| Age | Commit message (Collapse) | Author |
|---|
|
Needed for followon patch
Signed-off-by: Andi Kleen <ak@suse.de>
|
|
- Introduce a wd_ops structure
- Convert the various nmi watchdogs over to it
- This allows to split the perfctr reservation from the watchdog
setup cleanly.
- Do perfctr reservation globally as it should have always been
- Remove dead code referenced only by unused EXPORT_SYMBOLs
Signed-off-by: Andi Kleen <ak@suse.de>
|
|
`ret_from_sys_call' label no longer exist and `syscall_exit' label was
introduced instead.
Signed-off-by: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Signed-off-by: Andi Kleen <ak@suse.de>
|
|
This patch just trivial converts from calling kernel_thread and daemonize
to just calling kthread_run.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
The locking of the xtime_lock around the cpu notifier is unessesary now.
At one time the tsc was used after a frequency change for timekeeping, but
the re-write of timekeeping no longer uses the TSC unless the frequency is
constant.
The variables that are changed in this section of code had also once been
used for timekeeping, but not any longer ..
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Currently the i386 architecture checks the family for mce capability and this
removes that and uses the CPUID information. Tested on a K8 revE and a
family10h processor.
This eliminates checking of a set AMD procesor family if mce is
allowed and relies on the information being in CPUID.
Signed-off-by: Joachim Deguara <joachim.deguara@amd.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Cleanup flush_tlb_others(), no functional change.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
IRQ is already disabled through local_irq_disable(). So
spin_lock_irqsave() can be replaced with spin_lock().
Signed-off-by: Hisashi Hifumi <hifumi.hisashi@oss.ntt.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Avoid checking for cpu gone in mm hot path when CONFIG_HOTPLUG_CPU is not
defined.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
startup_ipi_hook depends on CONFIG_X86_LOCAL_APIC, so move it to the
right part of the paravirt_ops initialization.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
|
|
Fix section mismatch warnings in mtrr code.
Fix line length on one source line.
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data: from .text.get_mtrr_state after 'get_mtrr_state' (at offset 0x103)
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.text: from .text.get_mtrr_state after 'get_mtrr_state' (at offset 0x180)
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.text: from .text.get_mtrr_state after 'get_mtrr_state' (at offset 0x199)
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.text: from .text.get_mtrr_state after 'get_mtrr_state' (at offset 0x1c1)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Use safe_apic_wait_icr_idle to check ICR idle bit if the vector is
NMI_VECTOR to avoid potential hangups in the event of crash when kdump
tries to stop the other CPUs.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
|
|
Implement __send_IPI_dest_field which can be used to send IPIs when the
"destination shorthand" field of the ICR is set to 00 (destination
field). Use it whenever possible.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
|
|
__inquire_remote_apic is used for APIC debugging, so use
safe_apic_wait_icr_idle instead of apic_wait_icr_idle to avoid possible
lockups when APIC delivery fails.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
|
|
The functionality provided by the new safe_apic_wait_icr_idle is being
open-coded all over "kernel/smpboot.c". Use safe_apic_wait_icr_idle
instead to consolidate code and ease maintenance.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
|
|
apic_wait_icr_idle looks like this:
static __inline__ void apic_wait_icr_idle(void)
{
while (apic_read(APIC_ICR) & APIC_ICR_BUSY)
cpu_relax();
}
The busy loop in this function would not be problematic if the
corresponding status bit in the ICR were always updated, but that does
not seem to be the case under certain crash scenarios. Kdump uses an IPI
to stop the other CPUs in the event of a crash, but when any of the
other CPUs are locked-up inside the NMI handler the CPU that sends the
IPI will end up looping forever in the ICR check, effectively
hard-locking the whole system.
Quoting from Intel's "MultiProcessor Specification" (Version 1.4), B-3:
"A local APIC unit indicates successful dispatch of an IPI by
resetting the Delivery Status bit in the Interrupt Command
Register (ICR). The operating system polls the delivery status
bit after sending an INIT or STARTUP IPI until the command has
been dispatched.
A period of 20 microseconds should be sufficient for IPI dispatch
to complete under normal operating conditions. If the IPI is not
successfully dispatched, the operating system can abort the
command. Alternatively, the operating system can retry the IPI by
writing the lower 32-bit double word of the ICR. This âtime-outâ
mechanism can be implemented through an external interrupt, if
interrupts are enabled on the processor, or through execution of
an instruction or time-stamp counter spin loop."
Intel's documentation suggests the implementation of a time-out
mechanism, which, by the way, is already being open-coded in some parts
of the kernel that tinker with ICR.
Create a apic_wait_icr_idle replacement that implements the time-out
mechanism and that can be used to solve the aforementioned problem.
AK: moved both functions out of line
AK: added improved loop from Keith Owens
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
|
|
If our copy of the MTRRs of the BSP has RdMem or WrMem set, and
we are running on an AMD64/K8 system, the boot CPU must have had
MtrrFixDramEn and MtrrFixDramModEn set (otherwise our RDMSR would
have copied these bits cleared), so we set them on this CPU as well.
This allows us to keep the AMD64/K8 RdMem and WrMem bits in sync
across the CPUs of SMP systems in order to fullfill the duty of
system software to "initialize and maintain MTRR consistency
across all processors." as written in the AMD and Intel manuals.
If an WRMSR instruction fails because MtrrFixDramModEn is not
set, I expect that also the Intel-style MTRR bits are not updated.
AK: minor cleanup, moved MSR defines around
Signed-off-by: Bernhard Kaindl <bk@suse.de>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andi Kleen <ak@suse.de>
Cc: Dave Jones <davej@codemonkey.org.uk>
|
|
Note: This patch didn'nt need an update since it's initial post.
Some BIOSes may modify fixed-range MTRRs in SMM, e.g. when they
transition the system into ACPI mode, which is entered thru an SMI,
triggered by Linux in acpi_enable().
SMIs which cause that Linux is interrupted and BIOS code is
executed (which may change e.g. fixed-range MTRRs) in SMM may
be raised by an embedded system controller which is often found
in notebooks also at other occasions.
If we would not update our copy of the fixed-range MTRRs before
suspending to RAM or to disk, restore_processor_state() would
set the fixed-range MTRRs of the BSP using old backup values
which may be outdated and this could cause the system to fail
later during resume.
This patch ensures that our copy of the fixed-range MTRRs
is updated when saving the boot processor state on suspend
to disk and suspend to RAM.
In combination with other patches this allows to fix s2ram
and s2disk on the Acer Ferrari 1000 notebook and at least
s2disk on the Acer Ferrari 5000 notebook.
Signed-off-by: Bernhard Kaindl <bk@suse.de>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andi Kleen <ak@suse.de>
Cc: Dave Jones <davej@codemonkey.org.uk>
|
|
Applied fix by Andew Morton:
http://lkml.org/lkml/2007/4/8/88 - Fix `make headers_check'.
AMD and Intel x86 CPU manuals state that it is the responsibility of
system software to initialize and maintain MTRR consistency across
all processors in Multi-Processing Environments.
Quote from page 188 of the AMD64 System Programming manual (Volume 2):
7.6.5 MTRRs in Multi-Processing Environments
"In multi-processing environments, the MTRRs located in all processors must
characterize memory in the same way. Generally, this means that identical
values are written to the MTRRs used by the processors." (short omission here)
"Failure to do so may result in coherency violations or loss of atomicity.
Processor implementations do not check the MTRR settings in other processors
to ensure consistency. It is the responsibility of system software to
initialize and maintain MTRR consistency across all processors."
Current Linux MTRR code already implements the above in the case that the
BIOS does not properly initialize MTRRs on the secondary processors,
but the case where the fixed-range MTRRs of the boot processor are changed
after Linux started to boot, before the initialsation of a secondary
processor, is not handled yet.
In this case, secondary processors are currently initialized by Linux
with MTRRs which the boot processor had very early, when mtrr_bp_init()
did run, but not with the MTRRs which the boot processor uses at the
time when that secondary processors is actually booted,
causing differing MTRR contents on the secondary processors.
Such situation happens on Acer Ferrari 1000 and 5000 notebooks where the
BIOS enables and sets AMD-specific IORR bits in the fixed-range MTRRs
of the boot processor when it transitions the system into ACPI mode.
The SMI handler of the BIOS does this in SMM, entered while Linux ACPI
code runs acpi_enable().
Other occasions where the SMI handler of the BIOS may change bits in
the MTRRs could occur as well. To initialize newly booted secodary
processors with the fixed-range MTRRs which the boot processor uses
at that time, this patch saves the fixed-range MTRRs of the boot
processor before new secondary processors are started. When the
secondary processors run their Linux initialisation code, their
fixed-range MTRRs will be updated with the saved fixed-range MTRRs.
If CONFIG_MTRR is not set, we define mtrr_save_state
as an empty statement because there is nothing to do.
Possible TODOs:
*) CPU-hotplugging outside of SMP suspend/resume is not yet tested
with this patch.
*) If, even in this case, an AP never runs i386/do_boot_cpu or x86_64/cpu_up,
then the calls to mtrr_save_state() could be replaced by calls to
mtrr_save_fixed_ranges(NULL) and mtrr_save_state() would not be
needed.
That would need either verification of the CPU-hotplug code or
at least a test on a >2 CPU machine.
*) The MTRRs of other running processors are not yet checked at this
time but it might be interesting to syncronize the MTTRs of all
processors before booting. That would be an incremental patch,
but of rather low priority since there is no machine known so
far which would require this.
AK: moved prototypes on x86-64 around to fix warnings
Signed-off-by: Bernhard Kaindl <bk@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Cc: Dave Jones <davej@codemonkey.org.uk>
|
|
In this current implementation which is used in other patches,
mtrr_save_fixed_ranges() accepts a dummy void pointer because
in the current implementation of one of these patches, this
function may be called from smp_call_function_single() which
requires that this function takes a void pointer argument.
This function calls get_fixed_ranges(), passing mtrr_state.fixed_ranges
which is the element of the static struct which stores our current
backup of the fixed-range MTRR values which all CPUs shall be
using.
Because mtrr_save_fixed_ranges calls get_fixed_ranges after
kernel initialisation time, __init needs to be removed from
the declaration of get_fixed_ranges().
If CONFIG_MTRR is not set, we define mtrr_save_fixed_ranges
as an empty statement because there is nothing to do.
AK: Moved prototypes for x86-64 around to fix warnings
Signed-off-by: Bernhard Kaindl <bk@suse.de>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andi Kleen <ak@suse.de>
Cc: Dave Jones <davej@codemonkey.org.uk>
|
|
Three cleanups:
1: ELF notes are never mapped, so there's no need to have any access
flags in their phdr.
2: When generating them from asm, tell the assembler to use a SHT_NOTE
section type. There doesn't seem to be a way to do this from C.
3: Use ANSI rather than traditional cpp behaviour to stringify the
macro argument.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Eric W. Biederman <ebiederm@xmission.com>
|
|
Otherwise non GPL modules cannot even do basic operations
like disabling interrupts anymore, which would be excessive.
Longer term should split the single structure up into
internal and external symbols and not export the internal
ones at all.
Signed-off-by: Andi Kleen <ak@suse.de>
|
|
The other symbols used to delineate the alt-instructions sections have the
form __foo/__foo_end. Rename parainstructions to match.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Convert VMI timer to use clock events, making it properly able to use the NO_HZ
infrastructure. On UP systems, with no local APIC, we just continue to route
these events through the PIT. On systems with a local APIC, or SMP, we provide
a single source interrupt chip which creates the local timer IRQ. It actually
gets delivered by the APIC hardware, but we don't want to use the same local
APIC clocksource processing, so we create our own handler here.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andi Kleen <ak@suse.de>
CC: Dan Hecht <dhecht@vmware.com>
CC: Ingo Molnar <mingo@elte.hu>
CC: Thomas Gleixner <tglx@linutronix.de>
|
|
Implement vmi_kmap_atomic_pte in terms of the backend set_linear_mapping
operation. The conversion is rather straighforward; call kmap_atomic
and then inform the hypervisor of the page mapping.
The _flush_tlb damage is due to macros being pulled in from highmem.h.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andi Kleen <ak@suse.de>
|
|
configurations.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andi Kleen <ak@suse.de>
|
|
No, just no. You do not use goto to skip a code block. You do not
return an obvious variable from a singly-inlined function and give
the function a return value. You don't put unexplained comments
about kmalloc in code which doesn't do dynamic allocation. And
you don't leave stray warnings around for no good reason.
Also, when possible, it is better to use block scoped variables
because gcc can sometime generate better code.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andi Kleen <ak@suse.de>
|
|
Add "noreplace-paravirt" to disable paravirt_ops patching.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andi Kleen <ak@suse.de>
|
|
head.S creates the very initial pagetable for the kernel. This just
maps enough space for the kernel itself, and an allocation bitmap.
The amount of mapped memory is rounded up to 4Mbytes, and so this
typically ends up mapping 8Mbytes of memory.
When booting, pagetable_init() needs to create mappings for all
lowmem, and the pagetables for these mappings are allocated from the
free pages around the kernel in low memory. If the number of
pagetable pages + kernel size exceeds head.S's initial mapping, it
will end up faulting on an unmapped page. This will only happen with
specific combinations of kernel size and memory size.
This patch makes sure that head.S also maps enough space to fit the
kernel pagetables as well as the kernel itself. It ends up using an
additional two pages of unreclaimable memory.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Zachary Amsden <zach@vmware.com>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>,
|
|
Fixes two problems with the GDT when compiling for uniprocessor:
- There's no percpu segment, so trying to load its selector into %fs fails.
Use a null selector instead.
- The real gdt needs to be loaded at some point. Do it in cpu_init().
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
|
|
Currently x86 (similar to x84-64) has a special per-cpu structure
called "i386_pda" which can be easily and efficiently referenced via
the %fs register. An ELF section is more flexible than a structure,
allowing any piece of code to use this area. Indeed, such a section
already exists: the per-cpu area.
So this patch:
(1) Removes the PDA and uses per-cpu variables for each current member.
(2) Replaces the __KERNEL_PDA segment with __KERNEL_PERCPU.
(3) Creates a per-cpu mirror of __per_cpu_offset called this_cpu_off, which
can be used to calculate addresses for this CPU's variables.
(4) Simplifies startup, because %fs doesn't need to be loaded with a
special segment at early boot; it can be deferred until the first
percpu area is allocated (or never for UP).
The result is less code and one less x86-specific concept.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
|
|
Xen wants a dedicated page for the GDT. I believe VMI likes it too.
lguest, KVM and native don't care.
Simple transformation to page-aligned "struct gdt_page".
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Jeremy Fitzhardinge <jeremy@xensource.com>
|
|
inflate_fixed and huft_build together use around 2.7k of stack. When
using 4k stacks, I saw stack overflows from interrupts arriving while
unpacking the root initrd:
do_IRQ: stack overflow: 384
[<c0106b64>] show_trace_log_lvl+0x1a/0x30
[<c01075e6>] show_trace+0x12/0x14
[<c010763f>] dump_stack+0x16/0x18
[<c0107ca4>] do_IRQ+0x6d/0xd9
[<c010202b>] xen_evtchn_do_upcall+0x6e/0xa2
[<c0106781>] xen_hypervisor_callback+0x25/0x2c
[<c010116c>] xen_restore_fl+0x27/0x29
[<c0330f63>] _spin_unlock_irqrestore+0x4a/0x50
[<c0117aab>] change_page_attr+0x577/0x584
[<c0117b45>] kernel_map_pages+0x8d/0xb4
[<c016a314>] cache_alloc_refill+0x53f/0x632
[<c016a6c2>] __kmalloc+0xc1/0x10d
[<c0463d34>] malloc+0x10/0x12
[<c04641c1>] huft_build+0x2a7/0x5fa
[<c04645a5>] inflate_fixed+0x91/0x136
[<c04657e2>] unpack_to_rootfs+0x5f2/0x8c1
[<c0465acf>] populate_rootfs+0x1e/0xe4
(This was under Xen, but there's no reason it couldn't happen on bare
hardware.)
This patch mallocs the local variables, thereby reducing the stack
usage to sane levels.
Also, up the heap size for the kernel decompressor to deal with the
extra allocation.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Tim Yamin <plasmaroo@gentoo.org>
Cc: Andi Kleen <ak@suse.de>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
|
|
In shadow mode hypervisors, ptep_get_and_clear achieves the desired
purpose of keeping the shadows in sync by issuing a native_get_and_clear,
followed by a call to pte_update, which indicates the PTE has been
modified.
Direct mode hypervisors (Xen) have no need for this anyway, and will trap
the update using writable pagetables.
This means no hypervisor makes use of ptep_get_and_clear; there is no
reason to have it in the paravirt-ops structure. Change confusing
terminology about raw vs. native functions into consistent use of
native_pte_xxx for operations which do not invoke paravirt-ops.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andi Kleen <ak@suse.de>
|
|
kunmap_atomic should flush any pending lazy mmu updates, mainly to be
consistent with kmap_atomic, and to preserve its normal behaviour.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
|
|
Xen and VMI both have special requirements when mapping a highmem pte
page into the kernel address space. These can be dealt with by adding
a new kmap_atomic_pte() function for mapping highptes, and hooking it
into the paravirt_ops infrastructure.
Xen specifically wants to map the pte page RO, so this patch exposes a
helper function, kmap_atomic_prot, which maps the page with the
specified page protections.
This also adds a kmap_flush_unused() function to clear out the cached
kmap mappings. Xen needs this to clear out any potential stray RW
mappings of pages which will become part of a pagetable.
[ Zach - vmi.c will need some attention after this patch. It wasn't
immediately obvious to me what needs to be done. ]
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Zachary Amsden <zach@vmware.com>
|
|
Back out the map_pt_hook to clear the way for kmap_atomic_pte.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Zachary Amsden <zach@vmware.com>
|
|
This patch adds a pv_op for flush_tlb_others. Linux running on native
hardware uses cross-CPU IPIs to flush the TLB on any CPU which may
have a particular mm's pagetable entries cached in its TLB. This is
inefficient in a paravirtualized environment, since the hypervisor
knows which real CPUs actually contain cached mappings, which may be a
small subset of a guest's VCPUs.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
|
|
Implement the actual patching machinery. paravirt_patch_default()
contains the logic to automatically patch a callsite based on a few
simple rules:
- if the paravirt_op function is paravirt_nop, then patch nops
- if the paravirt_op function is a jmp target, then jmp to it
- if the paravirt_op function is callable and doesn't clobber too much
for the callsite, call it directly
paravirt_patch_default is suitable as a default implementation of
paravirt_ops.patch, will remove most of the expensive indirect calls
in favour of either a direct call or a pile of nops.
Backends may implement their own patcher, however. There are several
helper functions to help with this:
paravirt_patch_nop nop out a callsite
paravirt_patch_ignore leave the callsite as-is
paravirt_patch_call patch a call if the caller and callee
have compatible clobbers
paravirt_patch_jmp patch in a jmp
paravirt_patch_insns patch some literal instructions over
the callsite, if they fit
This patch also implements more direct patches for the native case, so
that when running on native hardware many common operations are
implemented inline.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Zachary Amsden <zach@vmware.com>
Cc: Anthony Liguori <anthony@codemonkey.ws>
Acked-by: Ingo Molnar <mingo@elte.hu>
|
|
Fix a few clobbers to include the return register. The clobbers set
is the set of all registers modified (or may be modified) by the code
snippet, regardless of whether it was deliberate or accidental.
Also, make sure that callsites which are used in contexts which don't
allow clobbers actually save and restore all clobberable registers.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Zachary Amsden <zach@vmware.com>
|
|
paravirt_ops structure
Use patch type identifiers derived from the offset of the operation in
the paravirt_ops structure. This avoids having to maintain a separate
enum for patch site types.
Also, since the identifier is derived from the offset into
paravirt_ops, the offset can be derived from the identifier. This is
used to remove replicated information in the various callsite macros,
which has been a source of bugs in the past.
This patch also drops the fused save_fl+cli operation, which doesn't
really add much and makes things more complex - specifically because
it breaks the 1:1 relationship between identifiers and offsets. If
this operation turns out to be particularly beneficial, then the right
answer is to define a new entrypoint for it.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Zachary Amsden <zach@vmware.com>
|
|
for clarity
Rename struct paravirt_patch to paravirt_patch_site, so that it
clearly refers to a callsite, and not the patch which may be applied
to that callsite.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Zachary Amsden <zach@vmware.com>
|
|
Add hooks to allow a paravirt implementation to track the lifetime of
an mm. Paravirtualization requires three hooks, but only two are
needed in common code. They are:
arch_dup_mmap, which is called when a new mmap is created at fork
arch_exit_mmap, which is called when the last process reference to an
mm is dropped, which typically happens on exit and exec.
The third hook is activate_mm, which is called from the arch-specific
activate_mm() macro/function, and so doesn't need stub versions for
other architectures. It's called when an mm is first used.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: linux-arch@vger.kernel.org
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
|
|
Normally when running in PAE mode, the 4th PMD maps the kernel address space,
which can be shared among all processes (since they all need the same kernel
mappings).
Xen, however, does not allow guests to have the kernel pmd shared between page
tables, so parameterize pgtable.c to allow both modes of operation.
There are several side-effects of this. One is that vmalloc will update the
kernel address space mappings, and those updates need to be propagated into
all processes if the kernel mappings are not intrinsically shared. In the
non-PAE case, this is done by maintaining a pgd_list of all processes; this
list is used when all process pagetables must be updated. pgd_list is
threaded via otherwise unused entries in the page structure for the pgd, which
means that the pgd must be page-sized for this to work.
Normally the PAE pgd is only 4x64 byte entries large, but Xen requires the PAE
pgd to page aligned anyway, so this patch forces the pgd to be page
aligned+sized when the kernel pmd is unshared, to accomodate both these
requirements.
Also, since there may be several distinct kernel pmds (if the user/kernel
split is below 3G), there's no point in allocating them from a slab cache;
they're just allocated with get_free_page and initialized appropriately. (Of
course the could be cached if there is just a single kernel pmd - which is the
default with a 3G user/kernel split - but it doesn't seem worthwhile to add
yet another case into this code).
[ Many thanks to wli for review comments. ]
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: William Lee Irwin III <wli@holomorphy.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Zachary Amsden <zach@vmware.com>
Cc: Christoph Lameter <clameter@sgi.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
This patch introduces paravirt_ops hooks to control how the kernel's
initial pagetable is set up.
In the case of a native boot, the very early bootstrap code creates a
simple non-PAE pagetable to map the kernel and physical memory. When
the VM subsystem is initialized, it creates a proper pagetable which
respects the PAE mode, large pages, etc.
When booting under a hypervisor, there are many possibilities for what
paging environment the hypervisor establishes for the guest kernel, so
the constructon of the kernel's pagetable depends on the hypervisor.
In the case of Xen, the hypervisor boots the kernel with a fully
constructed pagetable, which is already using PAE if necessary. Also,
Xen requires particular care when constructing pagetables to make sure
all pagetables are always mapped read-only.
In order to make this easier, kernel's initial pagetable construction
has been changed to only allocate and initialize a pagetable page if
there's no page already present in the pagetable. This allows the Xen
paravirt backend to make a copy of the hypervisor-provided pagetable,
allowing the kernel to establish any more mappings it needs while
keeping the existing ones.
A slightly subtle point which is worth highlighting here is that Xen
requires all kernel mappings to share the same pte_t pages between all
pagetables, so that updating a kernel page's mapping in one pagetable
is reflected in all other pagetables. This makes it possible to
allocate a page and attach it to a pagetable without having to
explicitly enumerate that page's mapping in all pagetables.
And:
+From: "Eric W. Biederman" <ebiederm@xmission.com>
If we don't set the leaf page table entries it is quite possible that
will inherit and incorrect page table entry from the initial boot
page table setup in head.S. So we need to redo the effort here,
so we pick up PSE, PGE and the like.
Hypervisors like Xen require that their page tables be read-only,
which is slightly incompatible with our low identity mappings, however
I discussed this with Jeremy he has modified the Xen early set_pte
function to avoid problems in this area.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: William Irwin <bill.irwin@oracle.com>
Cc: Ingo Molnar <mingo@elte.hu>
|
|
entries
Add a set of accessors to pack, unpack and modify page table entries
(at all levels). This allows a paravirt implementation to control the
contents of pgd/pmd/pte entries. For example, Xen uses this to
convert the (pseudo-)physical address into a machine address when
populating a pagetable entry, and converting back to pphys address
when an entry is read.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
|
|
Add a _paravirt_nop function for use as a stub for no-op operations,
and paravirt_nop #defined void * version to make using it easier
(since all its uses are as a void *).
This is useful to allow the patcher to automatically identify noop
operations so it can simply nop out the callsite.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
[mingo] but only as a cleanup of the current open-coded (void *) casts.
My problem with this is that it loses the types. Not that there is much
to check for, but still, this adds some assumptions about how function
calls look like
|
|
Remove CONFIG_DEBUG_PARAVIRT. When inlining code, this option
attempts to trash registers in the patch-site's "clobber" field, on
the grounds that this should find bugs with incorrect clobbers.
Unfortunately, the clobber field really means "registers modified by
this patch site", which includes return values.
Because of this, this option has outlived its usefulness, so remove
it.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
|
|
On Thu, 2007-03-29 at 13:16 +0200, Andi Kleen wrote:
> Please clean it up properly with two structs.
Not sure about this, now I've done it. Running it here.
If you like it, I can do x86-64 as well.
==
lguest defines its own TSS struct because the "struct tss_struct"
contains linux-specific additions. Andi asked me to split the struct
in processor.h.
Unfortunately it makes usage a little awkward.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andi Kleen <ak@suse.de>
|
