aboutsummaryrefslogtreecommitdiff
path: root/arch/arm/plat-s3c64xx/Makefile
AgeCommit message (Collapse)Author
2009-08-14ARM: S3C: Move S3C64xx audio devices into S3C64xx directoryMark Brown
Allowing us to make the Kconfig a little bit saner. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-06-16[ARM] S3C64XX: Initial support for DVFSMark Brown
This patch provides initial support for CPU frequency scaling on the Samsung S3C ARM processors. Currently only S3C6410 processors are supported, though addition of another data table with supported clock rates should be sufficient to enable support for further CPUs. Use the regulator framework to provide optional support for DVFS in the S3C cpufreq driver. When a software controllable regulator is configured the driver will use it to lower the supply voltage when running at a lower frequency, giving improved power savings. When regulator support is disabled or no regulator can be obtained for VDDARM the driver will fall back to scaling only the frequency. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-05-18[ARM] S3C: Merge next-s3c64xx-dma2 into for-rmk-develBen Dooks
Merge branch 'next-s3c64xx-dma2' into for-rmk-devel Conflicts: arch/arm/plat-s3c64xx/Makefile
2009-05-18[ARM] S3C64XX: DMA supportBen Dooks
Add support for the DMA blocks in the S3C64XX series of CPUS, which are based on the ARM PL080 PrimeCell system. Unfortunately, these DMA controllers diverge from the PL080 design by adding another DMA controller register and configuration for OneNAND. Signed-off-by: Ben Dooks <ben@simtec.co.uk> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-05-07[ARM] S3C64XX: Add S3C6400 SDHCI setup supportBen Dooks
Add support for S3C6400 SDHCI channels 0 and 1, making the GPIO code common to both S3C6400 and S3C6410. Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-05-07[ARM] S3C64XX: Add IRQ PM codeBen Dooks
Add support for saving the state of the IRQ registers over suspend. This requires moving the S3C64XX UART registers into <plat/regs-serial.h> and adding irq-pm.c which saves the state of all the IRQ registers. The irq-pm.c saves all the IRQ registers, including the IRQ_EINT and IRQ_EINT_GROUP registers as it was easier than adding three different files. Also ensuring that all the registers are restored to the same state as before suspend is considered to be the best thing to do. Note, we do not suspend the VIC here, this is done by the VIC driver itself. Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-05-07[ARM] S3C64XX: Initial support for PM (suspend to RAM)Ben Dooks
Add the initial support for the S3C64XX based systems to use suspend-to-RAM to sleep. Includes basic debugging for use with the SMDK6410 usign the LEDs on the baseboard. Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2008-12-15[ARM] S3C64XX: Add standard S3C64XX 24BPP LCD GPIO setupBen Dooks
Add a standard helper to configure the LCD output pins for a 24BPP display with VSYNC/HSYNC/VDEN. Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2008-12-15[ARM] S3C64XX: Setup functions for i2c bus 1.Ben Dooks
Add common gpio setup for i2c bus 1 on all current S3C64XX architectures. Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2008-12-15[ARM] S3C64XX: Add i2c device setup for I2C device 0Ben Dooks
Add the necessary device initialisation information for I2C device 0. Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2008-12-15[ARM] S3C64XX: GPIO library supportBen Dooks
Add gpiolib registration for the GPIOs available on the S3C64XX platform Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2008-12-15[ARM] S3C64XX: Add IRQ_EINT supportBen Dooks
Add the necessary code to support IRQ_EINT(x) on the S3C64XX series of CPUs. Note, since there is no GPIO configuration support in the kernel, the irq set_type method does not configure the relevant pin to interrupt. Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2008-12-15[ARM] S3C64XX: Clock support for S3C6400/S3C6410Ben Dooks
Add the PLL clock initialisation and clock registration and include the clocks sourced via CLKDIVx for most of the on-chip peripherals. Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2008-12-15[ARM] S3C64XX: Add initial clock frameworkBen Dooks
Add the initial clocks definitions for the s3c6400 and s3c6410. Move the epll and ext clock from the s3c2443 support into the common code. Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2008-12-15[ARM] S3C64XX: Common init code for S3C6400 and S3C6410Ben Dooks
Add the common initialisation code for both the S3C6400 and S3C6410, the UART registration. Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2008-12-15[ARM] S3C64XX: Add VIC0 and VIC1 sourced interriptsBen Dooks
Add and initialise the two VIC (PL192) found on the S3C64XX series CPUs. Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2008-12-15[ARM] S3C64XX: Basic CPU detection and map initialisationBen Dooks
Initialise the basic physical to virtual mappings and then detect the CPU that the system is being run on so that the cpu code code can call the correct initialisation code. Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2008-12-15[ARM] S3C64XX: Add UARTdevice definitionsBen Dooks
Add resources and information for the UART deviecs on the S3C64XX CPUs. Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2008-12-15[ARM] S3C64XX: Initial arch directoryBen Dooks
Add the initial PLAT_S3C64XX support files and directory structure. Signed-off-by: Ben Dooks <ben-linux@fluff.org>