| Age | Commit message (Collapse) | Author |
|---|
|
master.kernel.org:/pub/scm/linux/kernel/git/galak/powerpc
* 'for_paulus' of master.kernel.org:/pub/scm/linux/kernel/git/galak/powerpc: (25 commits)
[POWERPC] 85xx: Added needed MPC85xx PCI device IDs
[POWERPC] Add Freescale PCI VENDOR ID and 8641 device IDs
[POWERPC] 85xxCDS: MPC8548 DTS cleanup.
[POWERPC] 85xxCDS: Misc 8548 PCI Corrections.
[POWERPC] 85xxCDS: Delay 8259 cascade hookup.
[POWERPC] 85xxCDS: Make sure restart resets the PCI bus.
[POWERPC] 85xxCDS: Allow 8259 cascade to share an MPIC interrupt line.
[POWERPC] FSL: Add support for PCI-X controllers
[POWERPC] Make sure virtual P2P bridge registers are setup on PCIe PHB
[POWERPC] Provide ability to setup P2P bridge registers from struct resource
[POWERPC] Add basic PCI/PCI Express support for 8544DS board
[POWERPC] Make endianess of cfg_addr for indirect pci ops runtime
[POWERPC] Removed setup_indirect_pci_nomap
[POWERPC] 85xx: Add quirk to ignore bogus FPGA on CDS
[POWERPC] 85xx: Added 8568 PCIe support
[POWERPC] Fixup resources on pci_bus for PCIe PHB when no device is connected
[POWERPC] Add basic PCI node for mpc8568mds board
[POWERPC] Use Freescale pci/pcie common code for 85xx boards
[POWERPC] Update PCI nodes in the 83xx/85xx boards device tree
[POWERPC] Add 8548 CDS PCI express controller node and PCI-X device node
...
|
|
spufs.h now has two enums for the sched_flags leading to identical
values for SPU_SCHED_WAS_ACTIVE and SPU_SCHED_NOTIFY_ACTIVE. Merge
them into a single enum as they were in the IBM development tree.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Setting the host bridge @8000 as primary. Also fixing a bug in
setting the USB interrupt numbers.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The interrupts of an E100 card inserted in PCI slot 4 may be on at bootup.
The resulting interrupt flood interacts with the 8259 cascade handler and
prevents proper boot up. There is a quirk for the E100 that will disable
the E100's interrupts but to use it, the 8259 cascade hookup must be
delayed until after the quirk has run. This patch delays the 8259 cascade
hookup by registering a device_initcall() which runs after the PCI quirk
for the E100.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The current 85xxCDS restart code fails to reset the PCI bus which can
lead to odd behavior after the restart. This patch uses the VIA Super
Southbridge to perform a PCI reset which will reset the entire system.
NOTE: Since the VIA chip is behind a PCI-to-PCI bridge which can be
disabled with a switch setting, it may not be possible to perform the
PCI bus reset. In this case, the code defaults to the previous restart
mechanism.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The Freescale MPC8555CDS and MPC8548CDS reference hardware has a legacy
8259 interrupt controller pair contained within a VIA VT82C686B Southbridge
on the main carrier board. The processor complex plugs into the carrier
card using a PCI slot which limits the available interrupts to the
INTA-INTD PCI interrupts. The output of the 8259 cascade pair is routed
through a gate array and connected to the PCI INTA interrupt line.
The normal interrupt chaining hook (set_irq_chained_handler) does
not allow sharing of the chained interrupt which prevents the
use of PCI INTA by PCI devices. This patch allows the 8259 cascade
pair to share their interrupt line with PCI devices.
NOTE: The addition of the .end routine for the MPIC is not strictly
necessary for this patch. It's there so this code will run from within
the threaded interrupt context used by the Real Time patch.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Add basic support for the PCIe PHB and enable the ULI bridge.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Make it so we do a runtime check to know if we need to write cfg_addr
as big or little endian. This is needed if we want to allow 86xx support
to co-exist in the same kernel as other 6xx PPCs.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The newer Arcadia boards for CDS have an FPGA that shows up on PCI
however isn't a real PCI device. Add a quirk to just ignore the
FPGA.
This is based on the following patch from Andy & York:
http://ozlabs.org/pipermail/linuxppc-dev/2007-February/032042.html
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Added the PCIe device node to the 8568 dts and the needed quirk entries.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
On the 85xx/86xx PCIe controllers if there is no device connected to the
PHB we will still allocate a pci_bus for downstream bus of the virtual
P2P bridge. However the resources allocated to the downstream bus are not
correct and so we just mimic the resources from the upstream pci_bus.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Switch the 85xx platform over to using the FSL generic PCI code. This
gets ups PCIe support in addition to base PCI support.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Rewrite the Freescale PCI code to support PCI on 83xx/85xx/86xx and
PCIe on 85xx/86xx.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Move
arch/powerpc/platforms/86xx/pci.c -> arch/powerpc/sysdev/fsl_pci.c
arch/powerpc/sysdev/fsl_pcie.h -> arch/powerpc/sysdev/fsl_pci.h
as the base to unify 83xx/85xx/86xx pci and pcie.
Add CONFIG_FSL_PCI to build fsl_pci.c for Freescale pci and pcie option.
The code still works for 86xx platforms.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Clean up duplicate includes in drivers/macintosh/
[POWERPC] Quiet section mismatch warning on pcibios_setup
[POWERPC] init and exit markings for hvc_iseries
[POWERPC] Quiet section mismatch in hvc_rtas.c
[POWERPC] Constify of_platform_driver match_table
[POWERPC] hvcs: Make some things static and const
[POWERPC] Constify of_platform_driver name
[POWERPC] MPIC protected sources
[POWERPC] of_detach_node()'s device node argument cannot be const
[POWERPC] Fix ARCH=ppc builds
[POWERPC] mv64x60: Use mutex instead of semaphore
[POWERPC] Allow smp_call_function_single() to current cpu
[POWERPC] Allow exec faults on readable areas on classic 32-bit PowerPC
[POWERPC] Fix future firmware feature fixups function failure
[POWERPC] fix showing xmon help
[POWERPC] Make xmon_write accept a const buffer
[POWERPC] Fix misspelled "CONFIG_CHECK_CACHE_COHERENCY" Kconfig option.
[POWERPC] cell: CONFIG_SPE_BASE is a typo
|
|
Fix a mismerge in commit 8b6f50ef1d5cc86b278eb42bc91630fad455fb10:
"spufs: make signal-notification files readonly for NOSCHED contexts",
where structs got duplicated.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Move firmware feature initialisation from pSeries_init_early to the
earlier pSeries_probe_hypertas so they are initialised before firmware
feature fixups are applied.
Currently firmware feature sections are only used for iSeries which
initialises the these features much earlier. This is a bug in waiting
on pSeries.
Also adds some whitespace fixups.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Reading from the signal{1,2} files requires a spu_acquire_saved, so make these
files write-only for contexts created with SPU_CREATE_NOSCHED.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add a FLASH ROM Storage Driver for the PS3:
- Implemented as a misc character device driver
- Uses a fixed 256 KiB buffer allocated from boot memory as the hypervisor
requires the writing of aligned 256 KiB blocks
Cc: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add a BD/DVD/CD-ROM Storage Driver for the PS3:
- Implemented as a SCSI device driver
- Uses software scatter-gather with a 64 KiB bounce buffer as the hypervisor
doesn't support scatter-gather
Cc: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add a Disk Storage Driver for the PS3:
- Implemented as a block device driver with a dynamic major
- Disk names (and partitions) are of the format ps3d%c(%u)
- Uses software scatter-gather with a 64 KiB bounce buffer as the hypervisor
doesn't support scatter-gather
Cc: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This sorts out the various lists and related locks in the spu code.
In detail:
- the per-node free_spus and active_list are gone. Instead struct spu
gained an alloc_state member telling whether the spu is free or not
- the per-node spus array is now locked by a per-node mutex, which
takes over from the global spu_lock and the per-node active_mutex
- the spu_alloc* and spu_free function are gone as the state change is
now done inline in the spufs code. This allows some more sharing of
code for the affinity vs normal case and more efficient locking
- some little refactoring in the affinity code for this locking scheme
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
|
|
From: Maynard Johnson <mpjohn@us.ibm.com>
This patch updates the existing arch/powerpc/oprofile/op_model_cell.c
to add in the SPU profiling capabilities. In addition, a 'cell' subdirectory
was added to arch/powerpc/oprofile to hold Cell-specific SPU profiling code.
Exports spu_set_profile_private_kref and spu_get_profile_private_kref which
are used by OProfile to store private profile information in spufs data
structures.
Also incorporated several fixes from other patches (rrn). Check pointer
returned from kzalloc. Eliminated unnecessary cast. Better error
handling and cleanup in the related area. 64-bit unsigned long parameter
was being demoted to 32-bit unsigned int and eventually promoted back to
unsigned long.
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Maynard Johnson <mpjohn@us.ibm.com>
Signed-off-by: Bob Nelson <rrnelson@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
|
|
SPU tasks
From: Maynard Johnson <mpjohn@us.ibm.com>
This patch adds to the capability of spu_switch_event_register so that
the caller is also notified of currently active SPU tasks.
Exports spu_switch_event_register and spu_switch_event_unregister so
that OProfile can get access to the notifications provided.
Signed-off-by: Maynard Johnson <mpjohn@us.ibm.com>
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Bob Nelson <rrnelson@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
|
|
Sort out the locking mess in spu_base and document the current rules.
As an added benefit spu_alloc* and spu_free don't block anymore.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
|
|
This patch links spus according to their physical position using
information provided by the firmware through a special vicinity
device-tree property. This property is present in current version
of Malta firmware.
Example of vicinity properties for a node in Malta:
Node: Vicinity property contains phandles of:
spe@0 [ spe@100000 , mic-tm@50a000 ]
spe@100000 [ spe@0 , spe@200000 ]
spe@200000 [ spe@100000 , spe@300000 ]
spe@300000 [ spe@200000 , bif0@512000 ]
spe@80000 [ spe@180000 , mic-tm@50a000 ]
spe@180000 [ spe@80000 , spe@280000 ]
spe@280000 [ spe@180000 , spe@380000 ]
spe@380000 [ spe@280000 , bif0@512000 ]
Only spe@* have a vicinity property (e.g., bif0@512000 and
mic-tm@50a000 do not have it).
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
|
|
This patch makes the scheduller honor affinity information for each
context being scheduled. If the context has no affinity information,
behaviour is unchanged. If there are affinity information, context is
schedulled to be run on the exact spu recommended by the affinity
placement algorithm.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
|
|
This patch provides the spu affinity placement logic for the spufs scheduler.
Each time a gang is going to be scheduled, the placement of a reference
context is defined. The placement of all other contexts with affinity from
the gang is defined based on this reference context location and on a
precomputed displacement offset.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
|
|
This patch adds support for additional flags at spu_create, which relate
to the establishment of affinity between contexts and contexts to memory.
A fourth, optional, parameter is supported. This parameter represent
a affinity neighbor of the context being created, and is used when defining
SPU-SPU affinity.
Affinity is represented as a doubly linked list of spu_contexts.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
|
|
This patch allows the use of spu affinity on QS20, whose
original FW does not provide affinity information.
This is done through two hardcoded arrays, and by reading the reg
property from each spu.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
|
|
This patch adds affinity data to each spu instance.
A doubly linked list is created, meant to connect the spus
in the physical order they are placed in the BE. SPUs
near to memory should be marked as having memory affinity.
Adjustments of the fields acording to FW properties is done
in separate patches, one for CPBW, one for Malta (patch for
Malta under testing).
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
|
|
Addition of a spufs-global "cbe_info" array. Each entry contains information
about one Cell/B.E. node, namelly:
* list of spus (both free and busy spus are in this list);
* list of free spus (replacing the static spu_list from spu_base.c)
* number of spus;
* number of reserved (non scheduleable) spus.
SPE affinity implementation actually requires only access to one spu per
BE node (since it implements its own pointer to walk through the other spus
of the ring) and the number of scheduleable spus (n_spus - non_sched_spus)
However having this more general structure can be useful for other
functionalities, concentrating per-cbe statistics / data.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
|
|
spu_sched->bitmap has MAX_PRIO(=140) width in bits.However, since
ff80a77f20f811c0cc5b251d0f657cbc6f788385, sched_find_first_bit()
only supports 100-bit bitmaps.
Thus, spu_sched->bitmap should be treated by generic find_first_bit().
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
|
|
From: Sebastian Siewior <cbe-oss-dev@ml.breakpoint.cc>
The 'file' argument is unused in spufs_run_spu(). This change removes
it.
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
|
|
The SPU decrementer should be restored after the LSCSA DMA has
completed.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
|
|
No need to halt the SPE decrementer at context restore step 47, it will
be done in step 7.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
|
|
At save step 8, the mfc control register in the CSA should be written
_only_ with Sc and Sm bits (at least MFC_CNTL[Dh] should be set to 0)
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
|
|
The decr_status in the LSCSA is valid only in the sequence of context
restore. Thus, it's nonsense to read and/or write it through spufs.
This patch changes decr_status node to access MFC_CNTL[Ds] in the CSA.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
|
|
The decr_status in the LSCSA is confusedly used as two meanings:
* SPU decrementer was running
* SPU decrementer was wrapped as a result of adjust
and the code to set decr_status is missing.
This patch fixes these problems by using the decr_status argument as a
set of flags. This requires a rebuild of the shipped spu_restore code.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
|
|
The following steps are not needed in the SPE context save/restore
paths:
Save Step 12: save_mfc_decr()
save suspend_time to CSA (It will be done by step 14)
save ch 7 (decrementer value will be saved in LSCSA by spe-side step 10)
Restore Step 59: restore_ch_part1()
restore ch 1 (it will be done by spe-side step 15)
This change removes the unnecessary steps.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
|
|
Based on a fix from Masato Noguchi <Masato.Noguchi@jp.sony.com>.
Remove the (incorrect) array size declarations in the spufs channel
arrays, and use ARRAY_SIZE rather than hardcoded values.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
|
|
Currently a process is removed from the physical spu when spu_acquire_saved
is saved but never put back. This patch adds a new spu_release_saved
that is to be paired with spu_acquire_saved and put the process back if
it has been in RUNNABLE state before.
Niether Jeremy not be are entirely happy about this exact patch because
it adds another spu_activate call outside of the owner thread, but I
feel this is the best short-term fix we can come up with.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
|
|
This patch exports per-context statistics in spufs as long as spu
statistics in sysfs.
It was formed by merging:
"spufs: add spu stats in sysfs" From: Christoph Hellwig
"spufs: add stat file to spufs" From: Christoph Hellwig
"spufs: fix libassist accounting" From: Jeremy Kerr
"spusched: fix spu utilization statistics" From: Luke Browning
And some adjustments by myself, after suggestions on cbe-oss-dev.
Having separate patches was making the review process harder
than it should, as we end up integrating spus and ctx statistics
accounting much more than it was on the first implementation.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
|
|
In 6cbf93960e64f313f6e247cbca7afaa50e3ee2c we added a WARN_ON for
calling spu_deactivate on contexts created with the SPU_CREATE_NOSCHED
flag. However, all NOSCHED contexts will need to be deactivated when
the context is destroyed, so this gives a spurious warning when any
NOSCHED context is closed.
This change removes the WARN_ON.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
|
|
Reading from the signal{1,2} files requires a spu_acquire_saved, so
make these files write-only for contexts created with
SPU_CREATE_NOSCHED.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
|
|
The current SPU context saving procedure in SPUFS unexpectedly
restarts MFC when halting decrementer, because MFC_CNTL[Dh] is set
without MFC_CNTL[Sm]. This bug causes, for example, saving broken DMA
queues. Here is a patch to fix the problem.
Signed-off-by: Kazunori Asayama <asayama@sm.sony.co.jp>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
|
|
WARNING: arch/powerpc/platforms/cell/spufs/spufs.o(.init.text+0x158): Section
mismatch: reference to .exit.text:.spu_sched_exit (between '.init_module' and
'.spu_sched_init')
was introduced by c99c1994a2bb9493b4ac372b2b6ee2606d291171
This patch removes the warning.
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
|
|
This patch adds support for the setup and decoding of MSIs
on Axon-based Cell systems, using the MSIC mechanism.
This involves setting up an area of BE memory which the Axon
then uses as a FIFO for MSI messages. When one or more MSIs
are decoded by the MSIC we receive an interrupt on the MPIC,
and the MSI messages are written into the FIFO. At the moment
we use a 64KB FIFO, one per MSIC/BE.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
|
|
This patch adds support for investigating spus information after a
kernel crash event, through kdump vmcore file.
Implementation is based on xmon code, but the new functionality was
kept independent from xmon.
Signed-off-by: Lucio Jose Herculano Correia <luciojhc@br.ibm.com>
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
|
