| Age | Commit message (Collapse) | Author |
|---|
|
can reclaim
A bug was brought to my attention against a distro kernel but it affects
mainline and I believe problems like this have been reported in various
guises on the mailing lists although I don't have specific examples at the
moment.
The reported problem was that malloc() stalled for a long time (minutes in
some cases) if a large tmpfs mount was occupying a large percentage of
memory overall. The pages did not get cleaned or reclaimed by
zone_reclaim() because the zone_reclaim_mode was unsuitable, but the lists
are uselessly scanned frequencly making the CPU spin at near 100%.
This patchset intends to address that bug and bring the behaviour of
zone_reclaim() more in line with expectations which were noticed during
investigation. It is based on top of mmotm and takes advantage of
Kosaki's work with respect to zone_reclaim().
Patch 1 fixes the heuristics that zone_reclaim() uses to determine if the
scan should go ahead. The broken heuristic is what was causing the
malloc() stall as it uselessly scanned the LRU constantly. Currently,
zone_reclaim is assuming zone_reclaim_mode is 1 and historically it
could not deal with tmpfs pages at all. This fixes up the heuristic so
that an unnecessary scan is more likely to be correctly avoided.
Patch 2 notes that zone_reclaim() returning a failure automatically means
the zone is marked full. This is not always true. It could have
failed because the GFP mask or zone_reclaim_mode were unsuitable.
Patch 3 introduces a counter zreclaim_failed that will increment each
time the zone_reclaim scan-avoidance heuristics fail. If that
counter is rapidly increasing, then zone_reclaim_mode should be
set to 0 as a temporarily resolution and a bug reported because
the scan-avoidance heuristic is still broken.
This patch:
On NUMA machines, the administrator can configure zone_reclaim_mode that
is a more targetted form of direct reclaim. On machines with large NUMA
distances for example, a zone_reclaim_mode defaults to 1 meaning that
clean unmapped pages will be reclaimed if the zone watermarks are not
being met.
There is a heuristic that determines if the scan is worthwhile but the
problem is that the heuristic is not being properly applied and is
basically assuming zone_reclaim_mode is 1 if it is enabled. The lack of
proper detection can manfiest as high CPU usage as the LRU list is scanned
uselessly.
Historically, once enabled it was depending on NR_FILE_PAGES which may
include swapcache pages that the reclaim_mode cannot deal with. Patch
vmscan-change-the-number-of-the-unmapped-files-in-zone-reclaim.patch by
Kosaki Motohiro noted that zone_page_state(zone, NR_FILE_PAGES) included
pages that were not file-backed such as swapcache and made a calculation
based on the inactive, active and mapped files. This is far superior when
zone_reclaim==1 but if RECLAIM_SWAP is set, then NR_FILE_PAGES is a
reasonable starting figure.
This patch alters how zone_reclaim() works out how many pages it might be
able to reclaim given the current reclaim_mode. If RECLAIM_SWAP is set in
the reclaim_mode it will either consider NR_FILE_PAGES as potential
candidates or else use NR_{IN}ACTIVE}_PAGES-NR_FILE_MAPPED to discount
swapcache and other non-file-backed pages. If RECLAIM_WRITE is not set,
then NR_FILE_DIRTY number of pages are not candidates. If RECLAIM_SWAP is
not set, then NR_FILE_MAPPED are not.
[kosaki.motohiro@jp.fujitsu.com: Estimate unmapped pages minus tmpfs pages]
[fengguang.wu@intel.com: Fix underflow problem in Kosaki's estimate]
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: Rik van Riel <riel@redhat.com>
Acked-by: Christoph Lameter <cl@linux-foundation.org>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
ALLOC_WMARK_MIN, ALLOC_WMARK_LOW and ALLOC_WMARK_HIGH determin whether
pages_min, pages_low or pages_high is used as the zone watermark when
allocating the pages. Two branches in the allocator hotpath determine
which watermark to use.
This patch uses the flags as an array index into a watermark array that is
indexed with WMARK_* defines accessed via helpers. All call sites that
use zone->pages_* are updated to use the helpers for accessing the values
and the array offsets for setting.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: Christoph Lameter <cl@linux-foundation.org>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix various typos in documentation txts.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This reverts commit fafd688e4c0c34da0f3de909881117d374e4c7af.
Work is progressing to switch away from pdflush as the process backing
for flushing out dirty data. So it seems pointless to add more knobs
to control pdflush threads. The original author of the patch did not
have any specific use cases for adding the knobs, so we can easily
revert this before 2.6.30 to avoid having to maintain this API
forever.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Avoid setting less than two pages for vm_dirty_bytes: this is necessary to
avoid potential division by 0 (like the following) in get_dirty_limits().
[ 49.951610] divide error: 0000 [#1] PREEMPT SMP
[ 49.952195] last sysfs file: /sys/devices/pci0000:00/0000:00:01.1/host0/target0:0:0/0:0:0:0/block/sda/uevent
[ 49.952195] CPU 1
[ 49.952195] Modules linked in: pcspkr
[ 49.952195] Pid: 3064, comm: dd Not tainted 2.6.30-rc3 #1
[ 49.952195] RIP: 0010:[<ffffffff802d39a9>] [<ffffffff802d39a9>] get_dirty_limits+0xe9/0x2c0
[ 49.952195] RSP: 0018:ffff88001de03a98 EFLAGS: 00010202
[ 49.952195] RAX: 00000000000000c0 RBX: ffff88001de03b80 RCX: 28f5c28f5c28f5c3
[ 49.952195] RDX: 0000000000000000 RSI: 00000000000000c0 RDI: 0000000000000000
[ 49.952195] RBP: ffff88001de03ae8 R08: 0000000000000000 R09: 0000000000000000
[ 49.952195] R10: ffff88001ddda9a0 R11: 0000000000000001 R12: 0000000000000001
[ 49.952195] R13: ffff88001fbc8218 R14: ffff88001de03b70 R15: ffff88001de03b78
[ 49.952195] FS: 00007fe9a435b6f0(0000) GS:ffff8800025d9000(0000) knlGS:0000000000000000
[ 49.952195] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 49.952195] CR2: 00007fe9a39ab000 CR3: 000000001de38000 CR4: 00000000000006e0
[ 49.952195] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 49.952195] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[ 49.952195] Process dd (pid: 3064, threadinfo ffff88001de02000, task ffff88001ddda250)
[ 49.952195] Stack:
[ 49.952195] ffff88001fa0de00 ffff88001f2dbd70 ffff88001f9fe800 000080b900000000
[ 49.952195] 00000000000000c0 ffff8800027a6100 0000000000000400 ffff88001fbc8218
[ 49.952195] 0000000000000000 0000000000000600 ffff88001de03bb8 ffffffff802d3ed7
[ 49.952195] Call Trace:
[ 49.952195] [<ffffffff802d3ed7>] balance_dirty_pages_ratelimited_nr+0x1d7/0x3f0
[ 49.952195] [<ffffffff80368f8e>] ? ext3_writeback_write_end+0x9e/0x120
[ 49.952195] [<ffffffff802cc7df>] generic_file_buffered_write+0x12f/0x330
[ 49.952195] [<ffffffff802cce8d>] __generic_file_aio_write_nolock+0x26d/0x460
[ 49.952195] [<ffffffff802cda32>] ? generic_file_aio_write+0x52/0xd0
[ 49.952195] [<ffffffff802cda49>] generic_file_aio_write+0x69/0xd0
[ 49.952195] [<ffffffff80365fa6>] ext3_file_write+0x26/0xc0
[ 49.952195] [<ffffffff803034d1>] do_sync_write+0xf1/0x140
[ 49.952195] [<ffffffff80290d1a>] ? get_lock_stats+0x2a/0x60
[ 49.952195] [<ffffffff80280730>] ? autoremove_wake_function+0x0/0x40
[ 49.952195] [<ffffffff8030411b>] vfs_write+0xcb/0x190
[ 49.952195] [<ffffffff803042d0>] sys_write+0x50/0x90
[ 49.952195] [<ffffffff8022ff6b>] system_call_fastpath+0x16/0x1b
[ 49.952195] Code: 00 00 00 2b 05 09 1c 17 01 48 89 c6 49 0f af f4 48 c1 ee 02 48 89 f0 48 f7 e1 48 89 d6 31 d2 48 c1 ee 02 48 0f af 75 d0 48 89 f0 <48> f7 f7 41 8b 95 ac 01 00 00 48 89 c7 49 0f af d4 48 c1 ea 02
[ 49.952195] RIP [<ffffffff802d39a9>] get_dirty_limits+0xe9/0x2c0
[ 49.952195] RSP <ffff88001de03a98>
[ 50.096523] ---[ end trace 008d7aa02f244d7b ]---
Signed-off-by: Andrea Righi <righi.andrea@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add /proc entries to give the admin the ability to control the minimum and
maximum number of pdflush threads. This allows finer control of pdflush
on both large and small machines.
The rationale is simply one size does not fit all. Admins on large and/or
small systems may want to tune the min/max pdflush thread count to best
suit their needs. Right now the min/max is hardcoded to 2/8. While
probably a fair estimate for smaller machines, large machines with large
numbers of CPUs and large numbers of filesystems/block devices may benefit
from larger numbers of threads working on different block devices.
Even if the background flushing algorithm is radically changed, it is
still likely that multiple threads will be involved and admins would still
desire finer control on the min/max other than to have to recompile the
kernel.
The patch adds '/proc/sys/vm/nr_pdflush_threads_min' and
'/proc/sys/vm/nr_pdflush_threads_max' with r/w permissions.
The minimum value for nr_pdflush_threads_min is 1 and the maximum value is
the current value of nr_pdflush_threads_max. This minimum is required
since additional thread creation is performed in a pdflush thread itself.
The minimum value for nr_pdflush_threads_max is the current value of
nr_pdflush_threads_min and the maximum value can be 1000.
Documentation/sysctl/vm.txt is also updated.
[akpm@linux-foundation.org: fix comment, fix whitespace, use __read_mostly]
Signed-off-by: Peter W Morreale <pmorreale@novell.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Update Documentation/sysctl/vm.txt and Documentation/filesystems/proc.txt.
More specifically, the section on /proc/sys/vm in
Documentation/filesystems/proc.txt was removed and a link to
Documentation/sysctl/vm.txt added.
Most of the verbiage from proc.txt was simply moved in vm.txt, with new
addtional text for "swappiness" and "stat_interval".
Signed-off-by: Peter W Morreale <pmorreale@novell.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
NOMMU mmap allocates a piece of memory for an mmap that's rounded up in size to
the nearest power-of-2 number of pages. Currently it then discards the excess
pages back to the page allocator, making that memory available for use by other
things. This can, however, cause greater amount of fragmentation.
To counter this, a sysctl is added in order to fine-tune the trimming
behaviour. The default behaviour remains to trim pages aggressively, while
this can either be disabled completely or set to a higher page-granular
watermark in order to have finer-grained control.
vm region vm_top bits taken from an earlier patch by David Howells.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Mike Frysinger <vapier.adi@gmail.com>
|
|
This change introduces two new sysctls to /proc/sys/vm:
dirty_background_bytes and dirty_bytes.
dirty_background_bytes is the counterpart to dirty_background_ratio and
dirty_bytes is the counterpart to dirty_ratio.
With growing memory capacities of individual machines, it's no longer
sufficient to specify dirty thresholds as a percentage of the amount of
dirtyable memory over the entire system.
dirty_background_bytes and dirty_bytes specify quantities of memory, in
bytes, that represent the dirty limits for the entire system. If either
of these values is set, its value represents the amount of dirty memory
that is needed to commence either background or direct writeback.
When a `bytes' or `ratio' file is written, its counterpart becomes a
function of the written value. For example, if dirty_bytes is written to
be 8096, 8K of memory is required to commence direct writeback.
dirty_ratio is then functionally equivalent to 8K / the amount of
dirtyable memory:
dirtyable_memory = free pages + mapped pages + file cache
dirty_background_bytes = dirty_background_ratio * dirtyable_memory
-or-
dirty_background_ratio = dirty_background_bytes / dirtyable_memory
AND
dirty_bytes = dirty_ratio * dirtyable_memory
-or-
dirty_ratio = dirty_bytes / dirtyable_memory
Only one of dirty_background_bytes and dirty_background_ratio may be
specified at a time, and only one of dirty_bytes and dirty_ratio may be
specified. When one sysctl is written, the other appears as 0 when read.
The `bytes' files operate on a page size granularity since dirty limits
are compared with ZVC values, which are in page units.
Prior to this change, the minimum dirty_ratio was 5 as implemented by
get_dirty_limits() although /proc/sys/vm/dirty_ratio would show any user
written value between 0 and 100. This restriction is maintained, but
dirty_bytes has a lower limit of only one page.
Also prior to this change, the dirty_background_ratio could not equal or
exceed dirty_ratio. This restriction is maintained in addition to
restricting dirty_background_bytes. If either background threshold equals
or exceeds that of the dirty threshold, it is implicitly set to half the
dirty threshold.
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Andrea Righi <righi.andrea@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
corrections.
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Adds a new sysctl, 'oom_dump_tasks', that enables the kernel to produce a
dump of all system tasks (excluding kernel threads) when performing an
OOM-killing. Information includes pid, uid, tgid, vm size, rss, cpu,
oom_adj score, and name.
This is helpful for determining why there was an OOM condition and which
rogue task caused it.
It is configurable so that large systems, such as those with several
thousand tasks, do not incur a performance penalty associated with dumping
data they may not desire.
If an OOM was triggered as a result of a memory controller, the tasklist
shall be filtered to exclude tasks that are not a member of the same
cgroup.
Cc: Andrea Arcangeli <andrea@suse.de>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add vm.highmem_is_dirtyable toggle
A 32 bit machine with HIGHMEM64 enabled running DCC has an MMAPed file of
approximately 2Gb size which contains a hash format that is written
randomly by the dbclean process. On 2.6.16 this process took a few
minutes. With lowmem only accounting of dirty ratios, this takes about 12
hours of 100% disk IO, all random writes.
Include a toggle in /proc/sys/vm/highmem_is_dirtyable which can be set to 1 to
add the highmem back to the total available memory count.
[akpm@linux-foundation.org: Fix the CONFIG_DETECT_SOFTLOCKUP=y build]
Signed-off-by: Bron Gondwana <brong@fastmail.fm>
Cc: Ethan Solomita <solo@google.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: WU Fengguang <wfg@mail.ustc.edu.cn>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The hugetlb documentation has gotten a bit out of sync with the current code.
Updated the sysctl file to refer to Documentation/vm/hugetlbpage.txt. Update
that file to contain the current state of affairs (with the newer named sysctl
in place).
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Acked-by: Adam Litke <agl@us.ibm.com>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
min_free_pages is critical for correctness, document it as such.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Adds a new sysctl, 'oom_kill_allocating_task', which will automatically kill
the OOM-triggering task instead of scanning through the tasklist to find a
memory-hogging target. This is helpful for systems with an insanely large
number of tasks where scanning the tasklist significantly degrades
performance.
Cc: Andrea Arcangeli <andrea@suse.de>
Acked-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch adds the kernelcore= parameter for x86.
Once all patches are applied, a new command-line parameter exist and a new
sysctl. This patch adds the necessary documentation.
From: Yasunori Goto <y-goto@jp.fujitsu.com>
When "kernelcore" boot option is specified, kernel can't boot up on ia64
because of an infinite loop. In addition, the parsing code can be handled
in an architecture-independent manner.
This patch uses common code to handle the kernelcore= parameter. It is
only available to architectures that support arch-independent zone-sizing
(i.e. define CONFIG_ARCH_POPULATES_NODE_MAP). Other architectures will
ignore the boot parameter.
[bunk@stusta.de: make cmdline_parse_kernelcore() static]
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Acked-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Make zonelist creation policy selectable from sysctl/boot option v6.
This patch makes NUMA's zonelist (of pgdat) order selectable.
Available order are Default(automatic)/ Node-based / Zone-based.
[Default Order]
The kernel selects Node-based or Zone-based order automatically.
[Node-based Order]
This policy treats the locality of memory as the most important parameter.
Zonelist order is created by each zone's locality. This means lower zones
(ex. ZONE_DMA) can be used before higher zone (ex. ZONE_NORMAL) exhausion.
IOW. ZONE_DMA will be in the middle of zonelist.
current 2.6.21 kernel uses this.
Pros.
* A user can expect local memory as much as possible.
Cons.
* lower zone will be exhansted before higher zone. This may cause OOM_KILL.
Maybe suitable if ZONE_DMA is relatively big and you never see OOM_KILL
because of ZONE_DMA exhaution and you need the best locality.
(example)
assume 2 node NUMA. node(0) has ZONE_DMA/ZONE_NORMAL, node(1) has ZONE_NORMAL.
*node(0)'s memory allocation order:
node(0)'s NORMAL -> node(0)'s DMA -> node(1)'s NORMAL.
*node(1)'s memory allocation order:
node(1)'s NORMAL -> node(0)'s NORMAL -> node(0)'s DMA.
[Zone-based order]
This policy treats the zone type as the most important parameter.
Zonelist order is created by zone-type order. This means lower zone
never be used bofere higher zone exhaustion.
IOW. ZONE_DMA will be always at the tail of zonelist.
Pros.
* OOM_KILL(bacause of lower zone) occurs only if the whole zones are exhausted.
Cons.
* memory locality may not be best.
(example)
assume 2 node NUMA. node(0) has ZONE_DMA/ZONE_NORMAL, node(1) has ZONE_NORMAL.
*node(0)'s memory allocation order:
node(0)'s NORMAL -> node(1)'s NORMAL -> node(0)'s DMA.
*node(1)'s memory allocation order:
node(1)'s NORMAL -> node(0)'s NORMAL -> node(0)'s DMA.
bootoption "numa_zonelist_order=" and proc/sysctl is supporetd.
command:
%echo N > /proc/sys/vm/numa_zonelist_order
Will rebuild zonelist in Node-based order.
command:
%echo Z > /proc/sys/vm/numa_zonelist_order
Will rebuild zonelist in Zone-based order.
Thanks to Lee Schermerhorn, he gives me much help and codes.
[Lee.Schermerhorn@hp.com: add check_highest_zone to build_zonelists_in_zone_order]
[akpm@linux-foundation.org: build fix]
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Andi Kleen <ak@suse.de>
Cc: "jesse.barnes@intel.com" <jesse.barnes@intel.com>
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add a new security check on mmap operations to see if the user is attempting
to mmap to low area of the address space. The amount of space protected is
indicated by the new proc tunable /proc/sys/vm/mmap_min_addr and defaults to
0, preserving existing behavior.
This patch uses a new SELinux security class "memprotect." Policy already
contains a number of allow rules like a_t self:process * (unconfined_t being
one of them) which mean that putting this check in the process class (its
best current fit) would make it useless as all user processes, which we also
want to protect against, would be allowed. By taking the memprotect name of
the new class it will also make it possible for us to move some of the other
memory protect permissions out of 'process' and into the new class next time
we bump the policy version number (which I also think is a good future idea)
Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
|
|
The current panic_on_oom may not work if there is a process using
cpusets/mempolicy, because other nodes' memory may remain. But some people
want failover by panic ASAP even if they are used. This patch makes new
setting for its request.
This is tested on my ia64 box which has 3 nodes.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Paul Jackson <pj@sgi.com>
Cc: Ethan Solomita <solo@google.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch fixes typos in various Documentation txts. The patch addresses some
misc words.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Currently one can enable slab reclaim by setting an explicit option in
/proc/sys/vm/zone_reclaim_mode. Slab reclaim is then used as a final
option if the freeing of unmapped file backed pages is not enough to free
enough pages to allow a local allocation.
However, that means that the slab can grow excessively and that most memory
of a node may be used by slabs. We have had a case where a machine with
46GB of memory was using 40-42GB for slab. Zone reclaim was effective in
dealing with pagecache pages. However, slab reclaim was only done during
global reclaim (which is a bit rare on NUMA systems).
This patch implements slab reclaim during zone reclaim. Zone reclaim
occurs if there is a danger of an off node allocation. At that point we
1. Shrink the per node page cache if the number of pagecache
pages is more than min_unmapped_ratio percent of pages in a zone.
2. Shrink the slab cache if the number of the nodes reclaimable slab pages
(patch depends on earlier one that implements that counter)
are more than min_slab_ratio (a new /proc/sys/vm tunable).
The shrinking of the slab cache is a bit problematic since it is not node
specific. So we simply calculate what point in the slab we want to reach
(current per node slab use minus the number of pages that neeed to be
allocated) and then repeately run the global reclaim until that is
unsuccessful or we have reached the limit. I hope we will have zone based
slab reclaim at some point which will make that easier.
The default for the min_slab_ratio is 5%
Also remove the slab option from /proc/sys/vm/zone_reclaim_mode.
[akpm@osdl.org: cleanups]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
It turns out that it is advantageous to leave a small portion of unmapped file
backed pages if all of a zone's pages (or almost all pages) are allocated and
so the page allocator has to go off-node.
This allows recently used file I/O buffers to stay on the node and
reduces the times that zone reclaim is invoked if file I/O occurs
when we run out of memory in a zone.
The problem is that zone reclaim runs too frequently when the page cache is
used for file I/O (read write and therefore unmapped pages!) alone and we have
almost all pages of the zone allocated. Zone reclaim may remove 32 unmapped
pages. File I/O will use these pages for the next read/write requests and the
unmapped pages increase. After the zone has filled up again zone reclaim will
remove it again after only 32 pages. This cycle is too inefficient and there
are potentially too many zone reclaim cycles.
With the 1% boundary we may still remove all unmapped pages for file I/O in
zone reclaim pass. However. it will take a large number of read and writes
to get back to 1% again where we trigger zone reclaim again.
The zone reclaim 2.6.16/17 does not show this behavior because we have a 30
second timeout.
[akpm@osdl.org: rename the /proc file and the variable]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
/proc/sys/vm/zone_reclaim_interval
The zone_reclaim_interval was necessary because we were not able to determine
how many unmapped pages exist in a zone. Therefore we had to scan in
intervals to figure out if any pages were unmapped.
With the zoned counters and NR_ANON_PAGES we now know the number of pagecache
pages and the number of mapped pages in a zone. So we can simply skip the
reclaim if there is an insufficient number of unmapped pages. We use
SWAP_CLUSTER_MAX as the boundary.
Drop all support for /proc/sys/vm/zone_reclaim_interval.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch adds panic_on_oom sysctl under sys.vm.
When sysctl vm.panic_on_oom = 1, the kernel panics intead of killing rogue
processes. And if vm.panic_on_oom is 0 the kernel will do oom_kill() in
the same way as it does today. Of course, the default value is 0 and only
root can modifies it.
In general, oom_killer works well and kill rogue processes. So the whole
system can survive. But there are environments where panic is preferable
rather than kill some processes.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
If large amounts of zone memory are used by empty slabs then zone_reclaim
becomes uneffective. This patch shakes the slab a bit.
The problem with this patch is that the slab reclaim is not containable to a
zone. Thus slab reclaim may affect the whole system and be extremely slow.
This also means that we cannot determine how many pages were freed in this
zone. Thus we need to go off node for at least one allocation.
The functionality is disabled by default.
We could modify the shrinkers to take a zone parameter but that would be quite
invasive. Better ideas are welcome.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
In some situations one may want zone_reclaim to behave differently. For
example a process writing large amounts of memory will spew unto other nodes
to cache the writes if many pages in a zone become dirty. This may impact the
performance of processes running on other nodes.
Allowing writes during reclaim puts a stop to that behavior and throttles the
process by restricting the pages to the local zone.
Similarly one may want to contain processes to local memory by enabling
regular swap behavior during zone_reclaim. Off node memory allocation can
then be controlled through memory policies and cpusets.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Currently the zone_reclaim code has a fixed window of 30 seconds of off node
allocations should a local zone have no unused pagecache pages left. Reclaim
will be attempted again after this timeout period to avoid repeated useless
scans for memory. This is also useful to established sufficiently large off
node allocation chunks to relieve the local node.
It may be beneficial to adjust that time period for some special situations.
For example if memory use was exceeding node capacity one may want to give up
for longer periods of time. If memory spikes intermittendly then one may want
to shorten the time period to reduce the number of off node allocations.
This patch allows just that....
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
proc support for zone reclaim
This patch creates a proc entry /proc/sys/vm/zone_reclaim_mode that may be
used to override the automatic determination of the zone reclaim made on
bootup.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
As recently there has been lot of traffic on the right values for batch and
high water marks for per_cpu_pagelists. This patch makes these two
variables configurable through /proc interface.
A new tunable /proc/sys/vm/percpu_pagelist_fraction is added. This entry
controls the fraction of pages at most in each zone that are allocated for
each per cpu page list. The min value for this is 8. It means that we
don't allow more than 1/8th of pages in each zone to be allocated in any
single per_cpu_pagelist.
The batch value of each per cpu pagelist is also updated as a result. It
is set to pcp->high/4. The upper limit of batch is (PAGE_SHIFT * 8)
Signed-off-by: Rohit Seth <rohit.seth@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Add /proc/sys/vm/drop_caches. When written to, this will cause the kernel to
discard as much pagecache and/or reclaimable slab objects as it can. THis
operation requires root permissions.
It won't drop dirty data, so the user should run `sync' first.
Caveats:
a) Holds inode_lock for exorbitant amounts of time.
b) Needs to be taught about NUMA nodes: propagate these all the way through
so the discarding can be controlled on a per-node basis.
This is a debugging feature: useful for getting consistent results between
filesystem benchmarks. We could possibly put it under a config option, but
it's less than 300 bytes.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
|
