| Age | Commit message (Collapse) | Author |
|---|
|
On PS3, A storage device may show up in the repository before the hypervisor
has finished probing:
- If its type is not yet known, it shows up as PS3_DEV_TYPE_STOR_DUMMY,
- If its regions are being probed, it shows up as having zero regions.
If any of these happen, consider the device not yet present. The storage
probe thread will retry later.
This fixes the timing-dependent problem where a kernel booted from FLASH ROM
sometimes cannot find the hard disk.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
At present, running any SPE program on the ps3 will trigger a BUG_ON
when spufs_run_spu tries to clear the master run control bit, as lv1
does not make the master run control available to Linux.
This change makes SPE apps work again by disabling changes to the
master run control on PS3. Although we don't have the facility to
disable a SPE with supervisor-level privileges, it's better than
hitting the BUG_ON unconditionally.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Acked-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
interrupt.
The Cell BE Architecture spec states that the SPU MFC Class 0 interrupt
is edge-triggered. The current spu interrupt handler assumes this
behavior and does not clear the interrupt status.
The PS3 hypervisor visualizes all SPU interrupts as level, and on return
from the interrupt handler the hypervisor will deliver a new virtual
interrupt for any unmasked interrupts which for which the status has not
been cleared. This fix clears the interrupt status in the interrupt
handler.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Fix the bug that the major version part of the firmware version number
is ignored in the comparison done by ps3_compare_firmware_version
because the difference of two 64-bit quantities is returned as an int.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This fixes a major bug which was happening when a SPU thread advances
its execution right after being restored to a SPU. A potentially
outdated NPC value was being (re)written to the SPU.
So, spu_run_init, in this case, was either not doing anything relevant,
or breaking the execution of the SPU thread.
This fixes a common problem of losing a mailbox write when it was done
to a saved context.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
When a process writes into the inbound spu mailbox (wbox) while the
context is saved, we accidentally break the contents of the mb_stat_R
register by clearing other entries of the mailbox status register. This
can cause the user side to hang.
This change fixes the problem by only altering the appropriate bits
of the mailbox status register during a backing-store write.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This fixes a regression introduced with 2.6.23-rc4 after on some
confusion about the device tree interfaces.
IBM QS21 device trees provide "physical-id", so we changed the code to
run on that and remain compatible with all IBM machines.
However, the Toshiba Celleb device tree provides the "unit-id" property,
which was in the Linux code, but never used in this way on IBM hardware.
Legacy device tree used the reg property for the physical id of an spe.
This patch fixes find_spu_unit_number to look for the spu id in that order.
The length is checked to avoid misinterpretation in case the attributes
unit-id or reg do not contain the id.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Cc: Jeremy Kerr <jk@ozlabs.org>
|
|
The Cell Broadband Engine has a method of injecting a
system-reset-exception from an external source into the
operating system, which should trigger the regular behaviour
of entering xmon or kdump.
Unfortunately, the exception handler cannot distinguish it from
other interrupt causes by the SRR1 register, which gets used
for this on Power 6 and others.
IBM Blade servers that want to support triggering the
system reset exception using a pinhole button in the front
panel therefore use an extra register to determine the
reset cause.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
--
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Legacy device tree used the reg property for the physical id of an
spe. On newer device tree layouts the reg property contains the
"correct" value in the reg attribute. So there has been intoduced the
"physical-id" on newer devicetree layouts. The id is stored by
spu_manage into the spu struct as spe_id. cbe_thermal has been
changed to use the spu->spe_id. There's no need for the thermal code
to check devicetree attributes for itself.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Cc: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
More fallout from the switch from PAGE_SIZE based IOMMU to the native page
size for the driver. By pure luck it happened to work most of the time, since
we end up invalidating the wrong entries in the TLB.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/galak/powerpc
* 'fixes-2.6.23' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/powerpc:
[POWERPC] Fix 8xx compile failure
[POWERPC] Fix FSL BookE machine check reporting
[POWERPC] Fix interrupt routing and setup of ULI M1575 on FSL boards
[POWERPC] Add interrupt resource for RTC CMOS driver
|
|
The interrupt routing in the device trees for the ULI M1575 was
inproperly using the interrupt line field as pci function. Fixed
up the device tree's to actual conform for to specification and
changed the interrupt mapping code so it just uses a static mapping
setup as follows:
PIRQA - IRQ9
PIRQB - IRQ10
PIRQC - IRQ11
PIRQD - IRQ12
USB 1.1 OCHI (1c.0) - IRQ12
USB 1.1 OCHI (1c.1) - IRQ9
USB 1.1 OCHI (1c.2) - IRQ10
USB 1.1 ECHI (1c.3) - IRQ11
LAN (1b.0) - IRQ6
AC97 (1d.0) - IRQ6
Modem (1d.1) - IRQ6
HD Audio (1d.2) - IRQ6
SATA (1f.1) - IRQ5
SMB (1e.1) - IRQ7
PMU (1e.2) - IRQ7
PATA (1f.0) - IRQ14/15
Took the oppurtunity to refactor the code into a single file so we
don't have to duplicate these fixes on the two current boards in the
tree and several forth coming boards that will also need the code.
Fixed RTC support that requires a dummy memory read on the P2P bridge
to unlock the RTC and setup the default of the RTC alarm registers to
match with a basic x86 style CMOS RTC.
Moved code that poked ISA registers to a FIXUP_FINAL quirk to ensure
the PCI IO space has been setup properly before we start poking ISA
registers at random locations.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Fix probing of PS3 storage devices: in the success case, we should set
`error' to zero, not `result'.
Without this patch no storage devices are found.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
At present, spu_create with an invalid neighbo(u)r will return -ENOSYS,
not -EBADF, but only when spufs.o is built as a module.
This change adds the appropriate errno, making the behaviour the same
as the built-in case.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
with QE UEC"
This reverts commit 3baee955953957be5496cd28e9c544d9db214262.
That commit was a mistake from the start; I added mdio type to the
bus scan list early on in my ucc_geth migrate to phylib development,
which is just pure wrong (the ucc_geth_mii driver creates the mii
bus and the PHY layer handles PHY enumeration without translation).
This follows on from commit 77926826f301fbd8ed96d3cd9ff17a5b59560dfb:
Revert "[POWERPC] Don't complain if size-cells == 0 in prom_parse()"
which was basically trying to hide a symptom of the original mistake
this revert fixes.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Remove the Kconfig message that indicates the PS3 platform support is
incomplete.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Fix the PS3 storage probe logic to properly find device regions on cold
startup.
o Change the storage probe event mask from notify_device_ready
to notify_region_update.
o Improve the storage probe error handling.
o Change ps3_storage_wait_for_device() to use a temporary variable to hold
the buffer address.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This patch moves affinity initialization code from spu_base.c to a
new spu_management_of_ops function (init_affinity), which is empty
in the case of PS3. This fixes a linking problem that was happening
when compiling for PS3.
Also, some small code style changes were made.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
...by using the pci_get API instead of the deprecated old stuff.
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
WARNING: vmlinux.o(.text+0x605d4): Section mismatch: reference to
.init.text:.__alloc_bootmem (between '.prealloc' and '.ps3_power_save')
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This patch fixes affinity reference point placement, which was not being
done in some situations, after the introduction of node_allowed() calls.
The previously used parameter, 'ctx', is just the iterator of the
previous list_for_each_entry_reverse loop, and its value might be
invalid at the end of the loop. Also, the right context to seek
for information when defining the reference ctx location
_is_ the reference ctx.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Currently we calculate the first timeslice for every context
incorrectly - alloc_spu_context calls spu_set_timeslice before we set
ctx->prio so we always calculate the longest possible timeslice for the
lowest possible priority.
This patch makes sure to update the schedule-related fields before
calculating the timeslice and also makes sure we update the timeslice for
a non-running context when entering spu_run so a priority change affects
the context as soon as possible.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
We currently initialize cbe_spu_info[].spus in both init_spu_base and
spu_sched_init. The initialise in spu_sched_init clears the SPU list,
so we end up with no physical SPUs. Because of this, the spu_run
syscall will block forever.
This change removes the unnecessary initialization in spu_sched_init.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The Maple platform has ISA IOs but didn't call the new functions to
actually map those, thus crashing when trying to access the nvram.
This fixes Maple and JS2x using SLOF.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
WARNING: vmlinux.o(.text+0x4f568): Section mismatch: reference to .init.text:.__alloc_bootmem (between '.setup_hvlpevent_queue' and '.process_hvlpevents')
setup_hvlpevent_queue is only called from __init code so make it __init
as well.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/galak/powerpc
* 'for_paulus' of master.kernel.org:/pub/scm/linux/kernel/git/galak/powerpc: (25 commits)
[POWERPC] 85xx: Added needed MPC85xx PCI device IDs
[POWERPC] Add Freescale PCI VENDOR ID and 8641 device IDs
[POWERPC] 85xxCDS: MPC8548 DTS cleanup.
[POWERPC] 85xxCDS: Misc 8548 PCI Corrections.
[POWERPC] 85xxCDS: Delay 8259 cascade hookup.
[POWERPC] 85xxCDS: Make sure restart resets the PCI bus.
[POWERPC] 85xxCDS: Allow 8259 cascade to share an MPIC interrupt line.
[POWERPC] FSL: Add support for PCI-X controllers
[POWERPC] Make sure virtual P2P bridge registers are setup on PCIe PHB
[POWERPC] Provide ability to setup P2P bridge registers from struct resource
[POWERPC] Add basic PCI/PCI Express support for 8544DS board
[POWERPC] Make endianess of cfg_addr for indirect pci ops runtime
[POWERPC] Removed setup_indirect_pci_nomap
[POWERPC] 85xx: Add quirk to ignore bogus FPGA on CDS
[POWERPC] 85xx: Added 8568 PCIe support
[POWERPC] Fixup resources on pci_bus for PCIe PHB when no device is connected
[POWERPC] Add basic PCI node for mpc8568mds board
[POWERPC] Use Freescale pci/pcie common code for 85xx boards
[POWERPC] Update PCI nodes in the 83xx/85xx boards device tree
[POWERPC] Add 8548 CDS PCI express controller node and PCI-X device node
...
|
|
spufs.h now has two enums for the sched_flags leading to identical
values for SPU_SCHED_WAS_ACTIVE and SPU_SCHED_NOTIFY_ACTIVE. Merge
them into a single enum as they were in the IBM development tree.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Setting the host bridge @8000 as primary. Also fixing a bug in
setting the USB interrupt numbers.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The interrupts of an E100 card inserted in PCI slot 4 may be on at bootup.
The resulting interrupt flood interacts with the 8259 cascade handler and
prevents proper boot up. There is a quirk for the E100 that will disable
the E100's interrupts but to use it, the 8259 cascade hookup must be
delayed until after the quirk has run. This patch delays the 8259 cascade
hookup by registering a device_initcall() which runs after the PCI quirk
for the E100.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The current 85xxCDS restart code fails to reset the PCI bus which can
lead to odd behavior after the restart. This patch uses the VIA Super
Southbridge to perform a PCI reset which will reset the entire system.
NOTE: Since the VIA chip is behind a PCI-to-PCI bridge which can be
disabled with a switch setting, it may not be possible to perform the
PCI bus reset. In this case, the code defaults to the previous restart
mechanism.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The Freescale MPC8555CDS and MPC8548CDS reference hardware has a legacy
8259 interrupt controller pair contained within a VIA VT82C686B Southbridge
on the main carrier board. The processor complex plugs into the carrier
card using a PCI slot which limits the available interrupts to the
INTA-INTD PCI interrupts. The output of the 8259 cascade pair is routed
through a gate array and connected to the PCI INTA interrupt line.
The normal interrupt chaining hook (set_irq_chained_handler) does
not allow sharing of the chained interrupt which prevents the
use of PCI INTA by PCI devices. This patch allows the 8259 cascade
pair to share their interrupt line with PCI devices.
NOTE: The addition of the .end routine for the MPIC is not strictly
necessary for this patch. It's there so this code will run from within
the threaded interrupt context used by the Real Time patch.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Add basic support for the PCIe PHB and enable the ULI bridge.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Make it so we do a runtime check to know if we need to write cfg_addr
as big or little endian. This is needed if we want to allow 86xx support
to co-exist in the same kernel as other 6xx PPCs.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The newer Arcadia boards for CDS have an FPGA that shows up on PCI
however isn't a real PCI device. Add a quirk to just ignore the
FPGA.
This is based on the following patch from Andy & York:
http://ozlabs.org/pipermail/linuxppc-dev/2007-February/032042.html
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Added the PCIe device node to the 8568 dts and the needed quirk entries.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
On the 85xx/86xx PCIe controllers if there is no device connected to the
PHB we will still allocate a pci_bus for downstream bus of the virtual
P2P bridge. However the resources allocated to the downstream bus are not
correct and so we just mimic the resources from the upstream pci_bus.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Switch the 85xx platform over to using the FSL generic PCI code. This
gets ups PCIe support in addition to base PCI support.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Rewrite the Freescale PCI code to support PCI on 83xx/85xx/86xx and
PCIe on 85xx/86xx.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Move
arch/powerpc/platforms/86xx/pci.c -> arch/powerpc/sysdev/fsl_pci.c
arch/powerpc/sysdev/fsl_pcie.h -> arch/powerpc/sysdev/fsl_pci.h
as the base to unify 83xx/85xx/86xx pci and pcie.
Add CONFIG_FSL_PCI to build fsl_pci.c for Freescale pci and pcie option.
The code still works for 86xx platforms.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Clean up duplicate includes in drivers/macintosh/
[POWERPC] Quiet section mismatch warning on pcibios_setup
[POWERPC] init and exit markings for hvc_iseries
[POWERPC] Quiet section mismatch in hvc_rtas.c
[POWERPC] Constify of_platform_driver match_table
[POWERPC] hvcs: Make some things static and const
[POWERPC] Constify of_platform_driver name
[POWERPC] MPIC protected sources
[POWERPC] of_detach_node()'s device node argument cannot be const
[POWERPC] Fix ARCH=ppc builds
[POWERPC] mv64x60: Use mutex instead of semaphore
[POWERPC] Allow smp_call_function_single() to current cpu
[POWERPC] Allow exec faults on readable areas on classic 32-bit PowerPC
[POWERPC] Fix future firmware feature fixups function failure
[POWERPC] fix showing xmon help
[POWERPC] Make xmon_write accept a const buffer
[POWERPC] Fix misspelled "CONFIG_CHECK_CACHE_COHERENCY" Kconfig option.
[POWERPC] cell: CONFIG_SPE_BASE is a typo
|
|
Fix a mismerge in commit 8b6f50ef1d5cc86b278eb42bc91630fad455fb10:
"spufs: make signal-notification files readonly for NOSCHED contexts",
where structs got duplicated.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Move firmware feature initialisation from pSeries_init_early to the
earlier pSeries_probe_hypertas so they are initialised before firmware
feature fixups are applied.
Currently firmware feature sections are only used for iSeries which
initialises the these features much earlier. This is a bug in waiting
on pSeries.
Also adds some whitespace fixups.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Reading from the signal{1,2} files requires a spu_acquire_saved, so make these
files write-only for contexts created with SPU_CREATE_NOSCHED.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add a FLASH ROM Storage Driver for the PS3:
- Implemented as a misc character device driver
- Uses a fixed 256 KiB buffer allocated from boot memory as the hypervisor
requires the writing of aligned 256 KiB blocks
Cc: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add a BD/DVD/CD-ROM Storage Driver for the PS3:
- Implemented as a SCSI device driver
- Uses software scatter-gather with a 64 KiB bounce buffer as the hypervisor
doesn't support scatter-gather
Cc: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add a Disk Storage Driver for the PS3:
- Implemented as a block device driver with a dynamic major
- Disk names (and partitions) are of the format ps3d%c(%u)
- Uses software scatter-gather with a 64 KiB bounce buffer as the hypervisor
doesn't support scatter-gather
Cc: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This sorts out the various lists and related locks in the spu code.
In detail:
- the per-node free_spus and active_list are gone. Instead struct spu
gained an alloc_state member telling whether the spu is free or not
- the per-node spus array is now locked by a per-node mutex, which
takes over from the global spu_lock and the per-node active_mutex
- the spu_alloc* and spu_free function are gone as the state change is
now done inline in the spufs code. This allows some more sharing of
code for the affinity vs normal case and more efficient locking
- some little refactoring in the affinity code for this locking scheme
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
|
|
From: Maynard Johnson <mpjohn@us.ibm.com>
This patch updates the existing arch/powerpc/oprofile/op_model_cell.c
to add in the SPU profiling capabilities. In addition, a 'cell' subdirectory
was added to arch/powerpc/oprofile to hold Cell-specific SPU profiling code.
Exports spu_set_profile_private_kref and spu_get_profile_private_kref which
are used by OProfile to store private profile information in spufs data
structures.
Also incorporated several fixes from other patches (rrn). Check pointer
returned from kzalloc. Eliminated unnecessary cast. Better error
handling and cleanup in the related area. 64-bit unsigned long parameter
was being demoted to 32-bit unsigned int and eventually promoted back to
unsigned long.
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Maynard Johnson <mpjohn@us.ibm.com>
Signed-off-by: Bob Nelson <rrnelson@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
|
|
SPU tasks
From: Maynard Johnson <mpjohn@us.ibm.com>
This patch adds to the capability of spu_switch_event_register so that
the caller is also notified of currently active SPU tasks.
Exports spu_switch_event_register and spu_switch_event_unregister so
that OProfile can get access to the notifications provided.
Signed-off-by: Maynard Johnson <mpjohn@us.ibm.com>
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Bob Nelson <rrnelson@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
|
