aboutsummaryrefslogtreecommitdiff
path: root/arch/avr32/boards/atngw100
AgeCommit message (Collapse)Author
2008-01-25[AVR32] Add support for AT32AP7001 and AT32AP7002Haavard Skinnemoen
These are derivatives of the AT32AP7000 chip, which means that most of the code stays the same. Rename a few files, functions, definitions and config symbols to reflect that they apply to all AP700x chips, and exclude some platform devices from chips where they aren't present. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-10-11[AVR32] ngw100 i2c-gpio tweaksDavid Brownell
Make the NGW100 bitbang i2c use open drain signaling. Also, speed it up, so it's closer to 100 kHz ... the code paths seem to be long enough that the udelay isn't dominating bit times. The peak bit rate I observed was around 125 kHz, but that's with large delays (usually before ACK/NAK) which hold the overall rate down to around 80 kHz (call it 100 usec/byte on average). Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-10-11[AVR32] SMC configuration in clock cyclesKristoffer Nyborg Gregertsen
This patch makes the SMC configuration take timings in clock cycles instead of nanoseconds. A function to calculate timings in clock cycles is added. This patch removes the rounding troubles of the previous SMC configuration method. [hskinnemoen@atmel.com: fix atstk1002/atngw100 flash config] Signed-off-by: Kristoffer Nyborg Gregertsen <gregerts@stud.ntnu.no> Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-10-11[AVR32] Wire up USBA deviceHaavard Skinnemoen
Implement at32_add_device_usba() and use it to wire up the USBA device on ATSTK1000 and ATNGW100. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-08-15[AVR32] Wire up i2c-gpio on the ATNGW100 boardHaavard Skinnemoen
The NGW100 has a board controller which is hooked up to the TWI lines on AP7000. Since the TWI driver isn't in mainline, use the i2c-gpio driver in the mean time. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-07-16leds: leds-gpio for ngw100David Brownell
Add GPIO leds to the NGW100 platform and its defconfig. Access through /sys/class/leds/{a,b,sys}/* files; one defaults to a heartbeat. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
2007-06-23[AVR32] NGW100, Remove relics of the old USART mapping schemeben.nizette@iinet.net.au
USART mapping used to be accomplished by the manual filling of at32_usart_map[] and at32_nr_usarts. This has now been replaced with at32_map_usart() so we can remove these variables. Signed-off-by: Ben Nizette <ben.nizette@iinet.net.au> Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-04-27[AVR32] Board code for ATNGW100Haavard Skinnemoen
Add board code and defconfig for the ATNGW100 Network Gateway kit. For more information about this board, see http://www.atmel.com/dyn/products/tools_card.asp?tool_id=4102 Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>