aboutsummaryrefslogtreecommitdiff
path: root/arch/arm/mach-omap2/board-omap3beagle.c
AgeCommit message (Collapse)Author
2010-02-19omap: musb: Pass board specific data from board fileMaulik Mankad
Pass board specific data for MUSB (like interface_type, mode etc) from board file by defining board specific structure. Each board file can define this structure based on its requirement and pass this information to the driver. Signed-off-by: Maulik Mankad <x0082077@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Felipe Balbi <felipe.balbi@nokia.com> Cc: David Brownell <david-b@pacbell.net> Cc: Greg Kroah-Hartman <gregkh@suse.de> Cc: Gupta Ajay Kumar <ajay.gupta@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-02-15omap: Rename hsmmc symbols to reflect independence from twl4030Adrian Hunter
hsmmc.[ch] no longer has any dependency on twl4030 and variable names should be renamed to reflect that. Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-02-15omap: Rename mmc-twl4030 files to hsmmcAdrian Hunter
mmc-twl4030.[ch] no longer has any dependency on twl4030 and should be renamed to reflect that. Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-02-15omap2/3/4: Fix omap2_map_common_io for multi-omapTony Lindgren
Fix omap2_map_common_io for multi-omap Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-12-13mfd: Rename twl4030* driver files to enable re-useSantosh Shilimkar
The upcoming TWL6030 is companion chip for OMAP4 like the current TWL4030 for OMAP3. The common modules like RTC, Regulator creates opportunity to re-use the most of the code from twl4030. This patch renames few common drivers twl4030* files to twl* to enable the code re-use. Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Balaji T K <balajitk@ti.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Acked-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2009-12-11omap: mux: Remove old mux code for 34xxTony Lindgren
Remove old mux code for 34xx Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-12-11omap: mux: Replace omap_cfg_reg() with new style signal or gpio functionsTony Lindgren
Replace omap_cfg_reg() with new style signal or gpio functions Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-12-11omap: mux: Add new style init functions to omap3 board-*.c filesTony Lindgren
Add new style mux init functions to omap3 board-*.c files So far Beagle has been confirmed to be a CBB package, and CM-T35 a CUS package. Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-11-22omap: Add platform init code for EHCI driverFelipe Balbi
Add platform init code for EHCI driver. Various fixes to the original patch by Ajay Kumar Gupta <ajay.gupta@ti.com> and Anand Gadiyar <gadiyar@ti.com>. Overo support added by Olof Johansson <olof@lixom.net> Beagle support added by Koen Kooi <koen@beagleboard.org> CM-T32 support added by Mike Rapoport <mike@compulab.co.il> Signed-off-by: Signed-off-by: Olof Johansson <olof@lixom.net> Acked-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Koen Kooi <koen@beagleboard.org> Signed-off-by: Mike Rapoport <mike@compulab.co.il> Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com> Signed-off-by: Anand Gadiyar <gadiyar@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-11-22OMAP: Configure audio_mclk for twl4030-codec MFDPeter Ujfalusi
audio_mclk value is going to be handled by the twl4030-codec MFD driver, configure the correct value for boards, which is using the twl4030 audio. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-11-22OMAP: Platform support for twl4030_codec MFDPeter Ujfalusi
Add needed platform data for the twl4030_codec MFD on boards, where the audio part of the twl4030 codec is used. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-11-22Merge 7xx-iosplit-plat-merge with omap-fixesTony Lindgren
Merge branch '7xx-iosplit-plat-merge' into omap-for-linus
2009-11-11omap3: beagle: Fix USB host port power controlJarkko Nikula
The host port power is enabled by driving the nEN_USB_PWR low as stated in the comment. This fix is originally from Steve Sakoman <steve@sakoman.com>. Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Cc: Steve Sakoman <steve@sakoman.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-10-20omap: headers: Move remaining headers from include/mach to include/platTony Lindgren
Move the remaining headers under plat-omap/include/mach to plat-omap/include/plat. Also search and replace the files using these headers to include using the right path. This was done with: #!/bin/bash mach_dir_old="arch/arm/plat-omap/include/mach" plat_dir_new="arch/arm/plat-omap/include/plat" headers=$(cd $mach_dir_old && ls *.h) omap_dirs="arch/arm/*omap*/ \ drivers/video/omap \ sound/soc/omap" other_files="drivers/leds/leds-ams-delta.c \ drivers/mfd/menelaus.c \ drivers/mfd/twl4030-core.c \ drivers/mtd/nand/ams-delta.c" for header in $headers; do old="#include <mach\/$header" new="#include <plat\/$header" for dir in $omap_dirs; do find $dir -type f -name \*.[chS] | \ xargs sed -i "s/$old/$new/" done find drivers/ -type f -name \*omap*.[chS] | \ xargs sed -i "s/$old/$new/" for file in $other_files; do sed -i "s/$old/$new/" $file done done for header in $(ls $mach_dir_old/*.h); do git mv $header $plat_dir_new/ done Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-10-19omap: Fix DEBUG_LL UART io addressSantosh Shilimkar
This patch fixes the low level debug UART io address as per this series. The change is essential to have CONFIG_DEBUG_LL working. Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-09-24omap: Fix MMC gpio_wp for BeagleBoard C2 and aboveJarkko Nikula
Earlier BeagleBoards were using pad AH8 muxed to GPIO29 for MMC write-protect. However, this signal has been changed to pad AG9 in board revision C2. Fix this by adding mux configuration for pad AG9, runtime check for board revisions and set the gpio number and pad muxing accordingly. Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-09-03OMAP2/3 board-*.c files: read bootloader configuration earlierPaul Walmsley
Most board-*.c files read configuration data from the bootloader in their .init_machine() function. This needs to happen earlier, at some point before omap2_init_common_hw() is called. This is because a future patch will use the bootloader serial console port information to enable the UART clocks earlier, immediately after omap2_clk_init(). This is in turn necessary since otherwise clock tree usecounts on clocks like dpll4_m2x2_ck will be bogus, which can cause the currently-active console UART clock to be disabled during boot. Signed-off-by: Paul Walmsley <paul@pwsan.com>
2009-08-28OMAP3: beagle: add missing twl4030 usb platform_dataFelipe Balbi
without it twl4030_usb driver will not probe. Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-08-28OMAP: UART: drop OMAP_TAG_UART, enable all UARTs, auto-disabled on idleKalle Valo
OMAP tags are deprecrated so drop them. Drop UART config data which decides which UARTs to enable during boot. This is no longer necessary since serial core code disables clocks after inactivity. Background: with new UART idle code, all on-chip UARTs are idled using a configurable inactivity timer (default 5 seconds.) After the inactivity timer, UART clocks are disabled automatically. Signed-off-by: Kalle Valo <kalle.valo@iki.fi> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-07-24OMAP3: Setup MUX settings for SDRC CKE signalsJean Pihet
This patches ensures the MUX settings are correct for the SDRC CKE signals to SDRAM. This allows the self-refresh to work when 2 chip-selects are in use. A warning is thrown away in case the initial muxing is incorrect, in order to track faulty or old-dated bootloaders. Note: The CONFIG_OMAP_MUX and CONFIG_OMAP_MUX_WARNINGS options must be enabled for the mux code to have effect. Signed-off-by: Jean Pihet <jpihet@mvista.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
2009-07-24OMAP3 SDRC: add support for 2 SDRAM chip selectsJean Pihet
Some OMAP3 boards (Beagle Cx, Overo, RX51, Pandora) have 2 SDRAM parts connected to the SDRC. This patch adds the following: - add a new argument of type omap_sdrc_params struct* to omap2_init_common_hw and omap2_sdrc_init for the 2nd CS params - adapted the OMAP boards files to the new prototype of omap2_init_common_hw - add the SDRC 2nd CS registers offsets defines - adapt the sram sleep code to configure the SDRC for the 2nd CS Note: If the 2nd param to omap2_init_common_hw is NULL, then the parameters are not programmed into the SDRC CS1 registers Tested on 3430 SDP and Beagleboard rev C2 and B5, with suspend/resume and frequency changes (cpufreq). Signed-off-by: Jean Pihet <jpihet@mvista.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
2009-05-28ARM: OMAP3: Initialize regulators for Beagle and OveroDavid Brownell
Initialize regulators for Beagle and Overo. Patch is based on earlier patches posted to linux-omap mailing list. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-05-28ARM: OMAP3: SDRC: add timing data for Micron MT46H32M32LF-6, v2Paul Walmsley
Add timing data for the Micron MT46H32M32LF-6 SDRAM chip, used on the OMAP3 Beagle and EVM boards. Original timing data is from the Micron datasheet PDF downloaded from: http://download.micron.com/pdf/datasheets/dram/mobile/1gb_ddr_mobile_sdram_t48m.pdf Thanks to Rajendra Nayak <rnayak@ti.com> for his help identifying the chips used on Beagle & OMAP3EVM. Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-04-23OMAP2/3 GPTIMER: allow system tick GPTIMER to be changed in board-*.c filesPaul Walmsley
Add a function omap2_gp_clockevent_set_gptimer() for board-*.c files to use in .init_irq functions to configure the system tick GPTIMER. Practical choices at this point are GPTIMER1 or GPTIMER12. Both of these timers are in the WKUP powerdomain, and so are unaffected by chip power management. GPTIMER1 can use sys_clk as a source, for applications where a high-resolution timer is more important than power management. GPTIMER12 has the special property that it has the secure 32kHz oscillator as its source clock, which may be less prone to glitches than the off-chip 32kHz oscillator. But on HS devices, it may not be available for Linux use. It appears that most boards are fine with GPTIMER1, but BeagleBoard should use GPTIMER12 when using a 32KiHz timer source, due to hardware bugs in revisions B4 and below. Modify board-omap3beagle.c to use GPTIMER12. This patch originally used a Kbuild config option to select the GPTIMER, but was changed to allow this to be specified in board-*.c files, per Tony's request. Kalle Vallo <kalle.valo@nokia.com> found a bug in an earlier version of this patch - thanks Kalle. Tested on Beagle rev B4 ES2.1, with and without CONFIG_OMAP_32K_TIMER, and 3430SDP. Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Cc: Kalle Valo <kalle.valo@nokia.com>
2009-03-25Merge branch 'for-next' of ↵Russell King
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6 into devel
2009-03-23ARM: OMAP3: MUSB initialization for omap hw, v2Felipe Balbi
Create a generic board-file for initializing usb on omap2430 and omap3 boards. Patch modified by Tony to build the module based on CONFIG_USB_MUSB_SOC. Also merged in a patch adding the nop xceiv from Ajay Kumar Gupta <ajay.gupta@ti.com>. Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-03-23ARM: OMAP3: Remove unused CONFIG_I2C2_OMAP_BEAGLEJarkko Nikula
There is no CONFIG_I2C2_OMAP_BEAGLE in mainline and it is under removal in linux-omap also so remove this dead code now. Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-03-19Merge branch 'master' of git://git.marvell.com/orion into develRussell King
Conflicts: arch/arm/mach-mx1/devices.c
2009-03-04ARM: OMAP: board-omap3beagle: set i2c-3 to 100kHzKoen Kooi
Changing it do 100kHz is needed to make more devices works properly. Controlling the TI DLP Pico projector[1] doesn't work properly at 400kHz, 100kHz and lower work fine. EDID readout is unaffected by this change. [1] http://focus.ti.com/dlpdmd/docs/dlpdiscovery.tsp?sectionId=60&tabId=2234 Signed-off-by: Koen Kooi <koen@beagleboard.org> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-02-08[ARM] OMAP2 SDRC: add SDRAM timing parameter infrastructurePaul Walmsley
For a given SDRAM clock rate, SDRAM chips require memory controllers to use a specific set of timing minimums and maximums to transfer data reliably. These parameters can be different for different memory chips and can also potentially vary by board. This patch adds the infrastructure for board-*.c files to pass this timing data to the SDRAM controller init function. The timing data is specified in an 'omap_sdrc_params' structure, in terms of SDRC controller register values. An array of these structs, one per SDRC target clock rate, is passed by the board-*.c file to omap2_init_common_hw(). This patch does not define the values for different memory chips, nor does it use the values for anything; those will come in subsequent patches. linux-omap source commit is bc84ecfc795c2d1c5cda8da4127cf972f488a696. Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-01-15ARM: OMAP: Fix compile for beagleTony Lindgren
Move twl4030 gpio init code to where it should be. Also include twl4030.h. Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-12-10omap mmc: Add low-level initialization for hsmmc controllerTony Lindgren
Add low-level initialization for hsmmc controller. Merged into this patch patch are various improvments and board support by Grazvydas Ignotas and David Brownell. Also change wire4 to be wires, as some newer controllers support 8 data lines. Cc: Pierre Ossman <drzeus-mmc@drzeus.cx> Signed-off-by: Grazvydas Ignotas <notasas@gmail.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-10-09ARM: OMAP3: Add minimal Beagle board supportSyed Mohammed, Khasim
Add minimal Beagle board support. Based on earlier patches by Syed Mohammed Khasim with some fixes from linux-omap tree. Signed-off-by: Syed Mohammed Khasim <khasim@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-29 06:26:33 +0000