Age | Commit message (Collapse) | Author |
|
This adds DSA switch instantiation hooks to the orion5x and the
kirkwood ARM SoC platform code, and instantiates the DSA switch
driver on the 88F5181L FXO RD, the 88F5181L GE RD, the 6183 AP GE
RD, the Linksys WRT350n v2, and the 88F6281 RD boards.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Nicolas Pitre <nico@marvell.com>
Tested-by: Peter van Valderen <linux@ddcrew.com>
Tested-by: Dirk Teurlings <dirk@upexia.nl>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
|
|
On the mv78xx0 development board, eth2 and eth3 do not have
corresponding PHYs, but are internally connected, as a way of
facilitating communication between the two CPU cores. Since there are
no PHYs, we need to tell the network driver explicitly to force the
link on eth2 and eth3 up, to 1000 Mb/s full duplex.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
|
|
* 'personality' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[PATCH] remove unused ibcs2/PER_SVR4 in SET_PERSONALITY
|
|
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (51 commits)
[ARM] 5308/1: Fix Viper ISA IRQ handling
[ARM] 5307/1: pxa: fix CM-X2XX PCMCIA build error
[ARM] 5306/1: pxa: fix build error on CM-X270
[ARM] 5302/1: ARM: OMAP: Revert omap3 WDT changes to avoid merge conflict
[ARM] 5305/1: ARM: OMAP: Fix compile of McBSP by removing unnecessary check
[ARM] 5301/1: ARM: OMAP: Add missing irq defines
ARM: OMAP3: Add default kernel config for OMAP LDP
ARM: OMAP3: Add basic board support for OMAP LDP
ARM: OMAP3: Defconfig for the Gumstix Overo board (rev 3)
ARM: OMAP3: Add support for the Gumstix Overo board (rev 3)
ARM: OMAP3: Add Beagle defconfig
ARM: OMAP3: Add minimal Beagle board support
ARM: OMAP3: Add minimal omap3430 support
ARM: OMAP2: Fix sparse, checkpatch warnings in OMAP2/3 IRQ code
ARM: OMAP: Fixes to omap_mcbsp_request function
ARM: OMAP: Add support for OMAP2430 in McBSP
ARM: OMAP: Add support for McBSP devices 3 - 5 on 34xx
ARM: OMAP: Allocate McBSP devices dynamically
Fix sections for omap-mcbsp platform driver
[ARM] S3C24XX: Additional include moves
...
|
|
Add a pin configuration callback for the s3c24xx SPI driver, as there are
several options depending on the channel and the chip in use.
This is needed as the controller may not have been setup by the initial
bootloader and the fact that the SPI controller gets reset over
suspend/resume into slave mode but the GPIO function registers do not.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The SET_PERSONALITY macro is always called with a second argument of 0.
Remove the ibcs argument and the various tests to set the PER_SVR4
personality.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
As policy->governor is already set to CPUFREQ_DEFAULT_GOVERNOR in the
(always built-in) cpufreq core, we do not need to set it in the drivers.
This fixes the sparc64 allmodconfig build failure.
Also, remove a totally useles setting of ->policy in cpufreq-pxa3xx.c.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Conflicts:
arch/arm/mach-versatile/core.c
|
|
The ISA IRQ renumbering broke the Viper ISA code in interesting ways.
It originally assumed that ISA interrupt were numbered in the order that
is defined by the CPLD registers. Unfortunately, this is no longer the
case.
Furthermore, the viper_irq_handler() function being a chained IRQ
handler, it must ACK the interrupt by itself, or the handler will be
immediately reentered, with the expected damages.
This fix was made possible thanks to the help of David Raeman, who
provided debug information and tested each version of this patch.
Tested-by: David Raeman <david.raeman@gmail.com>
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Fix build for CM-X2XX with CONFIG_RTC_DRV_V3020 unset:
CC arch/arm/mach-pxa/cm-x270.o
/mnt/sdb1/git/linux-2.6-arm/arch/arm/mach-pxa/cm-x270.c: In function 'cmx270_init':
/mnt/sdb1/git/linux-2.6-arm/arch/arm/mach-pxa/cm-x270.c:338: error: implicit declaration of function 'cmx270_init_rtc'
make[2]: *** [arch/arm/mach-pxa/cm-x270.o] Error 1
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Conflicts:
arch/arm/mach-versatile/core.c
|
|
Conflicts:
arch/arm/mach-omap2/gpmc.c
arch/arm/mach-omap2/irq.c
|
|
With the upcoming WDT patches OMAP_WDT_BASE is no longer needed
in devices.c. Revert some earlier omap3 changes to avoid merge
conflicts with the WDT patches.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Recent McBSP patches changed to allocating devices dynamically
and the check for OMAP_MAX_MCBSP_COUNT became unnecessary.
The check for OMAP_MAX_MCBSP_COUNT should have been removed with
the earlier McBSP patches in devices.c but was accidentally left
out.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Some McBSP irq defines were missing that should have been added
with the earlier McBSP patches.
Add the missing McBSP irqs, and a few other missing irqs as
defined in linux-omap tree. Also add a blank line to separate
irq defines from the irq line calculations.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Based on David Brownell's patch for tps65010 and previous work by
Felipe Balbi, this patch finishes converting isp1301_omap to a
new-style i2c driver.
There's definitely room for further drivers cleanups, but these are
out of the scope of this patch.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (313 commits)
V4L/DVB (9186): Added support for Prof 7300 DVB-S/S2 cards
V4L/DVB (9185): S2API: Ensure we have a reasonable ROLLOFF default
V4L/DVB (9184): cx24116: Change the default SNR units back to percentage by default.
V4L/DVB (9183): S2API: Return error of the caller provides 0 commands.
V4L/DVB (9182): S2API: Added support for DTV_HIERARCHY
V4L/DVB (9181): S2API: Add support fot DTV_GUARD_INTERVAL and DTV_TRANSMISSION_MODE
V4L/DVB (9180): S2API: Added support for DTV_CODE_RATE_HP/LP
V4L/DVB (9179): S2API: frontend.h cleanup
V4L/DVB (9178): cx24116: Add module parameter to return SNR as ESNO.
V4L/DVB (9177): S2API: Change _8PSK / _16APSK to PSK_8 and APSK_16
V4L/DVB (9176): Add support for DvbWorld USB cards with STV0288 demodulator.
V4L/DVB (9175): Remove NULL pointer in stb6000 driver.
V4L/DVB (9174): Allow custom inittab for ST STV0288 demodulator.
V4L/DVB (9173): S2API: Remove the hardcoded command limit during validation
V4L/DVB (9172): S2API: Bugfix related to DVB-S / DVB-S2 tuning for the legacy API.
V4L/DVB (9171): S2API: Stop an OOPS if illegal commands are dumped in S2API.
V4L/DVB (9170): cx24116: Sanity checking to data input via S2API to the cx24116 demod.
V4L/DVB (9169): uvcvideo: Support two new Bison Electronics webcams.
V4L/DVB (9168): Add support for MSI TV@nywhere Plus remote
V4L/DVB: v4l2-dev: remove duplicated #include
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/adobriyan/proc
* 'proc' of git://git.kernel.org/pub/scm/linux/kernel/git/adobriyan/proc:
proc: remove kernel.maps_protect
proc: remove now unneeded ADDBUF macro
[PATCH] proc: show personality via /proc/pid/personality
[PATCH] signal, procfs: some lock_task_sighand() users do not need rcu_read_lock()
proc: move PROC_PAGE_MONITOR to fs/proc/Kconfig
proc: make grab_header() static
proc: remove unused get_dma_list()
proc: remove dummy vmcore_open()
proc: proc_sys_root tweak
proc: fix return value of proc_reg_open() in "too late" case
Fixed up trivial conflict in removed file arch/sparc/include/asm/dma_32.h
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts:
include/asm-x86/statfs.h
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] orion5x_wdt.c: add spinlocking
[WATCHDOG] Orion: add hardware watchdog support
[WATCHDOG] omap_wdt.c: cleanup a bit omap_wdt.c
[WATCHDOG] omap_wdt.c: another ioremap() fix
[WATCHDOG] omap_wdt.c: sync linux-omap changes
[WATCHDOG] Add AT91SAM9X watchdog
[WATCHDOG] Add driver for winbond w83697ug/uf watchdog feature
[WATCHDOG] add watchdog driver IT8716 IT8726 IT8712J/K
|
|
sensor driver
Make .power and .reset callbacks per camera instead of per host, also move
their invocation to camera drivers.
.arch/arm/mach-pxa/include/mach/camera.h | 2 -
Signed-off-by: Stefan Herbrechtsmeier <hbmeier@hni.uni-paderborn.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (236 commits)
[ARM] 5300/1: fixup spitz reset during boot
[ARM] 5295/1: make ZONE_DMA optional
[ARM] 5239/1: Palm Zire 72 power management support
[ARM] 5298/1: Drop desc_handle_irq()
[ARM] 5297/1: [KS8695] Fix two compile-time warnings
[ARM] 5296/1: [KS8695] Replace macro's with trailing underscores.
[ARM] pxa: allow multi-machine PCMCIA builds
[ARM] pxa: add preliminary CPUFREQ support for PXA3xx
[ARM] pxa: add missing ACCR bit definitions to pxa3xx-regs.h
[ARM] pxa: rename cpu-pxa.c to cpufreq-pxa2xx.c
[ARM] pxa/zylonite: add support for USB OHCI
[ARM] ohci-pxa27x: use ioremap() and offset for register access
[ARM] ohci-pxa27x: introduce pxa27x_clear_otgph()
[ARM] ohci-pxa27x: use platform_get_{irq,resource} for the resource
[ARM] ohci-pxa27x: move OHCI controller specific registers into the driver
[ARM] ohci-pxa27x: introduce flags to avoid direct access to OHCI registers
[ARM] pxa: move I2S register and bit definitions into pxa2xx-i2s.c
[ARM] pxa: simplify DMA register definitions
[ARM] pxa: make additional DCSR bits valid for PXA3xx
[ARM] pxa: move i2c register and bit definitions into i2c-pxa.c
...
Fixed up conflicts in
arch/arm/mach-versatile/core.c
sound/soc/pxa/pxa2xx-ac97.c
sound/soc/pxa/pxa2xx-i2s.c
manually.
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1075 commits)
myri10ge: update driver version number to 1.4.3-1.369
r8169: add shutdown handler
r8169: preliminary 8168d support
r8169: support additional 8168cp chipset
r8169: change default behavior for mildly identified 8168c chipsets
r8169: add a new 8168cp flavor
r8169: add a new 8168c flavor (bis)
r8169: add a new 8168c flavor
r8169: sync existing 8168 device hardware start sequences with vendor driver
r8169: 8168b Tx performance tweak
r8169: make room for more specific 8168 hardware start procedure
r8169: shuffle some registers handling around (8168 operation only)
r8169: new phy init parameters for the 8168b
r8169: update phy init parameters
r8169: wake up the PHY of the 8168
af_key: fix SADB_X_SPDDELETE response
ath9k: Fix return code when ath9k_hw_setpower() fails on reset
ath9k: remove nasty FAIL macro from ath9k_hw_reset()
gre: minor cleanups in netlink interface
gre: fix copy and paste error
...
|
|
* 'for-linus' of git://git.alsa-project.org/alsa-kernel: (258 commits)
ALSA: hda: VREF powerdown for headphones
ALSA: hda: STAC_HP_M4
ALSA: ASoC: Check for machine type in GTA01 machine driver
ALSA: mtpav - Fix race in probe
ALSA: usb-audio: dynamic detection of MIDI interfaces in uaxx-quirk
ALSA: Add a note on dependency of RTC stuff
ALSA: ASoC: add new param mux to dapm_mux_update_power
ALSA: Increase components array size
ALSA: ASoC: Correct inverted Mic PGA Switch control in wm8510 driver
ALSA: hda: comment typo fix
ALSA: hda: comment typo fix
ALSA: hda - Fix PCI SSID for ASROCK K18N78FullHD-hSLI
ALSA: snd-usb-audio: support for Edirol UA-4FX device
ALSA: usb - Fix possible Oops at USB-MIDI disconnection
ALSA: hda - Fix another ALC889A (rev 0x100101)
ALSA: hda: add more board-specific information for Realtek ALC662 rev1
ALSA: Correct Vladimir Barinov's e-mail address
ALSA: cs46xx: Add PCI IDs for TerraTec and Hercules cards
ALSA: hda: SPDIF stream muting support
ALSA: hda: appletv support
...
|
|
Some machines don't have the pullup/down on their reset
pin, so configuring the reset generating pin as input makes
them reset immediately. Fix that by making reset pin direction
configurable.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6 into omap-all
|
|
This patch allows the use of the hardware watchdog in the
Marvell Orion series of ARM SoCs.
Signed-off-by: Sylver Bruneau <sylver.bruneau@googlemail.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
These are changes that have been sitting in linux-omap
and were never sent upstream.
Hopefully, it'll never happen again at least for this
driver.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
This patch adds a default config for the OMAP LDP platform.
Signed-off-by: Nishant Kamat <nskamat@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This adds minimal board support for the OMAP3430 LDP development platform.
Signed-off-by: Nishant Kamat <nskamat@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add defconfig for the Gumstix Overo board
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
|
|
Merge branch 'orion-devel' into devel
|
|
Merge branch 'davinci' into devel
|
|
git://pasiphae.extern.pengutronix.de/git/imx/linux-2.6.git
Merge branch 'imx-devel' into devel
|
|
Conflicts:
arch/arm/mach-pxa/Kconfig
arch/arm/mach-pxa/corgi.c
arch/arm/mach-pxa/include/mach/hardware.h
arch/arm/mach-pxa/spitz.c
|
|
|
|
Conflicts:
arch/arm/Kconfig
|
|
'sa1100' into devel
|
|
Most ARM machines don't need a special "DMA" memory zone, and
when configured out, the kernel becomes a bit smaller:
| text data bss dec hex filename
|3826182 102384 111700 4040266 3da64a vmlinux
|3823593 101616 111700 4036909 3d992d vmlinux.nodmazone
This is because the system now has only one zone total which effect is
to optimize away many conditionals in page allocation paths.
So let's configure this zone only on machines that need split zones.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6 into omap-all
|
|
This patch adds minimal overo support.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add Beagle defconfig
Signed-off-by: Syed Mohammed, Khasim <khasim@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add minimal Beagle board support. Based on earlier patches
by Syed Mohammed Khasim with some fixes from linux-omap tree.
Signed-off-by: Syed Mohammed Khasim <khasim@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add minimal omap3430 support based on earlier patches from
Syed Mohammed Khasim. Also merge in omap34xx SRAM support
from Karthik Dasu and use consistent naming for sram init
functions.
Also do following changes that make 34xx support usable:
- Remove unused sram.c functions for 34xx
- Rename IRQ_SIR_IRQ to INTCPS_SIR_IRQ and define it locally
in entry-macro.S
- Update mach-omap2/io.c to support 2420, 2430, and 34xx
- Also merge in 34xx GPMC changes to add fields wr_access and
wr_data_mux_bus from Adrian Hunter
- Remove memory initialization call omap2_init_memory() until
until more generic memory initialization patches are posted.
It's OK to rely on bootloader initialization until then.
Signed-off-by: Syed Mohammed, Khasim <khasim@ti.com>
Signed-off-by: Karthik Dasu<karthik-dp@ti.com>
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fix sparse warnings in mach-omap2/irq.c. Fix by defining
intc_bank_write_reg() and intc_bank_read_reg(), and convert INTC module
register access to use them rather than __raw_{read,write}l.
Also clear up some checkpatch warnings involving includes from asm/
rather than linux/.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch contains Palm Zire 72 power
management support.
Depends on #5238/1
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
desc_handle_irq() was declared as obsolete since long ago.
Replace it with generic_handle_irq()
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Fix two warnings when compiling for the KS8695 processor.
arch/arm/include/asm/dma-mapping.h: In function 'dma_to_virt':
arch/arm/include/asm/dma-mapping.h:40: warning: return makes pointer
from integer without a cast
Section mismatch in reference from the function pcibios_fixup_bus() to
the (unknown reference) .devinit.text:(unknown)
The function pcibios_fixup_bus() references
the (unknown reference) __devinit (unknown).
This is often because pcibios_fixup_bus lacks a __devinit
annotation or the annotation of (unknown) is wrong.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|