/char/nvram.c.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Since 15a647eba94c3da27ccc666bea72e7cca06b2d19 set_irq_wake returned -ENXIO
if another device had it already enabled. Zero is the right value to
return in this case. Moreover the change to desc->status was not reverted
if desc->chip->set_wake returned an error.
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add in console polling hooks for the mpsc uart for use with kgdb and
kgdboc.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
|
|
Add in console polling hooks for the cpm uart for use with kgdb and
kgdboc.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
CC: galak@kernel.crashing.org
|
|
This patch removes the old kgdb reminants from ARCH=powerpc and
implements the new style arch specific stub for the common kgdb core
interface.
It is possible to have xmon and kgdb in the same kernel, but you
cannot use both at the same time because there is only one set of
debug hooks.
The arch specific kgdb implementation saves the previous state of the
debug hooks and restores them if you unconfigure the kgdb I/O driver.
Kgdb should have no impact on a kernel that has no kgdb I/O driver
configured.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
|
|
This patch adds the ARCH=arm specific a kgdb backend, originally
written by Deepak Saxena <dsaxena@plexity.net> and George Davis
<gdavis@mvista.com>. Geoff Levand <geoffrey.levand@am.sony.com>,
Nicolas Pitre, Manish Lachwani, and Jason Wessel have contributed
various fixups here as well.
The KGDB patch makes one change to the core ARM architecture such that
the traps are initialized early for use with the debugger or other
subsystems.
[ mingo@elte.hu: small cleanups. ]
[ ben-linux@fluff.org: fixed early_trap_init ]
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Deepak Saxena <dsaxena@plexity.net>
|
|
Remove HAVE_ARCH_KGDB_SHADOW_INFO because it does not
exist anywhere in the kernel mainline sources
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
|
|
|
|
In drivers/hid/hid-input.c, the apple_fn_keys translation table
contains no entries for the F5 and F6 keys. This patch maps the F5 and
F6 keys to KBDILLUMDOWN and KBDILLUMUP, respektively, which make them
work as keyboard backlight control keys.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This patch completely removes the dependency of usbkbd and usbmouse drivers
on usbhid code.
usbkbd/usbmouse drivers are not needed in the vast majority of cases anyway,
and they shouldn't be loaded in standard configurations at all. They are supposed
to be as trivial as possible, and searching for HID_QUIRK_IGNORE can even be
bad in some cases.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This adds in a quirk for the additional un-mapped buttons on the
gyration MCE remote.
Defines are now alphabetical.
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This patch is based on one provided by Jiri Kosina to handle the sleep
button. I just added some cleanup and integrated it into my series.
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Logitech DiNovo desktop needs the same quirk as other DiNovo
devices.
Reported-by: Farid Benamrouche <farid.benamrouche@free.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
When usbmouse/kbd is set to build, USB_HID is never defined due to
the USB_HID!=y Kconfig rule. Test CONFIG_USB_HID_MODULE in both
drivers instead.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
hidraw_release() forgot to free the linked list structure, causing memory
leak.
Reported-by: Juan Marcos Diez Esteban <juan_m_diez@yahoo.es>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This adds a hid usage that is reported by the N-Trig digitizer in the Dell
Latitude XT screen.
Signed-off-by: Rafi Rubin <rafi@seas.upenn.edu>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Some Logitech mice have a tilt wheel which register as HWHEEL buttons.
The events are positive for a click to the right and negative for a
click to the left. Applications expect the opposite, though.
I suspect this affects a lot more Logitech mice, but these are the only
two I have. I tested this using evtest and a GTK application. A similar
Microsoft Intellimouse I have works correctly.
Signed-off-by: Dan Nicholson <dbn.lists@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
mark it as const because it is read only
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Added device ids to hid-quriks for detection of keyboards on 4th
generation Macbook Pro and Macbook Air
The naming scheme is consistent with past Apple keyboards in hid-quirks;
as defined by Apple (including device ids) in:
/System/Library/Extensions/AppleUSBTopCase.kext/Contents/PlugIns/AppleUSBTCKeyboard.kext/Co
ntents/Info.plist
Patch was originally posted and tested at:
https://bugs.launchpad.net/mactel-support/+bug/207127
Signed-off-by: Alexandre Karpenko <alexander@comm.utoronto.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Remove unused inode variable from hiddev compat ioctl handler.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Fix build failure introduced by Alan's ioctl -> unlocked_ioctl
(pushing BKL down to the driver) conversion patch for hiddev.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
In this case I simply wrapped it as code review suggests the locking
already terminally broken and I didn't want to make it first. See added
comment
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Push down the BKL. In some cases compat_ioctl already doesn't take the
BKL so we don't either. Some of the locking here seems already dubious
and object lifetimes want documenting
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6
|
|
Improve the PIO handling so that it can service highmem pages.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
This is alternative implementation of sg content iterator introduced
by commit 83e7d317... from Pierre Ossman in next-20080716. As there's
already an sg iterator which iterates over sg entries themselves, name
this sg_mapping_iterator.
Slightly edited description from the original implementation follows.
Iteration over a sg list is not that trivial when you take into
account that memory pages might have to be mapped before being used.
Unfortunately, that means that some parts of the kernel restrict
themselves to directly accesible memory just to not have to deal with
the mess.
This patch adds a simple iterator system that allows any code to
easily traverse an sg list and not have to deal with all the details.
The user can decide to consume part of the iteration. Also, iteration
can be stopped and resumed later if releasing the kmap between
iteration steps is necessary. These features are useful to implement
piecemeal sg copying for interrupt drive PIO for example.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Make it a bit more obvious that the card has been claimed by the
mmc_test driver so that people don't have to wonder why their block
device never shows up.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Russell no longer has the resources to fully test the controller, so
he is stepping down as maintainer.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Support highmem pages in the bounce buffer code by using the
sg_copy_from/to_buffer() functions.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Commit c8b3e02 renamed a variable, but missed one reference to it
inside a WARN_ON, causing it to incorrectly trigger.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
