| Age | Commit message (Collapse) | Author |
|---|
|
The recent Kconfig changes in x86 resulted in CONFIG_X86_HT no longer
being set if (X86_32 && MK8).
After grep'ing through the tree I think the problem is that different
places have different assumptions about the semantics of CONFIG_X86_HT,
either:
- hyperthreading or
- multicore
This should be sorted out properly, but until then we should keep the
2.6.23 status quo.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
pageexec@freemail.hu writes:
> i've just noticed that the chunk in i386/kernel/head.S ended up in a
> weird place, namely, it's not going to be executed as it's just after
> a 'jmp 3f' and before startup_32_smp, probably not what you intended.
> on a sidenote, the whole thing can be done in a single insn, like:
>
> movl $(swapper_pg_pmd - __PAGE_OFFSET + 0x067), (swapper_pg_dir -
> __PAGE_OFFSET+ 4092)
Thanks for the reminder I thought we had fixed this problem a while ago.
Needed to get fixed virtual address for USB debug and earlycon with mmio.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
we should also add hpet_disable() for kdump.
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
If HPET was enabled by pci quirks, we use i8253 as initial clockevent
because pci quirks doesn't run until pci is initialized.
The above means the kernel (or something) is assuming HPET legacy
replacement is disabled and can use i8253 at boot.
If we used kexec, it isn't true. So, this patch disables HPET legacy
replacement for kexec in machine_shutdown().
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hpa/linux-2.6-x86setup
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hpa/linux-2.6-x86setup:
x86 setup: don't recalculate ss:esp unless really necessary
|
|
Subdividing the paravirt_ops structure caused a regression in certain
non-GPL modules which try to use mmu_ops and cpu_ops. This restores the
old behaviour, and makes it consistent with the non-CONFIG_PARAVIRT case.
Takashi Iwai <tiwai@suse.de> adds:
> I took at this problem (as I have an nvidia card on one of my
> workstations), and found out that the following suffer from
> EXPORT_SYMBOL_GPL changes:
>
> * local_disable_irq(), local_irq_save*(), etc.
> * MSR-related macros like rdmsr(), wrmsr(), read_cr0(), etc.
> wbinvd(), too.
> * pmd_val(), pgd_val(), etc are all involved with pv_mm_ops.
> pmd_large() and pmd_bad() is also indirectly involved.
> __flush_tlb() and friends suffer, too.
Christoph Hellwig objects to this patch on the grounds that modules
shouldn't be using these operations anyway. I don't think this is a
particularly good reason to reject the patch, for several reasons:
1. These operations are still available to modules when not using
CONFIG_PARAVIRT, since they are implicitly exported as inline
functions via the kernel headers. Exporting the same functionality as
GPL-only symbols just adds a gratuitious difference between
CONFIG_PARAVIRT and non-CONFIG_PARAVIRT configurations. If we really
think these operations are not for module use (or non-GPL module use),
then we should solve the problem in a general way.
2. It's a regression from previous kernels, which would work these
modules even with CONFIG_PARAVIRT enabled.
3. The operations in question seem pretty reasonable for modules to
use. The control registers/MSRs can be accessed directly anyway, so there's
no benefit in preventing modules from using standard interfaces. And it seems
reasonable to allow a graphics driver to create its own mappings if it wants.
Therefore, I think this patch should go in for 2.6.24. If people
really think that these operations should not be available to modules,
then we can address that separately.
Signed-off-by: Jeremy Fitzhardinge <Jeremy.Fitzhardinge@citrix.com>
Cc: Tobias Powalowski <t.powa@gmx.de>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Keep lguest from being enabled on VISWS or VOYAGER configs, just as is
already done for VMI and XEN. Otherwise randconfigs with VISWS and LGUEST
have this problem:
In file included from arch/x86/kernel/setup_32.c:61:
include/asm-x86/mach-visws/setup_arch.h:8:1: warning: "ARCH_SETUP" redefined
In file included from include/asm/msr.h:80,
from include/asm/processor_32.h:17,
from include/asm/processor.h:2,
from include/asm/thread_info_32.h:16,
from include/asm/thread_info.h:2,
from include/linux/thread_info.h:21,
from include/linux/preempt.h:9,
from include/linux/spinlock.h:49,
from include/linux/seqlock.h:29,
from include/linux/time.h:8,
from include/linux/timex.h:57,
from include/linux/sched.h:53,
from arch/x86/kernel/setup_32.c:24:
include/asm/paravirt.h:458:1: warning: this is the location of the previous definition
(and of course, this happens because kconfig does not follow dependencies
when [evil] select is used...)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Changes __meminit to __init_refok.
WARNING: vmlinux.o(.text+0x1d07c): Section mismatch: reference to
.init.text:find_e820_area (between 'init_memory_mapping' and 'arch_add_memory')
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
_PAGE_PCD maps a page with caching disabled, which is typically used for
mapping harware registers. Xen never allows it to be set on a mapping, and
unprivileged guests never need it since they can't see the real underlying
hardware. However, some uncached mappings are made early when probing the
(non-existent) APIC, and its OK to mask off the PCD flag in these cases.
This became necessary because Xen started checking for this bit, rather
than silently masking it off.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In order to work around old LILO versions providing an invalid ss
register, the current setup code always sets up a new stack,
immediately following .bss and the heap. But this breaks LOADLIN.
This rewrite of the workaround checks for an invalid stack (ss!=ds)
first, and leaves ss:sp alone otherwise (apart from aligning esp).
[hpa note: LOADLIN has a number of arbitrary hard-coded limits that
are being pushed up against. Without some major revision of LOADLIN
itself it will not be sustainable keeping it alive. This gives it
another brief lease on life, however. This patch also helps the
cmdline truncation problem with old versions of SYSLINUX.]
Signed-off-by: Jens Rottmann <JRottmann at LiPPERT-AT. de>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86:
x86: fix APIC related bootup crash on Athlon XP CPUs
time: add ADJ_OFFSET_SS_READ
x86: export the symbol empty_zero_page on the 32-bit x86 architecture
x86: fix kprobes_64.c inlining borkage
pci: use pci=bfsort for HP DL385 G2, DL585 G2
x86: correctly set UTS_MACHINE for "make ARCH=x86"
lockdep: annotate do_debug() trap handler
x86: turn off iommu merge by default
x86: fix ACPI compile for LOCAL_APIC=n
x86: printk kernel version in WARN_ON and other dump_stack users
ACPI: Set max_cstate to 1 for early Opterons.
x86: fix NMI watchdog & 'stopped time' problem
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (39 commits)
ACPI: EC: Workaround for optimized controllers (version 3)
ACPI: EC: use printk_ratelimit(), add some DEBUG mode messages
Revert "ACPI: EC: Workaround for optimized controllers"
ACPI: fix two IRQ8 issues in IOAPIC mode
ACPI: Add missing spaces to printk format
cpuidle: fix HP nx6125 regression
cpuidle: add sched_clock_idle_[sleep|wakeup]_event() hooks
cpuidle: fix C3 for no bus-master control case
ACPI: thinkpad-acpi: fix oops when a module parameter has no value
Revert "Fix very high interrupt rate for IRQ8 (rtc) unless pnpacpi=off"
ACPI: EC: Don't init EC early if it has no _INI
Revert "acpi: make ACPI_PROCFS default to y"
Revert "ACPI: add documentation for deprecated /proc/acpi/battery in ACPI_PROCFS"
ACPI: Split out control for /proc/acpi entries from battery, ac, and sbs.
ACPI: Video: Increase buffer size for writes to brightness proc file.
ACPI: EC: Workaround for optimized controllers
ACPI: SBS: Fix retval warning
ACPI: Enable MSR (FixedHW) support for T-States
ACPI: Get throttling info from BIOS only after evaluating _PDC
ACPI: Use _TSS for throttling control, when present. Add error checks.
...
|
|
For a kernel built with "make ARCH=x86" the following system
information is displayed when running the new kernel
$ uname -m
x86
On some i386 systems (e.g. K7) we even have the following information
$ uname -m
x66
This is weird. The usual information for "uname -m" should be "x86_64"
on 64-bit and "i386" or "i686" on 32-bit.
This patch fixes the issue by setting UTS_MACHINE to "i386" for 32-bit
kernel builds and to "x86_64" for 64-bit kernel builds. I.e., "x86"
won't be used for UTS_MACHINE anymore.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andreas Herrmann <aherrman@arcor.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
warmbloodedcreature@gmail.com reported that an APIC-enabled
Asus a7v8x-x with an Athlon XP reboots early in the bootup:
http://bugzilla.kernel.org/show_bug.cgi?id=8723
after a long marathon of spontaneous-reboot debugging, it turns
out to be caused by sync_Arb_ids(). AMD CPUs never really needed
this sequence anyway, so just return early if we meet an AMD CPU.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The latest KVM driver wants to use the empty_zero_page symbol, and it's
not exported in 32-bit x86 (although it is exported by x86_64, s390, and
uml architectures).
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: tglx@linutronix.de
Cc: linux-kernel@vger.kernel.com
Cc: kvm-devel@lists.sourceforge.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
fix:
arch/x86/kernel/kprobes_64.c: In function 'set_current_kprobe':
arch/x86/kernel/kprobes_64.c:152: sorry, unimplemented: inlining failed in call to 'is_IF_modifier': recursive inlining
arch/x86/kernel/kprobes_64.c:166: sorry, unimplemented: called from here
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: mingo@elte.hu
Cc: akpm@linux-foundation.org
Cc: tglx@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
HP ProLiant systems DL385 G2 and DL585 G2 need pci=bfsort to enumerate PCI
devices in the expected order.
Matt sayeth:
biosdevname is a userspace app I wrote to help solve this so we don't need
to patch the kernel for future systems. It's not integrated into any
distributions properly yet, but is included in openSUSE 10.3 and Fedora 8
for people who want to download and install it there. It acts as a udev
helper.
For the time being, patching the kernel is necessary. I really hope
biosdevname eliminates that need in future distributions.
http://linux.dell.com/biosdevname/
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Andy Gospodarek <andy@greyhouse.net>
Cc: mingo@elte.hu
Cc: andy@greyhouse.net
Cc: john.cagle@hp.com
Cc: Matt Domsch <Matt_Domsch@dell.com>
Cc: Greg KH <greg@kroah.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
x86: correctly set UTS_MACHINE for "make ARCH=x86"
For a kernel built with "make ARCH=x86" the following system
information is displayed when running the new kernel
$ uname -m
x86
On some i386 systems (e.g. K7) we even have the following information
$ uname -m
x66
This is weird. The usual information for "uname -m" should be "x86_64"
on 64-bit and "i386" or "i686" on 32-bit.
This patch fixes the issue by setting UTS_MACHINE to "i386" for 32-bit
kernel builds and to "x86_64" for 64-bit kernel builds. I.e., "x86"
won't be used for UTS_MACHINE anymore.
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andreas Herrmann <aherrman@arcor.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@redhat.com>
|
|
Ensure the hardirq state is consistent before using locks. Use the rare
trace_hardirqs_fixup() because the trap can happen in any context.
resolves this rare lockdep warning:
WARNING: at kernel/lockdep.c:2658 check_flags()
[<c013571e>] check_flags+0x90/0x140
[<c0138a69>] lock_release+0x4b/0x1d0
[<c0507fea>] notifier_call_chain+0x2a/0x47
[<c050806b>] __atomic_notifier_call_chain+0x64/0x6d
[<c0508007>] __atomic_notifier_call_chain+0x0/0x6d
[<c050808b>] atomic_notifier_call_chain+0x17/0x1a
[<c0131802>] notify_die+0x30/0x34
[<c0506b09>] do_debug+0x3e/0xd4
[<c050658f>] debug_stack_correct+0x27/0x2c
[<c04be389>] tcp_rcv_established+0x1/0x620
[<c04c38c2>] tcp_v4_do_rcv+0x2b/0x313
[<c04c56b6>] tcp_v4_rcv+0x467/0x85d
[<c0505ff2>] _spin_lock_nested+0x27/0x32
[<c04c5a4d>] tcp_v4_rcv+0x7fe/0x85d
[<c04c560e>] tcp_v4_rcv+0x3bf/0x85d
[<c04adbb5>] ip_local_deliver_finish+0x11b/0x1b0
[<c04adac8>] ip_local_deliver_finish+0x2e/0x1b0
[<c04ada7b>] ip_rcv_finish+0x27b/0x29a
[<c04961e5>] netif_receive_skb+0xfb/0x2a6
[<c04add0f>] ip_rcv+0x0/0x1fb
[<c0496354>] netif_receive_skb+0x26a/0x2a6
[<c04961e5>] netif_receive_skb+0xfb/0x2a6
[<c049872e>] process_backlog+0x7f/0xc6
[<c04983ba>] net_rx_action+0xb9/0x1ac
[<c0498348>] net_rx_action+0x47/0x1ac
[<c01376cb>] trace_hardirqs_on+0x118/0x16b
[<c01225e2>] __do_softirq+0x49/0xa2
[<c010595f>] do_softirq+0x60/0xdd
[<c0506300>] _spin_unlock_irq+0x20/0x2c
[<c0103e4f>] restore_nocheck+0x12/0x15
[<c01440e1>] handle_fasteoi_irq+0x0/0x9b
[<c0105a70>] do_IRQ+0x94/0xaa
[<c0506300>] _spin_unlock_irq+0x20/0x2c
[<c0104832>] common_interrupt+0x2e/0x34
[<c0114703>] native_safe_halt+0x2/0x3
[<c0102c01>] default_idle+0x44/0x65
[<c010257f>] cpu_idle+0x42/0x50
[<c076ea09>] start_kernel+0x26b/0x270
[<c076e317>] unknown_bootoption+0x0/0x196
=======================
irq event stamp: 559190
hardirqs last enabled at (559190): [<c0507316>] kprobe_exceptions_notify+0x299/0x305
hardirqs last disabled at (559189): [<c05067bf>] do_int3+0x1d/0x95
softirqs last enabled at (559172): [<c010595f>] do_softirq+0x60/0xdd
softirqs last disabled at (559181): [<c010595f>] do_softirq+0x60/0xdd
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
revert this commit for now:
commit 948062683004d13ca21c8c05ac052d387978a449
Author: Andi Kleen <ak@suse.de>
Date: Fri Oct 19 20:35:03 2007 +0200
x86: enable iommu_merge by default
it's causing regressions:
http://bugzilla.kernel.org/show_bug.cgi?id=9412
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
today, all oopses contain a version number of the kernel, which is nice
because the people who actually do bother to read the oops get this
vital bit of information always without having to ask the reporter in
another round trip.
However, WARN_ON() and many other dump_stack() users right now lack this
information; the patch below adds this. This information is essential
for getting people to use their time effectively when looking at these
things; in addition, it's essential for tools that try to collect
statistics about defects.
Please consider, since its so simple and important for long term kernel
quality processes.
The code is identical between 32/64 bit; a lot of this code should be
unified over time, the patch keeps the identical-ness intact.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
More than 3 years ago Niclas Gustafsson reported a 'stopped time'
problem:
> Watching the /proc/interrupts with 10s apart after the "stop".
>
> [root@s151 root]# more /proc/interrupts
> CPU0
> 0: 66413955 local-APIC-edge timer
[...]
> LOC: 67355837
> ERR: 0
> MIS: 0
> [root@s151 root]# more /proc/interrupts
> CPU0
> 0: 66413955 local-APIC-edge timer
[...]
> LOC: 67379568
> ERR: 0
> MIS: 0
This may be because buggy SMM firmware messes with the 8259A (configured
for a transparent mode -- yes that rare "local-APIC-edge" mode is tricky
;-) ) insanely.
this should resolve:
http://bugzilla.kernel.org/show_bug.cgi?id=2544
http://bugzilla.kernel.org/show_bug.cgi?id=6296
Patch-dusted-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Conflicts:
drivers/acpi/ec.c
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
|
|
Use mp_irqs[] to get PNP device's interrupt polarity and trigger.
There are two reasons to do this:
1. BIOS bug for PNP interrupt
2. BIOS explictly does override
mp_irqs[] should cover all the cases.
http://bugzilla.kernel.org/show_bug.cgi?id=5243
http://bugzilla.kernel.org/show_bug.cgi?id=7679
http://bugzilla.kernel.org/show_bug.cgi?id=9153
[lenb: fixed !IOAPIC and 64-bit !SMP builds]
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Simplify "make ARCH=x86" and fix kconfig so we again
can set 64BIT in all.config.
For a fix the diffstat is nice:
6 files changed, 3 insertions(+), 36 deletions(-)
The patch reverts these commits:
0f855aa64b3f63d35a891510cf7db932a435c116
-> kconfig: add helper to set config symbol from environment variable
2a113281f5cd2febbab21a93c8943f8d3eece4d3
-> kconfig: use $K64BIT to set 64BIT with all*config targets
Roman Zippel pointed out that kconfig supported string
compares so the additional complexity introduced by the
above two patches were not needed.
With this patch we have following behaviour:
# make {allno,allyes,allmod,rand}config [ARCH=...]
option \ host arch | 32bit | 64bit
=====================================================
./. | 32bit | 64bit
ARCH=x86 | 32bit | 32bit
ARCH=i386 | 32bit | 32bit
ARCH=x86_64 | 64bit | 64bit
The general rule are that ARCH= and native architecture
takes precedence over the configuration.
So make ARCH=i386 [whatever] will always build a 32-bit
kernel no matter what the configuration says.
The configuration will be updated to 32-bit if it was
configured to 64-bit and the other way around.
This behaviour is consistent with previous behaviour so
no suprises here.
make ARCH=x86 will per default result in a 32-bit kernel
but as the only ARCH= value x86 allow the user to select
between 32-bit and 64-bit using menuconfig.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Andreas Herrmann <aherrman@arcor.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
|
|
Needed to make the wireless board, WRAP2C reboot.
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
need to check info->res_num less than PCI_BUS_NUM_RESOURCES, so
info->bus->resource[info->res_num] = res will not beyond of bus resource
array when acpi returns too many resource entries.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Gary Hade <gary.hade@us.ibm.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Some BIOSes advertise HPET at 0x0. We really do no want to
allocate a resource there. Check for it and leave early.
Other BIOSes tell us the HPET is at 0xfed0000000000000
instead of 0xfed00000. Add a check and fix it up with a warning
on user request.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Correct potentially unstable PC RTC time register reading in time_64.c
Stop the use of an incorrect technique for reading the standard PC RTC
timer, which is documented to "disconnect" time registers from the bus
while updates are in progress. The use of UIP flag while interrupts
are disabled to protect a 244 microsecond window is one of the
Motorola spec sheet's documented ways to read the RTC time registers
reliably.
tglx: removed locking changes from original patch, as they gain nothing
(read_persistent_clock is only called during boot, suspend, resume - so
no hot path affected) and conflict with the paravirt locking scheme
(see 32bit code), which we do not want to complicate for no benefit.
Signed-off-by: David P. Reed <dpreed@reed.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Fix hard freeze on x86_64 when the ntpd service calls
update_persistent_clock()
A repeatable but randomly timed freeze has been happening in Fedora 6
and 7 for the last year, whenever I run the ntpd service on my AMD64x2
HP Pavilion dv9000z laptop. This freeze is due to the use of
spin_lock(&rtc_lock) under the assumption (per a bad comment) that
set_rtc_mmss is called only with interrupts disabled. The call from
ntp.c to update_persistent_clock is made with interrupts enabled.
Signed-off-by: David P. Reed <dpreed@reed.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
92cb7612aee39642d109b8d935ad265e602c0563 sets cpu_info->cpu_index to zero
for no reason. Referencing cpu_info->cpu_index now points always to CPU#0,
which is apparently not what we want.
Remove it.
Spotted-by: Zou Nan hai <nanhai.zou@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Fix regressions introduced with 92cb7612aee39642d109b8d935ad265e602c0563.
It can happen that cpuinfo is displayed for CPUs that are not online or
even worse for CPUs not present at all. As an example, following was
shown for a "second" CPU of a single core K8 variant:
processor : 0
vendor_id : unknown
cpu family : 0
model : 0
model name : unknown
stepping : 0
cache size : 0 KB
fpu : yes
fpu_exception : yes
cpuid level : 0
wp : yes
flags :
bogomips : 0.00
clflush size : 0
cache_alignment : 0
address sizes : 0 bits physical, 0 bits virtual
power management:
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Commit d435d862baca3e25e5eec236762a43251b1e7ffc
("cpu hotplug: mce: fix cpu hotplug error handling")
changed the error handling in mce_cpu_callback.
In cases where not all CPUs are brought up during
boot (e.g. using maxcpus and additional_cpus parameters)
mce_cpu_callback now returns NOTFIY_BAD because
for such CPUs cpu_data is not completely filled when
the notifier is called. Thus mce_create_device fails right
at its beginning:
if (!mce_available(&cpu_data[cpu]))
return -EIO;
As a quick fix I suggest to check boot_cpu_data for MCE.
To reproduce this regression:
(1) boot with maxcpus=2 addtional_cpus=2 on a 4 CPU x86-64 system
(2) # echo 1 >/sys/devices/system/cpu/cpu2/online
-bash: echo: write error: Invalid argument
dmesg shows:
_cpu_up: attempt to bring up CPU 2 failed
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
dont use the vgetcpu tcache - it's causing problems with tasks
migrating, they'll see the old cache up to a jiffy after the
migration, further increasing the costs of the migration.
In the worst case they see a complete bogus information from
the tcache, when a sys_getcpu() call "invalidated" the cache
info by incrementing the jiffies _and_ the cpuid info in the
cache and the following vdso_getcpu() call happens after
vdso_jiffies have been incremented.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Fix Voyager section mismatch due to using __devinit instead of __cpuinit.
WARNING: vmlinux.o(.text+0xd943): Section mismatch: reference to .init.text:init_gdt (between 'voyager_smp_prepare_boot_cpu' and 'smp_vic_cmn_interrupt')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Fix Voyager section mismatches: voyager_cat_init() should be __init.
WARNING: vmlinux.o(.text+0xee83): Section mismatch: reference to .init.data:eprom_buf (between 'voyager_cat_init' and 'aes_enc_blk')
WARNING: vmlinux.o(.text+0xeea6): Section mismatch: reference to .init.data: (between 'voyager_cat_init' and 'aes_enc_blk')
WARNING: vmlinux.o(.text+0xeeac): Section mismatch: reference to .init.data: (between 'voyager_cat_init' and 'aes_enc_blk')
WARNING: vmlinux.o(.text+0xeeb2): Section mismatch: reference to .init.data: (between 'voyager_cat_init' and 'aes_enc_blk')
WARNING: vmlinux.o(.text+0xef4c): Section mismatch: reference to .init.data: (between 'voyager_cat_init' and 'aes_enc_blk')
WARNING: vmlinux.o(.text+0xef56): Section mismatch: reference to .init.data: (between 'voyager_cat_init' and 'aes_enc_blk')
WARNING: vmlinux.o(.text+0xf10f): Section mismatch: reference to .init.data:eprom_buf (between 'voyager_cat_init' and 'aes_enc_blk')
WARNING: vmlinux.o(.text+0xf13b): Section mismatch: reference to .init.data: (between 'voyager_cat_init' and 'aes_enc_blk')
WARNING: vmlinux.o(.text+0xf14b): Section mismatch: reference to .init.data: (between 'voyager_cat_init' and 'aes_enc_blk')
WARNING: vmlinux.o(.text+0xf159): Section mismatch: reference to .init.data: (between 'voyager_cat_init' and 'aes_enc_blk')
WARNING: vmlinux.o(.text+0xf1b1): Section mismatch: reference to .init.data:eprom_buf (between 'voyager_cat_init' and 'aes_enc_blk')
WARNING: vmlinux.o(.text+0xf1bb): Section mismatch: reference to .init.data: (between 'voyager_cat_init' and 'aes_enc_blk')
WARNING: vmlinux.o(.text+0xf1c1): Section mismatch: reference to .init.data:eprom_buf (between 'voyager_cat_init' and 'aes_enc_blk')
WARNING: vmlinux.o(.text+0xf1c7): Section mismatch: reference to .init.data:eprom_buf (between 'voyager_cat_init' and 'aes_enc_blk')
WARNING: vmlinux.o(.text+0xf1e6): Section mismatch: reference to .init.data: (between 'voyager_cat_init' and 'aes_enc_blk')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Add throttling control via MSR when T-states uses
the FixHW Control Status registers.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] Fix up whitespace in conservative governor.
[CPUFREQ] Make cpufreq_conservative handle out-of-sync events properly
[CPUFREQ] architectural pstate driver for powernow-k8
|
|
This patch fixes the following section mismatches with CONFIG_HOTPLUG=n:
<-- snip -->
...
WARNING: vmlinux.o(.data+0x23640): Section mismatch: reference to .init.text.20:can_skip_ioresource_align (between 'acpi_pciprobe_dmi_table' and 'pcibios_irq_mask')
WARNING: vmlinux.o(.data+0x2366c): Section mismatch: reference to .init.text.20:can_skip_ioresource_align (between 'acpi_pciprobe_dmi_table' and 'pcibios_irq_mask')
WARNING: vmlinux.o(.data+0x23698): Section mismatch: reference to .init.text.20:can_skip_ioresource_align (between 'acpi_pciprobe_dmi_table' and 'pcibios_irq_mask')
...
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
acpi_pci_link_exit() is both unused and empty.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/x86:
x86: enable "make ARCH=x86"
x86: do not use $(ARCH) when not needed
kconfig: use $K64BIT to set 64BIT with all*config targets
kconfig: add helper to set config symbol from environment variable
kconfig: factor out code in confdata.c
x86: move the rest of the menu's to Kconfig
x86: move all simple arch settings to Kconfig
x86: copy x86_64 specific Kconfig symbols to Kconfig.i386
x86: add X86_64 dependency to x86_64 specific symbols in Kconfig.x86_64
x86: add X86_32 dependency to i386 specific symbols in Kconfig.i386
x86: arch/x86/Kconfig.cpu unification
x86: start unification of arch/x86/Kconfig.*
x86: unification of cfufreq/Kconfig
|
|
Fix regression introduced with d435d862baca3e25e5eec236762a43251b1e7ffc
("cpu hotplug: mce: fix cpu hotplug error handling").
A CPU which was not brought up during boot (using maxcpus and
additional_cpus parameters) couldn't be onlined anymore. For such a CPU it
seemed that MCE was not supported during CPU_UP_PREPARE-time which caused
mce_cpu_callback to return NOTIFY_BAD to notifier_call_chain. To fix this
we:
- call mce_create_device for CPU_ONLINE event (instead of CPU_UP_PREPARE),
- avoid mce_remove_device() for the CPU that is not correctly initialized
by mce_create_device() failure,
- make mce_cpu_callback always return NOTIFY_OK for CPU_ONLINE event.
Because CPU_ONLINE callback return value is always ignored.
[akinobu.mita@gmail.com: avoid mce_remove_device() for not initialized device]
[akinobu.mita@gmail.com: make mce_cpu_callback always return NOTIFY_OK]
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Marin Mitov points out that delay_tsc() can misbehave if it is preempted and
rescheduled on a different CPU which has a skewed TSC. Fix it by disabling
preemption.
(I assume that the worst-case behaviour here is a stall of 2^32 cycles)
Cc: Andi Kleen <ak@suse.de>
Cc: Marin Mitov <mitov@issp.bas.bg>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
After unification of the Kconfig files and
introducing K64BIT support in kconfig
it required only trivial changes to enable
"make ARCH=x86".
With this patch you can build for x86_64 in several ways:
1) make ARCH=x86_64
2) make ARCH=x86 K64BIT=y
3) make ARCH=x86 menuconfig
=> select 64-bit
Likewise for i386 with the addition that
i386 is default is you say ARCH=x86.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
|
|
For x86 ARCH may say i386 or x86_64 and soon x86.
Rely on CONFIG_X64_32 to select between 32/64 or just
hardcode the value as appropriate.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
|
|
With this patch we have all the Kconfig file shared
between i386 and x86_64.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
|
|
Most of the arch settings were equal so combine them
in the first part of Kconfig.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
|
|
No functional changes.
A prepatory step towards full unification.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
|
|
To ease unification of Kconfig.i386 and Kconfig.x86_64
add X86_64 dependencies to all x86_64 specific symbols.
This patch introduce no functional changes but is one step
towards unification. This smaller step is used to ease
review of the patch set.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
|
