| Age | Commit message (Collapse) | Author |
|---|
|
We have two conflicting DMA-based quirks in there for the same set of
boxes (HP nx6325 and nx6125) and one of them actually breaks my box.
So remove the extra code.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: =?iso-8859-1?q?T=F6r=F6k_Edwin?= <edwintorok@gmail.com>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
|
|
In the course of the recent unification of the NMI watchdog an assignment
to timer_ack to switch off unnecesary POLL commands to the 8259A in the
case of a watchdog failure has been accidentally removed. The statement
used to be limited to the 32-bit variation as since the rewrite of the
timer code it has been relevant for the 82489DX only. This change brings
it back.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
There is no such entity as ISA IRQ2. The ACPI spec does not make it
explicitly clear, but does not preclude it either -- all it says is ISA
legacy interrupts are identity mapped by default (subject to overrides),
but it does not state whether IRQ2 exists or not. As a result if there is
no IRQ0 override, then IRQ2 is normally initialised as an ISA interrupt,
which implies an edge-triggered line, which is unmasked by default as this
is what we do for edge-triggered I/O APIC interrupts so as not to miss an
edge.
To the best of my knowledge it is useless, as IRQ2 has not been in use
since the PC/AT as back then it was taken by the 8259A cascade interrupt
to the slave, with the line position in the slot rerouted to newly-created
IRQ9. No device could thus make use of this line with the pair of 8259A
chips. Now in theory INTIN2 of the I/O APIC may be usable, but the
interrupt of the device wired to it would not be available in the PIC mode
at all, so I seriously doubt if anybody decided to reuse it for a regular
device.
However there are two common uses of INTIN2. One is for IRQ0, with an
ACPI interrupt override (or its equivalent in the MP table). But in this
case IRQ2 is gone entirely with INTIN0 left vacant. The other one is for
an 8959A ExtINTA cascade. In this case IRQ0 goes to INTIN0 and if ACPI is
used INTIN2 is assumed to be IRQ2 (there is no override and ACPI has no
way to report ExtINTA interrupts). This is where a problem happens.
The problem is INTIN2 is configured as a native APIC interrupt, with a
vector assigned and the mask cleared. And the line may indeed get active
and inject interrupts if the master 8959A has its timer interrupt enabled
(it might happen for other interrupts too, but they are normally masked in
the process of rerouting them to the I/O APIC). There are two cases where
it will happen:
* When the I/O APIC NMI watchdog is enabled. This is actually a misnomer
as the watchdog pulses are delivered through the 8259A to the LINT0
inputs of all the local APICs in the system. The implication is the
output of the master 8259A goes high and low repeatedly, signalling
interrupts to INTIN2 which is enabled too!
[The origin of the name is I think for a brief period during the
development we had a capability in our code to configure the watchdog to
use an I/O APIC input; that would be INTIN2 in this scenario.]
* When the native route of IRQ0 via INTIN0 fails for whatever reason -- as
it happens with the system considered here. In this scenario the timer
pulse is delivered through the 8259A to LINT0 input of the local APIC of
the bootstrap processor, quite similarly to how is done for the watchdog
described above. The result is, again, INTIN2 receives these pulses
too. Rafael's system used to escape this scenario, because an incorrect
IRQ0 override would occupy INTIN2 and prevent it from being unmasked.
My conclusion is IRQ2 should be excluded from configuration in all the
cases and the current exception for ACPI systems should be lifted. The
reason being the exception not only being useless, but harmful as well.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Unlike the 32-bit one, the 64-bit variation of the LVT0 setup code for
the "8259A Virtual Wire" through the local APIC timer configuration does
not fully configure the relevant irq_chip structure. Instead it relies on
the preceding I/O APIC code to have set it up, which does not happen if
the I/O APIC variants have not been tried.
The patch includes corresponding changes to the 32-bit variation too
which make them both the same, barring a small syntactic difference
involving sequence of functions in the source. That should work as an aid
with the upcoming merge.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
IRQ0 is edge-triggered, but the "8259A Virtual Wire" through the local
APIC configuration in the 32-bit version uses the "fasteoi" handler
suitable for level-triggered APIC interrupt. Rewrite code so that the
"edge" handler is used. The 64-bit version uses different code and is
unaffected.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
The RING0_INT_FRAME macro defines a CFI_STARTPROC.
So we should really be using CFI_ENDPROC after it.
Signed-off-by: Glauber Costa <gcosta@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Add pseudo-feature bits to describe whether the CPU supports sysenter
and/or syscall from ia32-compat userspace. This removes a hardcoded
test in vdso32-setup.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Yinghai Lu reported crashes on 64-bit x86:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
IP: [<ffffffff80253b17>] hrtick_start_fair+0x89/0x173
[...]
And with a long session of debugging and a lot of difficulty, tracked it down
to this commit:
--------------->
8fbbc4b45ce3e4c0eeb15004c79c72b6896a79c2 is first bad commit
commit 8fbbc4b45ce3e4c0eeb15004c79c72b6896a79c2
Author: Alok Kataria <akataria@vmware.com>
Date: Tue Jul 1 11:43:34 2008 -0700
x86: merge tsc_init and clocksource code
<--------------
The problem is that the TSC unification missed these Makefile rules
in arch/x86/kernel/Makefile:
# Do not profile debug and lowlevel utilities
CFLAGS_REMOVE_tsc_64.o = -pg
CFLAGS_REMOVE_tsc_32.o = -pg
...
CFLAGS_tsc_64.o := $(nostackp)
...
which rules make sure that various instrumentation and debugging
facilities are disabled for code that might end up in a VDSO - such as
the TSC code.
Reported-and-bisected-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Conflicts:
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
when more than 4g memory is installed, don't map the big hole below 4g.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
to reserved
also let mem= to print out modified e820 map too
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Bernhard Walle <bwalle@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Integration generated a duplicate call to use_tsc_delay.
Particularly, the one that is done before we check for general
tsc usability seems wrong.
Signed-off-by: Glauber Costa <gcosta@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
fix:
arch/x86/kernel/visws_quirks.c: In function ‘visws_early_detect’:
arch/x86/kernel/visws_quirks.c:293: error: ‘no_broadcast’ undeclared (first use in this function)
arch/x86/kernel/visws_quirks.c:293: error: (Each undeclared identifier is reported only once
arch/x86/kernel/visws_quirks.c:293: error: for each function it appears in.)
make[1]: *** [arch/x86/kernel/visws_quirks.o] Error 1
make: *** [arch/x86/kernel/visws_quirks.o] Error 2
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
merge traps_visws.c and apic_visws.c into visws_quirks.c.
(no code changed)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
rename setup_visws.c to visws_quirks.c.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
skip IO-APIC setup on a VISWS if it's enabled.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
this is the big move: flip over VISWS to generic arch support.
From this commit on CONFIG_X86_VISWS is just another (default-disabled)
option that turns on certain quirks - no other complications.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
copy arch/x86/mach-visws/setup_visws.c, apic_visws.c and traps_visws.c
files to arch/x86/kernel/, in preparation of the switchover to a
non-subarch setup for VISWS.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
first step: make the VISWS subarch boot on a regular PC.
We take various shortcuts for that. We copy the generic arch setup file over
into the VISWS setup file.
This is the only step that is not expected to boot on a real VISWS.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Add early quirks support.
In preparation of enabling the generic architecture to boot on a VISWS.
This will allow us to remove the VISWS subarch and all its complications.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
When an interrupt is rerouted to a different I/O APIC pin the relevant
entry of the irq_2_pin list should get updated accordingly so that
operations are performed on the correct redirection entry.
This is already done by the 32-bit variation of the code and here is a
complementing 64-bit implementation. Should make someone's decision less
tough when merging the two. ;)
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
This reverts commit 90221a61a71b7ad659d8741cf1e404506b174982.
This too was just temporary diagnostics - not needed now that we've
got the final fix via:
| commit e2079c43861f71b2deb78ee20e247ad954fdd67e
| Author: Rafael J. Wysocki <rjw@sisk.pl>
| Date: Tue Jul 8 16:12:26 2008 +0200
|
| x86: fix C1E && nx6325 stability problem
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
This reverts commit a74a1cc3df0be89658bc735c8aed80c8392e2c15.
This was just temporary diagnostics commit - not needed now that we've
got the final fix.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
even on 64bit systems with less than 4G RAM, we can now use fixmap
to handle acpi SIT near end of ram.
change e820_end to e820_end_of_ram again?
or e820_ram_pfn?
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
and let 64-bit to fall back to use fixmap too.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
|
|
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: akpm@linux-foundation.org
Cc: andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
to avoid warning from find_low_pfn_range for high pages size etc
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
fix:
arch/x86/kernel/acpi/boot.c: In function ‘dmi_ignore_irq0_timer_override’:
arch/x86/kernel/acpi/boot.c:1443: error: implicit declaration of function ‘force_mask_ioapic_irq_2’
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
The problems are that, with the ACPI vs timer overring issue _fixed_,
after using the box for some time (between several seconds and 1 hour, at
random) processes get very high CPU loads (once I've got X using 107% of
the CPU, for example) and the system becomes unresponsive, as though there
were interrupts lost or something similar.
Andreas Herrman reproduced similar problems:
> Ok, now I've reproduced the stability problem.
> - Using tip/master,
> - reverting e38502eb8aa82314d5ab0eba45f50e6790dadd88 and
> - applying your patch from this posting
> http://marc.info/?l=linux-kernel&m=121539354224562&w=4
>
> Starting X, firefox, gimp, tuxpaint and doing some drawing in tuxpaint
> results in a slow system. Drawing is almost not possible anymore --
> Selections of new colors, cursors etc. is performed with huge delay
> if it's performed at all.
>
> BTW, the code sets up timer IRQ as Virtual Wire IRQ:
>
> Jul 8 14:57:58 kodscha IO-APIC (apicid-pin) 2-22, 2-23 not connected.
> Jul 8 14:57:58 kodscha ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
> Jul 8 14:57:58 kodscha ...trying to set up timer as Virtual Wire IRQ... works.
>
> and both INT0 and INT2 of IOAPIC are masked:
>
> Jul 8 14:57:58 kodscha NR Dst Mask Trig IRR Pol Stat Dmod Deli Vect:
> Jul 8 14:57:58 kodscha 00 000 1 0 0 0 0 0 0 00
> Jul 8 14:57:58 kodscha 01 003 0 0 0 0 0 1 1 31
> Jul 8 14:57:58 kodscha 02 003 1 0 0 0 0 0 0 30
>
> I've also seen strange CPU utilization -- with syslog-ng:
>
> top - 15:33:06 up 35 min, 4 users, load average: 1.70, 0.68, 0.37
> Tasks: 64 total, 4 running, 60 sleeping, 0 stopped, 0 zombie
> Cpu0 : 0.0%us,100.0%sy, 0.0%ni, 0.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st
> Cpu1 : 6.4%us, 87.2%sy, 0.0%ni, 5.8%id, 0.0%wa, 0.6%hi, 0.0%si, 0.0%st
> Mem: 895384k total, 283568k used, 611816k free, 35492k buffers
> Swap: 1959920k total, 0k used, 1959920k free, 163044k cached
>
> PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND
> 4632 root 20 0 17216 800 580 S 104 0.1 0:34.22 syslog-ng
> 28505 root 20 0 205m 11m 4024 S 6 1.3 0:21.16 X
> 28518 root 20 0 56292 5652 4492 S 1 0.6 0:01.80 fluxbox
> 1 root 20 0 3724 608 508 S 0 0.1 0:00.36 init
>
> So far I have no clue why C1E-idle in conjunction with virtual wire
> mode causes this strange behaviour.
>
> ... and I start to think about the root cause of all this.
>
> I've performed similar tests under X with the IRQ0/INT0 configuration and
> I did not see above symptoms.
So lets fall back to the IRQ0/INT0 configuration on this box.
This basically restores the dont-use-the-lapic-timer exception mechanism
that was unconditional on this box prior commit 8750bf5 ("x86: add C1E
aware idle function").
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
When system have 4g less ram installed, and acpi table sit
near end of ram, make max_pfn cover them too,
so 64bit kernel don't need to mess up fixmap.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: "Suresh Siddha" <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
This is for consistency with i386.
Signed-off-by: Glauber Costa <gcosta@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
This is for consistency with i386. We call use_tsc_delay()
at tsc initialization for x86_64, so we'll be always using it.
Signed-off-by: Glauber Costa <gcosta@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
arch/x86/kernel/smpboot.c: In function 'do_boot_cpu':
arch/x86/kernel/smpboot.c:943: warning: label 'restore_state' defined but not used
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
- order of local variable declarations
- minor code changes
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Acked-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
- local caching of smp_processor_id() in default_do_nmi()
- v2: do not split default_do_nmi over two lines
On Wed, Jul 02, 2008 at 08:12:20PM +0400, Cyrill Gorcunov wrote:
> | -static notrace __kprobes void default_do_nmi(struct pt_regs *regs)
> | +static notrace __kprobes void
> | +default_do_nmi(struct pt_regs *regs)
> | [ ... ]
> | -asmlinkage notrace __kprobes void default_do_nmi(struct pt_regs *regs)
> | +asmlinkage notrace __kprobes void
> | +default_do_nmi(struct pt_regs *regs)
>
> Hi Alexander, good done, thanks! But why did you split default_do_nmi
> definition by two lines? I think it would be better to keep them as it
> was before, ie by a single line
>
> static notrace __kprobes void default_do_nmi(struct pt_regs *regs)
Thanks! Here is the replacement patch with default_do_nmi left on
a single line.
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Acked-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
- if (cond) block -> if (!cond) goto end_of_block
- local caching of current
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Acked-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
if (cond) block -> if (!cond) goto end_of_block
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Acked-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
if (cond) block -> if (!cond) goto end_of_block
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Acked-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Reorder headers and collect globals in traps_32.c and traps_64.c
Code size and data size are unaffected by the changes. Code
itself is changed due to different ordering of data and bss.
The bss segment changed size due to a change in the packing
of the variables.
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Acked-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
This patch does not change the generated object files.
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Rename the paravirtualized calculate_cpu_khz to calibrate_tsc.
In all cases, we actually calibrate_tsc and use that as the cpu_khz value.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Signed-off-by: Dan Hecht <dhecht@vmware.com>
Cc: Dan Hecht <dhecht@vmware.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Unify the clocksource code.
Unify the tsc_init code.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Signed-off-by: Dan Hecht <dhecht@vmware.com>
Cc: Dan Hecht <dhecht@vmware.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Unify the TSC cpufreq code.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Signed-off-by: Dan Hecht <dhecht@vmware.com>
Cc: Dan Hecht <dhecht@vmware.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Merge the tsc calibration code for the 32bit and 64bit kernel.
The paravirtualized calculate_cpu_khz for 64bit now points to the correct
tsc_calibrate code as in 32bit.
Original native_calculate_cpu_khz for 64 bit is now called as calibrate_cpu.
Also moved the recalibrate_cpu_khz function in the common file.
Note that this function is called only from powernow K7 cpu freq driver.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Signed-off-by: Dan Hecht <dhecht@vmware.com>
Cc: Dan Hecht <dhecht@vmware.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Move the basic global variable definitions and sched_clock handling in the
common "tsc.c" file.
- Unify notsc kernel command line handling for 32 bit and 64bit.
- Functional changes for 64bit.
- "tsc_disabled" is updated if "notsc" is passed at boottime.
- Fallback to jiffies for sched_clock, incase notsc is passed on
commandline.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Signed-off-by: Dan Hecht <dhecht@vmware.com>
Cc: Dan Hecht <dhecht@vmware.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Add lapic resource into kernel resource map and mark it as busy
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
CC: Maciej W. Rozycki <macro@linux-mips.org>
|
|
Create page table entries to map the SGI UV chipset GRU. local MMR &
global MMR ranges.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: linux-mm@kvack.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
so when it is called after early_param, e820_saved get updated too.
esp for mpc update.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Bernhard Walle <bwalle@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
seperate reserve_setup_data into e820_reserved_setup_data,
and reserve_early_setup_data.
So could use e820_reserved_setup_data to backup e820 with setup_data.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Bernhard Walle <bwalle@suse.de>
Cc: Ying Huang <ying.huang@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
