| Age | Commit message (Collapse) | Author |
|---|
|
|
|
XPC calls smp_processor_id() twice from xpc_setup_infrastructure() with
preemption enabled, which gets flagged if 'DEBUG_PREEMPT=y'. This patch
replaces the two calls to smp_processor_id() by a single call to
raw_smp_processor_id() since any CPU within the partition will do.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
The Altix subarch does not provide node information via ACPI. Instead hooks
are used to fixup pci structures. This patch determines the nodes for Altix
PCI busses.
Remote Bridges:
---------------
Altix supports remote I/O nodes without memory or processors but with bridges.
The TIOCA type of bridge is an AGP bridge and the PROM provides information
about the closest node. That information will be returned by pcibus_to_node.
The TIOCP remote bridge type is a PCI bridge but the PROM does not provide a
closest node id. pcibus_to_node will return -1 for devices on those bridges
meaning that device control structures may be allocated on any node.
Safeguard:
----------
Should the fixups result in invalid node information for a pci controller then
a warning will be printed and pcibus_to_node will return -1.
This patch also fixes the "FIXME" in sn_dma_alloc_coherent. This means that
dma_alloc_coherent will now use alloc_pages_node to allocate memory local to
the node that the PCI device is connected to.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
Check with PAL to see what the i-cache line size is for
each level of the cache, and so use the correct stride
when flushing the cache.
Acked-by: David Mosberger
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
This patch removes the CONFIG_IA64_SGI_SN_SIM option entirely, allowing
any kernel bootable on sn2 to also be booted in the simulator.
Boot tested on Altix and HP rx2600.
Signed-off-by: Greg Edwards <edwardsg@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
|
|
pcibus_to_node provides a way for the Linux kernel to identify to which
node a certain pcibus connects to. Allocations of control structures
for devices can then be made on the node where the pci bus is located
to allow local access during interrupt and other device manipulation.
This patch provides a new "node" field in the the pci_controller
structure. The node field will be set based on ACPI information (thanks
to Alex Williamson <alex.williamson@hp.com for that piece).
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
http://bugzilla.kernel.org/show_bug.cgi?id=4233
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Create a new top-level menu named "Networking" thus moving
net related options and protocol selection way from the drivers
menu and up on the top-level where they belong.
To implement this all architectures has to source "net/Kconfig" before
drivers/*/Kconfig in their Kconfig file. This change has been
implemented for all architectures.
Device drivers for ordinary NIC's are still to be found
in the Device Drivers section, but Bluetooth, IrDA and ax25
are located with their corresponding menu entries under the new
networking menu item.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ACPI 3.0 added a Correctable Platform Error Interrupt (CPEI)
Processor Overide flag to MADT.Platform_Interrupt_Source.
Record the processor that was provided as hint from ACPI.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Current assign_irq_vector() will panic if interrupt vectors is running
out. But I think how to handle the case of lack of interrupt vectors
should be handled by the caller of this function. For example, some
PCI devices can raise the interrupt signal via both MSI and I/O
APIC. So even if the driver for these device fails to allocate a
vector for MSI, the driver still has a chance to use I/O APIC based
interrupt. But currently there is no chance for these driver to use
I/O APIC based interrupt because kernel will panic when
assign_irq_vector() fails to allocate interrupt vector.
The following patch changes assign_irq_vector() for ia64 to return
-ENOSPC on error instead of panic (as i386 and x86_64 versions do).
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
Description: Replace schedule_timeout() with msleep_interruptible() to
guarantee the task delays as expected.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Acked-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
changing CONFIG_LOCALVERSION rebuilds too much, for no appearent reason.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
Both 2.4 and 2.6 kernels need this patch for the next binutils.
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
Disable the tiocx driver on non-SN systems.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
Jesse Barnes provided the original version of this patch months ago, but
other changes kept conflicting with it, so it got deferred. Greg Edwards
dug it out of obscurity just over a week ago, and almost immediately
another conflicting patch appeared (Bob Picco's memory-less nodes).
I've resolved the conflicts and got it running again. CONFIG_SGI_TIOCX
is set to "y" in defconfig, which causes a Tiger to not boot (oops in
tiocx_init). But that can be resolved later ... get this in now before it
gets stale again.
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
I reworked how nodes with only CPUs are treated. The patch below seems
simpler to me and has eliminated the complicated routine
reassign_cpu_only_nodes. There isn't any longer the requirement
to modify ACPI NUMA information which was in large part the
complexity introduced in reassign_cpu_only_nodes.
This patch will produce a different number of nodes. For example,
reassign_cpu_only_nodes would reduce two CPUonly nodes and one memory node
configuration to one memory+CPUs node configuration. This patch
doesn't change the number of nodes which means the user will see three. Two
nodes without memory and one node with all the memory.
While doing this patch, I noticed that early_nr_phys_cpus_node isn't serving
any useful purpose. It is called once in find_pernode_space but the value
isn't used to computer pernode space.
Signed-off-by: bob.picco <bob.picco@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
|
|
restore_sigcontext calls ia64_set_local_fpu_owner() which requires that
preempt be disabled.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
This patch is the SGI hotplug driver and additional changes required for
the driver. These modifications include changes to the SN io_init.c code
for memory management, the inclusion of new SAL calls to enable and disable
PCI slots, and a hotplug-style driver.
Signed-off-by: Prarit Bhargava <prarit@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
This patch is a rewrite of the code to check the PROM version. The current
code has some deficiences in the way PROM comparisons were made. The minimum
value of PROM that will boot has also been changed to 4.04.
Signed-off-by: Prarit Bhargava <prarit@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
This patch moves header files out of the arch/ia64/sn directories and into
include/asm-ia64/sn. These files were being included by other subsystems
and should be under include/asm-ia64/sn.
Signed-off-by: Prarit Bhargava <prarit@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
This patch fixes the SN IRQ code such that cpu affinity and
Hotplug can modify IRQ values. The sn_irq_info structures are now locked
using a RCU lock mechanism to avoid lock contention in the lost interrupt
WAR code.
Signed-off-by: Prarit Bhargava <prarit@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
The following renames arch_init, a kprobes function for performing any
architecture specific initialization, to arch_init_kprobes in order to
cleanup the namespace.
Also, this patch adds arch_init_kprobes to sparc64 to fix the sparc64 kprobes
build from the last return probe patch.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
|
|
There's another problem shown up by Ingo's recent patch to make
smp_processor_id() complain if it's called with preemption enabled.
local_finish_flush_tlb_mm() calls activate_context() in a situation
where it could be rescheduled to another processor. This patch
disables preemption around the call.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
Patch makes it possible to use the "F4" function key to do
magic sysrq in the HP Ski simulator.
Signed-off-by: David Mosberger-Tang <davidm@hpl.hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
This patch fixes an ordering issue between the init code for the
tiocx bus driver and tiocx-related device drivers. Also adds
a new brick to the list of known FPGA bricks.
Signed-off-by: Bruce Losure <blosure@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
This patch is a sparse compile cleanup of tioca_provider.c, sn_hwperf.h, and
tioca_provider.h. Each of these files had sparse warnings when
compiled.
Signed-off-by: Prarit Bhargava <prarit@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
This patch changes some macros that are used when running kernel on the
SGI simulator.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
This patch is a sparse compile cleanup of shub_mmr.h using both the defconfig
and the sn2_defconfig config files.
The issue with this file was the missing usage of __IA64_UL_CONST wrapper.
This wrapper is defined in include/asm-ia64/types.h and wraps a long
constant definition with UL or with nothing depending on its usage in the
kernel. The missing wrapper caused many sparse compile errors like
warning: constant 0x0x0000000010000380 so big it is long
Signed-off-by: Prarit Bhargava <prarit@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
This patch greatly speeds up the handling of lfetch.fault instructions
which result in NaT consumption. Due to the NaT-page mapped at address
0, this is guaranteed to happen when lfetch.fault'ing a NULL pointer.
With this patch in place, we can even define prefetch()/prefetchw() as
lfetch.fault without significant performance degradation. More
importantly, it allows compilers to be more aggressive with using
lfetch.fault on pointers that might be NULL.
Signed-off-by: David Mosberger-Tang <davidm@hpl.hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
No functional change, just identify the device nicely:
-IOC: Unknown (103c:12ec) 0.1 HPA 0xf8020002000 IOVA space 1024Mb at 0x40000000
+IOC: sx2000 0.1 HPA 0xf8020002000 IOVA space 1024Mb at 0x40000000
We used to create fake PCI devices for these chips, but we no longer do that.
So I don't think there's any reason to touch pci_ids.h now.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
Altix patch to enable use of vgacon driver on that platform. Depends on the
PCDP generalization patch discussed at:
http://marc.theaimsgroup.com/?l=linux-ia64&m=111446235101939&w=2
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
Resend 2 with changes per Bjorn Helgaas comments. Changes from original:
+ Change globals to vga_console_iobase/vga_console_membase and make them
unconditional.
+ Address style-related comments.
Patch to extend the PCDP vga setup code to support PCI io/mem translations
for the legacy vga ioport and ram spaces on architectures (e.g. altix) which
need them.
Summary of the changes:
drivers/firmware/pcdp.c
drivers/firmware/pcdp.h
-----------------------
+ add declaration for the spec-defined PCI interface struct (pcdp_if_pci)
as well as support macros.
+ extend setup_vga_console() to know about pcdp_if_pci and add a couple of
globals to hold the io and mem translation offsets if present.
arch/ia64/kernel/setup.c
------------------------
+ tweek early_console_setup() to allow multiple early console setup routines
to be called.
include/asm-ia64/vga.h
----------------------
+ make VGA_MAP_MEM vga_console_membase aware
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
|
|
|
|
This is an ia64 implementation of acpi_register_ioapic() and
acpi_unregister_ioapic() interfaces.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch adds the following new interfaces for I/O xAPIC
hotplug. The implementation of these interfaces depends on each
architecture.
o int acpi_register_ioapic(acpi_handle handle, u64 phys_addr,
u32 gsi_base);
This new interface is to add a new I/O xAPIC specified by
phys_addr and gsi_base pair. phys_addr is the physical address
to which the I/O xAPIC is mapped and gsi_base is global system
interrupt base of the I/O xAPIC. acpi_register_ioapic returns
0 on success, or negative value on error.
o int acpi_unregister_ioapic(acpi_handle handle, u32 gsi_base);
This new interface is to remove a I/O xAPIC specified by
gsi_base. acpi_unregister_ioapic returns 0 on success, or
negative value on error.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Read bridge io/mem/pfmem ranges when fixing up the bus so that bus resources
are tracked. This is required to properly support pci end device and bridge
hotplug.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
PCI scan code calls the arch specific pcibios_fixup_bus() each time it scans a
new bridge. For root bridge hot-plug, the bridge and it's attached devices
may not have been configured properly yet, so it's not safe to claim those
resources at this time.
This code goes away when we clean up the way pci resources are claimed (in
pci_enable_device()), so this is only a stopgap fix.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
When checking if a PCI to PCI bridge should be enabled to decode memory and/or
IO resources, we need to look at all device resources not just the first 6.
This is needed to allow PCI bridges to pass down memory and IO accesses to
child devices even when the bridge itself does not consume resources in its
PCI BARs.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
When you hot-plug a (root) bridge hierarchy, it may have p2p bridges and
devices attached to it that have not been configured by firmware. In this
case, we need to configure the devices before starting them. This patch
separates device start from device scan so that we can introduce the
configuration step in the middle.
I kept the existing semantics for pci_scan_bus() since there are a huge number
of callers to that function.
Also, I have no way of testing the changes I made to the parisc files, so this
needs review by those folks. Sorry for the massive cross-post, this touches
files in many different places.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Not safe to insert kprobes on IVT code.
This patch checks to see if the address on which Kprobes is being inserted is
in ivt code and if it is in ivt code then refuse to register kprobe.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Acked-by: David Mosberger <davidm@napali.hpl.hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Without the ability to atomically write 16 bytes, we can not update the
middle slot of a bundle, slot 1, unless we stop the machine first. This
patch will ensure the ability to robustly insert and remove a kprobe by
refusing to insert a kprobe on slot 1 until a mechanism is in place to
safely handle this case.
Signed-off-by: Rusty Lynch <rusty.lynch@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The following patch implements function return probes for ia64 using
the revised design. With this new design we no longer need to do some
of the odd hacks previous required on the last ia64 return probe port
that I sent out for comments.
Note that this new implementation still does not resolve the problem noted
by Keith Owens where backtrace data is lost after a return probe is hit.
Changes include:
* Addition of kretprobe_trampoline to act as a dummy function for instrumented
functions to return to, and for the return probe infrastructure to place
a kprobe on on, gaining control so that the return probe handler
can be called, and so that the instruction pointer can be moved back
to the original return address.
* Addition of arch_init(), allowing a kprobe to be registered on
kretprobe_trampoline
* Addition of trampoline_probe_handler() which is used as the pre_handler
for the kprobe inserted on kretprobe_implementation. This is the function
that handles the details for calling the return probe handler function
and returning control back at the original return address
* Addition of arch_prepare_kretprobe() which is setup as the pre_handler
for a kprobe registered at the beginning of the target function by
kernel/kprobes.c so that a return probe instance can be setup when
a caller enters the target function. (A return probe instance contains
all the needed information for trampoline_probe_handler to do it's job.)
* Hooks added to the exit path of a task so that we can cleanup any left-over
return probe instances (i.e. if a task dies while inside a targeted function
then the return probe instance was reserved at the beginning of the function
but the function never returns so we need to mark the instance as unused.)
Signed-off-by: Rusty Lynch <rusty.lynch@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
