| Age | Commit message (Collapse) | Author |
|---|
|
Commit f62349ee9788b1d94c55eb6c291d74a1f69bdd9e had side effect that
causes kernel to oops when we are suspending to ram:
# echo mem > /sys/power/state
WARNING: at kernel/irq/manage.c:858 __free_irq+0x90/0x174()
Trying to free already-free IRQ 72
Modules linked in:
Backtrace:
[<c00328d0>] (dump_backtrace+0x0/0x110) from [<c0347298>] (dump_stack+0x18/0x1c)
r7:dfd4be08 r6:c009505c r5:c03fbfd1 r4:0000035a
[<c0347280>] (dump_stack+0x0/0x1c) from [<c005a408>] (warn_slowpath_common+0x50/0x68)
[<c005a3b8>] (warn_slowpath_common+0x0/0x68) from [<c005a46c>] (warn_slowpath_fmt+0x30)
r7:c0474afc r6:00000048 r5:00000000 r4:c0474ac0
[<c005a43c>] (warn_slowpath_fmt+0x0/0x38) from [<c009505c>] (__free_irq+0x90/0x174)
r3:00000048 r2:c03fc0ef
[<c0094fcc>] (__free_irq+0x0/0x174) from [<c0095184>] (free_irq+0x44/0x64)
[<c0095140>] (free_irq+0x0/0x64) from [<c0038100>] (omap_uart_enable_irqs+0x4c/0x90)
r7:c034d58c r6:00000003 r5:00000000 r4:c0463028
[<c00380b4>] (omap_uart_enable_irqs+0x0/0x90) from [<c003d8f8>] (omap3_pm_begin+0x1c/0)
r5:00000003 r4:00000000
[<c003d8dc>] (omap3_pm_begin+0x0/0x28) from [<c008d008>] (suspend_devices_and_enter+0x)
[<c008cfd8>] (suspend_devices_and_enter+0x0/0x1dc) from [<c008d29c>] (enter_state+0xe8)
r5:c03f7f46 r4:00000000
[<c008d1b4>] (enter_state+0x0/0x140) from [<c008c8e0>] (state_store+0x9c/0xc4)
r7:c034d58c r6:00000003 r5:00000003 r4:c03f7f46
[<c008c844>] (state_store+0x0/0xc4) from [<c01cb2dc>] (kobj_attr_store+0x20/0x24)
[<c01cb2bc>] (kobj_attr_store+0x0/0x24) from [<c0119420>] (sysfs_write_file+0x114/0x14)
[<c011930c>] (sysfs_write_file+0x0/0x148) from [<c00cb298>] (vfs_write+0xb8/0x164)
[<c00cb1e0>] (vfs_write+0x0/0x164) from [<c00cb408>] (sys_write+0x44/0x70)
r8:4001f000 r7:00000004 r6:df81bd00 r5:00000000 r4:00000000
[<c00cb3c4>] (sys_write+0x0/0x70) from [<c002f040>] (ret_fast_syscall+0x0/0x38)
r8:c002f204 r7:00000004 r6:401fa5e8 r5:4001f000 r4:00000004
This is due the fact that uart_list list was populated in
omap_serial_early_init() and omap_uart_enable_irqs() went through this
list even when serial idle wasn't enabled for all uarts.
This patch moves the code that populates the uart_list and enables uart
clocks into omap_serial_init_port().
Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Recent drivers/mfd/twl4030* renames to twl broke compile for
various boards as the series was missing a patch to change
the board-*.c files.
This patch renames include twl4030.h to include twl.h
and also renames twl4030_i2c_ routines.
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
OMAP34XX has EHCI, so select USB_ARCH_HAS_EHCI.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The upcoming TWL6030 is companion chip for OMAP4 like the current TWL4030
for OMAP3. The common modules like RTC, Regulator creates opportunity
to re-use the most of the code from twl4030.
This patch renames few common drivers twl4030* files to twl* to enable
the code re-use.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The power scripts optimisation was mainly done by:
Tero Kristo <tero.kristo@nokia.com> and
Arnaud Mandy <ext-arnaud.2.mandy@nokia.com>
I'm only refactoring and testing it against the mainline kernel.
Signed-off-by: Amit Kucheria <amit.kucheria@verdurent.com>
Cc: Tero Kristo <tero.kristo@nokia.com>
Cc: linux-omap@vger.kernel.org
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
OMAP3xxx and OMAP4430 UART IP blocks have a restriction wrt RX FIFO.
Empty RX fifo read causes an abort.
OMAP3xxx:
UART IP revision >= 0x52 have this issue
MVR register format is:
Bits Field Name Description Type Reset
31:8 RESERVED RO 0x0
7:4 MAJOR Major revision number of the module. RO 0x--
3:0 MINOR Minor revision number of the module. RO 0x--
OMAP4xxx:
All revisions have this issue
Revision id check is not used as the format of MVR resigster has changed
For omap4 MVR register reads as: 0x50410602 => Revision id = 0x0602
Format of MVR register on omap4 is: (Courtesy: Cousson, Benoit)
Bits Field Name Description Type Reset
31:30 SCHEME Scheme revision number of module RO 0x1
29:28 RESERVED RO 0x1
27:16 FUNC Function revision number of module RO 0x041
15:11 RTL Rtl revision number of module RO 0x00
10:8 MAJOR Major revision number of the module. RO 0x6
7:6 CUSTOM Custom revision number of the module. RO 0x0
5:0 MINOR Minor revision number of the module. RO 0x02
Override the default 8250 read handler: mem_serial_in()
by a custom handler: serial_in_8250()
which makes sure that RX fifo is not read when empty
tested on zoom3(3630) board
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Update the hsmmc zoom peripheral configuration to support:
Power saving mode
mmc2 8-bit support
Configure mmc2 as non removable
Signed-off-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The runtime detection of OMAP3515 and OMAP3525
was reversed.
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Otherwise Extreme Lower Power (ELP) wakeup doesn't work properly.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
omap3: zoom2/3: make MMC slot work again
Commit 12f8dfb56 accidentally broke MMC on zoom2/3.
The .vmmc1 field of zoom_twldata was deleted. Restoring it
allows the MMC slot to work again
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch adds new function: omap_serial_init_port(port) that can be
used to initialize only selected UARTs as serial ports. Platforms can
then in their board files call this function instead of omap_serial_init()
if they don't want to use all UARTs as serial ports.
Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
CM-T35 can be assembled with different set of peripherals thus making
certain interfaces available to user as GPIOs or dedicated pins. Because
of it CM-T35 bootloader sets up mux configuration only for pins
necessary to boot the system and the rest of the mux configuration is
done by the kernel. Besides, having mux configuration in the kernel
allows to minimize dependancy on bootloader.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The secondary cores wakes up in time so the wait loop is not
necessary anymore.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The AuxCoreBoot0 and AuxCoreBoot1 can be only accessed in secure
mode. Replace the current code with secure monitor API's to access/modify
these registers.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch fixes the OMAP4430 cpu detection. The IC rev detection is
done with hawkeye and rev. Note that rev does not map directly to
defined processor revision numbers as ES1.0 uses value 0.It also fixes
the SCM base address to read the correct ID_CODE register.
Also the cpu_is_omap44xx() and cpu_is_omap443x() correctly populated
instead of always being true
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Pandora board file updates:
- change keycodes of game buttons
it was decided not to use ABXY layout by the developers.
- drop i2c bus 3 speed to 100kHz
this is needed for battery monitoring chip to work reliably.
- drop pandora_lcd platform_device
the older DSS driver was never functional on l-o or mainline
kernels due to missing panel driver, so remove unneeded
pandora_lcd platform_device. This also removes last OMAP_TAG
from the board file.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Board file of Always Innovating OMAP3-based Touch Book
Signed-off-by: Gregoire Gentil <gregoire@gentil.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Use smc91x_platdata to setup smc91x, so we can get rid of OMAP specific stuff
in smc91x driver
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add 36xx CBP package support
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Remove old mux code for 34xx
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Replace omap_cfg_reg() with new style signal or gpio functions
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Otherwise we cannot limit new mux code to mach-omap2.
The same signal names should eventually work for other
omaps under mach-omap2.
Note that these pins don't need to be OMAP_PIN_INPUT_PULLUP,
just OMAP_PIN_INPUT is enough.
Cc: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add debugfs support for new mux code
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add new style mux init functions to omap3 board-*.c files
So far Beagle has been confirmed to be a CBB package,
and CM-T35 a CUS package.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add new style mux data for 34xx. This should also
work with 3630 easily by adding the processor subset
and ball data.
Note that this data is __initdata, and gets optimized
out except for the GPIO pins if CONFIG_OMAP_MUX
is not set.
Also note that this data uses omap3630 naming for
the SDMMC registers instead of 34xx naming with just
MMC.
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Initially only for 34xx. This code allows us to:
- Make the code more generic as the omap internal signal
names can stay the same across omap generations for some
devices
- Map mux registers to GPIO registers that is needed for
dynamic muxing of pins during off-idle
- Override bootloader mux values via kernel cmdline using
omap_mux=some.signa1=0x1234,some.signal2=0x1234
- View and set the mux registers via debugfs if
CONFIG_DEBUG_FS is enabled
Cc: Mike Rapoport <mike@compulab.co.il>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
intoduce omap_mux_{read,write}
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
An api at init for all dpll nodes seem to be
needed to reparent the dpll clk node to its
bypass clk in case the dpll is in bypass.
If not done this causes sequencing issues at init
during propogate_rate.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
|
|
Most of the dpll api's from dpll.c are reused for OMAP4.
This patch does extend a few api's for OMAP4 support.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
|
|
This patch moves all the dpll control api's to a
common file dpll.c. This is in preperation of omap4
support wherein most of these api's can be reused.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
|
|
This patch adds dummy hooks for OMAP4 dpll api's. Removes
dummy hooks for clkdev api's and enables CLKDEV
for OMAP4.
Also comments clockdomain calls from within the clock
framework as its not supported yet for OMAP4.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
|
|
This patch defines all the clock nodes in OMAP4430
platform. All the clock node structs and the clkdev table is
autogenerated using a python script (gen_clock_tree.py)
developed by Paul Walmsley, Benoit Cousson and Rajendra Nayak.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
|
|
This patch adds OMAP4 specific CM1 and CM2 module
register field masks. Auto generated using a python
script (gen_cm_shifts_and_mask.py) developed by Benoit
Cousson, Paul Walmsley and Rajendra Nayak.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
|
|
This patch adds OMAP4 specific PRM register bit field
shifts and masks. Auto generated using a python script
(gen_prm_shifts_and_mask.py) developed by Benoit Cousson,
Paul Walmsley and Rajendra Nayak.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
|
|
This patch adds OMAP4 specific PRM register defs. Auto generated
using a python script (gen_prm_4430_h.py) developed by Paul
Walmsley and Benoit Cousson.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
|
|
This patch adds OMAP4 specific CM1 and CM2 module
register defs. Autogenerated using a python scripts
(gen_cm1_4430_h.py,gen_cm2_4430_h.py) developed
by Paul Walmsley and Benoit Cousson.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
|
|
This patch adds the offsets for new modules in PRM
and CM for OMAP4
These are autogenerated using a python script (gen_prcm44xx_h.py)
developed by Paul Walmsley and Benoit Cousson.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
|
|
This patch fixes the PRM and CM base addresses and adds
a new CM2 base address for OMAP4
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
|
|
WARN if a clock/hwmod is missing a clockdomain association since
resulting hwmod will not be able to correctly enable/disable clocks.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Earlier, the hwmod code had considered the OCP_SYSCONFIG.CLOCKACTIVITY
bits to be incremental power saving bits, controlling internal IP
block clock gates. This was a misapprehension. The CLOCKACTIVITY
bits are used to indicate, in advance, which clocks will be cut when
the module acknowledges an idle request. This enables the IP block to
take whatever action is necessary to complete any in-progress work
before asserting its IdleAck.
In the current Linux-OMAP code, this implies that the clock framework
should be changing module CLOCKACTIVITY bits as module clocks are enabled
and disabled. We don't do that yet, but in the future, we should.
This must wait until the clock tree is annotated with omap_hwmod pointers
(or vice-versa). In the meantime, drop most of the hwmod code that
controls CLOCKACTIVITY bits to avoid confusion.
This patch has benefited from many illuminating discussions with (in
alphabetical order) Benoît Cousson <b-cousson@ti.com>, Rajendra Nayak
<rnayak@ti.com>, and Sebastien Sabatier <s-sabatier1@ti.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Sebastien Sabatier <s-sabatier1@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
|
|
Replace the existing u8 array of module MPU IRQ lines with a struct
that includes a name - similar to the existing struct
omap_hwmod_dma_info. Device drivers can then use
platform_get_resource_byname() to retrieve specific IRQs without nasty
dependencies on array ordering.
Thanks to Benoît Cousson <b-cousson@ti.com> and Kevin Hilman
<khilman@deeprootsystems.com> for feedback on this approach.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
|
|
This patch fills in the OCP_SYSCONFIG.AUTOIDLE handling in the OMAP
hwmod code.
After this patch, the hwmod code will set the module AUTOIDLE bit
(generally <module>.OCP_SYSCONFIG.AUTOIDLE) to 1 by default upon
enable. If the hwmod flag HWMOD_NO_OCP_AUTOIDLE is set, AUTOIDLE will
be set to 0 upon enable. Upon module disable, AUTOIDLE will be set to
1.
Enabling module autoidle should save some power. The only reason to
not set the OCP_SYSCONFIG.AUTOIDLE bit is if there is a bug in the
module RTL, e.g., the MPUINTC block on OMAP3.
Comments from Kevin Hilman <khilman@deeprootsystems.com> inspired this patch,
and Kevin tested an earlier version of this patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
|
|
Reprogram the module's OCP_SYSCONFIG register after module reset (SOFTRESET
= 1). This may not be needed, but the definition of the reset performed by
the SOFTRESET bit is unclear.
Kevin Hilman <khilman@deeprootsystems.com> tested an earlier version of
this patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
|
|
Fix loop bailout off-by-one bugs reported by Juha Leppänen
<juha_motorsportcom@luukku.com>.
This second version incorporates comments from Russell King
<linux@arm.linux.org.uk>. A new macro, 'omap_test_timeout', has
been created, with cleaner code, and existing code has been converted
to use it.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Juha Leppänen <juha_motorsportcom@luukku.com>
Cc: Russell King <linux@arm.linux.org.uk>
|
|
MPU power domain bank 0 bits are displayed in position of bank 1
in PWRSTS and PREPWRSTS registers. So read them from correct
position
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
behind Kconfig
The code that reprograms the SDRC memory controller during CORE DVFS,
mach-omap2/sram34xx.S:omap3_sram_configure_core_dpll(), does not
ensure that all L3 initiators are prevented from accessing the SDRAM
before modifying the SDRC AC timing and MR registers. This can cause
memory to be corrupted or cause the SDRC to enter an unpredictable
state. This patch places that code behind a Kconfig option,
CONFIG_OMAP3_SDRC_AC_TIMING for now, and adds a note explaining what
is going on. Ideally the code can be added back in once supporting
code is present to ensure that other initiators aren't touching the
SDRAM. At the very least, these registers should be reprogrammable
during kernel init to deal with buggy bootloaders. Users who know
that all other system initiators will not be touching the SDRAM can
also re-enable this Kconfig option.
This is a modification of a patch originally written by Rajendra Nayak
<rnayak@ti.com> (the original is at http://patchwork.kernel.org/patch/51927/).
Rather than removing the code completely, this patch just comments it out.
Thanks to Benoît Cousson <b-cousson@ti.com> and Christophe Sucur
<c-sucur@ti.com> for explaining the technical basis for this and for
explaining what can be done to make this path work in future code.
Thanks to Richard Woodruff <r-woodruff2@ti.com>, Nishanth Menon
<nm@ti.com>, and Olof Johansson <olof@lixom.net> for their comments.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Christophe Sucur <c-sucur@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Olof Johansson <olof@lixom.net>
|
|
IS_ERR returns only 1 or 0, and the functions return a negative error
in other cases anyways.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Replace some bare constants with power states.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
|
|
OMAP24xx chips don't support software-configurable sleep dependencies.
Test early for this so the compiler can redact the entire function body
on OMAP24xx.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Avoid cluttering the Kconfig space with debug options that are rarely
used. These can now be enabled and disabled by patching the "#undef DEBUG"
in the source files with "#define DEBUG", conforming to the practice for
the rest of the linux-omap code.
Also, while we're here, some lines in plat-omap/Kconfig use sets of
leading spaces when those lines should start with tabs. Convert most
of them to use tabs.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
|
