| Age | Commit message (Collapse) | Author |
|---|
|
Op_model_cell supports native Cell. By returning -EINVAL, oprofile
uses timer interrupt on Cell LPAR.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
A few code paths need to check whether or not they are running
on the PS3's LV1 hypervisor before making hcalls. This introduces
a new firmware feature bit for this, FW_FEATURE_PS3_LV1.
Now when both PS3 and IBM_CELL_BLADE are enabled, but not PSERIES,
FW_FEATURE_PS3_LV1 and FW_FEATURE_LPAR get enabled at compile time,
which is a bug. The same problem can also happen for (PPC_ISERIES &&
!PPC_PSERIES && PPC_SOMETHING_ELSE). In order to solve this, I
introduce a new CONFIG_PPC_NATIVE option that is set when at least
one platform is selected that can run without a hypervisor and then
turns the firmware feature check into a run-time option.
The new cell oprofile support that was recently merged does not
work on hypervisor based platforms like the PS3, therefore make
it depend on PPC_CELL_NATIVE instead of PPC_CELL. This may change
if we get oprofile support for PS3.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
|
|
Add PPU event-based and cycle-based profiling support to Oprofile for Cell.
Oprofile is expected to collect data on all CPUs simultaneously.
However, there is one set of performance counters per node. There are
two hardware threads or virtual CPUs on each node. Hence, OProfile must
multiplex in time the performance counter collection on the two virtual
CPUs.
The multiplexing of the performance counters is done by a virtual
counter routine. Initially, the counters are configured to collect data
on the even CPUs in the system, one CPU per node. In order to capture
the PC for the virtual CPU when the performance counter interrupt occurs
(the specified number of events between samples has occurred), the even
processors are configured to handle the performance counter interrupts
for their node. The virtual counter routine is called via a kernel
timer after the virtual sample time. The routine stops the counters,
saves the current counts, loads the last counts for the other virtual
CPU on the node, sets interrupts to be handled by the other virtual CPU
and restarts the counters, the virtual timer routine is scheduled to run
again. The virtual sample time is kept relatively small to make sure
sampling occurs on both CPUs on the node with a relatively small
granularity. Whenever the counters overflow, the performance counter
interrupt is called to collect the PC for the CPU where data is being
collected.
The oprofile driver relies on a firmware RTAS call to setup the debug bus
to route the desired signals to the performance counter hardware to be
counted. The RTAS call must set the routing registers appropriately in
each of the islands to pass the signals down the debug bus as well as
routing the signals from a particular island onto the bus. There is a
second firmware RTAS call to reset the debug bus to the non pass thru
state when the counters are not in use.
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Maynard Johnson <mpjohn@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Fixed a compile error in building the 85xx support with oprofile, and in
the process cleaned up some issues with the fsl_booke performance monitor
code.
* Reorganized FSL Book-E performance monitoring code so that the 7450
wouldn't be built if the e500 was, and cleaned it up so it was more
self-contained.
* Added a cpu_setup function for FSL Book-E. The original
cpu_setup function prototype had no arguments, assuming that
the reg_setup function would copy the required information into
variables which represented the registers. This was silly for
e500, since it has 1 register per counter (rather than 3 for
all counters), so the code has been restructured to have
cpu_setup take the current counter config array as an argument,
with op_powerpc_setup() invoking op_powerpc_cpu_setup() through
on_each_cpu(), and op_powerpc_cpu_setup() invoking the
model-specific cpu_setup function with an argument. The
argument is ignored on all other platforms at present.
* Fixed a confusing line where a trinary operator only had two
arguments
Signed-off-by: Andrew Fleming <afleming@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
nmi_create_files() in arch/i386/oprofile/nmi_int.c depends on
model->num_counters (number of performance counters) being less than 10.
While this is currently the case, it's too clever by half.
Other archs aren't quite as clever: they assume 100. I suggest to
normalize them all to 1000.
Cc: Philippe Elie <phil.el@wanadoo.fr>
Cc: John Levon <levon@movementarian.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch removes the changes from an earlier patch that disables
oProfile for iSeries within the oProfile KConfig (submitted Feb 23,
2006). Checks within the arch init for iSeries, still allowing profiling
for timer interrupts (using firmware_has_feature).
Signed-off-by: Kelly Daly <kelly@au.ibm.com>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
No need to always print out which performance monitoring type is used
on the console at every boot.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Remove oprofile spinlock backtrace code now we have proper calltrace
support. Also make MMCRA sihv and sipr bits a variable since they may
change in future cpus. Finally, MMCRA should be a 64bit quantity.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Add oprofile calltrace support to powerpc. Disable spinlock backtracing
now we can use calltrace info.
(Updated to work on both 32bit and 64bit by me).
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
In 2.6.15-git6 a change was commited in the oprofile support in
the powerpc architecture. It introduced the powerpc_oprofile_type
which contains the define G4. This causes a name clash with the
existing wacom usb tablet driver.
CC [M] drivers/usb/input/wacom.o
drivers/usb/input/wacom.c:98: error: conflicting types for `G4'
include/asm/cputable.h:37: error: previous declaration of `G4'
CC [M] drivers/usb/mon/mon_text.o
make[3]: *** [drivers/usb/input/wacom.o] Error 1
make[2]: *** [drivers/usb/input] Error 2
The elements of an enum declared in global scope are effectivly
global identifiers themselves. As such we need to ensure the names
are unique. This patch updates the later oprofile support to use
unique names.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
My recent changes to oprofile broke it when built as a module. Fix it by
using an enum instead of a function pointer. This way we still retain
the oprofile configuration in the cputable.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This patch adds oprofile support for the 7450 and all its multitudinous
derivatives.
* Added 7450 (and derivatives) support for oprofile
* Changed e500 cputable to have oprofile model and cpu_type fields
* Added support for classic 32-bit performance monitor interrupt
* Cleaned up common powerpc oprofile code to be as common as possible
* Cleaned up oprofile_impl.h to reflect 32 bit classic code
* Added 32-bit MMCRx bitfield definitions and SPR numbers
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This patches the ppc32 and ppc64 versions of the headers and .c files
with helper functions for manipulating the performance counting
hardware. As a side effect, it removes use of the term "perfmon" from
ppc32, thus avoiding confusion with the unrelated performance counter
interface from HP Labs also called "perfmon".
Built, but not booted, for g5, pSeries, iSeries, and 32-bit Powermac
with both ARCH=powerpc and ARCH=ppc{,64} as appropriate.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Changed ppc32 so that cur_cpu_spec is just a single pointer for all CPUs.
Additionally, made call_setup_cpu check to see if the cpu_setup pointer
is NULL or not before calling the function. This lets remove the dummy
cpu_setup calls that just return.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Rename and slightly modify {request,free}_perfmon_irq in the ppc code.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
- merge common.c
- move model specific files
- remove stub Makefiles
- clean up arch/ppc*/Makefile
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
