| Age | Commit message (Collapse) | Author |
|---|
|
This is the arch/ part of the big kfree cleanup patch.
Remove pointless checks for NULL prior to calling kfree() in arch/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Reorganize the preempt_disable/enable calls to eliminate the extra preempt
depth. Changes based on Paul McKenney's review suggestions for the kprobes
RCU changeset.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Changes to the arch kprobes infrastructure to take advantage of the locking
changes introduced by usage of RCU for synchronization. All handlers are now
run without any locks held, so they have to be re-entrant or provide their own
synchronization.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Sparc64 changes to track kprobe execution on a per-cpu basis. We now track
the kprobe state machine independently on each cpu using an arch specific
kprobe control block.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The following set of patches are aimed at improving kprobes scalability. We
currently serialize kprobe registration, unregistration and handler execution
using a single spinlock - kprobe_lock.
With these changes, kprobe handlers can run without any locks held. It also
allows for simultaneous kprobe handler executions on different processors as
we now track kprobe execution on a per processor basis. It is now necessary
that the handlers be re-entrant since handlers can run concurrently on
multiple processors.
All changes have been tested on i386, ia64, ppc64 and x86_64, while sparc64
has been compile tested only.
The patches can be viewed as 3 logical chunks:
patch 1: Reorder preempt_(dis/en)able calls
patches 2-7: Introduce per_cpu data areas to track kprobe execution
patches 8-9: Use RCU to synchronize kprobe (un)registration and handler
execution.
Thanks to Maneesh Soni, James Keniston and Anil Keshavamurthy for their
review and suggestions. Thanks again to Anil, Hien Nguyen and Kevin Stafford
for testing the patches.
This patch:
Reorder preempt_disable/enable() calls in arch kprobes files in preparation to
introduce locking changes. No functional changes introduced by this patch.
Signed-off-by: Ananth N Mavinakayahanalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Andrew Morton suggested to move kprobes from kernel hacking menu, since
kernel hacking menu is in-appropriate for the Kprobes. This patch moves
Kprobes and Oprofile under instrumentation menu.
(akpm: it's not a natural fit, but things like djprobes and the s390 guys'
statistics library need a home)
Signed-of-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Cc: Philippe Elie <phil.el@wanadoo.fr>
Cc: John Levon <levon@movementarian.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Define jiffies_64 in kernel/timer.c rather than having 24 duplicated
defines in each architecture.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
TIOCSTART and TIOCSTOP are defined in asm/ioctls.h and asm/termios.h by
various architectures but not actually implemented anywhere but in the IRIX
compatibility layer, so remove their COMPATIBLE_IOCTL from parisc, ppc64
and sparc64.
Move the TIOCSLTC COMPATIBLE_IOCTL to common code, guided by an ifdef to
only show up on architectures that support it (same as the code handling it
in tty_ioctl.c), aswell as it's brother TIOCGLTC that wasn't handled so
far.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Convert those few architectures which are calling pud_alloc, pmd_alloc,
pte_alloc_map on a user mm, not to take the page_table_lock first, nor drop it
after. Each of these can continue to use pte_alloc_map, no need to change
over to pte_alloc_map_lock, they're neither racy nor swappable.
In the sparc64 io_remap_pfn_range, flush_tlb_range then falls outside of the
page_table_lock: that's okay, on sparc64 it's like flush_tlb_mm, and that has
always been called from outside of page_table_lock in dup_mmap.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Remove PageReserved() calls from core code by tightening VM_RESERVED
handling in mm/ to cover PageReserved functionality.
PageReserved special casing is removed from get_page and put_page.
All setting and clearing of PageReserved is retained, and it is now flagged
in the page_alloc checks to help ensure we don't introduce any refcount
based freeing of Reserved pages.
MAP_PRIVATE, PROT_WRITE of VM_RESERVED regions is tentatively being
deprecated. We never completely handled it correctly anyway, and is be
reintroduced in future if required (Hugh has a proof of concept).
Once PageReserved() calls are removed from kernel/power/swsusp.c, and all
arch/ and driver code, the Set and Clear calls, and the PG_reserved bit can
be trivially removed.
Last real user of PageReserved is swsusp, which uses PageReserved to
determine whether a struct page points to valid memory or not. This still
needs to be addressed (a generic page_is_ram() should work).
A last caveat: the ZERO_PAGE is now refcounted and managed with rmap (and
thus mapcounted and count towards shared rss). These writes to the struct
page could cause excessive cacheline bouncing on big systems. There are a
number of ways this could be addressed if it is an issue.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Refcount bug fix for filemap_xip.c
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
How is anon_rss initialized? In dup_mmap, and by mm_alloc's memset; but
that's not so good if an mm_counter_t is a special type. And how is rss
initialized? By set_mm_counter, all over the place. Come on, we just need to
initialize them both at once by set_mm_counter in mm_init (which follows the
memcpy when forking).
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
zap_pte_range has been counting the pages it frees in tlb->freed, then
tlb_finish_mmu has used that to update the mm's rss. That got stranger when I
added anon_rss, yet updated it by a different route; and stranger when rss and
anon_rss became mm_counters with special access macros. And it would no
longer be viable if we're relying on page_table_lock to stabilize the
mm_counter, but calling tlb_finish_mmu outside that lock.
Remove the mmu_gather's freed field, let tlb_finish_mmu stick to its own
business, just decrement the rss mm_counter in zap_pte_range (yes, there was
some point to batching the update, and a subsequent patch restores that). And
forget the anal paranoia of first reading the counter to avoid going negative
- if rss does go negative, just fix that bug.
Remove the mmu_gather's flushes and avoided_flushes from arm and arm26: no use
was being made of them. But arm26 alone was actually using the freed, in the
way some others use need_flush: give it a need_flush. arm26 seems to prefer
spaces to tabs here: respect that.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
tlb_is_full_mm? What does that mean? The TLB is full? No, it means that the
mm's last user has gone and the whole mm is being torn down. And it's an
inline function because sparc64 uses a different (slightly better)
"tlb_frozen" name for the flag others call "fullmm".
And now the ptep_get_and_clear_full macro used in zap_pte_range refers
directly to tlb->fullmm, which would be wrong for sparc64. Rather than
correct that, I'd prefer to scrap tlb_is_full_mm altogether, and change
sparc64 to just use the same poor name as everyone else - is that okay?
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Doing a "SUNW,stop-self" firmware call on the other cpus is not the
correct thing to do when dropping into the firmware for a halt,
reboot, or power-off.
For now, just do nothing to quiet the other cpus, as the system should
be quiescent enough. Later we may decide to implement smp_send_stop()
like the other SMP platforms do.
Based upon a report from Christopher Zimmermann.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The hairy fast allocator in the sparc64 PCI IOMMU code
has a hard limit of 256 pages. Certain devices can
exceed this when performing very large I/Os.
So replace with a more simple allocator, based largely
upon the arch/ppc64/kernel/iommu.c code.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All the PCI controller drivers were doing the same thing
setting up the IOMMU software state, put it all in one spot.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The sequence to move over to the Linux trap tables from
the firmware ones needs to be more air tight. It turns
out that to be %100 safe we do need to be able to translate
OBP mappings in our TLB miss handlers early.
In order not to eat up a lot of kernel image memory with
static page tables, just use the translations array in
the OBP TLB miss handlers. That solves the bulk of the
problem.
Furthermore, to make sure the OBP TLB miss path will work
even before the fixed MMU globals are loaded, explicitly
load %g1 to TLB_SFSR at the beginning of the i-TLB and
d-TLB miss handlers.
To ease the OBP TLB miss walking of the prom_trans[] array,
we sort it then delete all of the non-OBP entries in there
(for example, there are entries for the kernel image itself
which we're not interested in at all).
We also save about 32K of kernel image size with this change.
Not a bad side effect :-)
There are still some reasons why trampoline.S can't use the
setup_trap_table() yet. The most noteworthy are:
1) OBP boots secondary processors with non-bias'd stack for
some reason. This is easily fixed by using a small bootup
stack in the kernel image explicitly for this purpose.
2) Doing a firmware call via the normal C call prom_set_trap_table()
goes through the whole OBP enter/exit sequence that saves and
restores OBP and Linux kernel state in the MMUs. This path
unfortunately does a "flush %g6" while loading up the OBP locked
TLB entries for the firmware call.
If we setup the %g6 in the trampoline.S code properly, that
is in the PAGE_OFFSET linear mapping, but we're not on the
kernel trap table yet so those addresses won't translate properly.
One idea is to do a by-hand firmware call like we do in the
early bootup code and elsewhere here in trampoline.S But this
fails as well, as aparently the secondary processors are not
booted with OBP's special locked TLB entries loaded. These
are necessary for the firwmare to processes TLB misses correctly
up until the point where we take over the trap table.
This does need to be resolved at some point.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We were not doing alignment properly when remapping the kernel image.
What we want is a 4MB aligned physical address to map at KERNBASE.
Mistakedly we were 4MB aligning the virtual address where the kernel
initially sits, that's wrong.
Instead, we should PAGE align the virtual address, then 4MB align the
physical address result the prom gives to us.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On the boot processor, we need to do the move onto the Linux trap
table a little bit differently else we'll take unhandlable faults in
the firmware address space.
Previously we would do the following:
1) Disable PSTATE_IE in %pstate.
2) Set %tba by hand to sparc64_ttable_tl0
3) Initialize alternate, mmu, and interrupt global
trap registers.
4) Call prom_set_traptable()
That doesn't work very well actually with the way we boot the kernel
VM these days. It worked by luck on many systems because the firmware
accesses for the prom_set_traptable() call happened to be loaded into
the TLB already, something we cannot assume.
So the new scheme is this:
1) Clear PSTATE_IE in %pstate and set %pil to 15
2) Call prom_set_traptable()
3) Initialize alternate, mmu, and interrupt global
trap registers.
and this works quite well. This sequence has been moved into a
callable function in assembler named setup-trap_table(). The idea is
that eventually trampoline.S can use this code as well. That isn't
possible currently due to some complications, but eventually we should
be able to do it.
Thanks to Meelis Roos for the Ultra5 boot failure report.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
irq.c is missing the inclusion of asm/io.h, which causes
readb() and writeb() the be undefined.
Signed-off-by: Sven Hartge <hartge@ds9.argh.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need to use stricter memory barriers around the block
load and store instructions we use to save and restore the
FPU register file.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
By allocating early memory for the firmware page tables, we
can write over the beginning of the initrd image.
So what we do now is:
1) Read in firmware translations table while still on the
firmware's trap table.
2) Switch to Linux trap table.
3) Init bootmem.
4) Build firmware page tables using __alloc_bootmem().
And this keeps the initrd from being clobbered.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of code patching to handle the page size fields in
the context registers, just use variables from which we get
the proper values.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1) Use cpudata cache line sizes, not magic constants.
2) Align start address in cheetah case so we do not get
unaligned address traps. (pgrep was good at triggering
this, via /proc/${pid}/cmdline accesses)
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No longer used.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Delete all of the code working with sp_banks[] and replace
with clean acquisition and sorting of physical memory
parameters from the firmware.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Need to make sure the address is below high_memory before
passing it to kern_addr_valid().
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Thus, we can mark sp_banks[] static in arch/sparc64/mm/init.c
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Also, move prom_probe_memory() into arch/sparc64/mm/init.c
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of doing byte-at-a-time user accesses to figure
out where the fault occurred, read the saved fault_address
from the current thread structure.
For the sake of defensive programming, if the fault_address
does not fall into the user buffer range, simply assume the
whole area faulted. This will cause the fixup for
copy_from_user() to clear the entire kernel side buffer.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We were not calling kernel_mna_trap_fault() correctly.
Instead of being fancy, just return 0 vs. -EFAULT from
the assembler stubs, and handle that return value as
appropriate.
Create an "__retl_efault" stub for assembler exception
table entries and use it where possible.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The funny "range" exception table entries we had were only
used by the compat layer socketcall assembly, and it wasn't
even needed there.
For free we now get proper exception table sorting and fast
binary searching.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The in-memory value was being swapped, not the value we
loaded into the register.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Also, the us3_cpufreq driver can work on Ultra-IV and IV+.
They use the SAFARI bus register to control the clock divider
just like Ultra-III and III+ do.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to do it correctly on UltraSPARC-III+ and later we'd
need to add some complicated code to set the TAG access extension
register before loading the TLB.
Since this optimization gives questionable gains, it's best to
just remove it for now instead of adding the fix for Ultra-III+
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It tries to batch up the tag loads and comparisons, and
then the stores. And this is just complicated instead
of efficient.
Also, make the symbol of the Cheetah version more grepable.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At boot time, determine the D-cache, I-cache and E-cache size and
line-size. Use them in cache flushes when appropriate.
This change was motivated by discovering that the D-cache on
UltraSparc-IIIi and later are 64K not 32K, and the flushes done by the
Cheetah error handlers were assuming a 32K size.
There are still some pieces of code that are hard coding things and
will need to be fixed up at some point.
While we're here, fix the D-cache and I-cache parity error handlers
to run with interrupts disabled, and when the trap occurs at trap
level > 1 log the event via a counter displayed in /proc/cpuinfo.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The trick is that we do the kernel linear mapping TLB miss starting
with an instruction sequence like this:
ba,pt %xcc, kvmap_load
xor %g2, %g4, %g5
succeeded by an instruction sequence which performs a full page table
walk starting at swapper_pg_dir.
We first take over the trap table from the firmware. Then, using this
constant PTE generation for the linear mapping area above, we build
the kernel page tables for the linear mapping.
After this is setup, we patch that branch above into a "nop", which
will cause TLB misses to fall through to the full page table walk.
With this, the page unmapping for CONFIG_DEBUG_PAGEALLOC is trivial.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
"1" needs to be "1UL", this is a 64-bit mask we're creating.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'highest_paddr' is set, but never actually used.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of all of this cpu-specific code to remap the kernel
to the correct location, use portable firmware calls to do
this instead.
What we do now is the following in position independant
assembler:
chosen_node = prom_finddevice("/chosen");
prom_mmu_ihandle_cache = prom_getint(chosen_node, "mmu");
vaddr = 4MB_ALIGN(current_text_addr());
prom_translate(vaddr, &paddr_high, &paddr_low, &mode);
prom_boot_mapping_mode = mode;
prom_boot_mapping_phys_high = paddr_high;
prom_boot_mapping_phys_low = paddr_low;
prom_map(-1, 8 * 1024 * 1024, KERNBASE, paddr_low);
and that replaces the massive amount of by-hand TLB probing and
programming we used to do here.
The new code should also handle properly the case where the kernel
is mapped at the correct address already (think: future kexec
support).
Consequently, the bulk of remap_kernel() dies as does the entirety
of arch/sparc64/prom/map.S
We try to share some strings in the PROM library with the ones used
at bootup, and while we're here mark input strings to oplib.h routines
with "const" when appropriate.
There are many more simplifications now possible. For one thing, we
can consolidate the two copies we now have of a lot of cpu setup code
sitting in head.S and trampoline.S.
This is a significant step towards CONFIG_DEBUG_PAGEALLOC support.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Testing shows that the prom_unmap() calls do absolutely
nothing.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Because we don't access the PAGE_OFFSET linear mappings
any longer before we take over the trap table from the
firmware, we don't need to load dummy mappings there
into the TLB and we don't need the bootmap_base hack
any longer either.
While we are here, check for a larger than 8MB kernel
and halt the boot with an error message. We know that
doesn't work, so instead of failing mysteriously we
should let the user know exactly what's wrong.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Just allocate them physically starting from the end of
the kernel image. This incredibly simplifies our MM
bootstrap in that we don't need any mappings in the linear
PAGE_OFFSET area working in order to bootstrap ourselves and
take over the trap table from the firmware.
Many further simplifications are possible now, and this also
sets the stage for CONFIG_DEBUG_PAGEALLOC support.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This thing was just a huge monolithic mess, so chop it up.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
