aboutsummaryrefslogtreecommitdiff
path: root/drivers/ata/libata-sff.c
AgeCommit message (Collapse)Author
2009-03-24[libata] Improve timeout handlingAlan Cox
On a timeout call a device specific handler early in the recovery so that we can complete and process successful commands which timed out due to IRQ loss or the like rather more elegantly. [Revised to exclude the timeout handling on a few devices that inherit from SFF but are not SFF enough to use the default timeout handler] Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-03-24[libata] Drain data on errorsAlan Cox
If the device is signalling that there is data to drain after an error we should read the bytes out and throw them away. Without this some devices and controllers get wedged and don't recover. Based on earlier work by Mark Lord Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-03-13libata: Keep shadow last_ctl up to date during resetsStuart MENEFY
libata keeps a shadow copy of the ATA CTL register (which is write only), and only writes to the hardware when the required value doesn't match the shadow. However this copy wasn't being maintained when performing reset functions. This could cause problems for the first operation after a reset when the correct value might not be written to the CTL register. This problem was observed when hotplugging a drive: the identify command was being issued with interrupts enabled, when they should have been disabled. Signed-off-by: Stuart Menefy <stuart.menefy@st.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-02-16libata-sff: fix 32-bit PIO ATAPI regressionSergei Shtylyov
Commit 871af1210f13966ab911ed2166e4ab2ce775b99d (libata: Add 32bit PIO support) has caused all kinds of errors on the ATAPI devices, so it has been empirically proven that one shouldn't try to read/write an extra data word when a device is not expecting it already. "Don't do it then"; however, still use a chance to do 32-bit read/write one last time when there are exactly 3 trailing bytes. Oh, and stop pointlessly swapping the bytes to and fro on big-endian machines by using io*_rep() accessors which shouldn't byte-swap. This patch should fix the kernel.org bug #12609. Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-26libata: set NODEV_HINT for 0x7f statusTejun Heo
Asus Pundit-R with atiixp controller has the second port missing and, very unusually, its status is stuck at 0x7f and all others at 0. This meanst that it fails TF access test but gets detected as a disk due to classification code check and then evades polling IDENTIFY presence detection thanks to the missing BSY in the status value causing excessive delays during boot. This patch makes libata-sff HSM set NODEV_HINT if the status is 0x7f to make polling IDENTIFY presence detection work for these machines. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-26libata-sff: fix incorrect EH messageTejun Heo
The EH message for NODEV_HINT path was describing the opposite condition. Fix it. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-13ata: fix wrong WARN_ON_ONCEChristian Borntraeger
This patch fixes a wrong WARN_ON that was triggered by 32bit PIO support: WARNING: at drivers/ata/libata-sff.c:1017 ata_sff_hsm_move+0x45e/0x750() __atapi_pio_bytes simply doesnt know enough to decide if there is a bug. Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-09libata: use WARN_ON_ONCE on hot pathsTejun Heo
Convert WARN_ON() on command issue/completion paths to WARN_ON_ONCE() so that libata doesn't spam the machine even when one of those conditions triggers repeatedly. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-01-08libata: clean up the SFF code for coding styleAlan Cox
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-08libata: Add 32bit PIO supportAlan Cox
This matters for some controllers and in one or two cases almost doubles PIO performance. Add a bmdma32 operations set we can inherit and activate it for some controllers Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-14libata: improve phantom device detectionTejun Heo
Currently libata uses four methods to detect device presence. 1. PHY status if available. 2. TF register R/W test (only promotes presence, never demotes) 3. device signature after reset 4. IDENTIFY failure detection in SFF state machine Combination of the above works well in most cases but recently there have been a few reports where a phantom device causes unnecessary delay during probe. In both cases, PHY status wasn't available. In one case, it passed #2 and #3 and failed IDENTIFY with ATA_ERR which didn't qualify as #4. The other failed #2 but as it passed #3 and #4, it still caused failure. In both cases, phantom device reported diagnostic failure, so these cases can be safely worked around by considering any !ATA_DRQ IDENTIFY failure as NODEV_HINT if diagnostic failure is set. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-22libata-sff: fix ata_sff_post_internal_cmd()Tejun Heo
ata_sff_post_internal_cmd() needs to grab port lock before calling ata_bmdma_stop() and also need to clear hsm_task_state. Fix it. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-08libata-sff: kill spurious WARN_ON() in ata_hsm_move()Tejun Heo
On HSM_ST_ERR, ata_hsm_move() triggers WARN_ON() if AC_ERR_DEV or AC_ERR_HSM is not set. PHY events may trigger HSM_ST_ERR with other error codes and, with or without it, there just isn't much reason to do WARN_ON() on it. Even if error code is not set there, core EH logic won't have any problem dealing with the error condition. OSDL bz#11065 reports this problem. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-14libata: consistently use msecs for time durationsTejun Heo
libata has been using mix of jiffies and msecs for time druations. This is getting confusing. As writing sub HZ values in jiffies is PITA and msecs_to_jiffies() can't be used as initializer, unify unit for all time durations to msecs. So, durations are in msecs and deadlines are in jiffies. ata_deadline() is added to compute deadline from a start time and duration in msecs. While at it, drop now superflous _msec suffix from arguments and rename @timeout to @deadline if it represents a fixed point in time rather than duration. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-04libata-sff: improve HSM violation reportingTejun Heo
Improve SFF HSM violation reporting such that each HSM violation can be distinguished using ehi_desc. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-05libata: fix G5 SATA broken on -rc5Hugh Dickins
Fix G5 SATA irq 18: nobody cared, reported on -rc5 by Olaf Hering: fixlet to a57c1bade5a0ee5cd8b74502db9cbebb7f5780b2 libata-sff: Fix oops reported in kerneloops.org for pnp devices with no ctl Signed-off-by: Hugh Dickins <hugh@veritas.com> Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Tested-by: Olaf Hering <olaf@aepfle.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-06-04libata-sff: Fix oops reported in kerneloops.org for pnp devices with no ctlAlan Cox
- Make ata_sff_altstatus private so nobody uses it by mistake - Drop the 400nS delay from it Add ata_sff_irq_status - encapsulates the IRQ check logic This function keeps the existing behaviour for altstatus using devices. I actually suspect the logic was wrong before the changes but -rc isn't the time to play with that ata_sff_sync - ensure writes hit the device Really we want an io* operation for 'is posted' eg ioisposted(ioaddr) so that we can fix the nasty delay this causes on most systems. - ata_sff_pause - 400nS delay Ensure the command hit the device and delay 400nS - ata_sff_dma_pause Ensure the I/O hit the device and enforce an HDMA1:0 transition delay. Requires altstatus register exists, BUG if not so we don't risk corruption in MWDMA modes. (UDMA the checksum will save your backside in theory) The only other complication then is devices with their own handlers. rb532 can use dma_pause but scc needs to access its own altstatus register for internal errata workarounds so directly call the drivers own altstatus function. Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06libata: improve post-reset device ready testTejun Heo
Some controllers (jmb and inic162x) use 0x77 and 0x7f to indicate that the device isn't ready yet. It looks like they use 0xff if device presence is detected but connection isn't established. 0x77 or 0x7f after connection is established and use the value from signature FIS after receiving it. This patch implements ata_check_ready(), which takes TF status value and determines whether the port is ready or not considering the above and other conditions, and use it in @check_ready() functions. This is safe as both 0x77 and 0x7f aren't valid ready status value even though they have BSY bit cleared. This fixes hot plug detection failures which can be triggered with certain drives if they aren't already spun up when the data connector is hot plugged. Tested on sil, sil24, ahci (jmb/ich), piix and inic162x combined with eight drives from all major vendors. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-25libata: make WARN_ON conditions in ata_sff_hsm_move() more strictTejun Heo
WARN_ON()'s in ata_hsm_move() was too liberal and got triggerred when it shouldn't (e.g. hotplug events at the right moment). As the HSM only deals with device errors and state machine violations, make it check only against them. Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Mark Lord <liml@rtr.ca> Cc: Albert Lee <albertcc@tw.ibm.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17libata: move link onlineness check out of softreset methodsTejun Heo
Currently, SATA softresets should do link onlineness check before actually performing SRST protocol but it doesn't really belong to softreset. This patch moves onlineness check in softreset to ata_eh_reset() and ata_eh_followup_srst_needed() to clean up code and help future sata_mv changes which need clear separation between SCR and TF accesses. sata_fsl is peculiar in that its softreset really isn't softreset but combination of hardreset and softreset. This patch adds dummy private ->prereset to keep the current behavior but the driver really should implement separate hard and soft resets and return -EAGAIN from hardreset if it should be follwed by softreset. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17libata: replace tf_read with qc_fill_rtf for non-SFF driversTejun Heo
Now that all SFF stuff is separated out of core layer, core layer doesn't call ops->tf_read directly. It gets called only via ops->qc_fill_rtf() for non-SFF drivers. This patch directly implements private ops->qc_fill_rtf() for non-SFF controllers and kill ops->tf_read(). This is much cleaner for non-SFF controllers as some of them have to cache SFF register values in private data structure and report the cached values via ops->tf_read(). Also, ops->tf_read() gets nasty for controllers which don't have clear notion of TF registers when operation is not in progress. As this change makes default ops->qc_fill_rtf unnecessary, move ata_sff_qc_fill_rtf() form ata_base_port_ops to ata_sff_port_ops where it belongs. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17libata: add qc_fill_rtf port operationTejun Heo
On command completion, ata_qc_complete() directly called ops->tf_read to fill qc->result_tf. This patch adds ops->qc_fill_rtf to replace hardcoded ops->tf_read usage. ata_sff_qc_fill_rtf() which uses ops->tf_read to fill result_tf is implemented and set in ata_base_port_ops and other ops tables which don't inherit from ata_base_port_ops, so this patch doesn't introduce any behavior change. ops->qc_fill_rtf() is similar to ops->sff_tf_read() but can only be called when a command finishes. As some non-SFF controllers don't have TF registers defined unless they're associated with in-flight commands, this limited operation makes life easier for those drivers and help lifting SFF assumptions from libata core layer. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17libata: unify mechanism to request follow-up SRSTTejun Heo
Previously, there were two ways to trigger follow-up SRST from hardreset method - returning -EAGAIN and leaving all device classes unmodified. Drivers never used the latter mechanism and the only use case for the former was when hardreset couldn't classify. Drop the latter mechanism and let -EAGAIN mean "perform follow-up SRST if classification is required". This change removes unnecessary follow-up SRSTs and simplifies reset implementations. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17libata: implement and use sata_std_hardreset()Tejun Heo
Implement sata_std_hardreset(), which simply wraps around sata_link_hardreset(). sata_std_hardreset() becomes new standard hardreset method for sata_port_ops and sata_sff_hardreset() moves from ata_base_port_ops to ata_sff_port_ops, which is where it really belongs. ata_is_builtin_hardreset() is added so that both ata_std_error_handler() and ata_sff_error_handler() skip both builtin hardresets if SCR isn't accessible. piix_sidpr_hardreset() in ata_piix.c is identical to sata_std_hardreset() in functionality and got replaced with the standard function. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17libata: move generic hardreset code from sata_sff_hardreset() to ↵Tejun Heo
sata_link_hardreset() sata_sff_hardreset() contains link readiness wait logic which isn't SFF specific. Move that part into sata_link_hardreset(), which now takes two more parameters - @online and @check_ready. Both are optional. The former is out parameter for link onlineness after reset. The latter is used to wait for link readiness after hardreset. Users of sata_link_hardreset() is updated to use new funtionality and ahci_hardreset() is updated to use sata_link_hardreset() instead of sata_sff_hardreset(). This doesn't really cause any behavior change. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17libata: separate out ata_wait_ready() and implement ata_wait_after_reset()Tejun Heo
Factor out waiting logic (which is common to all ATA controllers) from ata_sff_wait_ready() into ata_wait_ready(). ata_wait_ready() takes @check_ready function pointer and uses it to poll for readiness. This allows non-SFF controllers to use ata_wait_ready() to wait for link readiness. This patch also implements ata_wait_after_reset() - generic version of ata_sff_wait_after_reset() - using ata_wait_ready(). ata_sff_wait_ready() is reimplemented using ata_wait_ready() and ata_sff_check_ready(). Functionality remains the same. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17libata: restructure SFF post-reset readiness waitsTejun Heo
Previously, post-softreset readiness is waited as follows. 1. ata_sff_wait_after_reset() waits for 150ms and then for ATA_TMOUT_FF_WAIT if status is 0xff and other conditions meet. 2. ata_bus_softreset() finishes with -ENODEV if status is still 0xff. If not, continue to #3. 3. ata_bus_post_reset() waits readiness of dev0 and/or dev1 depending on devmask using ata_sff_wait_ready(). And for post-hardreset readiness, 1. ata_sff_wait_after_reset() waits for 150ms and then for ATA_TMOUT_FF_WAIT if status is 0xff and other conditions meet. 2. sata_sff_hardreset waits for device readiness using ata_sff_wait_ready(). This patch merges and unifies post-reset readiness waits into ata_sff_wait_ready() and ata_sff_wait_after_reset(). ATA_TMOUT_FF_WAIT handling is merged into ata_sff_wait_ready(). If TF status is 0xff, link status is unknown and the port is SATA, it will continue polling till ATA_TMOUT_FF_WAIT. ata_sff_wait_after_reset() is updated to perform the following steps. 1. waits for 150ms. 2. waits for dev0 readiness using ata_sff_wait_ready(). Note that this is done regardless of devmask, as ata_sff_wait_ready() handles 0xff status correctly, this preserves the original behavior except that it may wait longer after softreset if link is online but status is 0xff. This behavior change is very unlikely to cause any actual difference and is intended. It brings softreset behavior to that of hardreset. 3. waits for dev1 readiness just the same way ata_bus_post_reset() did. Now both soft and hard resets call ata_sff_wait_after_reset() after reset to wait for readiness after resets. As ata_sff_wait_after_reset() contains calls to ->sff_dev_select(), explicit call near the end of sata_sff_hardreset() is removed. This change makes reset implementation simpler and more consistent. While at it, make the magical 150ms wait post-reset wait duration a constant and ata_sff_wait_ready() and ata_sff_wait_after_reset() take @link instead of @ap. This is to make them consistent with other reset helpers and ease core changes. pata_scc is updated accordingly. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17libata: separate out ata_std_postreset() from ata_sff_postreset()Tejun Heo
Separate out generic ATA portion from ata_sff_postreset() into ata_std_postreset() and implement ata_sff_postreset() using the std version. ata_base_port_ops now has ata_std_postreset() for its postreset and ata_sff_port_ops overrides it to ata_sff_postreset(). This change affects pdc_adma, ahci, sata_fsl and sata_sil24. pdc_adma now specifies postreset to ata_sff_postreset() explicitly. sata_fsl and sata_sil24 now use ata_std_postreset() which makes no difference to them. ahci now calls ata_std_postreset() from its own postreset method, which causes no behavior difference. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17libata: separate out ata_std_prereset() from ata_sff_prereset()Tejun Heo
Separate out generic ATA portion from ata_sff_prereset() into ata_std_prereset() and implement ata_sff_prereset() using the std version. Waiting for device readiness is the only SFF specific part. ata_base_port_ops now has ata_std_prereset() for its prereset and ata_sff_port_ops overrides it to ata_sff_prereset(). This change can affect pdc_adma, ahci, sata_fsl and sata_sil24. pdc_adma implements its own prereset using ata_sff_prereset() and the rest has hardreset and thus are unaffected by this change. This change reflects real world situation. There is no generic way to wait for device readiness for non-SFF controllers and some of them don't have any mechanism for that. Non-sff drivers which don't have hardreset should wrap ata_std_prereset() and wait for device readiness itself but there's no such driver now and isn't likely to be popular in the future either. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17libata: clean up port_ops->sff_irq_clear()Tejun Heo
->sff_irq_clear() is called only from SFF interrupt handler, so there is no reason to initialize it for non-SFF controllers. Also, ata_sff_irq_clear() can handle both BMDMA and non-BMDMA SFF controllers. This patch kills ata_noop_irq_clear() and removes it from base port_ops and sets ->sff_irq_clear to ata_sff_irq_clear() in sff port_ops instead of bmdma port_ops. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17libata: rename SFF port opsTejun Heo
Add sff_ prefix to SFF specific port ops. This rename is in preparation of separating SFF support out of libata core layer. This patch strictly renames ops and doesn't introduce any behavior difference. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17libata: rename SFF functionsTejun Heo
SFF functions have confusing names. Some have sff prefix, some have bmdma, some std, some pci and some none. Unify the naming by... * SFF functions which are common to both BMDMA and non-BMDMA are prefixed with ata_sff_. * SFF functions which are specific to BMDMA are prefixed with ata_bmdma_. * SFF functions which are specific to PCI but apply to both BMDMA and non-BMDMA are prefixed with ata_pci_sff_. * SFF functions which are specific to PCI and BMDMA are prefixed with ata_pci_bmdma_. * Drop generic prefixes from LLD specific routines. For example, bfin_std_dev_select -> bfin_dev_select. The following renames are noteworthy. ata_qc_issue_prot() -> ata_sff_qc_issue() ata_pci_default_filter() -> ata_bmdma_mode_filter() ata_dev_try_classify() -> ata_sff_dev_classify() This rename is in preparation of separating SFF support out of libata core layer. This patch strictly renames functions and doesn't introduce any behavior difference. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17libata/pdc_adma: make SFF EH handle non-bmdma SFF drivers and standardize ↵Tejun Heo
pdc_adma ops pdc_adma has interface similar to SFF but has its own DMA interface. It currently implements noop bmdma ops to avoid crashing ata_bmdma_error_handler() which BTW actually is EH for SFF drivers. This patch makes ata_bmdma_error_handler() dereference bmdma ops iff bmdma_addr is initialized as done in ata_bmdma_post_internal_cmd. This change allows pdc_adma to standardize ops and use SFF error_handler and post_internal_cmd. Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Mark Lord <liml@rtr.ca> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17libata: kill ata_chk_status()Tejun Heo
ata_chk_status() just calls ops->check_status and it only adds confusion with other status functions. Kill it. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17libata: move ata_pci_default_filter() out of CONFIG_PCITejun Heo
ata_pci_default_filter() doesn't really have anything to do with PCI. It's generally applicable to BMDMA controllers. Move it out of CONFIG_PCI. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17libata: reorganize SFF related stuffTejun Heo
* Move SFF related functions from libata-core.c to libata-sff.c. ata_[bmdma_]sff_port_ops, ata_devchk(), ata_dev_try_classify(), ata_std_dev_select(), ata_tf_to_host(), ata_busy_sleep(), ata_wait_after_reset(), ata_wait_ready(), ata_bus_post_reset(), ata_bus_softreset(), ata_bus_reset(), ata_std_softreset(), sata_std_hardreset(), ata_fill_sg(), ata_fill_sg_dumb(), ata_qc_prep(), ata_dump_qc_prep(), ata_data_xfer(), ata_data_xfer_noirq(), ata_pio_sector(), ata_pio_sectors(), atapi_send_cdb(), __atapi_pio_bytes(), atapi_pio_bytes(), ata_hsm_ok_in_wq(), ata_hsm_qc_complete(), ata_hsm_move(), ata_pio_task(), ata_qc_issue_prot(), ata_host_intr(), ata_interrupt(), ata_std_ports() * Make ata_pio_queue_task() global as it's now called from libata-sff.c. * Move SFF related stuff in include/linux/libata.h and drivers/ata/libata.h into one place. While at it, move timing constants into the global enum definition and fortify comments a bit. This patch strictly moves stuff around and as such doesn't cause any functional difference. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17libata: reorder functions in libata-sff.cTejun Heo
Reorder functions in drivers/ata/libata-sff.c such that functions generally follow ops table order and init functions come last. This is in preparation of SFF cleanup. This patch strictly moves stuff around and as such doesn't cause any functional difference. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17libata: make reset related methods proper port operationsTejun Heo
Currently reset methods are not specified directly in the ata_port_operations table. If a LLD wants to use custom reset methods, it should construct and use a error_handler which uses those reset methods. It's done this way for two reasons. First, the ops table already contained too many methods and adding four more of them would noticeably increase the amount of necessary boilerplate code all over low level drivers. Second, as ->error_handler uses those reset methods, it can get confusing. ie. By overriding ->error_handler, those reset ops can be made useless making layering a bit hazy. Now that ops table uses inheritance, the first problem doesn't exist anymore. The second isn't completely solved but is relieved by providing default values - most drivers can just override what it has implemented and don't have to concern itself about higher level callbacks. In fact, there currently is no driver which actually modifies error handling behavior. Drivers which override ->error_handler just wraps the standard error handler only to prepare the controller for EH. I don't think making ops layering strict has any noticeable benefit. This patch makes ->prereset, ->softreset, ->hardreset, ->postreset and their PMP counterparts propoer ops. Default ops are provided in the base ops tables and drivers are converted to override individual reset methods instead of creating custom error_handler. * ata_std_error_handler() doesn't use sata_std_hardreset() if SCRs aren't accessible. sata_promise doesn't need to use separate error_handlers for PATA and SATA anymore. * softreset is broken for sata_inic162x and sata_sx4. As libata now always prefers hardreset, this doesn't really matter but the ops are forced to NULL using ATA_OP_NULL for documentation purpose. * pata_hpt374 needs to use different prereset for the first and second PCI functions. This used to be done by branching from hpt374_error_handler(). The proper way to do this is to use separate ops and port_info tables for each function. Converted. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17libata: stop overloading port_info->private_dataTejun Heo
port_info->private_data is currently used for two purposes - to record private data about the port_info or to specify host->private_data to use when allocating ata_host. This overloading is confusing and counter-intuitive in that port_info->private_data becomes host->private_data instead of port->private_data. In addition, port_info and host don't correspond to each other 1-to-1. Currently, the first non-NULL port_info->private_data is used. This patch makes port_info->private_data just be what it is - private_data for the port_info where LLD can jot down extra info. libata no longer sets host->private_data to the first non-NULL port_info->private_data, @host_priv argument is added to ata_pci_init_one() instead. LLDs which use ata_pci_init_one() can use this argument to pass in pointer to host private data. LLDs which don't should use init-register model anyway and can initialize host->private_data directly. Adding @host_priv instead of using init-register model for LLDs which use ata_pci_init_one() is suggested by Alan Cox. Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
2008-04-17libata: make ata_pci_init_one() not use ops->irq_handler and pi->shtTejun Heo
ata_pci_init_one() is the only function which uses ops->irq_handler and pi->sht. Other initialization functions take the same information as arguments. This causes confusion and duplicate unused entries in structures. Make ata_pci_init_one() take sht as an argument and use ata_interrupt implicitly. All current users use ata_interrupt and if different irq handler is necessary open coding ata_pci_init_one() using ata_prepare_sff_host() and ata_activate_sff_host can be done under ten lines including error handling and driver which requires custom interrupt handler is likely to require custom initialization anyway. As ata_pci_init_one() was the last user of ops->irq_handler, this patch also kills the field. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17libata: implement and use ata_noop_irq_clear()Tejun Heo
->irq_clear() is used to clear IRQ bit of a SFF controller and isn't useful for drivers which don't use libata SFF HSM implementation. However, it's a required callback and many drivers implement their own noop version as placeholder. This patch implements ata_noop_irq_clear and use it to replace those custom placeholders. Also, SFF drivers which don't support BMDMA don't need to use ata_bmdma_irq_clear(). It becomes noop if BMDMA address isn't initialized. Convert them to use ata_noop_irq_clear(). Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-03-10libata-sff: handle controllers w/o ctl registerTejun Heo
SFF incorrectly assumed that ctl register is available for all controllers while some old SFF controllers don't have ctl register. Make SFF handle controllers w/o ctl register by conditionalizing ctl register access and softreset method. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23libata: factor out ata_pci_activate_sff_host() from ata_pci_one()Tejun Heo
Factor out ata_pci_activate_sff_host() from ata_pci_one(). This does about the same thing as ata_host_activate() but needs to be separate because SFF controllers use different and multiple IRQs in legacy mode. This will be used to make SFF LLD initialization more flexible. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23libata: use dev_driver_string() instead of "libata" in libata-sff.cTejun Heo
libata-sff code used DRV_NAME which is hardcoded to "libata" when requesting resources. Use dev_driver_string() such that low level driver names are used in resource listing. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23libata: rename ATA_PROT_ATAPI_* to ATAPI_PROT_*Tejun Heo
ATA_PROT_ATAPI_* are ugly and naming schemes between ATA_PROT_* and ATA_PROT_ATAPI_* are inconsistent causing confusion. Rename them to ATAPI_PROT_* and make them consistent with ATA counterpart. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-01-23libata-sff: tf_loadAlan Cox
Jeff said he preferred that the SFF tf_load followed the spec and we documented that anyone who needed different overrode it, rather than it using the ->check_status methods. No driver relies on the current behaviour. Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-10libata-sff: PCI IRQ handling fixAlan Cox
It is legitimate (although annoying and silly) for a PCI IDE controller not to be assigned an interrupt and to be polled. The libata-sff code should therefore not try and request IRQ 0 in this case. Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-23[libata] checkpatch-inspired cleanupsJeff Garzik
Tackle the relatively sane complaints of checkpatch --file. The vast majority is indentation and whitespace changes, the rest are * #include fixes * printk KERN_xxx prefix addition * BSS/initializer cleanups Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2007-10-19Fix misspellings of "system", "controller", "interrupt" and "necessary".Robert P. J. Day
Fix the various misspellings of "system", controller", "interrupt" and "[un]necessary". Signed-off-by: Robert P. J. Day <rpjday@mindspring.com> Signed-off-by: Adrian Bunk <bunk@kernel.org>
2007-10-18Merge branch 'upstream-linus' of ↵Linus Torvalds
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev * 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev: [libata] kill ata_sg_is_last() Update libata driver for bf548 atapi controller against the 2.6.24 tree. libata-sff: Correct use of check_status() drivers/ata: add support to Freescale 3.0Gbps SATA Controller pata_acpi: fix build breakage if !CONFIG_PM