| Age | Commit message (Collapse) | Author |
|---|
|
show_mem() was not correctly handling holes in the memory
map. It was treating the freed sections of the map as
though they contained valid struct page entries. This
could cause incorrect debugging output or even a kernel
panic.
This patch keeps the struct meminfo around after system
initialization so that show_mem() can use it when
scanning memory. show_mem() now walks over each bank
of each online node, rather than assuming that each node
contains a single contiguous bank.
Signed-off-by: Ray Lehtiniemi <rayl@mail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The timer LED is unusable at HZ=large, since it's got
a hard-wired value of 100 ticks per cycle; when HZ=1024
(for example) it's essentially always-on. This patch
just makes that be HZ ticks per cycle.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Add the new drivers, such as SPI, LED and RTC core,
to the s3c2410_defconfig.
Signed-off-by: Ben Dooks <ben-linux@fluff.irg>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Update the s3c2410_defconfig to 2.6.19-rc4
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Remove the bast_defconfig, as it has not been updated
since 2.6.13. The s3c2410_defconfig should be a good
replacement.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Remove the smdk2410_defconifg as it is out of data
and has not been touched since 2.6.11.
Use the s3c2410_defconfig instead.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This is a rework of the ixp4xx irq_chip implementation. The use of
two irq_chip structures and potentially switching between them is a
violation of the intended use of the IRQ framework. The current
implementation does not work with current in-kernel spinlock debugging
or lockdep due to lock recursion problems caused by calling
set_irq_chip/handler from within the chip's set_irq_type().
This patch goes back to using one irq_chip structure and handling the
differences between edge/level, normal/GPIO interrupts inside the
ack/mask/unmask routines themselves.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Deepak Saxena <dsaxena@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
ARM patch 3756/1 added HWCAP_IWMMXT. This patch adds support
for broadcasting that info via /proc/cpuinfo and sets it for
the CPU features of the PXA270.
I've booted 19rc3 on a pxa270 and confirmed that the /proc/cpuinfo
shows "iwmmxt" in the Features.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
s3c2410_gpio_getirq() holds for the S3C2412 build,
so ensure that it gets built for all the current
S3C24XX architectures
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
dma_sync_single is no more (and to be removed in 2.7) so this export should be dma_sync_single_for_cpu.
Also export dma_sync_single_for_device.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
"K4S281632b-1H" should read "K4S281632B-1H" (As it does everywhere
else). No more coffe!
Signed-off-by: Kristoffer Ericson <Kristoffer_e1@hotmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The second ethernet port on the Thecus n2100 was incorrectly assigned
to XINT1 instead of the correct XINT3 (PCI INTB instead of INTD), which
caused that port to be non-functional.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Add support for KBUILD_IMAGE on ARM. This takes the usual target
specifiers (zImage/Image/etc) in the same way that powerpc does
(iow, without the arch/arm/boot prefix).
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The SIGFPE signal should be generated if Division by Zero exception is detected.
Signed-off-by: Takashi Ohmasa <ohmasa.takashi@jp.panasonic.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The significand should be shifted until the value of bit [62] is 1
to normalize the denormal double number.
Signed-off-by: Takashi Ohmasa <ohmasa.takashi@jp.panasonic.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The IRQ changes a while back broke the build for SMP machines.
Fix up the SMP code to use set_irq_regs/get_irq_regs as
appropriate. Also, fix a warning in arch/arm/kernel/time.c
where 'regs' becomes unused for SMP builds.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Add a vmlinux.lds.h helper macro for defining the eight-level initcall table,
teach all the architectures to use it.
This is a prerequisite for a patch which performs initcall synchronisation for
multithreaded-probing.
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
[ Added AVR32 as well ]
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
HAS_TOUCHSCREEN_ADS7843_LH7 and HAS_TOUCHSCREEN_ADC_LH7 are referenced
but not defined in the LH7A40x configuration. Comment them out to
prevent them causing warnings.
Marc Singer said:
Feel free to remove the Kconfig lines. I'll add it back with
the rest of the config entries.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
A couple of missing semicolons.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog: (33 commits)
[WATCHDOG] remove experimental on iTCO_wdt.c
[WATCHDOG] Atmel AT91RM9200 rename.
[WATCHDOG] includes for sample watchdog program.
[WATCHDOG] watchdog/iTCO_wdt: fix bug related to gcc uninit warning
[WATCHDOG] add ich8 support to iTCO_wdt.c (patch 2)
[WATCHDOG] add ich8 support to iTCO_wdt.c
[WATCHDOG] ioremap balanced with iounmap for drivers/char/watchdog/s3c2410_wdt.c
[WATCHDOG] w83697hf/hg WDT driver - Kconfig patch
[WATCHDOG] w83697hf/hg WDT driver - autodetect patch
[WATCHDOG] w83697hf/hg WDT driver - patch 16
[WATCHDOG] w83697hf/hg WDT driver - patch 15
[WATCHDOG] w83697hf/hg WDT driver - patch 14
[WATCHDOG] w83697hf/hg WDT driver - patch 13
[WATCHDOG] w83697hf/hg WDT driver - patch 12
[WATCHDOG] w83697hf/hg WDT driver - patch 11
[WATCHDOG] w83697hf/hg WDT driver - patch 10
[WATCHDOG] w83697hf/hg WDT driver - patch 9
[WATCHDOG] w83697hf/hg WDT driver - patch 8
[WATCHDOG] w83697hf/hg WDT driver - patch 7
[WATCHDOG] w83697hf/hg WDT driver - patch 6
...
|
|
Fix one more compile breakage caused by the post -rc1 IRQ changes.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Some ARM platforms were still broken as a result of the IRQ register
passing changes, mostly due to a missing linux/irq.h include.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This adds correct sdram params for K4S281632B-1H and sets the jornada to use them by default.
Signed-off-by: Kristoffer Ericson
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The new Atmel AT91SAM9261 and AT91SAM9260 processors use a different
internal watchdog peripheral. This watchdog driver is therefore
AT91RM9200-specific.
This patch renames at91_wdt.c to at91rm9200_wdt.c, and changes the name
of the configuration option.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Use the new typedef for interrupt handler function pointers rather than
actually spelling out the full thing each time. This was scripted with the
following small shell script:
#!/bin/sh
egrep -nHrl -e 'irqreturn_t[ ]*[(][*]' $* |
while read i
do
echo $i
perl -pi -e 's/irqreturn_t\s*[(]\s*[*]\s*([_a-zA-Z0-9]*)\s*[)]\s*[(]\s*int\s*,\s*void\s*[*]\s*[)]/irq_handler_t \1/g' $i || exit $?
done
Signed-Off-By: David Howells <dhowells@redhat.com>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This should fix up the per-cpu irq register pointer if we have nested
hardware interrupts.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
With the following patch, the ixp4xxdefconfig builds correctly. I'll
test some more configs if I get some time.
Signed-off-by: Frederik Deweerdt <frederik.deweerdt@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Untested, but this should fix up the bulk of the totally mechanical
issues, and should make the actual detail fixing easier.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
In order to initialize the serial console early, the atmel_serial
driver had to do a hack where it compared the physical address of the
port with an address known to be permanently mapped, and used it as a
virtual address. This got around the limitation that ioremap() isn't
always available when the console is being initalized.
This patch removes that hack and replaces it with a new "regs" field
in struct atmel_uart_data that the board-specific code can initialize
to a fixed virtual mapping for platform devices where this is possible.
It also initializes the DBGU's regs field with the address the driver
used to check against.
On AVR32, the "regs" field is initialized from the physical base
address when this it can be accessed through a permanently 1:1 mapped
segment, i.e. the P4 segment.
If regs is NULL, the console initialization is delayed until the "real"
driver is up and running and ioremap() can be used.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Rename the following public definitions:
* AT91_NR_UART -> ATMEL_MAX_UART
* struct at91_uart_data -> struct atmel_uart_data
* at91_default_console_device -> atmel_default_console_device
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Rename the "at91_usart" platform driver "atmel_usart" and update
platform devices accordingly.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Rename the following Kconfig symbols:
* CONFIG_SERIAL_AT91 -> CONFIG_SERIAL_ATMEL
* CONFIG_SERIAL_AT91_CONSOLE -> CONFIG_SERIAL_ATMEL_CONSOLE
* CONFIG_SERIAL_AT91_TTYAT -> CONFIG_SERIAL_ATMEL_TTYAT
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
kbuild explicitly includes this at build time.
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
Many files include the filename at the beginning, serveral used a wrong one.
Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Randy brought it to my attention that in proper english "can not" should always
be written "cannot". I donot see any reason to argue, even if I mightnot
understand why this rule exists. This patch fixes "can not" in several
Documentation files as well as three Kconfigs.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
The patch below corrects multiple occurances of "the the"
typos across several files, both in source comments and KConfig files.
There is no actual code changed, only text. Note this only affects the /arch
directory, and I believe I could find many more elsewhere. :)
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 3848/1: pxafb: Add option of fixing video modes and spitz QVGA mode support
[ARM] 3880/1: remove the last trace of iop31x support
[ARM] 3879/1: ep93xx: instantiate platform devices for ep93xx ethernet
[ARM] 3809/3: get rid of 4 megabyte kernel image size limit
[ARM] Fix XIP_KERNEL build error in arch/arm/mm/mmu.c
[ARM] 3874/1: Remove leftover usage of asm/timeofday.h
|
|
It looks like Zach Brown's patch pr_debug-check-pr_debug-arguments
worked as inteded. That is, it doesn't "allow completely incorrect code
to build." :).
The arm build fails with the following message:
CC arch/arm/vfp/vfpsingle.o
arch/arm/vfp/vfpsingle.c: In function `__vfp_single_normaliseround':
arch/arm/vfp/vfpsingle.c:201: error: `func' undeclared (first use in
this function)
arch/arm/vfp/vfpsingle.c:201: error: (Each undeclared identifier is
reported only once
arch/arm/vfp/vfpsingle.c:201: error: for each function it appears in.)
make[1]: *** [arch/arm/vfp/vfpsingle.o] Error 1
make: *** [arch/arm/vfp] Error 2
The following patch fixes the issue by using func only when DEBUG is
defined.
Signed-off-by: Frederik Deweerdt <frederik.deweerdt@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Zach Brown <zach.brown@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Add watchdog support for Philips PNX4008 ARM board inlined.
Signed-off-by: Vitaly Wool <vitalywool@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Some architectures provide an execve function that does not set errno, but
instead returns the result code directly. Rename these to kernel_execve to
get the right semantics there. Moreover, there is no reasone for any of these
architectures to still provide __KERNEL_SYSCALLS__ or _syscallN macros, so
remove these right away.
[akpm@osdl.org: build fix]
[bunk@stusta.de: build fix]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andi Kleen <ak@muc.de>
Acked-by: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Hirokazu Takata <takata.hirokazu@renesas.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Richard Curnow <rc@rc0.org.uk>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp>
Cc: Chris Zankel <chris@zankel.net>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
In some places, particularly drivers and __init code, the init utsns is the
appropriate one to use. This patch replaces those with a the init_utsname
helper.
Changes: Removed several uses of init_utsname(). Hope I picked all the
right ones in net/ipv4/ipconfig.c. These are now changed to
utsname() (the per-process namespace utsname) in the previous
patch (2/7)
[akpm@osdl.org: CIFS fix]
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Cc: Kirill Korotaev <dev@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: Andrey Savochkin <saw@sw.ru>
Cc: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Move the init_nsproxy definition out of arch/ into kernel/nsproxy.c. This
avoids all arches having to be updated. Compiles and boots on s390.
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Cc: Kirill Korotaev <dev@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: Andrey Savochkin <saw@sw.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
