aboutsummaryrefslogtreecommitdiff
path: root/arch/arm/mach-pxa/pm.c
AgeCommit message (Collapse)Author
2006-06-30Remove obsolete #include <linux/config.h>Jörn Engel
Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de> Signed-off-by: Adrian Bunk <bunk@stusta.de>
2005-12-12[ARM] 3201/1: PXA27x: Prevent hangup during resume due to inadvertedly ↵Lothar Wassmann
enabling MBREQ (replaces: 3198/1) Patch from Lothar Wassmann The patch makes sure, that the ouptut functions of pins are restored before restoring the Alternat Function settings, preventing pins from being intermediately configured for undefined or unwanted alternate functions. Here is the original comment: I've got a PXA270 system that uses GPIO80 as nCS4. This system did hang on resume. Digging into the problem I found that the processor stalled immediately when restoring the GAFR2_U register which restored the alternate function for GPIO80. Since the GPDR registers were restored after the GAFR registers, the offending GPIO was configured as input at this point. Thus the alternate function that was in effect after restoring the GAFR was in fact the input function "MBREQ" instead of the output function "nCS4". The "PXA27x Processor Family Developer's Manual" (Footnote in Table 6-1 on page 6-3) states that: "The MBREQ alternate function must not be enabled until the PSSR[RDH] bit field is cleared. For more details, see Table 3-15, "PSSR Bit Definitions" on page 3-71." There is another note in the Developer's Manual (chapter 24.4.2 "GPIO operation as Alternate Function" on page 24-4) stating that: "Configuring a GPIO for an alternate function that is not defined for it causes unpredictable results." Since some GPIOs have no input function defined, and to prevent inadvertedly programming the MBREQ function on some pin, the GAFR registers should be restored after the GPDR registers have been restored. Additional provisions have to be made when the MBREQ function is actually required. The corresponding GAFR bits should not be restored with the regular GAFR restore, but must be set only after the PSSR bits have been cleared. Signed-off-by: Lothar Wassmann <LW@KARO-electronics.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2005-11-06[ARM] 3113/1: PXA: Allow machines to override (and also reuse) pxa pm functionsRichard Purdie
Patch from Richard Purdie Update the PXA pm.c file to allow machines (such as the Sharp Zaurus) to override the standard pm functions but reuse/wrap them where needed. The init call is made slightly earlier to give machine code an init level to override them in removing any race. Signed-off-by: Richard Purdie Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2005-06-19[PATCH] ARM SMP: Fix PXA/SA11x0 suspend resume crashRussell King
We need to re-initialise the stack pointers for undefined, IRQ and abort mode handlers whenever we resume. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2005-06-03[PATCH] ARM: 2691/1: PXA27x sleep fixes take 2Todd Poynor
Patch from Todd Poynor PXA27x sleep fixes: * set additional sleep/wakeup registers for Mainstone boards. * move CKEN=0 to pxa25x-specific code; that value is harmful on pxa27x. * save/restore additional registers, including some found necessary for C5 processors and/or newer blob versions. * enable future support of additional sleep modes for PXA27x (eg, standby, deep sleep). * split off cpu-specific sleep processing between pxa27x and pxa25x into separate files (partly in preparation for additional sleep modes). Includes fixes from David Burrage. Signed-off-by: Todd Poynor Signed-off-by: Nicolas Pitre Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2005-04-16Linux-2.6.12-rc2Linus Torvalds
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!