aboutsummaryrefslogtreecommitdiff
path: root/arch/avr32
AgeCommit message (Collapse)Author
2008-10-12avr32: Fix build failures in board codeHaavard Skinnemoen
Fix a few instances of board code breakage introduced by the atmel-mci platform interface changes. Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-10-12avr32: Allow selecting multiple pins at onceJulien May
at32_select_periph() now takes an u32 bitmask rather than a single pin. This allows to set multiple pins at once. Signed-off-by: Alex Raimondi <mailinglist@miromico.ch> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-10-12Merge branch 'master' of ↵Haavard Skinnemoen
git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/atmel-mci-2.6.28
2008-10-08avr32: Minor pm_power_off cleanupHaavard Skinnemoen
Include <linux/pm.h> to see the declaration of pm_power_off, and remove unneeded NULL initializer. Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-10-08avr32: Implement {read,write}[bwl]_beHaavard Skinnemoen
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-10-05atmel-mci: Add experimental DMA supportHaavard Skinnemoen
This adds support for DMA transfers through the generic DMA engine framework with the DMA slave extensions. The driver has been tested using mmc-block and ext3fs on several SD, SDHC and MMC+ cards. Reads and writes work fine, with read transfer rates up to 7.5 MiB/s on fast cards with debugging disabled. Unfortunately, the driver has been known to lock up from time to time with DMA enabled, so DMA support is currently optional and marked EXPERIMENTAL. However, I didn't see any problems while testing 13 different cards (MMC, SD and SDHC of different brands and sizes), so I suspect the "Initialize BLKR before sending data transfer command" fix that was posted earlier fixed this as well. Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-10-05atmel-mci: support multiple mmc slotsHaavard Skinnemoen
The Atmel MCI controller can drive multiple cards through separate sets of pins, but only one at a time. This patch adds support for multiplexing access to the controller so that multiple card slots can be used as if they were hooked up to separate mmc controllers. The atmel-mci driver registers each slot as a separate mmc_host. Both access the same common controller state, but they also have some state on their own for card detection/write protect handling, and separate shadows of the MR and SDCR registers. When one of the slots receives a request from the mmc core, the common controller state is checked. If it's idle, the request is submitted immediately. If not, the request is added to a queue. When a request is done, the queue is checked and if there is a queued request, it is submitted before the completion callback is called. This patch also includes a few cleanups and fixes, including a locking overhaul. I had to change the locking extensively in any case, so I might as well try to get it right. The driver no longer takes any irq-safe locks, which may or may not improve the overall system performance. This patch also adds a bit of documentation of the internal data structures. Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-10-05atmel-mci: Platform code for supporting multiple mmc slotsHaavard Skinnemoen
Add the necessary platform infrastructure to support multiple mmc/sdcard slots all at once through a single controller. Currently, the driver will use the first valid slot it finds and stick with that, but later patches will add support for switching between several slots on the fly. Extend the platform data structure with per-slot information: MMC/SDcard bus width and card detect/write protect pins. This will affect the pin muxing as well as the capabilities announced to the mmc core. Note that board code is now required to supply a mci_platform_data struct to at32_add_device_mci(). Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-10-05avr32: Replace static clock list with dynamic linked listAlex Raimondi
This replaces the at32_clock_list array with a linked list. Clocks can now be registered (added) to the list. Signed-off-by: Alex Raimondi <raimondi@miromico.ch> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-09-22avr32: Use platform_driver_probe for pdc platform driverUwe Kleine-König
The probe function of the pdc platform driver lives in the init section and so a pdc device that is created after the init section is discarded probably results in an oops. Even if this cannot happen, using platform_driver_probe is cleaner. (If this can happen and should be supported the probe function must live in the devinit section instead.) Signed-off-by: Uwe Kleine-König <ukleinek@strlen.de> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-09-22avr32: Use platform_driver_probe for pio platform driverUwe Kleine-König
The probe function of the pio platform driver lives in the init section and so a pio device that is created after the init section is discarded probably results in an oops. Even if this cannot happen, using platform_driver_probe is cleaner. (If this can happen and should be supported the probe function must live in the devinit section instead.) Signed-off-by: Uwe Kleine-König <ukleinek@strlen.de> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-09-22avr32: Provide a way to deselect pins in the portmuxHaavard Skinnemoen
Currently, setting up the portmux is completely one-shot: Once a pin is muxed, the portmux driver will complain loudly and refuse to do anything if you try to set up the same pin again. Sometimes, it may be necessary to change the configuration of a pin after it has been set up initially. This patch adds a way to undo the previous configuration, allowing the pin to be reconfigured. Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-09-22ngw100: export J15 through sysfsDavid Brownell
The NGW100 board has jumper J15 (near the reset button) which is unused. This patch exports it through the GPIO sysfs support (as /sys/class/gpio/gpio62/value) so that it's easily queried by boot scripts or whatever might want to know if the jumper has been installed (value = 0) or not (value = 1, "default"). Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> [haavard.skinnemoen@atmel.com: add missing include] Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-09-22avr32: Allow fine-grained control over LCDC pinsJulien May
This replaces the pin_config param with an u64 pin_mask in at32_add_device_lcdc, allowing a board-maintainer to indivually select specific lcdc pins. Signed-off-by: Alex Raimondi <raimondi@miromico.ch> Signed-off-by: Julien May <jmay@miromico.ch> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-09-22avr32: added mem kernel command line option supportMarco Stornelli
Signed-off-by: Marco Stornelli <marco.stornelli@gmail.com> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-09-22Add kernel support for oprofile callgraphs on AVR32Nikolaus Voss
This patch adds backtracing capability to oprofile profiling in kernel and user mode on AVR32. This is done by going through the frames on the stack and adding oprofile traces for all return addresses. The code being profiled has to be compiled with frame pointers to make this work. Signed-off-by: Nikolaus Voss <n.voss@weinmann.de> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-09-22avr32: use the new byteorder headersHarvey Harrison
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> [haavard.skinnemoen@atmel.com: fix <mach/io.h> build breakage] Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-09-19avr32: nmi_enter() without nmi_exit()Manfred Spraul
While updating the rcu code, I noticed that do_nmi() for AVR32 is odd: There is an nmi_enter() call without an nmi_exit(). This can't be correct, it breaks rcu (at least the preempt version) and lockdep. [haavard.skinnemoen@atmel.com: fixed another case that returned directly] Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-09-19avr32: fix sys_sync_file_range() call conventionHans-Christian Egtvedt
On AVR32, all parameters beyond the 5th are passed on the stack. System calls don't use the stack -- they borrow a callee-saved register instead. This means that syscalls that take 6 parameters must be called through a stub that pushes the last parameter on the stack. This patch adds a stub for sync_file_range syscall on AVR32 architecture. Tested with uClibc snapshot. Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-09-19avr32: add generic_find_next_le_bit bit functionHans-Christian Egtvedt
This patch implements the generic_find_next_le_bit bit function for AVR32 architecture. This is used by EXT4 file system. Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-09-19avr32: add .gitignore filesMarkus Heidelberg
Ignore Kernel binaries, kernel/vmlinux.lds and a log file. Signed-off-by: Markus Heidelberg <markus.heidelberg@web.de> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-09-19atstk1000: fix build breakage with BOARD_ATSTK100X_SW2_CUSTOM=yHaavard Skinnemoen
The #ifdef surrounding the code adding the mmc controller had a typo, causing it to be compiled even when mmc was supposed to be disabled. Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-09-01avr32: pm_standby low-power ram bug fixHumphrey Bucknell
The value stored into the SDRAMC LPR register should be the current value of the register with the Self-refresh value set in the lower bit field. The bug involved only the Self-refresh value being written to the register, thus over writing any low-power ram settings. Signed-off-by: Humphrey Bucknell <hbucknell@saitek.com> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-09-01avr32: Fix lockup after Java stack underflow in user modeHaavard Skinnemoen
When using the Java Extension Module hardware, a Java stack underflow or overflow trap may cause the system to enter an infinite exception loop. Although there's no kernel support for the Java hardware yet, we need to be able to recover from this situation and keep the system running. This patch adds code to detect and fixup this situation in the critical exception handler and terminate the faulting process. We may have to rethink how to handle this more gracefully when the necessary kernel support for hardware-accelerated Java is added. Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-08-08avr32: Make atstk1006_nand_data definition staticHaavard Skinnemoen
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-08-08avr32: Reduce DataFlash bus speed to 8 MHz on ATNGW100Haavard Skinnemoen
Doing this in combination with "atmel_spi: fix hang due to missed interrupt" appears to eliminate the overruns I'm seeing when using JFFS2-on-DataFlash as /usr filesystem on the ATNGW100. Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-08-08avr32: Update defconfigsHaavard Skinnemoen
Enable power management, DMA and MMC on all boards except ATSTK1004, and add defconfig for the new ATSTK1006 board with NAND flash, UBI and UBIFS enabled as well. Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-08-08avr32: Clean up HMATRIX codeHaavard Skinnemoen
Introduce a few helper functions for HMATRIX configuration and clean up the register definitions. Also add definitions for the HMATRIX master and slave IDs on the AT32AP700x chips. Also make the definitions in hmatrix.h available to board code by moving it to <mach/hmatrix.h> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-08-08avr32: Add MMIO address definitions for certain controllersHaavard Skinnemoen
Hardcoded MMIO base addresses are used a few places throughout the platform code. Move these into the chip-specific header file so that adding support for new chips becomes a bit easier. Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-08-08avr32: Introduce <mach/chip.h>Haavard Skinnemoen
This file includes the appropriate chip-specific header with MMIO, IRQ and GPIO definitions used by the platform code. It may also be used to provide inline GPIO accessors for drivers that are willing to sacrifice portability for faster bitbanging. Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-08-08avr32: Remove include/asm-avr32/arch-at32apHaavard Skinnemoen
Since all users have been converted over to use <mach/foo.h>, there's no need for the arch-at32ap directory and associated symlink anymore. Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-08-05avr32: Use <mach/foo.h> instead of <asm/arch/foo.h>Haavard Skinnemoen
Update all avr32-specific files to use the new platform-specific header locations. Drivers shared with ARM are left alone for now. Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-08-05avr32: Introduce arch/avr32/mach-*/include/machHaavard Skinnemoen
Add arch/avr32/mach-*/include to include search path and copy all the files from include/asm/arch there. The old files will be removed once ARM does the same change and all common drivers are converted. Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-08-05avr32: Move include/asm-avr32 to arch/avr32/include/asmHaavard Skinnemoen
Leaving include/asm/arch alone for now. Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-07-27avr32: some mmc/sd cleanupsDavid Brownell
Minor cleanups for the MMC/SD support on avr32: - Make at32_add_device_mci() properly initialize "missing" platform data ... so boards like STK1002 won't try GPIO 0. - Switch over to gpio_is_valid() instead of testing for only one designated value. - Provide STK1002 platform data for the unlikely case that switches are set so first Ethernet controller isn't in use. (That's the only way to get card detect and writeprotect switch sensing on the STK1000.) And get rid of one "unused variable" warning. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-07-27Merge commit 'upstream/master'Haavard Skinnemoen
2008-07-26Merge git://git.infradead.org/mtd-2.6Linus Torvalds
* git://git.infradead.org/mtd-2.6: (57 commits) [MTD] [NAND] subpage read feature as a way to increase performance. CPUFREQ: S3C24XX NAND driver frequency scaling support. [MTD][NAND] au1550nd: remove unused variable [MTD] jedec_probe: Fix SST 16-bit chip detection [MTD][MTDPART] Fix a division by zero bug [MTD][MTDPART] Cleanup and document the erase region handling [MTD][MTDPART] Handle most checkpatch findings [MTD][MTDPART] Seperate main loop from per-partition code in add_mtd_partition [MTD] physmap: resume already suspended chips on failure to suspend [MTD] physmap: Fix suspend/resume/shutdown bugs. [MTD] [NOR] Fix -ETIMEO errors in CFI driver [MTD] [NAND] fsl_elbc_nand: fix section mismatch with CONFIG_MTD_OF_PARTS=y [JFFS2] Use .unlocked_ioctl [MTD] Fix const assignment in the MTD command line partitioning driver [MTD] [NOR] gen_probe: No debug message when debugging is disabled [MTD] [NAND] remove __PPC__ hardcoded address from DiskOnChip drivers [MTD] [MAPS] Remove the bast-flash driver. [MTD] [NAND] fsl_elbc_nand: ecclayout cleanups [MTD] [NAND] fsl_elbc_nand: implement support for flash-based BBT [MTD] [NAND] fsl_elbc_nand: fix OOB workability for large page NAND chips ...
2008-07-26avr32: use generic show_mem()Johannes Weiner
Remove arch-specific show_mem() in favor of the generic version. This also removes the following redundant information display: - free pages, printed by show_free_areas() - pages in slabs, printed by show_free_areas() - pages in swapcache, printed by show_swap_cache_info() where show_mem() calls show_free_areas(), which calls show_swap_cache_info(). Signed-off-by: Johannes Weiner <hannes@saeurebad.de> Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-25gpiolib: allow user-selectionMichael Buesch
This patch adds functionality to the gpio-lib subsystem to make it possible to enable the gpio-lib code even if the architecture code didn't request to get it built in. The archtitecture code does still need to implement the gpiolib accessor functions in its asm/gpio.h file. This patch adds the implementations for x86 and PPC. With these changes it is possible to run generic GPIO expansion cards on every architecture that implements the trivial wrapper functions. Support for more architectures can easily be added. Signed-off-by: Michael Buesch <mb@bu3sch.de> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: David Brownell <david-b@pacbell.net> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Jesper Nilsson <jesper.nilsson@axis.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Jean Delvare <khali@linux-fr.org> Cc: Samuel Ortiz <sameo@openedhand.com> Cc: Kumar Gala <galak@gate.crashing.org> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Adrian Bunk <bunk@stusta.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-25gpio: sysfs interfaceDavid Brownell
This adds a simple sysfs interface for GPIOs. /sys/class/gpio /export ... asks the kernel to export a GPIO to userspace /unexport ... to return a GPIO to the kernel /gpioN ... for each exported GPIO #N /value ... always readable, writes fail for input GPIOs /direction ... r/w as: in, out (default low); write high, low /gpiochipN ... for each gpiochip; #N is its first GPIO /base ... (r/o) same as N /label ... (r/o) descriptive, not necessarily unique /ngpio ... (r/o) number of GPIOs; numbered N .. N+(ngpio - 1) GPIOs claimed by kernel code may be exported by its owner using a new gpio_export() call, which should be most useful for driver debugging. Such exports may optionally be done without a "direction" attribute. Userspace may ask to take over a GPIO by writing to a sysfs control file, helping to cope with incomplete board support or other "one-off" requirements that don't merit full kernel support: echo 23 > /sys/class/gpio/export ... will gpio_request(23, "sysfs") and gpio_export(23); use /sys/class/gpio/gpio-23/direction to (re)configure it, when that GPIO can be used as both input and output. echo 23 > /sys/class/gpio/unexport ... will gpio_free(23), when it was exported as above The extra D-space footprint is a few hundred bytes, except for the sysfs resources associated with each exported GPIO. The additional I-space footprint is about two thirds of the current size of gpiolib (!). Since no /dev node creation is involved, no "udev" support is needed. Related changes: * This adds a device pointer to "struct gpio_chip". When GPIO providers initialize that, sysfs gpio class devices become children of that device instead of being "virtual" devices. * The (few) gpio_chip providers which have such a device node have been updated. * Some gpio_chip drivers also needed to update their module "owner" field ... for which missing kerneldoc was added. * Some gpio_chips don't support input GPIOs. Those GPIOs are now flagged appropriately when the chip is registered. Based on previous patches, and discussion both on and off LKML. A Documentation/ABI/testing/sysfs-gpio update is ready to submit once this merges to mainline. [akpm@linux-foundation.org: a few maintenance build fixes] Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de> Cc: Greg KH <greg@kroah.com> Cc: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-25Merge branch 'linux-next' of git://git.infradead.org/~dedekind/ubi-2.6David Woodhouse
2008-07-25avr32: allow system timer to share interrupt to make OProfile workVoss, Nikolaus
The following patch allows the avr32_comparator interrupt to be shared. This is necessary as the avr32 oprofile driver shares the irq group 0 with the timer. To make OProfile actually work on AVR32, a small patch for oprofiled is also needed (posted to the oprofile mailing list). Signed-off-by: Nikolaus Voss <n.voss@weinmann.de> [haavard.skinnemoen@atmel.com: set IRQF_SHARED unconditionally] Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-07-24Merge branch 'timers-fixes-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: nohz: adjust tick_nohz_stop_sched_tick() call of s390 as well nohz: prevent tick stop outside of the idle loop
2008-07-24Merge branch 'core-fixes-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: arch/mips/kernel/stacktrace.c: Heiko can't type kthread: reduce stack pressure in create_kthread and kthreadd fix core/stacktrace changes on avr32, mips, sh
2008-07-24PAGE_ALIGN(): correctly handle 64-bit values on 32-bit architecturesAndrea Righi
On 32-bit architectures PAGE_ALIGN() truncates 64-bit values to the 32-bit boundary. For example: u64 val = PAGE_ALIGN(size); always returns a value < 4GB even if size is greater than 4GB. The problem resides in PAGE_MASK definition (from include/asm-x86/page.h for example): #define PAGE_SHIFT 12 #define PAGE_SIZE (_AC(1,UL) << PAGE_SHIFT) #define PAGE_MASK (~(PAGE_SIZE-1)) ... #define PAGE_ALIGN(addr) (((addr)+PAGE_SIZE-1)&PAGE_MASK) The "~" is performed on a 32-bit value, so everything in "and" with PAGE_MASK greater than 4GB will be truncated to the 32-bit boundary. Using the ALIGN() macro seems to be the right way, because it uses typeof(addr) for the mask. Also move the PAGE_ALIGN() definitions out of include/asm-*/page.h in include/linux/mm.h. See also lkml discussion: http://lkml.org/lkml/2008/6/11/237 [akpm@linux-foundation.org: fix drivers/media/video/uvc/uvc_queue.c] [akpm@linux-foundation.org: fix v850] [akpm@linux-foundation.org: fix powerpc] [akpm@linux-foundation.org: fix arm] [akpm@linux-foundation.org: fix mips] [akpm@linux-foundation.org: fix drivers/media/video/pvrusb2/pvrusb2-dvb.c] [akpm@linux-foundation.org: fix drivers/mtd/maps/uclinux.c] [akpm@linux-foundation.org: fix powerpc] Signed-off-by: Andrea Righi <righi.andrea@gmail.com> Cc: <linux-arch@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-24bootmem: replace node_boot_start in struct bootmem_dataJohannes Weiner
Almost all users of this field need a PFN instead of a physical address, so replace node_boot_start with node_min_pfn. [Lee.Schermerhorn@hp.com: fix spurious BUG_ON() in mark_bootmem()] Signed-off-by: Johannes Weiner <hannes@saeureba.de> Cc: <linux-arch@vger.kernel.org> Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-24mm: drop unneeded pgdat argument from free_area_init_node()Johannes Weiner
free_area_init_node() gets passed in the node id as well as the node descriptor. This is redundant as the function can trivially get the node descriptor itself by means of NODE_DATA() and the node's id. I checked all the users and NODE_DATA() seems to be usable everywhere from where this function is called. Signed-off-by: Johannes Weiner <hannes@saeurebad.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-24add HAVE_CLK to Kconfig, for driver dependenciesDavid Brownell
Flag platforms as HAVE_CLK (or not) in Kconfig, based on whether they support <linux/clk.h> calls, so that otherwise portable drivers which need those calls can list that dependency. Something like this is a prerequisite for merging the musb_hdrc driver, currently used on platforms including Davinci, OMAP2430, OMAP3xx ... and the discrete TUSB6010 chip, which doesn't have a natural platform dependency. (Used with OMAP 2420 in current Nokia N8x0 tablets.) Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Russell King <rmk@arm.linux.org.uk> Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Paul Mundt <lethal@linux-sh.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-24avr32: Add platform data for AC97C platform deviceHans-Christian Egtvedt
This patch adds platform data to the AC97C platform device. This will let the board add a GPIO line which is connected to the external codecs reset line. The platform data, ac97c_platform_data, must also contain the DMA controller ID, RX channel ID and TX channel ID. Tested with Wolfson WM9712 and AP7000. Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-07-23Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (24 commits) I/OAT: I/OAT version 3.0 support I/OAT: tcp_dma_copybreak default value dependent on I/OAT version I/OAT: Add watchdog/reset functionality to ioatdma iop_adma: cleanup iop_chan_xor_slot_count iop_adma: document how to calculate the minimum descriptor pool size iop_adma: directly reclaim descriptors on allocation failure async_tx: make async_tx_test_ack a boolean routine async_tx: remove depend_tx from async_tx_sync_epilog async_tx: export async_tx_quiesce async_tx: fix handling of the "out of descriptor" condition in async_xor async_tx: ensure the xor destination buffer remains dma-mapped async_tx: list_for_each_entry_rcu() cleanup dmaengine: Driver for the Synopsys DesignWare DMA controller dmaengine: Add slave DMA interface dmaengine: add DMA_COMPL_SKIP_{SRC,DEST}_UNMAP flags to control dma unmap dmaengine: Add dma_client parameter to device_alloc_chan_resources dmatest: Simple DMA memcpy test client dmaengine: DMA engine driver for Marvell XOR engine iop-adma: fix platform driver hotplug/coldplug dmaengine: track the number of clients using a channel ... Fixed up conflict in drivers/dca/dca-sysfs.c manually