| Age | Commit message (Collapse) | Author |
|---|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (124 commits)
sh: allow building for both r2d boards in same binary.
sh: fix r2d board detection
sh: Discard .exit.text/.exit.data at runtime.
sh: Fix up some section alignments in linker script.
sh: Fix SH-4 DMAC CHCR masking.
sh: Rip out left-over nommu cond syscall cruft.
sh: Make kgdb i-cache flushing less inept.
sh: kgdb section mismatches and tidying.
sh: cleanup struct irqaction initializers.
sh: early_printk tidying.
video: pvr2fb: Add TV (RGB) support to Dreamcast PVR driver.
sh: Conditionalize gUSA support.
sh: Follow gUSA preempt changes in __switch_to().
sh: Tidy up gUSA preempt handling.
sh: __copy_user() optimizations for small copies.
sh: clkfwk: Support multi-level clock propagation.
sh: Fix URAM start address on SH7785.
sh: Use boot_cpu_data for CPU probe.
sh: Support extended mode TLB on SH-X3.
sh: Bump MAX_ACTIVE_REGIONS for SH7785.
...
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] Don't take semaphore in cpufreq_quick_get()
[CPUFREQ] Support different families in fid/did to frequency conversion
[CPUFREQ] cpufreq_stats: misc cpuinit section annotations
[CPUFREQ] implement !CONFIG_CPU_FREQ stub for cpufreq_unregister_notifier()
[CPUFREQ] mark hotplug notifier callback as __cpuinit
[CPUFREQ] Only check for transition latency on problematic governors (kconfig fix)
[CPUFREQ] allow ondemand and conservative cpufreq governors to be used as default
[CPUFREQ] move policy's governor initialisation out of low-level drivers into cpufreq core
[CPUFREQ] Longhaul - Add support for PM133 northbridge
[CPUFREQ] x86: use num_online_nodes to get physical cpus numbers for
|
|
As noted by Christoph Hellwig, pktgen was the only user so
it can now be removed.
[ Add missing cases caught by Adrian Bunk. -DaveM ]
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These were previously discarded at link time, though as with MIPS
we keep them around until runtime to satisfy .rodata references.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
With the PERCPU() macro introduction .data.cacheline_aligned was
inhereting PAGE_SIZE alignment, fix that up for L1_CACHE_BYTES
again. Likewise, the initramfs section wants PAGE_SIZE alignment.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
into cpufreq core
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: Andi Kleen <ak@suse.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
At some point way back when (2.5 or so) quite a few syscalls hadn't
yet been wired up as cond_syscalls(), so we opted to just do direct
sys_ni_syscall wrapping in the assembly code instead. That's all
been fixed up since then, so we can drop the wrapping.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
kgdb had its own ranged I-cache flushing routine that attempted to
duplicate the flush_icache_range() functionality, but managed to do
an explicit D-cache writeback & invalidate twice on SH-4. This is
a no-op for SH-3, and the flush_icache_range() semantics already do
what kgdb was feebly attempting to do already, so just move over to
that and kill off the wrapper.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
The kgdb console setup was callable from a left-over deferred
initialization path, which in turn depends on __init symbols. Since
the deferred initialization was removed some time ago, kill off the
rest of those remnants and move kgdb_init() and friends to __init.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
setup_early_printk() can be static, and with that, we can kill off
the early initialization variable and move the CON_BOOT check in
to the function body.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This conditionalizes gUSA support. gUSA is not supported on
SMP configurations, and it's not necessary there anyways due
to having other atomicity options (ie, movli.l/movco.l).
Anything implementing the LL/SC semantics (all SH-4A CPUs)
can switch to userspace atomicity implementations without
requiring gUSA. This is left default-enabled on all UP so
that glibc doesn't break.
Those that know what they are doing can disable this explicitly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Currently gUSA toggles hardirqs to disable preemption in the signal
handler. Make the preemption toggling explicit, and kill off some
CONFIG_PREEMPT ifdefs in the process.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Currently clock propagation only works for one level, but we have some
clocks which need to propagate multiple levels, so make this recursive.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Not all of the SH-X2 URAM blocks are mapped in the same place,
SH7785 happens to map it on the opposite end of the address space
from SH7722, correct the addresses.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This moves off of smp_processor_id() and only sets the probe
information for the boot CPU directly. This will be copied out
for the secondaries, so there's no reason to do this each time.
This also allows for some header tidying.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
There was some debug code left in here that caused the pin changes
to never be hit. Kill that off, and all is well.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
The probing logic works for both URAM and L2, with no way to
distinguish between the two. Disable the probing for now and
let the CPU subtypes that have this in a real L2 configuration
explicitly say so.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
The uClinux MTD device uses _ebss, add the symbol and corresponding
export.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This adds basic support for SH-X3 SMP (4 CPUs).
More IPI and cache debugging is necessary, mostly interfacing the
d-cache coherency and the I-cache broadcast invalidates. Only for
testing at present!
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Now that the SMP stubs are in place, call in to the setup code
to be defined by the platform.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
There was a very preliminary bunch of SMP code scattered around for the
SH7604 microcontrollers from way back when, and it has mostly suffered
bitrot since then. With the tree already having been slowly getting
prepped for SMP, this plugs in most of the remaining platform-independent
bits.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This implements initial support for the SMP INTC (particularly
INTC2) controllers.
These are largely implemented as conventional blocks, with
register sets grouped together at fixed strides relative to
the CPU id.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This adds the TLB flushing routines for SMP systems, based on
the MIPS implementation, with some additional SH-specific
flush routines.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This consolidates the cpu_data definitions and gets rid of the special
boot_cpu_data. It's made a wrapper to the boot CPU, in order to keep
the existing in-tree users happy.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
The cpufreq driver banner is currently printed for each CPU, move
it down so it's not as noisy and it's only printed once.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Add SH7785 URAM as node 1, follows the SH-X3 change.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Get the SH7343 and SH7770 stuff linking again. Both of these still
require proper INTC support.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch contains the following fixes and improvements:
- Fix address typo for INTMSK2 / INTMSKCLR2 registers on sh7780.
- Adds IRQ_MODE_IRLnnnn_MASK using intc controller for IRL masking.
- Good old IRQ_MODE_IRLnnnn should not register any intc controller.
- plat_irq_setup_pins() now selects IRL or IRQ mode.
- the holding function is now disabled using ICR0.
By default all external pin interrupts are disabled.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
All processor specific interrupt code is now converted to make use
of the new intc code. The config option CONFIG_CPU_HAS_INTC_IRQ is
because of that pointless.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
CC arch/sh/kernel/cpu/sh4/sq.o
arch/sh/kernel/cpu/sh4/sq.c: In function 'sq_flush_range':
arch/sh/kernel/cpu/sh4/sq.c:65: warning: passing argument 1 of 'prefetch' discards qualifiers from pointer target type
This didn't actually need to be volatile in the first place, so just
kill off the qualifier entirely.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch converts the cpu specific interrupt setup code for sh7206
from ipr to intc. New vectors are also added to match the information
provided by the datasheet.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch converts the cpu specific interrupt setup code for sh7619
from ipr to intc. New vectors are also added to match the information
provided by the datasheet.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch makes sure the serial port interrupt irqs matches the
datasheet. Only irqs for SCIF1 are changed. While at some cosmetic
spaces are added.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch contains various intc fixes for problems reported by
Markus Brunner on the linuxsh-dev mailing list:
http://marc.info/?l=linuxsh-dev&m=118701948224991&w=1
Apart from added comments, the fixes are:
- add intc_set_priority() function prototype to hw_irq.h
- fix off-by-one error in intc_set_priority()
- make sure _INTC_WIDTH() is set for primary priority masking
Big thanks to Markus for finding these problems. Version two fixes
a compile error and an inverted primary check.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Markus Brunner <super.firetwister@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
With the intc core improved it is now possible to put the intc data
structures in the initdata section.
Version two of this patch puts the __initdata inside DECLARE_INTC_DESC()
and removes the __initdata included in the board specific r2d code.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
With the intc dual prio register support in place it is now possible
to add the ipi vectors to x3.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch reworks the intc core, implementing the following features:
- Support dual priority registers - one set and one clear register
- All 8/16/32 bit register combinations are now supported
- Both single mask and single enable bitmap register are supported
- Add code to set interrupt priority
- Speedup sense and priority configuration code
- Allocate data using bootmem, allows intc data structures to be
__initdata
- Save memory - allocated memory footprint is smaller than intc
structures
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
We need a secondary register member in struct intc_prio_reg to support
dual priority registers used by ipi on x3.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This makes sure the function prototype for setup_bootmem_node() gets
included. The file setup-shx3.c does not compile otherwise for
CONFIG_NUMA=n.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This adds support for the SH7720 (SH3-DSP) CPU.
Signed-off by: Markus Brunner <super.firetwister@gmail.com>
Signed-off by: Mark Jonas <toertel@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
synchronize_irq() was being exported twice, kill off the duplicate
export.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Now that NODES_SHIFT is bumped up, we can plug in the CSM block as
a separate node, too.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
IRL doesn't always define sense registers, so don't bother trying to
iterate through the table. This ended up causing an oops on SH-X3
when using IRL mode.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
There is no point in keeping around the now unused intc2 code.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch adds single bitmap register support to intc. The current
code only handles 16 and 32 bit registers where a set bit means
interrupt enabled, but this is easy to extend in the future.
The INTC_IRQ() macro is also added to provide a way to hook in
interrupt controllers for FPGAs in boards or companion chips.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch removes redundant interrupt code for the shmin board which
is using a sh770x processor and 4 IRQ lines as individual interrupts
(IRQ-mode).
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch removes redundant board specific interrupt code for boards
using sh775x processors and 4 IRQ lines in "Individual Interrupt Mode"
aka IRLM.
Three boards are affected: sh03, snapgear and titan.
The right way to do this is to use cpu specific code provided by intc.
A nice side effect is that sh03 now compiles, board not BROKEN any more.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
All SH-4 parts have a 4-digit year, while the SH-3 parts typically
only use a 2-digit one. The SH7705, SH7710, and SH7712 SH-3 parts
however opted to extend it to 4-digit and still look and act like
an SH-3 RTC in all other ways.
This adds a capability flag (RTC_CAP_4_DIGIT_YEAR) that these
corner-case CPU subtypes can set in their platform data and cleans
up some of the ifdef mess in the driver as a result.
Reported-by: Markus Brunner <super.firetwister@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
