| Age | Commit message (Collapse) | Author |
|---|
|
Introduce the pm_power_off_prepare() callback that can be registered by the
interested platforms in analogy with pm_idle() and pm_power_off(), used for
preparing the system to power off (needed by ACPI).
This allows us to drop acpi_sysclass and device_acpi that are only defined in
order to register the ACPI power off preparation callback, which is needed by
pm_power_off() registered in a much different way.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Since we are now explicitly calling hibernation_ops->prepare() before
hibernation_ops->enter() in hibernation_platform_enter() (defined in
kernel/power/disk.c), ACPI should not call acpi_sleep_prepare(ACPI_STATE_S4)
from acpi_shutdown().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
At least on some machines it is necessary to prepare the ACPI firmware for the
restoration of the system memory state from the hibernation image if the
"platform" mode of hibernation has been used. Namely, in that cases we need
to disable the GPEs before replacing the "boot" kernel with the "frozen"
kernel (cf. http://bugzilla.kernel.org/show_bug.cgi?id=7887). After the
restore they will be re-enabled by hibernation_ops->finish(), but if the
restore fails, they have to be re-enabled by the restore code explicitly.
For this purpose we can introduce two additional hibernation operations,
called pre_restore() and restore_cleanup() and call them from the restore code
path. Still, they should be called if the "platform" mode of hibernation has
been used, so we need to pass the information about the hibernation mode from
the "frozen" kernel to the "boot" kernel in the image header.
Apparently, we can't drop the disabling of GPEs before the restore because of
Bug #7887 . We also can't do it unconditionally, because the GPEs wouldn't
have been enabled after a successful restore if the suspend had been done in
the 'shutdown' or 'reboot' mode.
In principle we could (and probably should) unconditionally disable the GPEs
before each snapshot creation *and* before the restore, but then we'd have to
unconditionally enable them after the snapshot creation as well as after the
restore (or restore failure) Still, for this purpose we'd need to modify
acpi_enter_sleep_state_prep() and acpi_leave_sleep_state() and we'd have to
introduce some mechanism synchronizing the disablind/enabling of the GPEs with
the device drivers' .suspend()/.resume() routines and with
disable_/enable_nonboot_cpus(). However, this would have affected the
suspend (ie. s2ram) code as well as the hibernation, which I'd like to avoid
in this patch series.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Nigel Cunningham <nigel@nigel.suspend2.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
[ With Johannes Berg <johannes@sipsolutions.net> ]
Separate the hibernation (aka suspend to disk code) from the other suspend
code. In particular:
* Remove the definitions related to hibernation from include/linux/pm.h
* Introduce struct hibernation_ops and a new hibernate() function to hibernate
the system, defined in include/linux/suspend.h
* Separate suspend code in kernel/power/main.c from hibernation-related code
in kernel/power/disk.c and kernel/power/user.c (with the help of
hibernation_ops)
* Switch ACPI (the only user of pm_ops.pm_disk_mode) to hibernation_ops
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Greg KH <greg@kroah.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Nigel Cunningham <nigel@nigel.suspend2.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove /proc/acpi/alarm file when the rtc-cmos "wakealarm" file is available.
Instead, provide hooks that rtc-cmos will use.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove software_suspend() and all its users since
pm_suspend(PM_SUSPEND_DISK) should be equivalent and there's no point in
having two interfaces for the same thing.
The patch also changes the valid_state function to return 0 (false) for
PM_SUSPEND_DISK when SOFTWARE_SUSPEND is not configured instead of
accepting it and having the whole thing fail later.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Almost all users of pm_ops only support mem sleep, don't check in .valid and
don't reject any others in .prepare so users can be confused if they check
/sys/power/state, especially when new states are added (these would then
result in s-t-r although they're supposed to be something different).
This patch implements a generic pm_valid_only_mem function that is then
exported for users and puts it to use in almost all existing pm_ops.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: linux-pm@lists.linux-foundation.org
Cc: Len Brown <lenb@kernel.org>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This updates /proc/acpi/wakeup to be more informative, primarily by showing
the sysfs node associated with each wakeup-enabled device. Example:
Device S-state Status Sysfs node
PCI0 S4 disabled no-bus:pci0000:00
PS2M S4 disabled pnp:00:05
PS2K S4 disabled pnp:00:06
UAR1 S4 disabled pnp:00:08
USB1 S3 disabled pci:0000:00:03.0
USB2 S3 disabled pci:0000:00:03.1
USB3 S3 disabled
USB4 S3 disabled pci:0000:00:03.3
S139 S4 disabled
LAN S4 disabled pci:0000:00:04.0
MDM S4 disabled
AUD S4 disabled pci:0000:00:02.7
SLPB S4 *enabled
Eventually this file should be removed, but until then it's almost the only
way we have to tell how the relevant ACPI tables are broken (and cope). In
that example, two devices don't actually exist (USB3, S139), one can't issue
wakeup events (PCI0), and two seem harmlessly (?) confused (MDM and AUD are
the same PCI device, but it's the _modem_ that does wake-on-ring).
In particular, we need to be sure driver model nodes are properly hooked
up before we can get rid of this ACPI-only interface for wakeup events.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
|
|
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
late_initcall() is too late for acpi_sleep_init().
Call it directly from acpi_init code.
http://bugzilla.kernel.org/show_bug.cgi?id=7887
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@linux.intel.com>
Signed-off-by: Vladimir Lebedev <vladimir.p.lebedev@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Fixing wrong description for acpi_gpe_sleep_prepare().
acpi_gpe_sleep_prepare() had only used on power off and was changed
to also used on entering some sleep state. However its description
isn't changed yet.
Signed-off-by: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
|
|
http://bugzilla.kernel.org/show_bug.cgi?id=6612
Note that this fix depends on a fix in ACPICA 20060608
to replace a semaphore with a spin-lock.
Signed-off-by: Arnaud Patard <apatard@mandriva.com>
Acked-by: "Yu, Luming" <luming.yu@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Internal BIOS names like these should be exposed
to the user as little as possible:
ACPI wakeup devices: C069 C0CE C1D1 C0DE C1D4
Eventually, the "wakeup" property of a device should be exported via the
device tree, not by a printk of an internal BIOS name. For the hard-core,
these are still available in /proc/acpi/wakeup_devices, just not
printed to dmesg.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
http://bugzilla.kernel.org/show_bug.cgi?id=4320
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Add pm_ops.valid callback, so only the available pm states show in
/sys/power/state. And this also makes an earlier states error report at
enter_state before we do actual suspend/resume.
Signed-off-by: Shaohua Li<shaohua.li@intel.com>
Acked-by: Pavel Machek<pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Remove S4BIOS support. It is pretty useless, and only ever worked for _me_
once. (I do not think anyone else ever tried it). It was in feature-removal
for a long time, and it should have been removed before.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
When acpi_sleep_prepare was moved into a shutdown method we
started calling it for all shutdowns.
It appears this triggers some systems to power off on reboot.
Avoid this by only calling acpi_sleep_prepare if we are going to power
off the system.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Now that all of the code paths that call acpi_power_off
have been modified to call either call kernel_power_off
(which calls apci_sleep_prepare by way of acpi_shutdown)
or to call acpi_sleep_prepare directly it is redundant to call
acpi_sleep_prepare from acpi_power_off.
So simplify the code and simply don't call acpi_sleep_prepare.
In addition there is a little error handling done so if we
can't register the acpi class we don't hook pm_power_off.
I think I have done the right thing with the CONFIG_PM define
but I'm not certain. Can this code even be compiled if
CONFIG_PM is false?
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
machine_power_off on i386 and x86_64 now switch to the
boot cpu out of paranoia and because the MP Specification indicates it
is a good idea on reboot, so for those architectures it is a noop.
I can't see anything in the acpi spec that requires you to be on
the boot cpu to power off the system, so this should not be an issue
for ia64. In addition ia64 has the altix a massive multi-node
system where switching to the boot cpu sounds insane as we may
hot removed the boot cpu.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Register an "acpi" system device to be notified of shutdown preparation.
This depends on CONFIG_PM
http://bugzilla.kernel.org/show_bug.cgi?id=4041
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
|
