aboutsummaryrefslogtreecommitdiff
path: root/arch/powerpc
AgeCommit message (Collapse)Author
2006-10-16[POWERPC] powerpc: Enable DEEPNAP power savings mode on 970MPOlof Johansson
Without this patch, on an idle system I get: cpu-power-0:21.638 cpu-power-1:27.102 cpu-power-2:29.343 cpu-power-3:25.784 Total: 103.8W With this patch: cpu-power-0:11.730 cpu-power-1:17.185 cpu-power-2:18.547 cpu-power-3:17.528 Total: 65.0W If I lower HZ to 100, I can get it as low as: cpu-power-0:10.938 cpu-power-1:16.021 cpu-power-2:17.245 cpu-power-3:16.145 Total: 60.2W Another (older) Quad G5 went from 54W to 39W at HZ=250. Coming back out of Deep Nap takes 40-70 cycles longer than coming back from just Nap (which already takes quite a while). I don't think it'll be a performance issue (interrupt latency on an idle system), but in case someone does measurements feel free to report them. Signed-off-by: Olof Johansson <olof@lixom.net> Acked-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-16[POWERPC] Lazy interrupt disabling for 64-bit machinesPaul Mackerras
This implements a lazy strategy for disabling interrupts. This means that local_irq_disable() et al. just clear the 'interrupts are enabled' flag in the paca. If an interrupt comes along, the interrupt entry code notices that interrupts are supposed to be disabled, and clears the EE bit in SRR1, clears the 'interrupts are hard-enabled' flag in the paca, and returns. This means that interrupts only actually get disabled in the processor when an interrupt comes along. When interrupts are enabled by local_irq_enable() et al., the code sets the interrupts-enabled flag in the paca, and then checks whether interrupts got hard-disabled. If so, it also sets the EE bit in the MSR to hard-enable the interrupts. This has the potential to improve performance, and also makes it easier to make a kernel that can boot on iSeries and on other 64-bit machines, since this lazy-disable strategy is very similar to the soft-disable strategy that iSeries already uses. This version renames paca->proc_enabled to paca->soft_enabled, and changes a couple of soft-disables in the kexec code to hard-disables, which should fix the crash that Michael Ellerman saw. This doesn't yet use a reserved CR field for the soft_enabled and hard_enabled flags. This applies on top of Stephen Rothwell's patches to make it possible to build a combined iSeries/other kernel. Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-16[POWERPC] Check for offline nodes in pci NUMA codeAnton Blanchard
During boot we bring up all memory and cpu nodes. Normally a PCI device will be in one of these online nodes, however in some weird setups it may not. We have only seen this in the lab but we may as well check for the case and fallback to -1 (all nodes). Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-16[POWERPC] Better check in show_instructionsAnton Blanchard
Instead of just checking that an address is in the right range, use the provided __kernel_text_address() helper which covers both the kernel and module text sections. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-16[POWERPC] POWER6 has 6 PMCsAnton Blanchard
Change ->num_pmcs to match the number of PMCs in POWER6. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-16[POWERPC] Never panic when taking altivec exceptions from userspaceAnton Blanchard
At the moment we rely on a cpu feature bit or a firmware property to detect altivec. If we dont have either of these and the cpu does in fact support altivec we can cause a panic from userspace. It seems safer to always send a signal if we manage to get an 0xf20 exception from userspace. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-16[POWERPC] Fix IO Window Updates on P2P bridges.Randy Vinson
When update_bridge_base() updates the IO window on a PCI-to-PCI bridge, it fails to zero the upper 16 bits of the base and limit registers if the window size is less than 64K. This fixes it. Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-16[POWERPC] Add Makefile entry for MPC832x_mds supportLi Yang
Add missing entry in Makefile for MPC832x MDS support. It also change white space to tab in MPC8360 entry. Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-16[POWERPC] Fix MPC8360EMDS PB board supportLi Yang
MPC8360EMDS PB support is broken as some code was missing in last submission. This patch adds missing code and makes MPC8360EMDS PB support working. Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-16[POWERPC] Add DOS partition table support to mpc834x_itx_defconfigTimur Tabi
The default configuration file for the MPC8349E-mITX reference board, mpc834x_itx_defconfig, did not include support for DOS partition table types. This support is necessary because the hard drive that comes with the ITX is formatted with this partition table type. Without this config option, no partitions on the drive can be mounted. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-16[POWERPC] spufs: fix support for read/write on cntlNoguchi, Masato
This fixes a memory leak introduced by "spufs: add support for read/write oncntl", which was missing a call to simple_attr_close. Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com> Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-16[POWERPC] Don't crash on cell with 2 BEs when !CONFIG_NUMABenjamin Herrenschmidt
The SPU code will crash if CONFIG_NUMA is not set and SPUs are found on a non-0 node. This workaround will ignore those SPEs and just print an message in the kernel log. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-11[PATCH] mm: use symbolic names instead of indices for zone initialisationMel Gorman
Arch-independent zone-sizing is using indices instead of symbolic names to offset within an array related to zones (max_zone_pfns). The unintended impact is that ZONE_DMA and ZONE_NORMAL is initialised on powerpc instead of ZONE_DMA and ZONE_HIGHMEM when CONFIG_HIGHMEM is set. As a result, the the machine fails to boot but will boot with CONFIG_HIGHMEM turned off. The following patch properly initialises the max_zone_pfns[] array and uses symbolic names instead of indices in each architecture using arch-independent zone-sizing. Two users have successfully booted their powerpcs with it (one an ibook G4). It has also been boot tested on x86, x86_64, ppc64 and ia64. Please merge for 2.6.19-rc2. Credit to Benjamin Herrenschmidt for identifying the bug and rolling the first fix. Additional credit to Johannes Berg and Andreas Schwab for reporting the problem and testing on powerpc. Signed-off-by: Mel Gorman <mel@csn.ul.ie> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-10Merge branch 'merge' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc * 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: [POWERPC] Fix windfarm platform device usage [POWERPC] Fix i2c-powermac platform device usage [POWERPC] Fix secondary CPU startup on old "powersurge" SMP powermacs [POWERPC] ARCH=ppc pt_regs fixes [POWERPC] Update maple defconfig [POWERPC] Fix Maple secondary IDE interrupt [POWERPC] Make U4 PCIe work on maple [POWERPC] cell: fix default zImage build target [POWERPC] Fix boot wrapper invocation if CROSS_COMPILE contains spaces [POWERPC] Fix xmon IRQ handler for pt_regs removal
2006-10-10[POWERPC] Fix secondary CPU startup on old "powersurge" SMP powermacsPaul Mackerras
On the old "powersurge" SMP powermacs, the second CPU is started up by sending it an IPI, which has the side effect of stopping the timebase clock (so the secondary CPU's timebase can be synchronized with the primary's). The routine that did this used udelay, which will hang forever when the timebase is stopped, since udelay now spins until the timebase reaches a certain value. The end result is that the kernel would hang when bringing up the second CPU. This fixes it by using a simple loop which just does a fixed number of iterations to generate the delay. These old systems were all clocked at around 200 MHz or so, so a fixed number of iterations is acceptable. Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-10[POWERPC] Update maple defconfigBenjamin Herrenschmidt
This updates the Maple defconfig to 4 CPUs (along with current defaults) to support the "tigerwood" 970MP evaluation board. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-10[POWERPC] Fix Maple secondary IDE interruptBenjamin Herrenschmidt
The IDE driver will pick up the PCI IRQ for both channels on Maple despite the fact that it's in legacy mode. This works around it by "hiding" the PCI IRQ of the AMD8111 IDE controller when it's configured in legacy mode on the Maple platform, thus causing the driver to call pci_get_legacy_ide_irq() which will return the correct interrupts for both channels. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-10[POWERPC] Make U4 PCIe work on mapleBenjamin Herrenschmidt
The Maple support code was missing code for U4/CPC945 PCIe. This adds it, enabling it to work on tigerwood boards, and possibly also js21 using SLOF. Also disable an obsolete firmware workaround. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-10[POWERPC] cell: fix default zImage build targetGeoff Levand
Change CONFIG_PPC_CELL to CONFIG_PPC_IBM_CELL_BLADE in the powerpc boot makefile. CONFIG_PPC_CELL is used to build the generic cell processor support, and is not an indication of platform. Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-10[POWERPC] Fix boot wrapper invocation if CROSS_COMPILE contains spacesMichael Ellerman
My CROSS_COMPILE is "ccache /opt/compilers/blah", which confuses the boot wrapper script. Quote CROSS_COMPILE and CROSS32_COMPILE so they can safely contain spaces. Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-10[POWERPC] Fix xmon IRQ handler for pt_regs removalPaul Mackerras
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-09[HEADERS] Put linux/config.h out of its misery.Dave Jones
Signed-off-by: Dave Jones <davej@redhat.com>
2006-10-09Merge git://git.infradead.org/~dhowells/irq-2.6Linus Torvalds
* git://git.infradead.org/~dhowells/irq-2.6: IRQ: Use the new typedef for interrupt handler function pointers
2006-10-09[PATCH] trivial iomem annotations (arch/powerpc/platfroms/parsemi/pci.c)Al Viro
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Acked-by: Olof Johansson <olof@lixom.net> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-09[PATCH] extern doesn't make sense on a definition of function...Al Viro
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-09IRQ: Use the new typedef for interrupt handler function pointersDavid Howells
Use the new typedef for interrupt handler function pointers rather than actually spelling out the full thing each time. This was scripted with the following small shell script: #!/bin/sh egrep -nHrl -e 'irqreturn_t[ ]*[(][*]' $* | while read i do echo $i perl -pi -e 's/irqreturn_t\s*[(]\s*[*]\s*([_a-zA-Z0-9]*)\s*[)]\s*[(]\s*int\s*,\s*void\s*[*]\s*[)]/irq_handler_t \1/g' $i || exit $? done Signed-Off-By: David Howells <dhowells@redhat.com>
2006-10-08Revert "[POWERPC] Don't get PCI IRQ from OF for devices with no IRQ"Linus Torvalds
This reverts commit 41550c5128150175197257b6ceab2cd50dea7b51. Quoth Ben Herrenschmidt: "Please revert this one for now. It seems to break G5s :( Looks like PCI cells inside Apple IO ASICs don't have a PCI_INTERRUPT_LINE set. I need to figure out a better fix." Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-07[POWERPC] SPU fixup after irq changesOlaf Hering
Remove struct pt_regs * from remaining spu irq functions. Signed-off-by: Olaf Hering <olaf@aepfle.de> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-07[POWERPC] Fix up after irq changesOlaf Hering
Remove struct pt_regs * from all handlers. Also remove the regs argument from get_irq() functions. Compile tested with arch/powerpc/config/* and arch/ppc/configs/prep_defconfig Signed-off-by: Olaf Hering <olaf@aepfle.de> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-07[POWERPC] Fix iseries/smp.c for irq breakageStephen Rothwell
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-07[POWERPC] Update iseries_defconfigStephen Rothwell
This make sure that an iseries_defconfig does not inlude other platforms. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-07[POWERPC] Fix fsl_soc build breaksOlof Johansson
Hrm, there's no way this ever built at time of merge. There's a missing } and the wrong type on phy_irq. Also, another const for get_property(). CC arch/powerpc/sysdev/fsl_soc.o arch/powerpc/sysdev/fsl_soc.c: In function 'fs_enet_of_init': arch/powerpc/sysdev/fsl_soc.c:625: error: assignment of read-only variable 'phy_irq' arch/powerpc/sysdev/fsl_soc.c:625: warning: assignment makes integer from pointer without a cast arch/powerpc/sysdev/fsl_soc.c:661: warning: assignment discards qualifiers from pointer target type arch/powerpc/sysdev/fsl_soc.c:684: error: subscripted value is neither array nor pointer arch/powerpc/sysdev/fsl_soc.c:687: error: subscripted value is neither array nor pointer arch/powerpc/sysdev/fsl_soc.c:722: warning: ISO C90 forbids mixed declarations and code arch/powerpc/sysdev/fsl_soc.c:728: error: invalid storage class for function 'cpm_uart_of_init' arch/powerpc/sysdev/fsl_soc.c:798: error: initializer element is not constant arch/powerpc/sysdev/fsl_soc.c:798: error: expected declaration or statement at end of input make[1]: *** [arch/powerpc/sysdev/fsl_soc.o] Error 1 Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-06[POWERPC] Minor fix for bootargs propertyGeoff Levand
Avoid the use of an uninitialized stack variable when the powerpc device tree bootargs property is either missing or incorrectly defined. This also makes CONFIG_CMDLINE work properly under these conditions. This change adds a test for the existence of the bootargs property. early_init_dt_scan_chosen() tests for a zero length bootargs property in its CONFIG_CMDLINE processing, but the current implementation of of_get_flat_dt_prop() doesn't assign a value to the length when no property is found. Since an automatic variable is used, a stale value from the stack will be used in the test. Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-06[POWERPC] Update pSeries defconfig for SATABrian King
Since the ipr driver now supports SATA and depends on libata, enable libata to get built. Signed-off-by: Brian King <brking@us.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-06[POWERPC] Don't get PCI IRQ from OF for devices with no IRQBenjamin Herrenschmidt
This patch adds checking of the PCI_INTERRUPT_PIN register before using standard OF parsing to retreive PCI interrupts. The reason is that some PCI devices may have no PCI interrupt, though they may have interrupts attached via other means. In this case, we shall not use irq->pdev, but device-specific code can later retreive those interrupts instead. Without that patch, Maple and derivatives don't get the right interrupt for the second IDE channel as the linux IDE code fallsback to the PCI irq instead of trying to use the legacy ones for the on-board controller (which has no PCI_INTERRUPT_PIN). Having no PCI IRQ assign to it (as it doesn't request any) fixes it. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-06[POWERPC] Fix zImage decompress locationBenjamin Herrenschmidt
The zImage wrapper has a "hack" that force the decompression to happen above 20Mb for 64 bits kernels, to work around issues with some firmwares on the field. However, the new wrapper has a bug which makes that hack not work properly. This fixes it. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-06[POWERPC] linux,tce-size property is 32 bitsNathan Lynch
The "linux,tce-size" property is only 32 bits (see prom_initialize_tce_table() in arch/powerpc/kernel/prom_init.c). Treating it as an unsigned long in iommu_table_setparms() leads to access beyond the end of the property's buffer, so we pass garbage to the memset() in that function. [boot]0020 XICS Init i8259 legacy interrupt controller initialized [boot]0021 XICS Done PID hash table entries: 4096 (order: 12, 32768 bytes) cpu 0x0: Vector: 300 (Data Access) at [c0000000fe783850] pc: c000000000035e90: .memset+0x60/0xfc lr: c000000000044fa4: .iommu_table_setparms+0xb0/0x158 sp: c0000000fe783ad0 msr: 9000000000009032 dar: c000000100000000 dsisr: 42010000 current = 0xc00000000450e810 paca = 0xc000000000411580 pid = 1, comm = swapper enter ? for help [link register ] c000000000044fa4 .iommu_table_setparms+0xb0/0x158 [c0000000fe783ad0] c000000000044f4c .iommu_table_setparms+0x58/0x158 (unreliable) [c0000000fe783b70] c00000000004529c .iommu_bus_setup_pSeries+0x1c4/0x254 [c0000000fe783c00] c00000000002b8ac .do_bus_setup+0x3c/0xe4 [c0000000fe783c80] c00000000002c924 .pcibios_fixup_bus+0x64/0xd8 [c0000000fe783d00] c0000000001a2d5c .pci_scan_child_bus+0x6c/0x10c [c0000000fe783da0] c00000000002be28 .scan_phb+0x17c/0x1b4 [c0000000fe783e40] c0000000003cfa00 .pcibios_init+0x58/0x19c [c0000000fe783ec0] c0000000000094b4 .init+0x1e8/0x3d8 [c0000000fe783f90] c000000000026e54 .kernel_thread+0x4c/0x68 Signed-off-by: Nathan Lynch <ntl@pobox.com> Acked-by: Olof Johansson <olof@lixom.net> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-06[POWERPC] Add DTS for MPC8349E-mITX boardTimur Tabi
Add the DTS for the Freescale MPC 8349E-mITX reference board. Contact Vitesse for the driver for the VSC 7385. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-06[POWERPC] Fix harmless typoNick Piggin
Fix a typo. Noticed by the unlikely profiler. Signed-off-by: Nick Piggin <npiggin@suse.de> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-05[PATCH] powerpc: irq change build breaksOlof Johansson
Fix up some of the buildbreaks from the irq handler changes. Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-05IRQ: Maintain regs pointer globally rather than passing to IRQ handlersDavid Howells
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead of passing regs around manually through all ~1800 interrupt handlers in the Linux kernel. The regs pointer is used in few places, but it potentially costs both stack space and code to pass it around. On the FRV arch, removing the regs parameter from all the genirq function results in a 20% speed up of the IRQ exit path (ie: from leaving timer_interrupt() to leaving do_IRQ()). Where appropriate, an arch may override the generic storage facility and do something different with the variable. On FRV, for instance, the address is maintained in GR28 at all times inside the kernel as part of general exception handling. Having looked over the code, it appears that the parameter may be handed down through up to twenty or so layers of functions. Consider a USB character device attached to a USB hub, attached to a USB controller that posts its interrupts through a cascaded auxiliary interrupt controller. A character device driver may want to pass regs to the sysrq handler through the input layer which adds another few layers of parameter passing. I've build this code with allyesconfig for x86_64 and i386. I've runtested the main part of the code on FRV and i386, though I can't test most of the drivers. I've also done partial conversion for powerpc and MIPS - these at least compile with minimal configurations. This will affect all archs. Mostly the changes should be relatively easy. Take do_IRQ(), store the regs pointer at the beginning, saving the old one: struct pt_regs *old_regs = set_irq_regs(regs); And put the old one back at the end: set_irq_regs(old_regs); Don't pass regs through to generic_handle_irq() or __do_IRQ(). In timer_interrupt(), this sort of change will be necessary: - update_process_times(user_mode(regs)); - profile_tick(CPU_PROFILING, regs); + update_process_times(user_mode(get_irq_regs())); + profile_tick(CPU_PROFILING); I'd like to move update_process_times()'s use of get_irq_regs() into itself, except that i386, alone of the archs, uses something other than user_mode(). Some notes on the interrupt handling in the drivers: (*) input_dev() is now gone entirely. The regs pointer is no longer stored in the input_dev struct. (*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does something different depending on whether it's been supplied with a regs pointer or not. (*) Various IRQ handler function pointers have been moved to type irq_handler_t. Signed-Off-By: David Howells <dhowells@redhat.com> (cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
2006-10-05[POWERPC] cell: fix bugs found by sparseArnd Bergmann
- Some long constants should be marked 'ul'. - When using desc->handler_data to pass an __iomem register area, we need to add casts to and from __iomem. Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-05[POWERPC] spiderpic: enable new style devtree supportArnd Bergmann
This enables support for new firmware test releases. Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-05[POWERPC] Update cell_defconfigArnd Bergmann
This adds defaults for new configuration options added since 2.6.18 and it enables the option for 64kb pages by default. Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-05[POWERPC] spufs: add infrastructure for finding elf objectsArnd Bergmann
This adds an 'object-id' file that the spe library can use to store a pointer to its ELF object. This was originally meant for use by oprofile, but is now also used by the GNU debugger, if available. In order for oprofile to find the location in an spu-elf binary where an event counter triggered, we need a way to identify the binary in the first place. Unfortunately, that binary itself can be embedded in a powerpc ELF binary. Since we can assume it is mapped into the effective address space of the running process, have that one write the pointer value into a new spufs file. When a context switch occurs, pass the user value to the profiler so that can look at the mapped file (with some care). Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-05[POWERPC] spufs: support new OF device tree formatArnd Bergmann
The properties we used traditionally in the device tree are somewhat nonstandard. This adds support for a more conventional format using 'interrupts' and 'reg' properties. The interrupts are specified in three cells (class 0, 1 and 2) and registered at the interrupt-parent. The reg property contains either three or four register areas in the order 'local-store', 'problem', 'priv2', and 'priv1', so the priv1 one can be left out in case of hypervisor driven systems that access these through hcalls. Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-05[POWERPC] spufs: add support for read/write on cntlArnd Bergmann
Writing to cntl can be used to stop execution on the spu and to restart it, reading from cntl gives the contents of the current status register. The access is always in ascii, as for most other files. This was always meant to be there, but we had a little problem with writing to runctl so it was left out so far. Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-05[POWERPC] spufs: remove support for ancient firmwareArnd Bergmann
Any firmware that still uses the 'spc' nodes already stopped running for other reasons, so let's get rid of this. Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-05[POWERPC] spufs: make mailbox functions handle multiple elementsArnd Bergmann
Since libspe2 will provide a function that can read/write multiple mailbox elements at once, the kernel should handle that efficiently. read/write on the three mailbox files can now access the spe context multiple times to operate on any number of mailbox data elements. If the spu application keeps writing to its outbound mailbox, the read call will pick up all the data in a single system call. Unfortunately, if the user passes an invalid pointer, we may lose a mailbox element on read, since we can't put it back. This probably impossible to solve, if the user also accesses the mailbox through direct register access. Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-05[POWERPC] spufs: use correct pg_prot for mapping SPU local storeArnd Bergmann
This hopefully fixes a long-standing bug in the spu file system. An spu context comes with local memory that can be either saved in kernel pages or point directly to a physical SPE. When mapping the physical SPE, that mapping needs to be cache-inhibited. For simplicity, we used to map the kernel backing memory that way too, but unfortunately that was not only inefficient, but also incorrect because the same page could then be accessed simultaneously through a cacheable and a cache-inhibited mapping, which is not allowed by the powerpc specification and in our case caused data inconsistency for which we did a really ugly workaround in user space. Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>